This patch is to add 3 constants SCTP_FUTURE_ASSOC,
SCTP_CURRENT_ASSOC and SCTP_ALL_ASSOC for reserved
assoc_ids, as defined in rfc6458#section-7.2.
And add the process for them when doing lookup and
inserting in sctp_id2assoc and sctp_assoc_set_id.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add notification call for devlink port param set, register and unregister
functions.
Add devlink_port_param_value_changed() function to enable the driver notify
devlink on value change. Driver should use this function after value was
changed on any configuration mode part to driverinit.
v7->v8:
Order devlink_port_param_value_changed() definitions followed by
devlink_param_value_changed()
Cc: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann says:
====================
pull-request: bpf-next 2019-01-29
The following pull-request contains BPF updates for your *net-next* tree.
The main changes are:
1) Teach verifier dead code removal, this also allows for optimizing /
removing conditional branches around dead code and to shrink the
resulting image. Code store constrained architectures like nfp would
have hard time doing this at JIT level, from Jakub.
2) Add JMP32 instructions to BPF ISA in order to allow for optimizing
code generation for 32-bit sub-registers. Evaluation shows that this
can result in code reduction of ~5-20% compared to 64 bit-only code
generation. Also add implementation for most JITs, from Jiong.
3) Add support for __int128 types in BTF which is also needed for
vmlinux's BTF conversion to work, from Yonghong.
4) Add a new command to bpftool in order to dump a list of BPF-related
parameters from the system or for a specific network device e.g. in
terms of available prog/map types or helper functions, from Quentin.
5) Add AF_XDP sock_diag interface for querying sockets from user
space which provides information about the RX/TX/fill/completion
rings, umem, memory usage etc, from Björn.
6) Add skb context access for skb_shared_info->gso_segs field, from Eric.
7) Add support for testing flow dissector BPF programs by extending
existing BPF_PROG_TEST_RUN infrastructure, from Stanislav.
8) Split BPF kselftest's test_verifier into various subgroups of tests
in order better deal with merge conflicts in this area, from Jakub.
9) Add support for queue/stack manipulations in bpftool, from Stanislav.
10) Document BTF, from Yonghong.
11) Dump supported ELF section names in libbpf on program load
failure, from Taeung.
12) Silence a false positive compiler warning in verifier's BTF
handling, from Peter.
13) Fix help string in bpftool's feature probing, from Prashant.
14) Remove duplicate includes in BPF kselftests, from Yue.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter/IPVS updates for net-next
The following patchset contains Netfilter/IPVS updates for your net-next tree:
1) Introduce a hashtable to speed up object lookups, from Florian Westphal.
2) Make direct calls to built-in extension, also from Florian.
3) Call helper before confirming the conntrack as it used to be originally,
from Florian.
4) Call request_module() to autoload br_netfilter when physdev is used
to relax the dependency, also from Florian.
5) Allow to insert rules at a given position ID that is internal to the
batch, from Phil Sutter.
6) Several patches to replace conntrack indirections by direct calls,
and to reduce modularization, from Florian. This also includes
several follow up patches to deal with minor fallout from this
rework.
7) Use RCU from conntrack gre helper, from Florian.
8) GRE conntrack module becomes built-in into nf_conntrack, from Florian.
9) Replace nf_ct_invert_tuplepr() by calls to nf_ct_invert_tuple(),
from Florian.
10) Unify sysctl handling at the core of nf_conntrack, from Florian.
11) Provide modparam to register conntrack hooks.
12) Allow to match on the interface kind string, from wenxu.
13) Remove several exported symbols, not required anymore now after
a bit of de-modulatization work has been done, from Florian.
14) Remove built-in map support in the hash extension, this can be
done with the existing userspace infrastructure, from laura.
15) Remove indirection to calculate checksums in IPVS, from Matteo Croce.
16) Use call wrappers for indirection in IPVS, also from Matteo.
17) Remove superfluous __percpu parameter in nft_counter, patch from
Luc Van Oostenryck.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull input fixes from Dmitry Torokhov:
"A fixup for the input_event fix for y2038 Sparc64, and couple other
minor fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: input_event - fix the CONFIG_SPARC64 mixup
Input: olpc_apsp - assign priv->dev earlier
Input: uinput - fix undefined behavior in uinput_validate_absinfo()
Input: raspberrypi-ts - fix link error
Input: xpad - add support for SteelSeries Stratus Duo
Input: input_event - provide override for sparc64
The new eBPF instruction class JMP32 uses the reserved class number 0x6.
