Pull Devicetree updates from Rob Herring:
- DT binding schema examples are now validated against the schemas.
Various examples are fixed due to that.
- Sync dtc with upstream version v1.5.0-30-g702c1b6c0e73
- Initial schemas for networking bindings. This includes ethernet, phy
and mdio common bindings with several Allwinner and stmmac converted
to the schema.
- Conversion of more Arm top-level SoC/board bindings to DT schema
- Conversion of PSCI binding to DT schema
- Rework Arm CPU schema to coexist with other CPU schemas
- Add a bunch of missing vendor prefixes and new ones for SoChip,
Sipeed, Kontron, B&R Industrial Automation GmbH, and Espressif
- Add Mediatek UART RX wakeup support to binding
- Add reset to ST UART binding
- Remove some Linuxisms from the endianness common-properties.txt
binding
- Make the flattened DT read-only after init
- Ignore disabled reserved memory nodes
- Clean-up some dead code in FDT functions
* tag 'devicetree-for-5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (56 commits)
dt-bindings: vendor-prefixes: add Sipeed
dt-bindings: vendor-prefixes: add SoChip
dt-bindings: 83xx-512x-pci: Drop cell-index property
dt-bindings: serial: add documentation for Rx in-band wakeup support
dt-bindings: arm: Convert RDA Micro board/soc bindings to json-schema
of: unittest: simplify getting the adapter of a client
of/fdt: pass early_init_dt_reserve_memory_arch() with bool type nomap
of/platform: Drop superfluous cast in of_device_make_bus_id()
dt-bindings: usb: ehci: Fix example warnings
dt-bindings: net: Use phy-mode instead of phy-connection-type
dt-bindings: simple-framebuffer: Add requirement for pipelines
dt-bindings: display: Fix simple-framebuffer example
dt-bindings: net: mdio: Add child nodes
dt-bindings: net: mdio: Add address and size cells
dt-bindings: net: mdio: Add a nodename pattern
dt-bindings: mtd: sunxi-nand: Drop 'maxItems' from child 'reg' property
dt-bindings: arm: Limit cpus schema to only check Arm 'cpu' nodes
dt-bindings: backlight: lm3630a: correct schema validation
dt-bindings: net: dwmac: Deprecate the PHY reset properties
dt-bindings: net: sun8i-emac: Convert the binding to a schemas
...
Pull Documentation updates from Jonathan Corbet:
"It's been a relatively busy cycle for docs:
- A fair pile of RST conversions, many from Mauro. These create more
than the usual number of simple but annoying merge conflicts with
other trees, unfortunately. He has a lot more of these waiting on
the wings that, I think, will go to you directly later on.
- A new document on how to use merges and rebases in kernel repos,
and one on Spectre vulnerabilities.
- Various improvements to the build system, including automatic
markup of function() references because some people, for reasons I
will never understand, were of the opinion that
:c:func:``function()`` is unattractive and not fun to type.
- We now recommend using sphinx 1.7, but still support back to 1.4.
- Lots of smaller improvements, warning fixes, typo fixes, etc"
* tag 'docs-5.3' of git://git.lwn.net/linux: (129 commits)
docs: automarkup.py: ignore exceptions when seeking for xrefs
docs: Move binderfs to admin-guide
Disable Sphinx SmartyPants in HTML output
doc: RCU callback locks need only _bh, not necessarily _irq
docs: format kernel-parameters -- as code
Doc : doc-guide : Fix a typo
platform: x86: get rid of a non-existent document
Add the RCU docs to the core-api manual
Documentation: RCU: Add TOC tree hooks
Documentation: RCU: Rename txt files to rst
Documentation: RCU: Convert RCU UP systems to reST
Documentation: RCU: Convert RCU linked list to reST
Documentation: RCU: Convert RCU basic concepts to reST
docs: filesystems: Remove uneeded .rst extension on toctables
scripts/sphinx-pre-install: fix out-of-tree build
docs: zh_CN: submitting-drivers.rst: Remove a duplicated Documentation/
Documentation: PGP: update for newer HW devices
Documentation: Add section about CPU vulnerabilities for Spectre
Documentation: platform: Delete x86-laptop-drivers.txt
docs: Note that :c:func: should no longer be used
...
