Johannes Berg says:
====================
Quite a few more updates:
- cfg80211/mac80211:
- various security(-ish) fixes
- fix A-MSDU subframe handling
- fix multi-link element parsing
- ath10: avoid sending commands to dead device
- ath11k:
- fix WMI buffer leaks on error conditions
- fix UAF in RX MSDU coalesce path
- allow peer ID 0 on RX path (legal for mobile devices)
- reinitialize shared SRNG pointers on restart
- ath12k:
- fix 20 MHz-only parsing of EHT-MCS map
- iwlwifi:
- fix TSO segmentation explosion
- don't TX to dead device
- fix warning in WoWLAN
- fix TX rates on old devices
- disconnect on beacon loss only if also no other traffic
- fill NULL-ptr deref
- fix STEP_URM hardware access
* tag 'wireless-2026-05-21' of https://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless: (24 commits)
wifi: cfg80211: wext: validate chandef in monitor mode
wifi: mac80211: consume only present negotiated TTLM maps
wifi: wilc1000: fix dma_buffer leak on bus acquire failure
wifi: mac80211: capture fast-RX rate before mesh reuses skb->cb
wifi: mac80211: fix multi-link element inheritance
wifi: mac80211: fix MLE defragmentation
wifi: mac80211: don't override max_amsdu_subframes
wifi: mac80211: bounds-check link_id in ieee80211_ml_epcs
wifi: ath12k: fix EHT TX MCS limitation due to wrong 20 MHz-only parsing
wifi: ath11k: clear shared SRNG pointer state on restart
wifi: ath11k: fix use after free in ath11k_dp_rx_msdu_coalesce()
wifi: ath11k: fix peer resolution on rx path when peer_id=0
wifi: iwlwifi: mld: disconnect only after 6 beacons without Rx
wifi: iwlwifi: mld: don't WARN on WoWLAN suspend w/o BSS vif
wifi: iwlwifi: use correct function to read STEP_URM register
wifi: iwlwifi: mvm: fix driver-set TX rates on old devices
wifi: iwlwifi: mld: don't dereference a pointer before NULL checking it
wifi: iwlwifi: mld: stop TX during firmware restart
wifi: iwlwifi: mld: fix TSO segmentation explosion when AMSDU is disabled
wifi: ath10k: skip WMI and beacon transmission when device is wedged
...
====================
Link: https://patch.msgid.link/20260521152903.374070-3-johannes@sipsolutions.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
During SR-IOV teardown, enetc_msg_psi_free() disables the MR interrupt
before pci_disable_sriov() removes the VFs. If a VF sends a mailbox
message during this window, the PF cannot receive it, causing the VF to
timeout waiting for a reply.
Since the timeout occurs during SR-IOV teardown when the VF is about to
be removed anyway, it has no functional impact on operation. However,
more messages will be added in the future, some visible error logs may
confuse users. So fix it by calling pci_disable_sriov() first to remove
all VFs, then safely clean up the mailbox resources. This eliminates the
race window where VFs could send messages to an unresponsive PF.
Fixes: beb74ac878 ("enetc: Add vf to pf messaging support")
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Reviewed-by: Harshitha Ramamurthy <hramamurthy@google.com>
Link: https://patch.msgid.link/20260520064421.91569-10-wei.fang@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Sashiko reported a potential issue in enetc_msg_psi_init() where the IRQ
handler is registered before DMA resources are fully initialized [1].
The current initialization sequence is:
1. request_irq(enetc_msg_psi_msix) <- IRQ handler registered
2. INIT_WORK(&pf->msg_task, ...) <- work_struct initialized
3. enetc_msg_alloc_mbx() <- mailbox DMA allocated
This ordering is unsafe because if a spurious interrupt or pending
interrupt from a previous device state fires immediately after
request_irq() returns, the registered ISR enetc_msg_psi_msix() will
execute and unconditionally call:
schedule_work(&pf->msg_task)
At this point, pf->msg_task has not been initialized by INIT_WORK(), so
the work_struct contains garbage values in its internal linked list
pointers (work_struct->entry). Passing an uninitialized work_struct to
schedule_work() could corrupt the kernel's workqueue linked lists,
potentially leading to:
- Kernel panic in __queue_work()
- Memory corruption in workqueue data structures
- System deadlock or undefined behavior
Additionally, even if the work_struct was initialized, the mailbox DMA
buffers (pf->rxmsg[]) may not yet be allocated when the work handler
enetc_msg_task() runs, resulting in NULL pointer dereference.
Fix by reordering the initialization sequence to ensure all resources are
properly initialized before the interrupt handler can execute:
1. enetc_msg_alloc_mbx() <- Allocate all mailboxes
2. INIT_WORK(&pf->msg_task, ...) <- Initialize work first
3. request_irq(enetc_msg_psi_msix) <- Register IRQ last
4. Configure hardware & enable MR interrupts
This guarantees that when enetc_msg_psi_msix() runs:
- pf->msg_task is properly initialized (safe for schedule_work)
- pf->rxmsg[] buffers are allocated (safe for work handler access)
- Hardware is configured appropriately
As the inverse of enetc_msg_psi_init(), enetc_msg_psi_free() also has
similar problems. For example, if a pending interrupt fires between
enetc_msg_free_mbx() and free_irq(), the ISR enetc_msg_psi_msix() may
schedule the work handler again via schedule_work(), which could then
access already-freed DMA buffers (pf->rxmsg[]), leading to use-after-free
and potential memory corruption.
