Add the basic GICv4 VPE (vcpu in GICv4 parlance) infrastructure
(irqchip, irq domain) that is going to be populated in the following
patches.
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
When a VLPI is reconfigured (enabled, disabled, change in priority),
the full configuration byte must be written, and the caches invalidated.
Also, when using the irq_mask/irq_unmask methods, it is necessary
to disable the doorbell for that particular interrupt (by mapping it
to 1023) on top of clearing the Enable bit.
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
In order to let a VLPI being injected into a guest, the VLPI must
be mapped using the VMAPTI command. When moved to a different vcpu,
it must be moved with the VMOVI command.
These commands are issued via the irq_set_vcpu_affinity method,
making sure we unmap the corresponding host LPI first.
The reverse is also done when the VLPI is unmapped from the guest.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Add the skeleton irq_set_vcpu_affinity method that will be used
to configure VLPIs.
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Add the new GICv4 ITS command definitions, most of them, being
defined in terms of their physical counterparts.
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
We're are going to need to change a bit more than just the enable
bit in the LPI property table in the future. So let's change the
LPI configuration funtion to take a set of bits to be cleared,
and a set of bits to be set.
This way, we'll be able to use it when a guest updates an LPI
property (priority, for example).
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
As we want to use 2-level tables for VCPUs, let's hack the device
table allocator in order to make it slightly more generic. It
will get reused in subsequent patches.
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Just as for the property table, let's move the pending table
allocation to a separate function.
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The VCPU tables can be quite sparse as well, and it makes sense
to use indirect tables as well if possible.
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Move the LPI property table allocation into its own function, as
this is going to be required for those associated with VMs in
the future.
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Most ITS commands do operate on a collection object, and require
a SYNC command to be performed on that collection in order to
guarantee the execution of the first command.
With GICv4 ITS, another set of commands perform similar operations
on a VPE object, and a VSYNC operations must be executed to guarantee
their execution.
Given the similarities (post a command, perform a synchronization
operation on a sync object), it makes sense to reuse the same
mechanism for both class of commands.
Let's start with turning its_send_single_command into a huge macro
that performs the bulk of the work, and a set of helpers that
make this macro usable for the GICv3 ITS commands.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Add the probing code for the ITS VLPI support. This includes
configuring the ITS number if not supporting the single VMOVP
command feature.
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The various LPI definitions are in the middle of the code, and
would be better placed at the beginning, given that we're going
to use some of them much earlier.
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
In order to discover the VLPI properties, we need to iterate over
the redistributor regions. As we already have code that does this,
let's factor it out and make it slightly more generic.
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
UniPhier SoCs contain AIDET (ARM Interrupt Detector). This is intended
to provide additional features that are not covered by GIC. The main
purpose is to provide logic inverter to support low level and falling
edge trigger types for interrupt lines from on-board devices.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
wait_for_range_completion() is nicely busted when handling
wrapping of the command queue, leading to an early exit
instead of waiting for the command to have been executed.
Fortunately, the impact is pretty minor, as it only impair
the detection of an ITS that doesn't make any forward progress
for a whole second. And an ITS should *never* lock up.
Reported-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Armada XP does not only support MSI, but also MSI-X. This patch sets
the MSI_FLAG_PCI_MSIX flag in the interrupt controller driver which
is the only change necessary to enable MSI-X support on this SoC. As
the Linux PCI MSI-X infrastructure takes care of writing the data and
address structures into the BAR specified by the MSI-X controller.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Pull driver core fixes from Greg KH:
"Here are three firmware core fixes for 4.13-rc5.
All three of these fix reported issues and have been floating around
for a few weeks. They have been in linux-next with no reported
problems"
* tag 'driver-core-4.13-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
firmware: avoid invalid fallback aborts by using killable wait
firmware: fix batched requests - send wake up on failure on direct lookups
firmware: fix batched requests - wake all waiters
Pull char/misc fixes from Greg KH:
"Here are two patches for 4.13-rc5.
One is a fix for a reported thunderbolt issue, and the other a fix for
an MEI driver issue. Both have been in linux-next with no reported
issues"
* tag 'char-misc-4.13-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
thunderbolt: Do not enumerate more ports from DROM than the controller has
mei: exclude device from suspend direct complete optimization
Pull tty/serial fixes from Greg KH:
"Here are two tty serial driver fixes for 4.13-rc5. One is a revert of
a -rc1 patch that turned out to not be a good idea, and the other is a
fix for the pl011 serial driver.