Pull locking updates from Ingo Molnar:
"The main changes in this cycle are:
- rwsem scalability improvements, phase #2, by Waiman Long, which are
rather impressive:
"On a 2-socket 40-core 80-thread Skylake system with 40 reader
and writer locking threads, the min/mean/max locking operations
done in a 5-second testing window before the patchset were:
40 readers, Iterations Min/Mean/Max = 1,807/1,808/1,810
40 writers, Iterations Min/Mean/Max = 1,807/50,344/151,255
After the patchset, they became:
40 readers, Iterations Min/Mean/Max = 30,057/31,359/32,741
40 writers, Iterations Min/Mean/Max = 94,466/95,845/97,098"
There's a lot of changes to the locking implementation that makes
it similar to qrwlock, including owner handoff for more fair
locking.
Another microbenchmark shows how across the spectrum the
improvements are:
"With a locking microbenchmark running on 5.1 based kernel, the
total locking rates (in kops/s) on a 2-socket Skylake system
with equal numbers of readers and writers (mixed) before and
after this patchset were:
# of Threads Before Patch After Patch
------------ ------------ -----------
2 2,618 4,193
4 1,202 3,726
8 802 3,622
16 729 3,359
32 319 2,826
64 102 2,744"
The changes are extensive and the patch-set has been through
several iterations addressing various locking workloads. There
might be more regressions, but unless they are pathological I
believe we want to use this new implementation as the baseline
going forward.
- jump-label optimizations by Daniel Bristot de Oliveira: the primary
motivation was to remove IPI disturbance of isolated RT-workload
CPUs, which resulted in the implementation of batched jump-label
updates. Beyond the improvement of the real-time characteristics
kernel, in one test this patchset improved static key update
overhead from 57 msecs to just 1.4 msecs - which is a nice speedup
as well.
- atomic64_t cross-arch type cleanups by Mark Rutland: over the last
~10 years of atomic64_t existence the various types used by the
APIs only had to be self-consistent within each architecture -
which means they became wildly inconsistent across architectures.
Mark puts and end to this by reworking all the atomic64
implementations to use 's64' as the base type for atomic64_t, and
to ensure that this type is consistently used for parameters and
return values in the API, avoiding further problems in this area.
- A large set of small improvements to lockdep by Yuyang Du: type
cleanups, output cleanups, function return type and othr cleanups
all around the place.
- A set of percpu ops cleanups and fixes by Peter Zijlstra.
- Misc other changes - please see the Git log for more details"
* 'locking-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (82 commits)
locking/lockdep: increase size of counters for lockdep statistics
locking/atomics: Use sed(1) instead of non-standard head(1) option
locking/lockdep: Move mark_lock() inside CONFIG_TRACE_IRQFLAGS && CONFIG_PROVE_LOCKING
x86/jump_label: Make tp_vec_nr static
x86/percpu: Optimize raw_cpu_xchg()
x86/percpu, sched/fair: Avoid local_clock()
x86/percpu, x86/irq: Relax {set,get}_irq_regs()
x86/percpu: Relax smp_processor_id()
x86/percpu: Differentiate this_cpu_{}() and __this_cpu_{}()
locking/rwsem: Guard against making count negative
locking/rwsem: Adaptive disabling of reader optimistic spinning
locking/rwsem: Enable time-based spinning on reader-owned rwsem
locking/rwsem: Make rwsem->owner an atomic_long_t
locking/rwsem: Enable readers spinning on writer
locking/rwsem: Clarify usage of owner's nonspinaable bit
locking/rwsem: Wake up almost all readers in wait queue
locking/rwsem: More optimal RT task handling of null owner
locking/rwsem: Always release wait_lock before waking up tasks
locking/rwsem: Implement lock handoff to prevent lock starvation
locking/rwsem: Make rwsem_spin_on_owner() return owner state
...
Build of htmldocs fails for out-of-tree builds:
$ make V=1 O=~/build/kernel/ htmldocs
make -C /home/rppt/build/kernel -f /home/rppt/git/linux-docs/Makefile htmldocs
make[1]: Entering directory '/home/rppt/build/kernel'
make -f /home/rppt/git/linux-docs/scripts/Makefile.build obj=scripts/basic
rm -f .tmp_quiet_recordmcount
make -f /home/rppt/git/linux-docs/scripts/Makefile.build obj=Documentation htmldocs
Can't open Documentation/conf.py at /home/rppt/git/linux-docs/scripts/sphinx-pre-install line 230.
