Instead of allocating 128 struct netdev_queue per device, use the
minimum value between 128 and the number of possible txq's, to
reduce ram usage and "tc -s -d class shod dev .." output.
This patch fixes Eric Dumazet's patch to set the TX queues to
the correct minimum.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Disabling TSO can cause the dev_watchdog timer to be triggered because
when TSO is disabled netif_tx_stop_all_queues is called. If the watchdog
timer fires while the queues are stopped and traffic has not recently been
sent on a paticular queue this is falsly identified as a hang and
ndo_tx_timeout() is called. This is ocossionally seen during testing.
This removes the netif_tx_stop_all_queues() it is not needed. The scheduler
submits skb's with dev_hard_start_xmit(), this checks if netif_needs_gso and
if so it calls dev_gso_segment. Disabling TSO will cause dev_hard_start_xmit()
to do the gso processing. However ixgbe does not use the features flags to
determine if it needs to use tso or not instead it uses skb->gso_size so
ixgbe will process these frames correctly regardless of the netdev features
flag.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Work around 82599 HW issue when HWRSC is enabled on IOMMU enabled
kernels. 82599 HW is updating the header information after setting the
descriptor to done, resulting DMA mapping/unmapping issues on IOMMU
enabled systems. To work around the issue delay unmapping of first packet
that carries the header information until end of packet is reached.
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Isolate spinlock for tx and rx to resolve double-locking.
This is potential bug while this controller does not exist on any
SMP platforms, but lockdep or rt-preempt reveals this bug.
Reported-by: Ralf Roesch <ralf.roesch@rw-gmbh.de>
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
The netif_wake_queue() is called correctly (i.e. only on !txfull
condition) from net_tx(). So Unconditional call to the
netif_wake_queue() here is wrong. This might cause calling of
start_xmit routine on txfull state and trigger tx-ring overflow.
This fix is ported from commit 662a96bd6f
("tc35815: Remove a wrong netif_wake_queue() call which triggers BUG_ON").
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hmm so actually my original patch including this bit was correct,
"list = list->next;" confused me :) - will send patch correcting that in a few.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
removed some needless checks and also corrected bug in lp486e (dmi was passed
instead of dmi->dmi_addr)
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes the bus-error reporting configurable and allows to
retrieve the CAN TX and RX bus error counters via netlink interface.
I have added support for the SJA1000. The TX and RX bus error counters
are also copied to the data fields 6..7 of error messages when state
changes are reported.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add #define pr_fmt(fmt)
Convert logging messages to pr_<level> and netdev_<level>
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert CH_<level> and CH_DBG uses to pr_<level> and netif equivalents
Remove CH_<level> and CH_DBG macro definitions
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Samll cleanup in drivers/isdn/gigaset/capi.c where own implementation of
isxdigit() has been changed to kernel native one.
Signed-off-by: Andy Shevchenko <ext-andriy.shevchenko@nokia.com>
Acked-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
Improve readability of the Gigaset driver's kernel messages by
removing a few unnecessary messages and limiting the emission
of some debug messages more narrowly.
Impact: logging
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
Copy the mechanism from ser_/usb_gigaset to avoid producing
spurious empty responses for CR/LF sequences from the device.
Add a comment in all drivers documenting that behaviour.
Correct an off by one error that might result in a one byte
buffer overflow when receiving an unexpectedly long reply.
Impact: minor bugfix
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
netif_carrier_on() and netif_carrier_off() should be called from
link status interrupt handler
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Keycodes in 248 - 254 range were reserved for special needs (scrolling)
of atkbd driver. Now that the driver has been switched to use unsigned
short keycodes instead of unsigned char we can release this range back
into pull. We keep code 255 (ATKBD_KEY_NULL) reserved since users may
have been using it to silence keys they do not care about since atkbd
silently drops scancodes mapped to this keycode.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
* 'next-devicetree' of git://git.secretlab.ca/git/linux-2.6: (41 commits)
of: remove undefined request_OF_resource & release_OF_resource
of/sparc: Remove sparc-local declaration of allnodes and devtree_lock
of: move definition of of_chosen into common code.
of: remove unused extern reference to devtree_lock
of: put default string compare and #a/s-cell values into common header
of/flattree: Don't assume HAVE_LMB
of: protect linux/of.h with CONFIG_OF
proc_devtree: fix THIS_MODULE without module.h
of: Remove old and misplaced function declarations
of/flattree: Make the kernel accept ePAPR style phandle information
of/flattree: endian-convert members of boot_param_header
of: assume big-endian properties, adding conversions where necessary
of: use __be32 for cell value accessors
of/flattree: use OF_ROOT_NODE_{SIZE,ADDR}_CELLS DEFAULT for fdt parsing
of/flattree: use callback to setup initrd from /chosen
proc_devtree: include linux/of.h
of: make set_node_proc_entry private to proc_devtree.c
of: include linux/proc_fs.h
of/flattree: merge early_init_dt_scan_memory() common code
of: add 'of_' prefix to machine_is_compatible()
...