Both have been in linux-next with no reported issues"
* tag 'tty-4.13-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
Revert "serial: Delete dead code for CIR serial ports"
tty: pl011: fix initialization order of QDF2400 E44
Pull staging/iio fixes from Greg KH:
"Here are some Staging and IIO driver fixes for 4.13-rc5.
Nothing major, just a number of small fixes for reported issues. All
of these have been in linux-next for a while now with no reported
issues. Full details are in the shortlog"
* tag 'staging-4.13-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: comedi: comedi_fops: do not call blocking ops when !TASK_RUNNING
iio: aspeed-adc: wait for initial sequence.
iio: accel: bmc150: Always restore device to normal mode after suspend-resume
staging:iio:resolver:ad2s1210 fix negative IIO_ANGL_VEL read
iio: adc: axp288: Fix the GPADC pin reading often wrongly returning 0
iio: adc: vf610_adc: Fix VALT selection value for REFSEL bits
iio: accel: st_accel: add SPI-3wire support
iio: adc: Revert "axp288: Drop bogus AXP288_ADC_TS_PIN_CTRL register modifications"
iio: adc: sun4i-gpadc-iio: fix unbalanced irq enable/disable
iio: pressure: st_pressure_core: disable multiread by default for LPS22HB
iio: light: tsl2563: use correct event code
Pull USB fixes from Greg KH:
"Here are a number of small USB driver fixes and new device ids for
4.13-rc5. There is the usual gadget driver fixes, some new quirks for
"messy" hardware, and some new device ids.
All have been in linux-next with no reported issues"
* tag 'usb-4.13-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
USB: serial: pl2303: add new ATEN device id
usb: quirks: Add no-lpm quirk for Moshi USB to Ethernet Adapter
USB: Check for dropped connection before switching to full speed
usb:xhci:Add quirk for Certain failing HP keyboard on reset after resume
usb: renesas_usbhs: gadget: fix unused-but-set-variable warning
usb: renesas_usbhs: Fix UGCTRL2 value for R-Car Gen3
usb: phy: phy-msm-usb: Fix usage of devm_regulator_bulk_get()
usb: gadget: udc: renesas_usb3: Fix usb_gadget_giveback_request() calling
usb: dwc3: gadget: Correct ISOC DATA PIDs for short packets
USB: serial: option: add D-Link DWM-222 device ID
usb: musb: fix tx fifo flush handling again
usb: core: unlink urbs from the tail of the endpoint's urb_list
usb-storage: fix deadlock involving host lock and scsi_done
uas: Add US_FL_IGNORE_RESIDUE for Initio Corporation INIC-3069
USB: hcd: Mark secondary HCD as dead if the primary one died
USB: serial: cp210x: add support for Qivicon USB ZigBee dongle
Pull another MTD fix from Brian Norris:
"An mtdblock regression occurred in -rc1 (all writes were broken!), in
the process of some block subsystem refactoring. Noticed and fixed
last week, but I'm a little slow on the uptake"
* tag 'for-linus-20170812' of git://git.infradead.org/linux-mtd:
mtd: blkdevs: Fix mtd block write failure
All the MTD block write requests are failing with
following error messages
mkfs.ext4 /dev/mtdblock0
print_req_error: I/O error, dev mtdblock0, sector 0
Buffer I/O error on dev mtdblock0, logical block 0,
lost async page write
The control is going to default case after block write request
because of missing return.
Fixes: commit 2a842acab1 ("block: introduce new block status code type")
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Pull xen fixes from Juergen Gross:
"Some fixes for Xen:
- a fix for a regression introduced in 4.13 for a Xen HVM-guest
configured with KASLR
- a fix for a possible deadlock in the xenbus driver when booting the
system
- a fix for lost interrupts in Xen guests"
* tag 'for-linus-4.13b-rc5-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen/events: Fix interrupt lost during irq_disable and irq_enable
xen: avoid deadlock in xenbus
xen: fix hvm guest with kaslr enabled
xen: split up xen_hvm_init_shared_info()
x86: provide an init_mem_mapping hypervisor hook
Pull block fixes from Jens Axboe:
"A set of fixes that should go into this series. This contains:
- Fix from Bart for blk-mq requeue queue running, preventing a
continued loop of run/restart.