/home/rppt/git/linux-docs/Documentation/Makefile:80: recipe for target 'htmldocs' failed
make[2]: *** [htmldocs] Error 2
The scripts/sphinx-pre-install is trying to open files in the current
directory which is $KBUILD_OUTPUT rather than in $srctree.
Fix it.
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Reviewed-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
We now have better automarkup in sphinx itself and, besides, this markup
was incorrect and left :c:func: gunk in the processed docs. Sort of
discouraging that nobody ever noticed...:)
As a first step toward the removal of impenetrable regex magic from
kernel-doc it's a tiny one, but you have to start somewhere.
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Pull in SPDX tag conversion from upstream dtc. This will replace the
conversion done in the kernel tree copy in v5.2-rc2.
This adds the following commits from upstream:
702c1b6c0e73 README.license: Update to reflect SPDX tag usage
4097bbffcf1d dtc: Add GPLv2 SPDX tags to files missing license text
94f87cd5b7c5 libfdt: Add dual GPL/BSD SPDX tags to files missing license text
c4ffc05574b1 tests: Replace license boilerplate with SPDX tags
a5ac29baacd2 pylibfdt: Replace dual GPLv2/BSD license boilerplate with SPDX tags
7fb0f4db2eb7 libfdt: Replace GPL/BSD boilerplate/reference with SPDX tags
acfe84f2c47e dtc: Replace GPLv2 boilerplate/reference with SPDX tags
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Rob Herring <robh@kernel.org>
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation #
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 4122 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When there's no Documentation/output directory, the script will
complain about those missing references:
Documentation/doc-guide/sphinx.rst: Documentation/output
Documentation/doc-guide/sphinx.rst: Documentation/output
Documentation/process/howto.rst: Documentation/output
Documentation/translations/it_IT/doc-guide/sphinx.rst: Documentation/output
Documentation/translations/it_IT/doc-guide/sphinx.rst: Documentation/output
Documentation/translations/it_IT/process/howto.rst: Documentation/output
Documentation/translations/ja_JP/howto.rst: Documentation/output
Documentation/translations/ko_KR/howto.rst: Documentation/output
Those are false positives, so add an ignore rule for them.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
The conversion here is really trivial: just a bunch of title
markups and very few puntual changes is enough to make it to
be parsed by Sphinx and generate a nice html.
The conversion is actually:
- add blank lines and identation in order to identify paragraphs;
- fix tables markups;
- add some lists markups;
- mark literal blocks;
- adjust title markups.
At its new index.rst, let's add a :orphan: while this is not linked to
the main index.rst file, in order to avoid build warnings.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Convert the TCM docs to ReST format and add them to the
bookset.
This has a mix of userspace-faced and Kernelspace faced
docs. Still, it sounds a better candidate to be added at
the kernel API set of docs.
The conversion is actually:
- add blank lines and identation in order to identify paragraphs;
- fix tables markups;
- add some lists markups;
- mark literal blocks;
- adjust title markups.
At its new index.rst, let's add a :orphan: while this is not linked to
the main index.rst file, in order to avoid build warnings.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
The kbuild documentation clearly shows that the documents
there are written at different times: some use markdown,
some use their own peculiar logic to split sections.
Convert everything to ReST without affecting too much
the author's style and avoiding adding uneeded markups.
The conversion is actually:
- add blank lines and identation in order to identify paragraphs;
- fix tables markups;
- add some lists markups;
- mark literal blocks;
- adjust title markups.