Therefore, the order of enetc_msg_psi_free() is adjusted:
1. enetc_msg_disable_mr_int() <- Stop new interrupts first
2. free_irq() <- Ensure no IRQ handler can run
3. cancel_work_sync() <- Wait for any pending work
4. enetc_msg_disable_mr_int() <- Re-disable in case work
re-enabled it
5. enetc_msg_free_mbx() <- Safe to free DMA buffers now
Link: https://sashiko.dev/#/patchset/20260511080805.2052495-1-wei.fang%40nxp.com#1
Fixes: beb74ac878 ("enetc: Add vf to pf messaging support")
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Reviewed-by: Harshitha Ramamurthy <hramamurthy@google.com>
Link: https://patch.msgid.link/20260520064421.91569-9-wei.fang@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The enetc_msg_task() function has several issues that need to be addressed:
1. Unbounded loop causing potential DoS:
enetc_msg_task() processes VF-to-PF mailbox messages in an unbounded
for(;;) loop that keeps polling ENETC_PSIMSGRR until no MR bits are set.
A malicious guest VM can exploit this by continuously sending messages at
a high rate - immediately sending a new message as soon as the PF
acknowledges the previous one. Since the worker thread never yields or
enforces a processing budget, the mr_mask check frequently evaluates to
non-zero, causing the PF to spin indefinitely and starving other tasks.
Fix this by replacing the unbounded loop with a single snapshot read at
task entry. The task processes only the VFs whose MR bits were set at
that point, then re-enables message interrupts before returning. This
bounds work per invocation to at most num_vfs iterations. No messages are
lost because the message interrupt is disabled in enetc_msg_psi_msix()
before scheduling enetc_msg_task(), so any new messages arriving during
processing will trigger a fresh interrupt once re-enabled, scheduling
another task invocation.
2. Write order of ENETC_PSIIDR and ENETC_PSIMSGRR:
Both ENETC_PSIIDR and ENETC_PSIMSGRR contain MR bits indicating messages
have been received from VSIs, but only ENETC_PSIIDR trigger the CPU
interrupt. Previously, ENETC_PSIMSGRR was written before ENETC_PSIIDR.
Writing ENETC_PSIMSGRR returns the message code to the VSI in its upper
16 bits, signaling to the VF that message processing is complete and it
may send the next message. If the VF sends a new message before
ENETC_PSIIDR is written, the subsequent w1c write to ENETC_PSIIDR would
inadvertently clear the MR bit set by the new message, causing the
interrupt to be lost and the new message to go unprocessed.
Therefore, write ENETC_PSIIDR first to clear the interrupt source, then
write ENETC_PSIMSGRR to acknowledge the message to the VSI.
3. Check both ENETC_PSIMSGRR and ENETC_PSIIDR for mr_status:
The write order change above introduces a potential race: if a VF sends
a new message in the window between the ENETC_PSIIDR w1c and the
ENETC_PSIMSGRR w1c, the ENETC_PSIMSGRR MR bit for the new message may
not be set. If mr_status was derived solely from ENETC_PSIMSGRR, this
message would never be detected despite ENETC_PSIIDR retaining its MR
bit, leading to an unacknowledged interrupt storm.
Fix this by computing mr_status as the union of both ENETC_PSIMSGRR and
ENETC_PSIIDR MR bits, ensuring all pending messages are detected
regardless of which register reflects the new message state.
Additionally, rename the per-register MR macros (ENETC_PSI*_MR_MASK,
ENETC_PSI*_MR) to register-agnostic names (ENETC_PSIMR_MASK,
ENETC_PSIMR_BIT) since the MR bit layout is shared across ENETC_PSIMSGRR,
ENETC_PSIIER, and ENETC_PSIIDR. Make the mask macro dynamic based on
the actual number of active VFs rather than hardcoded.
Fixes: beb74ac878 ("enetc: Add vf to pf messaging support")
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Link: https://patch.msgid.link/20260520064421.91569-8-wei.fang@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The teardown sequence in enetc_msg_psi_free() frees the DMA buffer before
clearing the device's DMA address registers. If a VF sends a message or a
pending DMA transfer completes within this window, the hardware will
perform a DMA write into the kernel memory that has already been returned
to the allocator.
The result is silent memory corruption that can affect arbitrary kernel
data structures. Therefore, clear the DMA address registers before the
DMA buffer is freed.
Fixes: beb74ac878 ("enetc: Add vf to pf messaging support")
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Reviewed-by: Harshitha Ramamurthy <hramamurthy@google.com>
Link: https://patch.msgid.link/20260520064421.91569-7-wei.fang@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Sashiko reported a potential race condition between the VF message
handler and administrative VF MAC configuration from the host [1].
The VF message handler (enetc_msg_pf_set_vf_primary_mac_addr) runs
asynchronously in a workqueue context and accesses vf_state->flags
without any locking. Concurrently, the host can administratively
change the VF MAC address via enetc_pf_set_vf_mac(), which executes
under RTNL lock and modifies both vf_state->flags and hardware
registers.
This creates two race windows:
1) TOCTOU race on vf_state->flags: The check of ENETC_VF_FLAG_PF_SET_MAC
and subsequent MAC programming are not atomic, allowing the flag state
to change between check and use.
2) Torn MAC address writes: Hardware MAC programming requires multiple
non-atomic register writes (__raw_writel for lower 32 bits and
__raw_writew for upper 16 bits). Concurrent updates from VF mailbox
and PF admin paths can interleave these operations, resulting in a
corrupted MAC address being programmed into the hardware.
Fix by introducing a per-VF mutex to serialize access to vf_state and
hardware MAC register updates. Both enetc_pf_set_vf_mac() and
enetc_msg_pf_set_vf_primary_mac_addr() now acquire this lock before
accessing vf_state->flags or programming the MAC address, ensuring
atomic read-modify-write sequences and preventing register write
interleaving.
Link: https://sashiko.dev/#/patchset/20260511080805.2052495-1-wei.fang%40nxp.com#1
Fixes: beb74ac878 ("enetc: Add vf to pf messaging support")
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Reviewed-by: Harshitha Ramamurthy <hramamurthy@google.com>
Link: https://patch.msgid.link/20260520064421.91569-6-wei.fang@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Sashiko reported that the PF driver accepts arbitrary MAC address from
from VF mailbox messages without proper validation, creating a security
vulnerability [1].