- Fix for a bio/blk-integrity issue, in two parts. One from
Christoph, fixing where verification happens, and one from Milan,
for a NULL profile.
- NVMe pull request, most of the changes being for nvme-fc, but also
a few trivial core/pci fixes"
* 'for-linus' of git://git.kernel.dk/linux-block:
nvme: fix directive command numd calculation
nvme: fix nvme reset command timeout handling
nvme-pci: fix CMB sysfs file removal in reset path
lpfc: support nvmet_fc defer_rcv callback
nvmet_fc: add defer_req callback for deferment of cmd buffer return
nvme: strip trailing 0-bytes in wwid_show
block: Make blk_mq_delay_kick_requeue_list() rerun the queue at a quiet time
bio-integrity: only verify integrity on the lowest stacked driver
bio-integrity: Fix regression if profile verify_fn is NULL
Pull MMC fixes from Ulf Hansson:
"MMC core:
- fix lockdep splat when removing mmc_block module
- fix the logic for setting eMMC HS400ES signal voltage
MMC host:
- omap_hsmmc: add CMD23 capability to fix -EIO errors"
* tag 'mmc-v4.13-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
mmc: block: fix lockdep splat when removing mmc_block module
mmc: mmc: correct the logic for setting HS400ES signal voltage
mmc: host: omap_hsmmc: Add CMD23 capability to omap_hsmmc driver
Pull fbdev fixes from Bartlomiej Zolnierkiewicz:
- allow user to disable write combined mapping in efifb driver (Dave
Airlie)
- fix use after free bugs on driver removal in imxfb driver (Dan
Carpenter)
- fix unused variable warning in omapfb driver (Arnd Bergmann)
* tag 'fbdev-v4.13-rc5' of git://github.com/bzolnier/linux:
efifb: allow user to disable write combined mapping.
fbdev: omapfb: remove unused variable
video: fbdev: imxfb: use after free in imxfb_remove()
Pull IOMMU fix from Joerg Roedel:
"Fix a NULL-pointer dereference in arm_smmu_add_device"
* tag 'iommu-fixes-v4.13-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
iommu/arm-smmu: fix null-pointer dereference in arm_smmu_add_device
Pull powerpc fixes from Michael Ellerman:
"All fixes for code that went in this cycle.
- a revert of an optimisation to the syscall exit path, which could
lead to an oops on either older machines or machines with > 1TB of
memory
- disable some deep idle states if the firmware configuration for
them fails
- re-enable HARD/SOFT lockup detectors in defconfigs after a Kconfig
change
- six fairly small patches fixing bugs in our new watchdog code
Thanks to: Gautham R Shenoy, Nicholas Piggin"
* tag 'powerpc-4.13-6' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/watchdog: add locking around init/exit functions
powerpc/watchdog: Fix marking of stuck CPUs
powerpc/watchdog: Fix final-check recovered case
powerpc/watchdog: Moderate touch_nmi_watchdog overhead
powerpc/watchdog: Improve watchdog lock primitive
powerpc: NMI IPI improve lock primitive
powerpc/configs: Re-enable HARD/SOFT lockup detectors
powerpc/powernv/idle: Disable LOSE_FULL_CONTEXT states when stop-api fails
Revert "powerpc/64: Avoid restore_math call if possible in syscall exit"
Commit c54451a "iommu/arm-smmu: Fix the error path in arm_smmu_add_device"
removed fwspec assignment in legacy_binding path as redundant which is
wrong. It needs to be updated after fwspec initialisation in
arm_smmu_register_legacy_master() as it is dereferenced later. Without
this there is a NULL-pointer dereference panic during boot on some hosts.
Signed-off-by: Artem Savkov <asavkov@redhat.com>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Here is a device has xen-pirq-MSI interrupt. Dom0 might lost interrupt
during driver irq_disable/irq_enable. Here is the scenario,
1. irq_disable -> disable_dynirq -> mask_evtchn(irq channel)
2. dev interrupt raised by HW and Xen mark its evtchn as pending
3. irq_enable -> startup_pirq -> eoi_pirq ->
clear_evtchn(channel of irq) -> clear pending status
4. consume_one_event process the irq event without pending bit assert
which result in interrupt lost once
5. No HW interrupt raising anymore.
Now use enable_dynirq for enable_pirq of xen_pirq_chip to remove
eoi_pirq when irq_enable.