At its new index.rst, let's add a :orphan: while this is not linked to
the main index.rst file, in order to avoid build warnings.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
At least for ARM64 kernels compiled with the crosstoolchain from
Debian/stretch or with the toolchain from kernel.org the line number is
not decoded correctly by 'decode_stacktrace.sh':
$ echo "[ 136.513051] f1+0x0/0xc [kcrash]" | \
CROSS_COMPILE=/opt/gcc-8.1.0-nolibc/aarch64-linux/bin/aarch64-linux- \
./scripts/decode_stacktrace.sh /scratch/linux-arm64/vmlinux \
/scratch/linux-arm64 \
/nfs/debian/lib/modules/4.20.0-devel
[ 136.513051] f1 (/linux/drivers/staging/kcrash/kcrash.c:68) kcrash
If addr2line from the toolchain is used the decoded line number is correct:
[ 136.513051] f1 (/linux/drivers/staging/kcrash/kcrash.c:57) kcrash
Link: http://lkml.kernel.org/r/20190527083425.3763-1-manut@linutronix.de
Signed-off-by: Manuel Traut <manut@linutronix.de>
Acked-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This adds the following commits from upstream:
87963ee20693 livetree: add missing type markers in generated overlay properties
825146d13dc0 Fix typos in various documentation and source files
25bb080c18d1 Update the GPL2 text to the latest revision
243176c4ce84 Fix bogus error on rebuild
ce01b21098a4 libfdt: Add FDT_CREATE_FLAG_NO_NAME_DEDUP flag that trades size for speed
fbb62754ce45 libfdt: Introduce fdt_create_with_flags()
228a44cce857 libfdt: Ensure fdt_add_property frees allocated name string on failure
8f695676227b Avoid assertion in check_interrupts_property()
5c3513f68921 Link tools and tests against libfdt shared library
00f9febf9c16 tests: Rename tests.sh to testutils.sh
c5d45188f923 Clean up LDLIBS handling
6ef8fcd05b74 Rebuild libfdt shared object if versioning linker script changes
26ee65a16c38 Use Python3 by default
cca6546244cb libfdt: Make fdt_get_max_phandle() an inline
730875016a6a libfdt: Add phandle generation helper
7dfb61ba96b1 libfdt: Use fdt_find_max_phandle()
2bc5b66d7f6c libfdt: Add new maximum phandle lookup function
7fcf8208b8a9 libfdt: add fdt_append_addrrange()
ae795b2db7a4 checks: Do not omit nodes with labels if symbol generation is requested
eac2ad495b29 Update version.lds again
f67b47135523 Revert "libfdt: Add phandle generation helper"
54ea41c22415 libfdt: Add phandle generation helper
4762ad051ee0 checks: Fix spelling in check_graph_endpoint
d37f6b20107e Bump version to v1.5.0
a4b1a307ff3a pylibfdt:tests: Extend the way how to find a Python module
625dd8aaf20f pylibfdt: Change how passing tests are recognized
364631626bb7 pylibfdt: Test fdt.setprop take bytes on Python 3, add error handling
cb0f454f73cc pylibfdt: check_err accepts only integer as a first argument.
4b68c6b3605a pylibfdt: Proper handling of bytes/unicode strings and octal literals
78e113e81c9d Use PRIxPTR for printing uintptr_t values
ea7a8f6dad67 libfdt: Fix FDT_ERR_NOTFOUND typos in documentation
5aafd7ca43e0 libfdt: Fix fdt_getprop_by_offset() parameter name in documentation
7cbc550f903b checks: Add unit address check if node is enabled
Signed-off-by: Rob Herring <robh@kernel.org>
Pull yet more SPDX updates from Greg KH:
"Another round of SPDX header file fixes for 5.2-rc4
These are all more "GPL-2.0-or-later" or "GPL-2.0-only" tags being
added, based on the text in the files. We are slowly chipping away at
the 700+ different ways people tried to write the license text. All of
these were reviewed on the spdx mailing list by a number of different
people.
We now have over 60% of the kernel files covered with SPDX tags:
$ ./scripts/spdxcheck.py -v 2>&1 | grep Files
Files checked: 64533
Files with SPDX: 40392
Files with errors: 0
I think the majority of the "easy" fixups are now done, it's now the
start of the longer-tail of crazy variants to wade through"
* tag 'spdx-5.2-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (159 commits)
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 450
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 449
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 448
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 446
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 445
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 444
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 443
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 442
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 441
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 440
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 438
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 437
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 436
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 435
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 434
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 433
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 432
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 431
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 430
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 429
...
While this doesn't make sense for production Kernels, in order to
avoid regressions when documents are touched, let's add a
check target at the make file.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
To print the pathname that will be used by shell in the current
environment, 'command -v' is a standardized way. [1]
'which' is also often used in scripts, but it is less portable.