In enetc_msg_pf_set_vf_primary_mac_addr(), the MAC address is extracted
directly from the message buffer (cmd->mac.sa_data) and programmed into
hardware via pf->ops->set_si_primary_mac() without any validity checks.
A malicious VF can configure a multicast, broadcast, or all-zero MAC
address. Therefore, a validation to check the MAC address provided by VF
is required.
However, simply checking the MAC address is not enough, because it also
has the potential TOCTOU race [2]: The code reads the MAC address from
the DMA buffer to validate it via is_valid_ether_addr(), if validation
passes, reads the same DMA buffer a second time when calling
enetc_pf_set_primary_mac_addr() to program the hardware. A malicious VF
can exploit this window by overwriting the MAC address in the DMA buffer
between the validation check and the hardware programming, bypassing the
validation entirely.
Therefore, allocate a local buffer in enetc_msg_handle_rxmsg() and copy
the message content from the DMA buffer via memcpy() before processing.
This ensures the PF operates on a stable snapshot that the VF cannot
modify.
Link: https://sashiko.dev/#/patchset/20260511080805.2052495-1-wei.fang%40nxp.com#1
Link: https://sashiko.dev/#/patchset/20260513103021.2190593-1-wei.fang%40nxp.com#2
Fixes: beb74ac878 ("enetc: Add vf to pf messaging support")
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Reviewed-by: Harshitha Ramamurthy <hramamurthy@google.com>
Link: https://patch.msgid.link/20260520064421.91569-5-wei.fang@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In enetc_pf_probe(), when the memory allocation for pf->vf_state fails,
the code jumps to the error handling label but the variable 'err' is not
assigned an appropriate error code beforehand. This causes the function
to return 0 (success) on an allocation failure path, misleading the
caller into thinking the probe succeeded. So set err to -ENOMEM before
jumping to the error handling label when the allocation for pf->vf_state
returns NULL.
Fixes: e15c5506dd ("net: enetc: allocate vf_state during PF probes")
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Reviewed-by: Harshitha Ramamurthy <hramamurthy@google.com>
Link: https://patch.msgid.link/20260520064421.91569-3-wei.fang@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There are two cases where VFs receive an incorrect success status from
the PF mailbox message handler, misleading them into believing their
requests have been fulfilled:
In enetc_msg_handle_rxmsg(), *status is pre-initialized to
ENETC_MSG_CMD_STATUS_OK. When an unsupported command type is received,
the default case only logs an error without updating *status, so it
remains as ENETC_MSG_CMD_STATUS_OK.
In enetc_msg_pf_set_vf_primary_mac_addr(), when the PF has already
assigned a MAC address for the VF (ENETC_VF_FLAG_PF_SET_MAC is set),
the function rejects the request but returns ENETC_MSG_CMD_STATUS_OK
instead of ENETC_MSG_CMD_STATUS_FAIL.
Therefore, correct the status value for the two cases mentioned above.
Fixes: beb74ac878 ("enetc: Add vf to pf messaging support")
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Reviewed-by: Harshitha Ramamurthy <hramamurthy@google.com>
Link: https://patch.msgid.link/20260520064421.91569-2-wei.fang@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Setting RBUF_EEE_EN | RBUF_PM_EN in RBUF_ENERGY_CTRL breaks the RX
path on GENET hardware once MAC EEE becomes active. RX traffic stops
flowing while the link stays up and the usual descriptor/RX error
counters remain quiet. In that state the MAC still accepts frames
(rbuf_ovflow_cnt keeps climbing) but RBUF no longer forwards them to
DMA, so rx_packets is no longer incremented at the netdev level. On
some boards the corruption ends up as a paging fault in
skb_release_data via bcmgenet_rx_poll on an LPI exit.
Reproduced on Pi 4B (BCM2711 + BCM54213PE) and confirmed by Florian
Fainelli on an internal Broadcom 4908-family board with the same crash
signature. RBUF_PM_EN is not publicly documented.
This shows up more often now that phy_support_eee() enables EEE by
default, but it also affects older kernels as soon as TX LPI is
turned on via ethtool, so it is not specific to recent changes.
Always clear RBUF_EEE_EN | RBUF_PM_EN in bcmgenet_eee_enable_set so
the bits stay off across resets. UMAC and TBUF setup is left alone so
TX-side EEE keeps working.
Link: https://github.com/raspberrypi/linux/issues/7304
Fixes: 6ef398ea60 ("net: bcmgenet: add EEE support")
Cc: stable@vger.kernel.org
Signed-off-by: Nicolai Buchwitz <nb@tipi-net.de>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20260520184320.652053-1-nb@tipi-net.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Update the driver for our current coding style according to output from
`checkpatch.pl' and manual code review, where no change to binary code
results, as indicated by `objdump -dr'. Exceptions are as follows:
- incomplete reverse xmas tree in set_multicast_list(), as that would
change binary output,
- referring el3_start_xmit() verbatim rather than via `__func__' with
pr_debug(), likewise,
- a bunch of pr_cont() calls, likewise,
- a long udelay() call in el3_netdev_set_ecmd() made under a spinlock,
likewise plus it's not eligible for conversion to a sleep in the first
place,
- a blank line at the start of a block in el3_interrupt(), to improve
readability where the first statement would otherwise visually merge
with the controlling expression of the enclosing `while' statement.
These issues are benign and depending on circumstances may be adressed
with suitable code refactoring later on.
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Link: https://patch.msgid.link/alpine.DEB.2.21.2605201208280.1450@angie.orcam.me.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The transceiver type is held in bits 15:14 of the Address Configuration
Register, with the values of 0b00, 0b01, and 0b11 denoting TP, AUI, and
BNC types respectively. Therefore switching from BNC to AUI requires
bits to be cleared before setting bit 14 or the setting won't change.
NB this has always been wrong ever since this code was added in 2.5.42.