Signed-off-by: Liu Shuo <shuo.a.liu@intel.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
When starting the xenwatch thread a theoretical deadlock situation is
possible:
xs_init() contains:
task = kthread_run(xenwatch_thread, NULL, "xenwatch");
if (IS_ERR(task))
return PTR_ERR(task);
xenwatch_pid = task->pid;
And xenwatch_thread() does:
mutex_lock(&xenwatch_mutex);
...
event->handle->callback();
...
mutex_unlock(&xenwatch_mutex);
The callback could call unregister_xenbus_watch() which does:
...
if (current->pid != xenwatch_pid)
mutex_lock(&xenwatch_mutex);
...
In case a watch is firing before xenwatch_pid could be set and the
callback of that watch unregisters a watch, then a self-deadlock would
occur.
Avoid this by setting xenwatch_pid in xenwatch_thread().
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Pull drm fixes from Dave Airlie:
"Nothing too earth shattering here, it just seems like lots of little
things all over the place.
msm has probably the larger amount of changes, but they all seem fine,
otherwise, some rockchip, i915, etnaviv and exynos fixes, along with
one nouveau regression fix for some older GPUs"
* tag 'drm-fixes-for-v4.13-rc5' of git://people.freedesktop.org/~airlied/linux: (35 commits)
drm/nouveau/disp/nv04: avoid creation of output paths
drm: make DRM_STM default n
drm/exynos: forbid creating framebuffers from too small GEM buffers
drm/etnaviv: Fix off-by-one error in reloc checking
drm/i915: fix backlight invert for non-zero minimum brightness
drm/i915/shrinker: Wrap need_resched() inside preempt-disable
drm/i915/perf: fix flex eu registers programming
drm/i915: Fix out-of-bounds array access in bdw_load_gamma_lut
drm/i915/gvt: Change the max length of mmio_reg_rw from 4 to 8
drm/i915/gvt: Initialize MMIO Block with HW state
drm/rockchip: vop: report error when check resource error
drm/rockchip: vop: round_up pitches to word align
drm/rockchip: vop: fix NV12 video display error
drm/rockchip: vop: fix iommu page fault when resume
drm/i915/gvt: clean workload queue if error happened
drm/i915/gvt: change resetting to resetting_eng
drm/msm: gpu: don't abuse dma_alloc for non-DMA allocations
drm/msm: gpu: call qcom_mdt interfaces only for ARCH_QCOM
drm/msm/adreno: Prevent unclocked access when retrieving timestamps
drm/msm: Remove __user from __u64 data types
...
Merge misc fixes from Andrew Morton:
"21 fixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (21 commits)
userfaultfd: replace ENOSPC with ESRCH in case mm has gone during copy/zeropage
zram: rework copy of compressor name in comp_algorithm_store()
rmap: do not call mmu_notifier_invalidate_page() under ptl
mm: fix list corruptions on shmem shrinklist
mm/balloon_compaction.c: don't zero ballooned pages
MAINTAINERS: copy virtio on balloon_compaction.c
mm: fix KSM data corruption
mm: fix MADV_[FREE|DONTNEED] TLB flush miss problem
mm: make tlb_flush_pending global
mm: refactor TLB gathering API
Revert "mm: numa: defer TLB flush for THP migration as long as possible"
mm: migrate: fix barriers around tlb_flush_pending
mm: migrate: prevent racy access to tlb_flush_pending
fault-inject: fix wrong should_fail() decision in task context
test_kmod: fix small memory leak on filesystem tests
test_kmod: fix the lock in register_test_dev_kmod()
test_kmod: fix bug which allows negative values on two config options
test_kmod: fix spelling mistake: "EMTPY" -> "EMPTY"
userfaultfd: hugetlbfs: remove superfluous page unlock in VM_SHARED case
mm: ratelimit PFNs busy info message
...
Commit 0cb64249ca ("firmware_loader: abort request if wait_for_completion
is interrupted") added via 4.0 added support to abort the fallback mechanism
when a signal was detected and wait_for_completion_interruptible() returned
-ERESTARTSYS -- for instance when a user hits CTRL-C. The abort was overly
*too* effective.