* 'next-spi' of git://git.secretlab.ca/git/linux-2.6: (31 commits)
spi: Correct SPI clock frequency setting in spi_mpc8xxx
spi/spi_s3c64xx.c: Fix continuation line formats
spi/dw_spi: Fix dw_spi_mmio to depend on HAVE_CLK
spi/dw_spi: Allow dw_spi.c to be a module
spi/dw_spi: mmio code style fixups
Memory-mapped dw_spi driver
spi/dw_spi: fix missing export of dw_spi_remove_host
spi/dw_spi: conditional transfer mode changes
spi/dw_spi: remove conditional from 'poll_transfer'.
spi/dw_spi: fixed a spelling typo in a warning message.
spi/dw_spi: add return value to empty mrst_spi_debugfs_init()
spi/dw_spi: enable platform specific chipselect.
spi/dw_spi: add a FIFO depth detection
spi/dw_spi: fix __init/__devinit section mismatch
spi: xilinx_spi: Fix up I/O routine wrapping bogosity.
spi/spi_imx: add device information by switching pr_debug() to dev_dbg()
spi: update MSIOF includes
spi/dw_spi: refine the IRQ mode working flow
spi/dw_spi: add a missed dw_spi_remove_host() in exit sequence
spi/dw_spi: bug fix in wait_till_not_busy()
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid: (41 commits)
HID: usbhid: initialize interface pointers early enough
HID: extend mask for BUTTON usage page
HID: hid-ntrig: Single touch mode tap
HID: hid-ntrig: multitouch cleanup and fix
HID: n-trig: remove unnecessary tool switching
HID: hid-ntrig add multi input quirk and clean up
HID: usbhid: introduce timeout for stuck ctrl/out URBs
HID: magicmouse: coding style and probe failure fixes
HID: remove MODULE_VERSION from new drivers
HID: fix up Kconfig entry for MagicMouse
HID: add a device driver for the Apple Magic Mouse.
HID: Export hid_register_report
HID: Support for MosArt multitouch panel
HID: add pressure support for the Stantum multitouch panel
HID: fixed bug in single-touch emulation on the stantum panel
HID: fix typo in error message
HID: add mapping for "AL Network Chat" usage
HID: use multi input quirk for TouchPack touchscreen
HID: make full-fledged hid-bus drivers properly selectable
HID: make Wacom modesetting failures non-fatal
...
Currently, only those mem resources are validated which are already
registered at the time the first PCMCIA card is inserted. As we can
only validate resources immediately after card insert, store
"registered" mem resources in mem_db, and only upon validation move
them to mem_db_valid. When allocationg mem resources, mem_db_valid is
then preferred to mem_db.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Calling the ENAB method on Toshiba laptops results in notifications being
sent when laptop hotkeys are pressed. This patch simply calls that method
and sets up an input device if it's successful.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
The Latitude C640 has another variation of dell in its DMI vendor entry.
Add it to the whitelist in order to enjoy the sweet fruits of software
backlight toggling.
Signed-off-by: Erik Andren <erik.andren@gmail.com>
Instead of a MODULE_DEVICE_TABLE for every acpi_driver ids table, we
create a table containing all ids to export to get a module alias for
each one.
This will fix automatic loading of the driver when one of the ACPI
devices is not present (like the accelerometer, which is not present in
some models).
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@holoscopio.com>
Right now, we assume that the hardware rfkill switch on Dells toggles all
radio devices. In fact, this can be configured in the BIOS and so right
now we may mark a device as hardware killed even when it isn't. Add code
to query the devices controlled by the switch, and use this when
determining the hardware kill state of a radio.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Calls to communicate with system firmware via a SMI (using dcdbas)
need to use a buffer that has a physical address of 4GB or less.
Currently the dell-laptop driver does not guarantee this, and when the
buffer address is higher than 4GB, the address is truncated to 32 bits
and the SMI handler writes to the wrong memory address.