Kernel BPF ISA documentation updated accordingly.
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Jiong Wang <jiong.wang@netronome.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Pull block fixes from Jens Axboe:
"A collection of fixes for this release. This contains:
- Silence sparse rightfully complaining about non-static wbt
functions (Bart)
- Fixes for the zoned comments/ioctl documentation (Damien)
- direct-io fix that's been lingering for a while (Ernesto)
- cgroup writeback fix (Tejun)
- Set of NVMe patches for nvme-rdma/tcp (Sagi, Hannes, Raju)
- Block recursion tracking fix (Ming)
- Fix debugfs command flag naming for a few flags (Jianchao)"
* tag 'for-linus-20190125' of git://git.kernel.dk/linux-block:
block: Fix comment typo
uapi: fix ioctl documentation
blk-wbt: Declare local functions static
blk-mq: fix the cmd_flag_name array
nvme-multipath: drop optimization for static ANA group IDs
nvmet-rdma: fix null dereference under heavy load
nvme-rdma: rework queue maps handling
nvme-tcp: fix timeout handler
nvme-rdma: fix timeout handler
writeback: synchronize sync(2) against cgroup writeback membership switches
block: cover another queue enter recursion via BIO_QUEUE_ENTERED
direct-io: allow direct writes to empty inodes
Pull char/misc driver fixes from Greg KH:
"Here are some small char and misc driver fixes to resolve some
reported issues, as well as a number of binderfs fixups that were
found after auditing the filesystem code by Al Viro. As binderfs
hasn't been in a previous release yet, it's good to get these in now
before the first users show up.
All of these have been in linux-next for a bit with no reported
issues"
* tag 'char-misc-5.0-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (26 commits)
i3c: master: Fix an error checking typo in 'cdns_i3c_master_probe()'
binderfs: switch from d_add() to d_instantiate()
binderfs: drop lock in binderfs_binder_ctl_create
binderfs: kill_litter_super() before cleanup
binderfs: rework binderfs_binder_device_create()
binderfs: rework binderfs_fill_super()
binderfs: prevent renaming the control dentry
binderfs: remove outdated comment
binderfs: use __u32 for device numbers
binderfs: use correct include guards in header
misc: pvpanic: fix warning implicit declaration
char/mwave: fix potential Spectre v1 vulnerability
misc: ibmvsm: Fix potential NULL pointer dereference
binderfs: fix error return code in binderfs_fill_super()
mei: me: add denverton innovation engine device IDs
mei: me: mark LBG devices as having dma support
mei: dma: silent the reject message
binderfs: handle !CONFIG_IPC_NS builds
binderfs: reserve devices for initial mount
binderfs: rename header to binderfs.h
...
This patch adds the sock_diag interface for querying sockets from user
space. Tools like iproute2 ss(8) can use this interface to list open
AF_XDP sockets.
The user-space ABI is defined in linux/xdp_diag.h and includes netlink
request and response structs. The request can query sockets and the
response contains socket information about the rings, umems, inode and
more.
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
The description of the BLKGETNRZONES zoned block device ioctl was not
added as a comment together with this ioctl definition in commit
65e4e3eee8 ("block: Introduce BLKGETNRZONES ioctl"). Add its
description here.
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This adds the ability to read gso_segs from a BPF program.
v3: Use BPF_REG_AX instead of BPF_REG_TMP for the temporary register,
as suggested by Martin.
v2: refined Eddie Hao patch to address Alexei feedback.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Eddie Hao <eddieh@google.com>
Cc: Martin KaFai Lau <kafai@fb.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Arnd Bergmann pointed out that CONFIG_* cannot be used in a uapi header.
Override with an equivalent conditional.
Fixes: 2e746942eb ("Input: input_event - provide override for sparc64")
Fixes: 152194fe9c ("Input: extend usable life of event timestamps to 2106 on 32 bit systems")
Signed-off-by: Deepa Dinamani <deepa.kernel@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
When multiple multicast routers are present in a broadcast domain then
only one of them will be detectable via IGMP/MLD query snooping. The
multicast router with the lowest IP address will become the selected and
active querier while all other multicast routers will then refrain from
sending queries.
To detect such rather silent multicast routers, too, RFC4286
("Multicast Router Discovery") provides a standardized protocol to
detect multicast routers for multicast snooping switches.
This patch implements the necessary MRD Advertisement message parsing
and after successful processing adds such routers to the internal
multicast router list.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: David S. Miller <davem@davemloft.net>
Next to snooping IGMP/MLD queries RFC4541, section 2.1.1.a) recommends
to snoop multicast router advertisements to detect multicast routers.