When a child process terminates (successful or not) the signal SIGCHLD can
be sent to the parent process which ran the child in the background and
later triggered a sync request for firmware through a sysfs interface which
relies on the fallback mechanism. This signal in turn can be recieved by the
interruptible wait we constructed on firmware_class and detects it as an
abort *before* userspace could get a chance to write the firmware. Upon
failure -EAGAIN is returned, so userspace is also kept in the dark about
exactly what happened.
We can reproduce the issue with the fw_fallback.sh selftest:
Before this patch:
$ sudo tools/testing/selftests/firmware/fw_fallback.sh
...
tools/testing/selftests/firmware/fw_fallback.sh: error - sync firmware request cancelled due to SIGCHLD
After this patch:
$ sudo tools/testing/selftests/firmware/fw_fallback.sh
...
tools/testing/selftests/firmware/fw_fallback.sh: SIGCHLD on sync ignored as expected
Fix this by making the wait killable -- only killable by SIGKILL (kill -9).
We loose the ability to allow userspace to cancel a write with CTRL-C
(SIGINT), however its been decided the compromise to require SIGKILL is
worth the gains.
Chances of this issue occuring are low due to the number of drivers upstream
exclusively relying on the fallback mechanism for firmware (2 drivers),
however this is observed in the field with custom drivers with sysfs
triggers to load firmware. Only distributions relying on the fallback
mechanism are impacted as well. An example reported issue was on Android,
as follows:
1) Android init (pid=1) fork()s (say pid=42) [this child process is totally
unrelated to firmware loading, it could be sleep 2; for all we care ]
2) Android init (pid=1) does a write() on a (driver custom) sysfs file which
ends up calling request_firmware() kernel side
3) The firmware loading fallback mechanism is used, the request is sent to
userspace and pid 1 waits in the kernel on wait_*
4) before firmware loading completes pid 42 dies (for any reason, even
normal termination)
5) Kernel delivers SIGCHLD to pid=1 to tell it a child has died, which
causes -ERESTARTSYS to be returned from wait_*
6) The kernel's wait aborts and return -EAGAIN for the
request_firmware() caller.
Cc: stable <stable@vger.kernel.org> # 4.0
Fixes: 0cb64249ca ("firmware_loader: abort request if wait_for_completion is interrupted")
Suggested-by: "Eric W. Biederman" <ebiederm@xmission.com>
Suggested-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Tested-by: Martin Fuzzey <mfuzzey@parkeon.com>
Reported-by: Martin Fuzzey <mfuzzey@parkeon.com>
Signed-off-by: Luis R. Rodriguez <mcgrof@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix batched requests from waiting forever on failure.
The firmware API batched requests feature has been broken since the API call
request_firmware_direct() was introduced on commit bba3a87e98 ("firmware:
Introduce request_firmware_direct()"), added on v3.14 *iff* the firmware
being requested was not present in *certain kernel builds* [0].
When no firmware is found the worker which goes on to finish never informs
waiters queued up of this, so any batched request will stall in what seems
to be forever (MAX_SCHEDULE_TIMEOUT). Sadly, a reboot will also stall, as
the reboot notifier was only designed to kill custom fallback workers. The
issue seems to the user as a type of soft lockup, what *actually* happens
underneath the hood is a wait call which never completes as we failed to
issue a completion on error.
For device drivers with optional firmware schemes (ie, Intel iwlwifi, or
Netronome -- even though it uses request_firmware() and not
request_firmware_direct()), this could mean that when you boot a system with
multiple cards the firmware will seem to never load on the system, or that
the card is just not responsive even the driver initialization. Due to
differences in scheduling possible this should not always trigger --
one would need to to ensure that multiple requests are in place at the
right time for this to work, also release_firmware() must not be called
prior to any other incoming request. The complexity may not be worth
supporting batched requests in the future given the wait mechanism is
only used also for the fallback mechanism. We'll keep it for now and
just fix it.
Its reported that at least with the Intel WiFi cards on one system this
issue was creeping up 50% of the boots [0].
Before this commit batched requests testing revealed:
============================================================================
CONFIG_FW_LOADER_USER_HELPER_FALLBACK=n
CONFIG_FW_LOADER_USER_HELPER=y
Most common Linux distribution setup.