When I worked on commit bd55f96fa9 ("kbuild: refactor cc-cross-prefix
implementation"), I was eager to use 'command -v' but it did not work.
(The reason is explained below.)
I kept 'which' as before but got rid of '> /dev/null 2>&1' as I
thought it was no longer needed. Sorry, I was wrong.
It works well on my Ubuntu machine, but Alexey Brodkin reports noisy
warnings on CentOS7 when 'which' fails to find the given command in
the PATH environment.
$ which foo
which: no foo in (/usr/local/sbin:/usr/local/bin:/usr/sbin:/usr/bin:/sbin:/bin)
Given that behavior of 'which' depends on system (and it may not be
installed by default), I want to try 'command -v' once again.
The specification [1] clearly describes the behavior of 'command -v'
when the given command is not found:
Otherwise, no output shall be written and the exit status shall reflect
that the name was not found.
However, we need a little magic to use 'command -v' from Make.
$(shell ...) passes the argument to a subshell for execution, and
returns the standard output of the command.
Here is a trick. GNU Make may optimize this by executing the command
directly instead of forking a subshell, if no shell special characters
are found in the command and omitting the subshell will not change the
behavior.
In this case, no shell special character is used. So, Make will try
to run it directly. However, 'command' is a shell-builtin command,
then Make would fail to find it in the PATH environment:
$ make ARCH=m68k defconfig
make: command: Command not found
make: command: Command not found
make: command: Command not found
In fact, Make has a table of shell-builtin commands because it must
ask the shell to execute them.
Until recently, 'command' was missing in the table.
This issue was fixed by the following commit:
| commit 1af314465e5dfe3e8baa839a32a72e83c04f26ef
| Author: Paul Smith <psmith@gnu.org>
| Date: Sun Nov 12 18:10:28 2017 -0500
|
| * job.c: Add "command" as a known shell built-in.
|
| This is not a POSIX shell built-in but it's common in UNIX shells.
| Reported by Nick Bowler <nbowler@draconx.ca>.
Because the latest release is GNU Make 4.2.1 in 2016, this commit is
not included in any released versions. (But some distributions may
have back-ported it.)
We need to trick Make to spawn a subshell. There are various ways to
do so:
1) Use a shell special character '~' as dummy
$(shell : ~; command -v $(c)gcc)
2) Use a variable reference that always expands to the empty string
(suggested by David Laight)
$(shell command$${x:+} -v $(c)gcc)
3) Use redirect
$(shell command -v $(c)gcc 2>/dev/null)
I chose 3) to not confuse people. The stderr would not be polluted
anyway, but it will provide extra safety, and is easy to understand.
Tested on Make 3.81, 3.82, 4.0, 4.1, 4.2, 4.2.1
[1] http://pubs.opengroup.org/onlinepubs/9699919799/utilities/command.html
Fixes: bd55f96fa9 ("kbuild: refactor cc-cross-prefix implementation")
Cc: linux-stable <stable@vger.kernel.org> # 5.1
Reported-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Tested-by: Alexey Brodkin <abrodkin@synopsys.com>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation version 2 of the license
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 315 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Armijn Hemel <armijn@tjaldur.nl>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190531190115.503150771@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program file is free software you can redistribute it and or
modify it under the terms of the gnu general public license as
published by the free software foundation version 2 of the license
this program is distributed in the hope that it will be useful but
without any warranty without even the implied warranty of
merchantability or fitness for a particular purpose see the gnu
general public license for more details you should have received a
copy of the gnu general public license along with this program in a
file named copying if not write to the free software foundation inc
51 franklin street fifth floor boston ma 02110 1301 usa
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 1 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190531081038.017566012@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program file is free software you can redistribute it and or
modify it under the terms of the gnu general public license as
published by the free software foundation version 2 of the license
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 1 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Armijn Hemel <armijn@tjaldur.nl>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190531081036.527324761@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The following error occurs for the `make ARCH=arm64 checkstack` case:
aarch64-linux-gnu-objdump -d vmlinux $(find . -name '*.ko') | \
perl ./scripts/checkstack.pl arm64
wrong or unknown architecture "arm64"
As suggested by Masahiro Yamada, fix the above error using regular
expressions in the same way it was fixed for the `ARCH=x86` case via
commit fda9f9903b ("scripts/checkstack.pl: automatically handle
32-bit and 64-bit mode for ARCH=x86").