Signed-off-by: Stuart Hayes <stuart_hayes@dell.com>
Acked-by: Matthew Garrett <mjg@redhat.com>
The Mini family doesn't support smbios 17,11 although it reports it does.
Signed-off-by: Mario Limonciello <superm1@ubuntu.com>
Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
The "hardware" switch is tied directly to a BIOS interface that will
connect and disconnect the hardware from the bus.
If you use the software interface to request the BIOS to make these
changes, the HW switch will be in an inconsistent state and LEDs may not
reflect the state of the HW.
Signed-off-by: Mario Limonciello <Mario_Limonciello@Dell.com>
dell-laptop currently fails to clean up its platform device correctly.
Make sure that it's unregistered.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
The rfkill interface on Dells only sends a notification that the switch
has been changed via the keyboard controller. Add a filter so we can
pick these notifications up and update the rfkill state appropriately.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
This drops the support for manually groking the files in sysfs
to turn on and off the WLAN and BT for Compal laptops in favor
of platform rfkill support.
It has been combined into a single patch to not introduce regressions
in the process of simply adding rfkill support
Signed-off-by: Mario Limonciello <Mario_Limonciello@Dell.com>
Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Cc: Cezary Jackiewicz <cezary.jackiewicz@gmail.com>
The following Dell laptops are known to have been manufacturer by Compal
and are supported by the compal-laptop platform driver
- Mini 9
- Mini 10
- Mini 12
- Mini 10v
- Inspiron 11z
Signed-off-by: Mario Limonciello <Mario_Limonciello@Dell.com>
Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Cc: Cezary Jackiewicz <cezary.jackiewicz@gmail.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-for-linus: (44 commits)
Add MAINTAINERS entry for virtio_console
virtio: console: Fill ports' entire in_vq with buffers
virtio: console: Error out if we can't allocate buffers for control queue
virtio: console: Add ability to remove module
virtio: console: Ensure no memleaks in case of unused buffers
virtio: console: show error message if hvc_alloc fails for console ports
virtio: console: Add debugfs files for each port to expose debug info
virtio: console: Add ability to hot-unplug ports
virtio: console: Handle port hot-plug
virtio: console: Remove cached data on port close
virtio: console: Register with sysfs and create a 'name' attribute for ports
virtio: console: Ensure only one process can have a port open at a time
virtio: console: Add file operations to ports for open/read/write/poll
virtio: console: Associate each port with a char device
virtio: console: Prepare for writing to userspace buffers
virtio: console: Add a new MULTIPORT feature, support for generic ports
virtio: console: Introduce a send_buf function for a common path for sending data to host
virtio: console: Introduce function to hand off data from host to readers
virtio: console: Separate out find_vqs operation into a different function
virtio: console: Separate out console init into a new function
...
The ADS7846/TSC2046 touchscreen controllers can (and usually are)
connected to various regulators for power, so add regulator support.
Valid regulator will now be required, so boards without complete
regulator setup should either disable regulator framework or enable
CONFIG_REGULATOR_DUMMY.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
All of the SH clocksource drivers follow the scheme that the IRQ is setup
prior to registering the clockevent. The interrupt handler in the
clockevent cases looks to the event handler function pointer being filled
in by the registration code, permitting us to get in to situations where
asserted IRQs step in to the handler before registration has had a chance
to complete and hitting a NULL pointer deref.
In practice this is not an issue for most platforms, but some of them
with fairly special loaders (or that are chain-loading from another
kernel) may enter in to this situation. This fixes up the oops reported
by Rafael on hp6xx.
Reported-and-tested-by: Rafael Ignacio Zurita <rafaelignacio.zurita@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Mike Cui reported that his system with an NVIDIA MCP79 (aka MCP7A)
chipset stopped working with 2.6.32. The problem appears to be that
2.6.32 now enables the FPDMA auto-activate optimization in the ahci
driver. The drive works fine with this enabled on an Intel AHCI so
this appears to be a chipset bug. Since MCP79 is a fairly recent
NVIDIA chipset and we don't have any info on whether any other NVIDIA
chipsets have this issue, disable FPDMA AA optimization on all NVIDIA
AHCI controllers for now.
Should address http://bugzilla.kernel.org/show_bug.cgi?id=14922
Signed-off-by: Robert Hancock <hancockrwd@gmail.com>
While-we-investigate-issue-this-patch-looks-good-to-me-by:
Prajakta Gudadhe <pgudadhe@nvidia.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Cc: stable@kernel.org
Eddie Wai