API-type no-firmware-found firmware-found
----------------------------------------------------------------------
request_firmware() FAIL OK
request_firmware_direct() FAIL OK
request_firmware_nowait(uevent=true) FAIL OK
request_firmware_nowait(uevent=false) FAIL OK
============================================================================
CONFIG_FW_LOADER_USER_HELPER_FALLBACK=n
CONFIG_FW_LOADER_USER_HELPER=n
Only possible if CONFIG_DELL_RBU=n and CONFIG_LEDS_LP55XX_COMMON=n, rare.
API-type no-firmware-found firmware-found
----------------------------------------------------------------------
request_firmware() FAIL OK
request_firmware_direct() FAIL OK
request_firmware_nowait(uevent=true) FAIL OK
request_firmware_nowait(uevent=false) FAIL OK
============================================================================
CONFIG_FW_LOADER_USER_HELPER_FALLBACK=y
CONFIG_FW_LOADER_USER_HELPER=y
Google Android setup.
API-type no-firmware-found firmware-found
----------------------------------------------------------------------
request_firmware() OK OK
request_firmware_direct() FAIL OK
request_firmware_nowait(uevent=true) OK OK
request_firmware_nowait(uevent=false) OK OK
============================================================================
Ater this commit batched testing results:
============================================================================
CONFIG_FW_LOADER_USER_HELPER_FALLBACK=n
CONFIG_FW_LOADER_USER_HELPER=y
Most common Linux distribution setup.
API-type no-firmware-found firmware-found
----------------------------------------------------------------------
request_firmware() OK OK
request_firmware_direct() OK OK
request_firmware_nowait(uevent=true) OK OK
request_firmware_nowait(uevent=false) OK OK
============================================================================
CONFIG_FW_LOADER_USER_HELPER_FALLBACK=n
CONFIG_FW_LOADER_USER_HELPER=n
Only possible if CONFIG_DELL_RBU=n and CONFIG_LEDS_LP55XX_COMMON=n, rare.
API-type no-firmware-found firmware-found
----------------------------------------------------------------------
request_firmware() OK OK
request_firmware_direct() OK OK
request_firmware_nowait(uevent=true) OK OK
request_firmware_nowait(uevent=false) OK OK
============================================================================
CONFIG_FW_LOADER_USER_HELPER_FALLBACK=y
CONFIG_FW_LOADER_USER_HELPER=y
Google Android setup.
API-type no-firmware-found firmware-found
----------------------------------------------------------------------
request_firmware() OK OK
request_firmware_direct() OK OK
request_firmware_nowait(uevent=true) OK OK
request_firmware_nowait(uevent=false) OK OK
============================================================================
[0] https://bugzilla.kernel.org/show_bug.cgi?id=195477
Cc: stable <stable@vger.kernel.org> # v3.14
Fixes: bba3a87e98 ("firmware: Introduce request_firmware_direct()"
Reported-by: Nicolas <nbroeking@me.com>
Reported-by: John Ewalt <jewalt@lgsinnovations.com>
Reported-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Luis R. Rodriguez <mcgrof@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The firmware cache mechanism serves two purposes, the secondary purpose is
not well documented nor understood. This fixes a regression with the
secondary purpose of the firmware cache mechanism: batched requests on
successful lookups. Without this fix *any* time a batched request is
triggered, secondary requests for which the batched request mechanism
was designed for will seem to last forver and seem to never return.
This issue is present for all kernel builds possible, and a hard reset
is required.
The firmware cache is used for:
1) Addressing races with file lookups during the suspend/resume cycle
by keeping firmware in memory during the suspend/resume cycle
2) Batched requests for the same file rely only on work from the first file
lookup, which keeps the firmware in memory until the last
release_firmware() is called
Batched requests *only* take effect if secondary requests come in prior to
the first user calling release_firmware(). The devres name used for the
internal firmware cache is used as a hint other pending requests are
ongoing, the firmware buffer data is kept in memory until the last user of
the buffer calls release_firmware(), therefore serializing requests and
delaying the release until all requests are done.
Batched requests wait for a wakup or signal so we can rely on the first file
fetch to write to the pending secondary requests. Commit 5b02962494
("firmware: do not use fw_lock for fw_state protection") ported the firmware
API to use swait, and in doing so failed to convert complete_all() to
swake_up_all() -- it used swake_up(), loosing the ability for *some* batched
requests to take effect.