Suggested-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: George G. Davis <george_davis@mentor.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The buildtar script might want to invoke a make, so tell the parent
make to pass the jobserver token pipe to the subcommand by prefixing
the command with a +.
This addresses the issue seen here:
/bin/sh ../scripts/package/buildtar tar-pkg
make[3]: warning: jobserver unavailable: using -j1. Add '+' to parent make rule.
See https://www.gnu.org/software/make/manual/html_node/Job-Slots.html
for more information.
Signed-off-by: Trevor Bourget <tgb.kernel@gmail.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Adding SPDX license identifier is pretty safe; however, here is one
exception.
Since commit ec8f24b7fa ("treewide: Add SPDX license identifier -
Makefile/Kconfig"), "make testconfig" would not pass.
When Kconfig detects a circular file inclusion, it displays error
messages with a file name and a line number prefixed to each line.
The unit test checks if Kconfig emits the error messages correctly
(this also checks the line number correctness).
Now that the test input has the SPDX license identifier at the very top,
the line numbers in the expected stderr should be incremented by 1.
Fixes: ec8f24b7fa ("treewide: Add SPDX license identifier - Makefile/Kconfig")
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Merge misc fixes from Andrew Morton:
"Various fixes and followups"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
mm, compaction: make sure we isolate a valid PFN
include/linux/generic-radix-tree.h: fix kerneldoc comment
kernel/signal.c: trace_signal_deliver when signal_group_exit
drivers/iommu/intel-iommu.c: fix variable 'iommu' set but not used
spdxcheck.py: fix directory structures
kasan: initialize tag to 0xff in __kasan_kmalloc
z3fold: fix sheduling while atomic
scripts/gdb: fix invocation when CONFIG_COMMON_CLK is not set
mm/gup: continue VM_FAULT_RETRY processing even for pre-faults
ocfs2: fix error path kobject memory leak
memcg: make it work on sparse non-0-node systems
mm, memcg: consider subtrees in memory.events
prctl_set_mm: downgrade mmap_sem to read lock
prctl_set_mm: refactor checks from validate_prctl_map
kernel/fork.c: make max_threads symbol static
arch/arm/boot/compressed/decompress.c: fix build error due to lz4 changes
arch/parisc/configs/c8000_defconfig: remove obsoleted CONFIG_DEBUG_SLAB_LEAK
mm/vmalloc.c: fix typo in comment
lib/sort.c: fix kernel-doc notation warnings
mm: fix Documentation/vm/hmm.rst Sphinx warnings
The LICENSE directory has recently changed structure and this makes
spdxcheck fails as per below:
FAIL: "Blob or Tree named 'other' not found"
Traceback (most recent call last):
File "scripts/spdxcheck.py", line 240, in <module>
spdx = read_spdxdata(repo)
File "scripts/spdxcheck.py", line 41, in read_spdxdata
for el in lictree[d].traverse():
[...]
KeyError: "Blob or Tree named 'other' not found"
Fix the script to restore the correctness on checkpatch License checking.
References: 62be257e98 ("LICENSES: Rename other to deprecated")
References: 8ea8814fcd ("LICENSES: Clearly mark dual license only licenses")
Link: http://lkml.kernel.org/r/20190523084755.56739-1-vincenzo.frascino@arm.com
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Cc: Joe Perches <joe@perches.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jeremy Cline <jcline@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull gcc-plugins fix from Kees Cook:
"Handle unusual header environment, fixing a redefined macro error
under a Darwin build host"
* tag 'gcc-plugins-v5.2-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
gcc-plugins: Fix build failures under Darwin host
Pull yet more SPDX updates from Greg KH:
"Here is another set of reviewed patches that adds SPDX tags to
different kernel files, based on a set of rules that are being used to
parse the comments to try to determine that the license of the file is
"GPL-2.0-or-later" or "GPL-2.0-only". Only the "obvious" versions of
these matches are included here, a number of "non-obvious" variants of
text have been found but those have been postponed for later review
and analysis.
There is also a patch in here to add the proper SPDX header to a bunch
of Kbuild files that we have missed in the past due to new files being
added and forgetting that Kbuild uses two different file names for
Makefiles. This issue was reported by the Kbuild maintainer.