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Link: https://patch.msgid.link/alpine.DEB.2.21.2605201205160.1450@angie.orcam.me.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The driver passes fw_version directly to devlink_info_version_stored_put()
without ensuring null-termination. While current firmware null-terminates
these strings, the driver should not rely on this behavior. Add explicit
null-termination to prevent potential issues if firmware behavior changes.
Fixes: 45d76f4929 ("pds_core: set up device and adminq")
Signed-off-by: Nikhil P. Rao <nikhil.rao@amd.com>
Link: https://patch.msgid.link/20260520205842.1486718-1-nikhil.rao@amd.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In the SIOCGIFHWADDR path, tap_ioctl() copies 16 bytes of an
uninitialised on-stack struct sockaddr_storage to userspace via
ifr_hwaddr, but netif_get_mac_address() only writes sa_family and
dev->addr_len (6 for Ethernet) bytes, leaving sa_data[6..13] uninitialised.
Those 8 trailing bytes leak kernel stack contents; SIOCGIFHWADDR on a
macvtap chardev returns kernel .text and direct-map pointers, defeating
KASLR.
Initialise ss at declaration.
Fixes: 3b23a32a63 ("net: fix dev_ifsioc_locked() race condition")
Reported-by: Xiang Mei <xmei5@asu.edu>
Signed-off-by: Weiming Shi <bestswngs@gmail.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Link: https://patch.msgid.link/20260520075736.3415676-3-bestswngs@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If one of the later PF or VF CID bitmap allocations fails,
qed_cid_map_alloc() jumps to cid_map_fail and frees the previously
allocated CID bitmaps before returning an error. qed_cxt_tables_alloc()
then calls qed_cxt_mngr_free(), which invokes qed_cid_map_free()
again.
Fix this by setting each CID bitmap pointer to NULL after bitmap_free()
to avoid double free.
The bug was first flagged by an experimental analysis tool we are
developing for kernel memory-management bugs while analyzing
v6.13-rc1. The tool is still under development and is not yet publicly
available. Manual inspection confirms that the bug is still
present in v7.1-rc3.
Runtime reproduction was not attempted because exercising the failing
allocation path requires device-specific setup.
Fixes: fe56b9e6a8 ("qed: Add module with basic common support")
Cc: stable@vger.kernel.org
Signed-off-by: Zilin Guan <zilin@seu.edu.cn>
Signed-off-by: Dawei Feng <dawei.feng@seu.edu.cn>
Link: https://patch.msgid.link/20260520070323.2762379-1-dawei.feng@seu.edu.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In mana_hwc_rx_event_handler(), rx_req_idx is derived from
sge->address in DMA-coherent memory. In Confidential VMs
(SEV-SNP/TDX), this memory is shared unencrypted and HW can modify
WQE contents at any time. No bounds check exists on rx_req_idx,
which can lead to an out-of-bounds access into reqs[].
Add bounds check on rx_req_idx in mana_hwc_rx_event_handler() before
using it to index the reqs[] array.
Fixes: ca9c54d2d6 ("net: mana: Add a driver for Microsoft Azure Network Adapter (MANA)")
Signed-off-by: Aditya Garg <gargaditya@linux.microsoft.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Link: https://patch.msgid.link/20260520051553.857120-1-gargaditya@linux.microsoft.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When installing the allmulticast NPC rule, rvu_npc_install_allmulti_entry()
should skip LBK and SDP VFs (only CGX PF/VF may add the entry). The
code combined is_lbk_vf() and is_sdp_vf() with logical AND, which is
never true for a single pcifunc, so the intended early return never ran.
Use logical OR instead.
Cc: Geetha sowjanya <gakula@marvell.com>
Fixes: ae703539f4 ("octeontx2-af: Cleanup loopback device checks")
Signed-off-by: Ratheesh Kannoth <rkannoth@marvell.com>
Link: https://patch.msgid.link/20260520043036.1523798-1-rkannoth@marvell.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Validate rx-internal-delay-ps and tx-internal-delay-ps against the
hardware capabilities of the EIC7700 MAC.
The programmable RGMII delay supports 20 ps steps and a maximum value of
2540 ps. The driver previously accepted arbitrary values and silently
truncated unsupported settings when converting them to hardware units.
As a result, invalid device tree values could lead to unexpected delay
programming and incorrect RGMII timing.
Reject delay values that are not multiples of 20 ps or exceed the
supported hardware range.
Fixes: ea77dbbdbc ("net: stmmac: add Eswin EIC7700 glue driver")
Signed-off-by: Zhi Li <lizhi2@eswincomputing.com>
Link: https://patch.msgid.link/20260518022214.507-1-lizhi2@eswincomputing.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The EIC7700 MAC implements programmable RGMII delay adjustment with a
granularity of 20 ps per hardware step.
The driver previously converted rx-internal-delay-ps and
tx-internal-delay-ps values using a 100 ps step size, resulting in
incorrect delay programming.
Update the conversion to use the correct 20 ps granularity so the
programmed delay matches the values described in the device tree.
Fixes: ea77dbbdbc ("net: stmmac: add Eswin EIC7700 glue driver")
Signed-off-by: Zhi Li <lizhi2@eswincomputing.com>
Link: https://patch.msgid.link/20260518022156.484-1-lizhi2@eswincomputing.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Clear the TXD and RXD delay control registers during EIC7700 DWMAC
initialization.
These registers may retain values programmed by the bootloader. If left
unchanged, residual delays can alter the effective RGMII timing seen by
the MAC and override the configuration described by the device tree.
This may violate the expected RGMII timing model and can cause link
instability or prevent the Ethernet controller from operating correctly.
Explicitly clearing these registers ensures that the MAC delay settings
are determined solely by the kernel configuration.
The corresponding register offsets are optional, and the registers are
only cleared when the offsets are provided in the device tree.