We *could* fix this by just using swake_up_all() *but* swait is now known
to be very special use case, so its best to just move away from it. So we
just go back to using completions as before commit 5b02962494 ("firmware:
do not use fw_lock for fw_state protection") given this was using
complete_all().
Without this fix it has been reported plugging in two Intel 6260 Wifi cards
on a system will end up enumerating the two devices only 50% of the time
[0]. The ported swake_up() should have actually handled the case with two
devices, however, *if more than two cards are used* the swake_up() would
not have sufficed. This change is only part of the required fixes for
batched requests. Another fix is provided in the next patch.
This particular change should fix the cases where more than three requests
with the same firmware name is used, otherwise batched requests will wait
for MAX_SCHEDULE_TIMEOUT and just timeout eventually.
Below is a summary of tests triggering batched requests on different
kernel builds.
Before this patch:
============================================================================
CONFIG_FW_LOADER_USER_HELPER_FALLBACK=n
CONFIG_FW_LOADER_USER_HELPER=y
Most common Linux distribution setup.
API-type no-firmware-found firmware-found
----------------------------------------------------------------------
request_firmware() FAIL FAIL
request_firmware_direct() FAIL FAIL
request_firmware_nowait(uevent=true) FAIL FAIL
request_firmware_nowait(uevent=false) FAIL FAIL
============================================================================
CONFIG_FW_LOADER_USER_HELPER_FALLBACK=n
CONFIG_FW_LOADER_USER_HELPER=n
Only possible if CONFIG_DELL_RBU=n and CONFIG_LEDS_LP55XX_COMMON=n, rare.
API-type no-firmware-found firmware-found
----------------------------------------------------------------------
request_firmware() FAIL FAIL
request_firmware_direct() FAIL FAIL
request_firmware_nowait(uevent=true) FAIL FAIL
request_firmware_nowait(uevent=false) FAIL FAIL
============================================================================
CONFIG_FW_LOADER_USER_HELPER_FALLBACK=y
CONFIG_FW_LOADER_USER_HELPER=y
Google Android setup.
API-type no-firmware-found firmware-found
----------------------------------------------------------------------
request_firmware() FAIL FAIL
request_firmware_direct() FAIL FAIL
request_firmware_nowait(uevent=true) FAIL FAIL
request_firmware_nowait(uevent=false) FAIL FAIL
============================================================================
After this patch:
============================================================================
CONFIG_FW_LOADER_USER_HELPER_FALLBACK=n
CONFIG_FW_LOADER_USER_HELPER=y
Most common Linux distribution setup.
API-type no-firmware-found firmware-found
----------------------------------------------------------------------
request_firmware() FAIL OK
request_firmware_direct() FAIL OK
request_firmware_nowait(uevent=true) FAIL OK
request_firmware_nowait(uevent=false) FAIL OK
============================================================================
CONFIG_FW_LOADER_USER_HELPER_FALLBACK=n
CONFIG_FW_LOADER_USER_HELPER=n
Only possible if CONFIG_DELL_RBU=n and CONFIG_LEDS_LP55XX_COMMON=n, rare.
API-type no-firmware-found firmware-found
----------------------------------------------------------------------
request_firmware() FAIL OK
request_firmware_direct() FAIL OK
request_firmware_nowait(uevent=true) FAIL OK
request_firmware_nowait(uevent=false) FAIL OK
============================================================================
CONFIG_FW_LOADER_USER_HELPER_FALLBACK=y
CONFIG_FW_LOADER_USER_HELPER=y
Google Android setup.
API-type no-firmware-found firmware-found
----------------------------------------------------------------------
request_firmware() OK OK
request_firmware_direct() FAIL OK
request_firmware_nowait(uevent=true) OK OK
request_firmware_nowait(uevent=false) OK OK
============================================================================
[0] https://bugzilla.kernel.org/show_bug.cgi?id=195477
CC: <stable@vger.kernel.org> [4.10+]
Cc: Ming Lei <ming.lei@redhat.com>
Fixes: 5b02962494 ("firmware: do not use fw_lock for fw_state protection")
Reported-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Luis R. Rodriguez <mcgrof@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Moshi USB to Ethernet Adapter internally uses a Genesys Logic hub to
connect to Realtek r8153.
The Realtek r8153 ethernet does not work on the internal hub, no-lpm quirk
can make it work.
Since another r8153 dongle at my hand does not have the issue, so add
the quirk to the Genesys Logic hub instead.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