These patches have been out for review on the linux-spdx@vger mailing
list, and while they were created by automatic tools, they were
hand-verified by a bunch of different people, all whom names are on
the patches are reviewers"
* tag 'spdx-5.2-rc3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (82 commits)
treewide: Add SPDX license identifier - Kbuild
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 225
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 224
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 223
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 222
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 221
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 220
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 218
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 217
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 216
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 215
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 214
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 213
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 211
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 210
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 209
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 207
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 206
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 203
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 201
...
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0
Reported-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 3 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version [author] [kishon] [vijay] [abraham]
[i] [kishon]@[ti] [com] this program is distributed in the hope that
it will be useful but without any warranty without even the implied
warranty of merchantability or fitness for a particular purpose see
the gnu general public license for more details
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version [author] [graeme] [gregory]
[gg]@[slimlogic] [co] [uk] [author] [kishon] [vijay] [abraham] [i]
[kishon]@[ti] [com] [based] [on] [twl6030]_[usb] [c] [author] [hema]
[hk] [hemahk]@[ti] [com] this program is distributed in the hope
that it will be useful but without any warranty without even the
implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 1105 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070033.202006027@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details you
should have received a copy of the gnu general public license along
with this program if not write to the free software foundation inc
59 temple place suite 330 boston ma 02111 1307 usa
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 1334 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070033.113240726@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
At DT, files are being renamed to jason. Teach the script how to
handle such renames when used in fix mode.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
There's a false positive on perf/util:
tools/perf/util/s390-cpumsf.c: Documentation/perf.data-file-format.txt
The file is there at tools/perf/Documentation/, but the logic
with detects relative documentation references inside tools is
not capable of detecting it.
So, improve it.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
There are at least two cases where a documentation file was gone
for good, but the text still mentions it:
1) drivers/vhost/vhost.c:
the reference for Documentation/virtual/lguest/lguest.c is just
to give credits to the original work that vhost replaced;
2) Documentation/scsi/scsi_mid_low_api.txt:
It gives credit and mentions the old Documentation/Configure.help
file that used to be part of Kernel 2.4.x
As we don't want to keep the script to keep pinpoint to those
every time, let's add a logic at the script to allow it to ignore
valid false-positives like the above.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Only seek for translation renames inside the translation
directory.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Call the script every time a make docs target is selected, on
a simplified check mode.
With this change, the script will set two vars:
$min_version - obtained from `needs_sphinx` var inside
conf.py (currently, '1.3')
$rec_version - obtained from sphinx/requirements.txt.
With those changes, a target like "make htmldocs" will do:
1) If no sphinx-build/sphinx-build3 is found, it will run
the script on normal mode as before, checking for all
system dependencies and providing install hints for the
needed programs and will abort the build;
2) If no sphinx-build/sphinx-build3 is found, but there is
a sphinx_${VER}/bin/activate file, and if
${VER} >= $min_version (string comparation), it will
run in full mode, and will recommend to activate the
virtualenv. If there are multiple virtualenvs, it
will string sort the versions, recommending the
highest version and will abort the build;
3) If Sphinx is detected but has a version lower than
$min_version, it will run in full mode - with will
recommend creating a virtual env using sphinx/requirements.txt,
and will abort the build.
4) If Sphinx is detected and version is lower than
$rec_version, it will run in full mode and will
recommend creating a virtual env using sphinx/requirements.txt.
In this case, it **won't** abort the build.
5) If Sphinx is detected and version is equal or righer than
$rec_version it will return just after detecting the
version ("quick mode"), not checking if are there any
missing dependencies.
Just like before, if one wants to install Sphinx from the
distro, it has to call the script manually and use `--no-virtualenv`
argument to get the hints for his OS:
You should run:
sudo dnf install -y python3-sphinx python3-sphinx_rtd_theme
While here, add a small help for the three optional arguments
for the script.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
RHEL8 was already launched. This test won't get it, and will
do the wrong thing. Ok, we could fix it, but now we check
Sphinx version to ensure that it matches the minimal (1.3),
so there's no need for an explicit check there.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
It is possible that multiple Sphinx virtualenvs are installed
on a given kernel tree. Change the logic to get the latest
version of those, as this is probably what the user wants.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