Fixes: ea77dbbdbc ("net: stmmac: add Eswin EIC7700 glue driver")
Signed-off-by: Zhi Li <lizhi2@eswincomputing.com>
Link: https://patch.msgid.link/20260518022137.464-1-lizhi2@eswincomputing.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Fix the initialization ordering of the HSP CSR configuration in the
EIC7700 DWMAC glue driver.
The HSP CSR registers control MAC-side RGMII delay behavior and must
only be accessed after the corresponding clocks are enabled. The
previous implementation could trigger register access before clock
enablement, leading to undefined behavior depending on boot state.
Move the HSP CSR configuration into the post-clock-enable initialization
path to ensure all register accesses occur under valid clock domains.
This change ensures deterministic initialization and prevents
clock-dependent register access failures during probe or resume.
Fixes: ea77dbbdbc ("net: stmmac: add Eswin EIC7700 glue driver")
Signed-off-by: Zhi Li <lizhi2@eswincomputing.com>
Link: https://patch.msgid.link/20260518022055.444-1-lizhi2@eswincomputing.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
mlx5e_xfrm_add_state() handles acquire-flow temporary SAs by allocating
software state and skipping hardware offload setup.
That path jumps to the common success label before taking the eswitch mode
block. After tunnel-mode validation was moved earlier, the common success
label unconditionally calls mlx5_eswitch_unblock_mode(). For acquire SAs,
this decrements esw->offloads.num_block_mode without a matching increment.
Return directly after installing the acquire SA offload handle, so only the
paths that successfully called mlx5_eswitch_block_mode() call the matching
unblock.
Fixes: 22239eb258 ("net/mlx5e: Prevent tunnel reformat when tunnel mode not allowed")
Signed-off-by: Prathamesh Deshpande <prathameshdeshpande7@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/20260510225903.13184-1-prathameshdeshpande7@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jeff Johnson says:
==================
ath.git update for v7.1-rc5
ath10k:
- avoid sending any commands to firmware when it is wedged
ath11k:
- fix WMI buffer leaks on error conditions
- fix UAF in RX MSDU coalesce path
- allow peer ID 0 on RX path (legal for mobile devices)
- reinitialize shared SRNG pointers on restart
ath12k:
- fix 20 MHz-only parsing of EHT-MCS map
==================
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
wilc_wlan_firmware_download() allocates dma_buffer with kmalloc() at
the top of the function and uses a 'fail:' label to free it via
kfree(dma_buffer) on error.
All later error paths correctly use 'goto fail' to route through this
cleanup. However, the early failure path after the first acquire_bus()
call uses a bare 'return ret;', which leaks dma_buffer whenever the bus
acquire fails.
Replace the early return with goto fail so the existing cleanup path
runs.
Found via a custom Coccinelle semantic patch hunting for kmalloc'd
locals leaked on early-return error paths in driver firmware-download
code.
Fixes: 1241c5650f ("wifi: wilc1000: Fill in missing error handling")
Signed-off-by: Shitalkumar Gandhi <shitalkumar.gandhi@cambiumnetworks.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20260511042732.998311-1-shitalkumar.gandhi@cambiumnetworks.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
debugfs_lookup() returns a dentry with an elevated reference count that
must be released with dput(). The current code discards the returned
dentry without calling dput(), causing a reference leak on every
firmware reset recovery.
Additionally, when CONFIG_DEBUG_FS is disabled, debugfs_lookup()
returns ERR_PTR(-ENODEV), not NULL. The current check passes for error
pointers and would call dput() on an invalid pointer, causing a crash.
Fixes: bc90fbe0c3 ("pds_core: Rework teardown/setup flow to be more common")
Signed-off-by: Nikhil P. Rao <nikhil.rao@amd.com>
Link: https://patch.msgid.link/20260515212907.998028-3-nikhil.rao@amd.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fix two cases where pdsc_devcmd_wait() returns stale success from
the completion register instead of an error:
1. FW crash: If firmware stops running, the wait loop breaks early with
running=false. The condition "if ((!done || timeout) && running)" is
false, so error handling is bypassed and stale status is returned.
Check !running first and return -ENXIO.
2. Timeout: If a command times out, err is set to -ETIMEDOUT but then
overwritten by pdsc_err_to_errno(status) which reads stale status.
Return -ETIMEDOUT immediately after cleaning up.
Both errors now propagate to pdsc_devcmd_locked() which queues
health_work for recovery.
Fixes: 45d76f4929 ("pds_core: set up device and adminq")
Signed-off-by: Nikhil P. Rao <nikhil.rao@amd.com>
Link: https://patch.msgid.link/20260515212907.998028-1-nikhil.rao@amd.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
phy_advertise_eee_all() copies supported_eee into advertising_eee
unconditionally, overwriting any filtering applied during phy_probe()
based on DT eee-broken-* properties or driver-populated
eee_disabled_modes. genphy_c45_ethtool_set_eee() calls this helper
when user space passes an empty advertisement, undoing the filtering.
Apply the same eee_disabled_modes mask in phy_advertise_eee_all() so
the filtering survives the copy, matching the pattern in phy_probe()
and phy_support_eee().
Fixes: b64691274f ("net: phy: add helper phy_advertise_eee_all")
Signed-off-by: Nicolai Buchwitz <nb@tipi-net.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20260518-devel-phy-support-eee-fix-v2-2-05b52626fa68@tipi-net.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
phy_support_eee() copies supported_eee into advertising_eee
unconditionally, overwriting any filtering applied during phy_probe()
based on DT eee-broken-* properties or driver-populated
eee_disabled_modes. MAC drivers that call phy_support_eee() after
probe (e.g. bcmgenet, fec, lan743x, lan78xx, r8169) then cause the PHY
to advertise EEE for modes the user marked as broken.
The symptom is that ethtool --show-eee on the local interface reports
"not supported" (supported & ~eee_disabled_modes is empty) while the
link partner sees EEE negotiated and active.
phy_probe() already filters advertising_eee via eee_disabled_modes
after calling of_set_phy_eee_broken(). Apply the same mask in
phy_support_eee() so the filtering survives the copy.