Multicast router advertisements are sent to an "all-snoopers"
multicast address. To be able to receive them reliably, we need to
join this group.
Otherwise other snooping switches might refrain from forwarding these
advertisements to us.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for extended statistics (xstats) call to the
bonding. The first user would be the 3ad code which counts the following
events:
- LACPDU Rx/Tx
- LACPDU unknown type Rx
- LACPDU illegal Rx
- Marker Rx/Tx
- Marker response Rx/Tx
- Marker unknown type Rx
All of these are exported via netlink as separate attributes to be
easily extensible as we plan to add more in the future.
Similar to how the bridge and other xstats exports, the structure
inside is:
[ IFLA_STATS_LINK_XSTATS ]
-> [ LINK_XSTATS_TYPE_BOND ]
-> [ BOND_XSTATS_3AD ]
-> [ 3ad stats attributes ]
With this structure it's easy to add more stat types later.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We allow more then 255 binderfs binder devices to be created since there
are workloads that require more than that. If we use __u8 we'll overflow
after 255. So let's use a __u32.
Note that there's no released kernel with binderfs out there so this is
not a regression.
Signed-off-by: Christian Brauner <christian@brauner.io>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When we switched over from binder_ctl.h to binderfs.h we forgot to change
the include guards. It's minor but it's obviously correct.
Signed-off-by: Christian Brauner <christian@brauner.io>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull networking fixes from David Miller:
1) Fix endless loop in nf_tables, from Phil Sutter.
2) Fix cross namespace ip6_gre tunnel hash list corruption, from
Olivier Matz.
3) Don't be too strict in phy_start_aneg() otherwise we might not allow
restarting auto negotiation. From Heiner Kallweit.
4) Fix various KMSAN uninitialized value cases in tipc, from Ying Xue.
5) Memory leak in act_tunnel_key, from Davide Caratti.
6) Handle chip errata of mv88e6390 PHY, from Andrew Lunn.
7) Remove linear SKB assumption in fou/fou6, from Eric Dumazet.
8) Missing udplite rehash callbacks, from Alexey Kodanev.
9) Log dirty pages properly in vhost, from Jason Wang.
10) Use consume_skb() in neigh_probe() as this is a normal free not a
drop, from Yang Wei. Likewise in macvlan_process_broadcast().
11) Missing device_del() in mdiobus_register() error paths, from Thomas
Petazzoni.
12) Fix checksum handling of short packets in mlx5, from Cong Wang.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (96 commits)
bpf: in __bpf_redirect_no_mac pull mac only if present
virtio_net: bulk free tx skbs
net: phy: phy driver features are mandatory
isdn: avm: Fix string plus integer warning from Clang
net/mlx5e: Fix cb_ident duplicate in indirect block register
net/mlx5e: Fix wrong (zero) TX drop counter indication for representor
net/mlx5e: Fix wrong error code return on FEC query failure
net/mlx5e: Force CHECKSUM_UNNECESSARY for short ethernet frames
tools: bpftool: Cleanup license mess
bpf: fix inner map masking to prevent oob under speculation
bpf: pull in pkt_sched.h header for tooling to fix bpftool build
selftests: forwarding: Add a test case for externally learned FDB entries
selftests: mlxsw: Test FDB offload indication
mlxsw: spectrum_switchdev: Do not treat static FDB entries as sticky
net: bridge: Mark FDB entries that were added by user as such
mlxsw: spectrum_fid: Update dummy FID index
mlxsw: pci: Return error on PCI reset timeout
mlxsw: pci: Increase PCI SW reset timeout
mlxsw: pci: Ring CQ's doorbell before RDQ's
MAINTAINERS: update email addresses of liquidio driver maintainers
...
Similar to u32 filter, it is useful to know how many times
we reach each basic filter and how many times we pass the
ematch attached to it.
Sample output:
filter protocol arp pref 49152 basic chain 0
filter protocol arp pref 49152 basic chain 0 handle 0x1 (rule hit 3 success 3)
action order 1: gact action pass
random type none pass val 0
index 1 ref 1 bind 1 installed 81 sec used 4 sec
Action statistics:
Sent 126 bytes 3 pkt (dropped 0, overlimits 0 requeues 0)
backlog 0b 0p requeues 0
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add devlink health dump commands, in order to run an dump operation
over a specific reporter.