Fixes: 49168d1980 ("net: phy: Add phy_support_eee() indicating MAC support EEE")
Signed-off-by: Nicolai Buchwitz <nb@tipi-net.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20260518-devel-phy-support-eee-fix-v2-1-05b52626fa68@tipi-net.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
genphy_c45_an_config_eee_aneg() writes the EEE advertisement to the
auto-negotiation device's MMD register space (MDIO_MMD_AN, register
MDIO_AN_EEE_ADV). These registers are read by the link partner only
during auto-negotiation, so writing them while autoneg is disabled
cannot influence the link. On some PHYs (e.g. Broadcom BCM54213PE)
the write nevertheless reaches the chip and disturbs the receive
datapath.
Concretely, running
ethtool -s eth0 speed 100 duplex full autoneg off
ethtool --set-eee eth0 eee off
leaves eth0 with TX working and RX completely silent on a
Raspberry Pi 4 / CM4 board (bcmgenet + BCM54213PE in rgmii-rxid).
Switching back to autoneg recovers the link.
Prior to commit f26a29a038 ("net: phy: ensure that genphy_c45_an_config_eee_aneg() sees new value of phydev->eee_cfg.eee_enabled"),
the disable path was effectively a no-op because the helper read
the stale eee_cfg.eee_enabled, so the underlying PHY behavior never
surfaced.
Bisected on rpi-6.12.y between commits 83943264 (good) and
effcbc88 (bad) to f26a29a038.
Fixes: f26a29a038 ("net: phy: ensure that genphy_c45_an_config_eee_aneg() sees new value of phydev->eee_cfg.eee_enabled")
Cc: stable@vger.kernel.org
Signed-off-by: Nerijus Bendžiūnas <nerijus.bendziunas@gmail.com>
Reviewed-by: Nicolai Buchwitz <nb@tipi-net.de>
Tested-by: Nicolai Buchwitz <nb@tipi-net.de>
Link: https://patch.msgid.link/20260516150251.879680-1-nerijus.bendziunas@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
otx2_pool_aq_init() frees pool->stack when mailbox sync or retry
allocation fails, but leaves the pointer unchanged. Later,
otx2_sq_aura_pool_init() unwinds the partial setup through
otx2_aura_pool_free(), which frees pool->stack again. The CN20K-specific
cn20k_pool_aq_init() implementation has the same bug in
its corresponding error path.
Set pool->stack to NULL immediately after the local free so the shared
cleanup path does not free the same stack again while cleaning up
partially initialized pool state.
The bug was first flagged by an experimental analysis tool we are
developing for kernel memory-management bugs while analyzing
v6.13-rc1. The tool is still under development and is not yet publicly
available. Manual inspection confirms that the bug is still present in
v7.1-rc3.
Runtime validation was not performed because reproducing this path
requires OcteonTX2/CN20K hardware.
Fixes: caa2da34fd ("octeontx2-pf: Initialize and config queues")
Fixes: d322fbd172 ("octeontx2-pf: Initialize cn20k specific aura and pool contexts")
Cc: stable@vger.kernel.org
Signed-off-by: Zilin Guan <zilin@seu.edu.cn>
Signed-off-by: Dawei Feng <dawei.feng@seu.edu.cn>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20260515151826.1005397-1-dawei.feng@seu.edu.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
of_count_phandle_with_args() returns the count on success and a negative
errno on failure, including -ENOENT when the "pairsets" property is
absent. The existing comparison in of_load_pse_pis() checks against
ENOENT (positive 2) instead of -ENOENT, so the branch is taken for any
error return: legitimate DTs that omit "pairsets" trigger a spurious
"wrong number of pairsets" error and probe fails with -EINVAL.
Compare against -ENOENT so a missing "pairsets" property is correctly
treated as "this PI has no pairsets, continue".
Fixes: 9be9567a7c ("net: pse-pd: Add support for PSE PIs")
Cc: stable@vger.kernel.org
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://patch.msgid.link/20260515143103.1721888-1-jelonek.jonas@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Antonio Quartulli says:
====================
Included fixes:
* fix TCP selftest failures by reducing number of attempted pings
* fix RCU ptr deref outside of RCU read section
* fix UAF in case of TCP peer failed to be added to hashtable
* fix race condition between iface teardown and new peer being added
* ensure dstats are updated with BH disabled to avoid concurrency
* tag 'ovpn-net-20260514' of https://github.com/OpenVPN/ovpn-net-next:
ovpn: disable BHs when updating device stats
ovpn: fix race between deleting interface and adding new peer
ovpn: respect peer refcount in CMD_NEW_PEER error path
ovpn: tcp - use cached peer pointer in ovpn_tcp_close()
selftests: ovpn: reduce remaining ping flood counts
====================
Link: https://patch.msgid.link/20260514231544.795993-1-antonio@openvpn.net
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
In mana_hwc_rx_event_handler(), resp->response.hwc_msg_id is read from
DMA-coherent memory and bounds-checked, then mana_hwc_handle_resp()
re-reads the same field from the same DMA buffer for test_bit() and
pointer arithmetic.
DMA-coherent memory is mapped uncacheable on x86 and is shared,
unencrypted, in Confidential VMs (SEV-SNP/TDX), so each load goes
directly to host-visible memory. A H/W can modify the value
between the check and the use, bypassing the bounds validation.
Fix this by reading hwc_msg_id exactly once using READ_ONCE() into a
stack-local variable in mana_hwc_rx_event_handler(), and passing the
validated value as a parameter to mana_hwc_handle_resp().
Fixes: ca9c54d2d6 ("net: mana: Add a driver for Microsoft Azure Network Adapter (MANA)")
Signed-off-by: Erni Sri Satya Vennela <ernis@linux.microsoft.com>
Link: https://patch.msgid.link/20260514194156.466823-1-ernis@linux.microsoft.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
With bridge VLAN filtering enabled on a port configured as untagged
member of the bridge PVID, ingress untagged frames do not reach the
corresponding bridge VLAN upper interface (br-lan.<vid>). ARP and
similar traffic is visible on the physical port but not delivered
to the VLAN sub-interface.
The MT7530/MT7531 forwards frames to the CPU port with the user
port's PVID tag applied even when the frame ingressed untagged on
the wire, because the CPU port is set to MT7530_VLAN_EG_CONSISTENT
and is a tagged member of the VLAN entry created for the bridge
VLAN. The DSA core then sees a hwaccel-tagged frame whose VID
matches the port's PVID, which the bridge does not treat as the
untagged-on-the-wire frame that the user expects.
Set ds->untag_vlan_aware_bridge_pvid in the mt7530 and mt7531
setup paths so the DSA core strips that hwaccel tag in software
when the parsed VID matches the bridge port's PVID, restoring the
on-the-wire frame as the bridge expects to see it.
Link: https://github.com/openwrt/openwrt/issues/18576
Fixes: 83163f7dca ("net: dsa: mediatek: add VLAN support for MT7530")
Signed-off-by: Edward Parker <edward@topnotchit.com>
[daniel@makrotopia.org: improve commit message]
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Link: https://patch.msgid.link/85d25ea1b26d3c907f815649f2e0bde6560282a3.1778766629.git.daniel@makrotopia.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
After a VLAN-aware bridge is destroyed, creating any VLAN-unaware
bridge loses all connectivity. The VID 0 VLAN table entry used by
VLAN-unaware ports in FALLBACK mode gets corrupted during VLAN-aware
operation: mt7530_hw_vlan_add() overwrites its EG_CON flag with
VTAG_EN and bridge teardown removes ports from its PORT_MEM.
The cleanup code that should restore it never runs because the current
port's dp->vlan_filtering flag is still true when checked (DSA updates
it only after the driver callback returns). Even when restored, the
deferred VLAN deletion events from the switchdev workqueue can corrupt
VID 0 again after the restoration.
Skip the current port in the all_user_ports_removed check, call
mt7530_setup_vlan0() to restore the VID 0 entry, and protect VID 0
from being modified by bridge VLAN operations in port_vlan_add and
port_vlan_del since it is managed exclusively by mt7530_setup_vlan0().
Remove the CPU port PCR and PVC register writes which were clobbering
PORT_VLAN mode and VLAN_ATTR with wrong values.
Fixes: 83163f7dca ("net: dsa: mediatek: add VLAN support for MT7530")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Link: https://patch.msgid.link/da8bdaf08b2427a9057e6cb33e26d41f8a8d5000.1778766629.git.daniel@makrotopia.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The BPC, RGAC1 and RGAC2 registers control the handling of link-local
frames with reserved MAC DAs (01:80:C2:00:00:0x). These frames are
correctly trapped to the CPU port, but the egress VLAN tag attribute was
set to MT7530_VLAN_EG_UNTAGGED which causes the switch to strip any
VLAN tags from trapped frames before they reach the CPU.
This causes VLAN-tagged link-local frames (STP BPDUs, LLDP, PTP Peer
Delay Requests) to arrive at the CPU without their VLAN tag, so they
are delivered to the base network interface instead of the VLAN
sub-interface. The DSA local_termination selftest confirms this: all
link-local protocol tests on VLAN upper interfaces fail.
Set the EG_TAG attribute to MT7530_VLAN_EG_DISABLED (system default)
so that the switch does not modify VLAN tags in trapped frames. This
way VLAN-tagged frames retain their original tag and are delivered to
the correct VLAN sub-interface, matching the behavior of non-trapped
frames which pass through without VLAN tag modification.
Fixes: 69ddba9d17 ("net: dsa: mt7530: fix handling of all link-local frames")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Acked-by: Chester A. Unal <chester.a.unal@arinc9.com>
Link: https://patch.msgid.link/891e0cd34db2a5fe20ceb73283a81fb5f71427ca.1778766629.git.daniel@makrotopia.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The DSA forwarding selftests bridge_vlan_aware.sh and
bridge_vlan_unaware.sh configure the bridge with ageing_time set to
LOW_AGEING_TIME (1000 centiseconds, i.e. 10 seconds) and then run
learning_test() in lib.sh, which expects a learned FDB entry to be
removed after ageing_time + 10 seconds. On MT7530/MT7531 the entry
persisted past the deadline and the "Found FDB record when should
not" assertion failed.
With msecs=10000, the algorithm in mt7530_set_ageing_time() finds
AGE_CNT=0 and AGE_UNIT=9 as the first exact match (starting the
search from tmp_age_count=0). The per-entry aging counter is
initialized to AGE_CNT when a MAC address is learned, so with
AGE_CNT=0 new entries start with a counter value of 0, which the
hardware treats as "already aged" and never removes, effectively
disabling aging.
Fix this by starting the search from tmp_age_count=1 to ensure
entries always have a non-zero initial aging counter. For a
10-second ageing time this yields AGE_CNT=1 and AGE_UNIT=4 instead:
the timer ticks every 5 seconds and entries are removed after 2
ticks.
Starting the search at AGE_CNT=1 raises the minimum representable
ageing time from 1 to 2 seconds. Without bounds, a stale ageing_time
of 1 second would now make the loop fall through without setting
age_count and age_unit, leaving them uninitialized when written to
the MT7530_AAC hardware register. Set ds->ageing_time_min and
ds->ageing_time_max so the DSA core validates the range before the
callback is invoked, and drop the now-redundant range check from
mt7530_set_ageing_time().
Fixes: ea6d5c924e ("net: dsa: mt7530: support setting ageing time")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Link: https://patch.msgid.link/7788ded12dc07b1bce329ec35fa70f4b45f3f9b7.1778766629.git.daniel@makrotopia.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
When igc_fpe_init_tx_descriptor() fails, no one takes care of an
allocated skb, leaking it. [1]
Use dev_kfree_skb_any() on failure.
Tested on an I226 adapter with the following command, while injecting
faults in igc_fpe_init_tx_descriptor() to trigger the error path.
# ethtool --set-mm $DEV verify-enabled on tx-enabled on pmac-enabled on
[1]
unreferenced object 0xffff888113c6cdc0 (size 224):
...
backtrace (crc be3d3fda):
kmem_cache_alloc_node_noprof+0x3b1/0x410
__alloc_skb+0xde/0x830
igc_fpe_xmit_smd_frame.isra.0+0xad/0x1b0
igc_fpe_send_mpacket+0x37/0x90
ethtool_mmsv_verify_timer+0x15e/0x300
Cc: stable@vger.kernel.org
Fixes: 5422570c00 ("igc: add support for frame preemption verification")
Signed-off-by: Kohei Enju <kohei@enjuk.jp>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Faizal Rahim <faizal.abdul.rahim@linux.intel.com>
Tested-by: Avigail Dahan <avigailx.dahan@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://patch.msgid.link/20260515182419.1597859-10-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
ixgbevf_clean_rx_irq() prunes frames whose source MAC matches the VF's
own address (VEPA multicast workaround) by freeing the skb and
continuing to the next descriptor:
dev_kfree_skb_irq(skb);
continue;
The skb pointer is declared outside the while loop and persists across
iterations. Because the continue skips the "skb = NULL" reset at the
bottom of the loop, the next iteration enters the "else if (skb)" path
and calls ixgbevf_add_rx_frag() on the freed skb, dereferencing
skb_shinfo(skb)->nr_frags - a use-after-free in NAPI softirq context.
The sibling driver iavf already handles this correctly by nulling the
pointer before continuing. Apply the same pattern here.
I do not have ixgbevf hardware; the bug was found by static analysis
(scan_drop_continue_loops.py + semgrep drop_continue_in_loop, multi-tool
corroboration with the highest score in the scan). The UAF was confirmed
under KASAN by loading a test module that reproduces the exact code
pattern (alloc skb, kfree_skb, then read skb_shinfo(skb)->nr_frags):
BUG: KASAN: slab-use-after-free in ixgbevf_uaf_test_init+0x100/0x1000
Read of size 8 at addr 000000006163ae78 by task insmod/30
freed 208-byte region [000000006163adc0, 000000006163ae90)
QEMU emulates igb (82576) but not ixgbe (82599), and the igbvf VF
driver does not include the VEPA source pruning path, so a full
end-to-end reproduction with emulated hardware was not possible.
Fixes: bad17234ba ("ixgbevf: Change receive model to use double buffered page based receives")
Cc: stable@vger.kernel.org
Signed-off-by: Michael Bommarito <michael.bommarito@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://patch.msgid.link/20260515182419.1597859-8-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When ethtool -L changes queue counts, ice_vsi_recfg_qs() closes and
rebuilds the VSI, reallocating Rx rings. The newly allocated rings have
ptp_rx cleared, so RX hardware timestamps are no longer attached to skb
until hwtstamp configuration is applied again.
Restore timestamp mode after ice_vsi_open() in the queue reconfiguration
path, matching reset/rebuild behavior and ensuring newly rebuilt Rx rings
have PTP RX timestamping re-enabled.
Testing hints:
- run ptp4l application in client synchronization mode:
ptp4l -i ethX -m -s
- run PTP traffic
- change queue number on ethX netdev interface:
ethtool -L ethX combined new_queue_size
- observe ptp4l output
- expected result: no "received DELAY_REQ without timestamp" messages
Fixes: 77a781155a ("ice: enable receive hardware timestamping")
Cc: stable@vger.kernel.org
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Grzegorz Nitka <grzegorz.nitka@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Alexander Nowlin <alexander.nowlin@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://patch.msgid.link/20260515182419.1597859-7-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
For E825 2xNAC configurations, PTP semaphore operations must hit the
primary NAC register block so both sides coordinate on the same lock.
Commit e2193f9f9e ("ice: enable timesync operation on 2xNAC E825
devices") updated other primary-only PTP register accesses to
use the primary NAC on non-primary functions, but left ice_ptp_lock()
and ice_ptp_unlock() operating on the local NAC. As a result, secondary
NAC PTP paths can take a different semaphore than the primary side.
Select the primary hardware in ice_ptp_lock() and ice_ptp_unlock() when
the current function is not primary, keeping semaphore operations
symmetric and consistent with the rest of the 2xNAC PTP register access
path.
Fixes: e2193f9f9e ("ice: enable timesync operation on 2xNAC E825 devices")
Reviewed-by: Arkadiusz Kubalewski <Arkadiusz.kubalewski@intel.com>
Signed-off-by: Grzegorz Nitka <grzegorz.nitka@intel.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Tested-by: Alexander Nowlin <alexander.nowlin@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://patch.msgid.link/20260515182419.1597859-6-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
ice_start_phy_timer_eth56g() programs TIMETUS registers and issues
INIT_INCVAL without holding the global PTP semaphore.
This allows concurrent PTP command paths to interleave with PHY timer
start, which can make the sequence fail and leave timer initialization
inconsistent.
Take the PTP lock around TIMETUS registers programming and INIT_INCVAL
command execution, and make sure the lock is released on all error paths.
Keep the subsequent sync step outside of this critical section, since
ice_sync_phy_timer_eth56g() takes the same semaphore internally.
Fixes: 7cab44f1c3 ("ice: Introduce ETH56G PHY model for E825C products")
Reviewed-by: Arkadiusz Kubalewski <Arkadiusz.kubalewski@intel.com>
Signed-off-by: Grzegorz Nitka <grzegorz.nitka@intel.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Tested-by: Alexander Nowlin <alexander.nowlin@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://patch.msgid.link/20260515182419.1597859-5-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