The supported operations are dump_get in order to get last saved
dump (if not exist, dump now) and dump_clear to clear last saved
dump.
It is expected from driver's callback for diagnose command to fill it
via the buffer descriptors API. Devlink will parse it and convert it to
netlink nla API in order to pass it to the user.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add devlink health diagnose command, in order to run a diagnose
operation over a specific reporter.
It is expected from driver's callback for diagnose command to fill it
via the buffer descriptors API. Devlink will parse it and convert it to
netlink nla API in order to pass it to the user.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add devlink health recover command to the uapi, in order to allow the user
to execute a recover operation over a specific reporter.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add devlink health set command, in order to set configuration parameters
for a specific reporter.
Supported parameters are:
- graceful_period: Time interval between auto recoveries (in msec)
- auto_recover: Determines if the devlink shall execute recover upon
receiving error for the reporter
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add devlink health get command to provide reporter/s data for user space.
Add the ability to get data per reporter or dump data from all available
reporters.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Devlink health buffer is a mechanism to pass descriptors between drivers
and devlink. The API allows the driver to add objects, object pair,
value array (nested attributes), value and name.
Driver can use this API to fill the buffers in a format which can be
translated by the devlink to the netlink message.
In order to fulfill it, an internal buffer descriptor is defined. This
will hold the data and metadata per each attribute and by used to pass
actual commands to the netlink.
This mechanism will be later used in devlink health for dump and diagnose
data store by the drivers.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Although matchall always matches packets, however, it still
relies on a protocol match first. So it is still useful to have
such a counter for matchall. Of course, unlike u32, every time
we hit a matchall filter, it is always a success, so we don't
have to distinguish them.
Sample output:
filter protocol 802.1Q pref 100 matchall chain 0
filter protocol 802.1Q pref 100 matchall chain 0 handle 0x1
not_in_hw (rule hit 10)
action order 1: vlan pop continue
index 1 ref 1 bind 1 installed 40 sec used 1 sec
Action statistics:
Sent 836 bytes 10 pkt (dropped 0, overlimits 0 requeues 0)
backlog 0b 0p requeues 0
Reported-by: Martin Olsson <martin.olsson+netdev@sentorsecurity.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A better way to implement this from userspace has been found without
specific code in the kernel side, revert this.
Fixes: b9ccc07e3f ("netfilter: nft_hash: add map lookups for hashing operations")
Signed-off-by: Laura Garcia Liebana <nevola@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
In the ip_rcv the skb goes through the PREROUTING hook first, then kicks
in vrf device and go through the same hook again. When conntrack dnat
works with vrf, there will be some conflict with rules because the
packet goes through the hook twice with different nf status.
ip link add user1 type vrf table 1
ip link add user2 type vrf table 2
ip l set dev tun1 master user1
ip l set dev tun2 master user2
nft add table firewall
nft add chain firewall zones { type filter hook prerouting priority - 300 \; }
nft add rule firewall zones counter ct zone set iif map { "tun1" : 1, "tun2" : 2 }
nft add chain firewall rule-1000-ingress
nft add rule firewall rule-1000-ingress ct zone 1 tcp dport 22 ct state new counter accept
nft add rule firewall rule-1000-ingress counter drop
nft add chain firewall rule-1000-egress
nft add rule firewall rule-1000-egress tcp dport 22 ct state new counter drop
nft add rule firewall rule-1000-egress counter accept
nft add chain firewall rules-all { type filter hook prerouting priority - 150 \; }
nft add rule firewall rules-all ip daddr vmap { "2.2.2.11" : jump rule-1000-ingress }
nft add rule firewall rules-all ct zone vmap { 1 : jump rule-1000-egress }
nft add rule firewall dnat-all ct zone vmap { 1 : jump dnat-1000 }
nft add rule firewall dnat-1000 ip daddr 2.2.2.11 counter dnat to 10.0.0.7
For a package with ip daddr 2.2.2.11 and tcp dport 22, first time accept in the
rule-1000-ingress and dnat to 10.0.0.7. Then second time the packet goto the wrong
chain rule-1000-egress which leads the packet drop
With this patch, userspace can add the 'don't re-do entire ruleset for
vrf' policy itself via:
nft add rule firewall rules-all meta iifkind "vrf" counter accept
Signed-off-by: wenxu <wenxu@ucloud.cn>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
To allow for a batch to contain rules in arbitrary ordering, introduce
NFTA_RULE_POSITION_ID attribute which works just like NFTA_RULE_POSITION
but contains the ID of another rule within the same batch. This helps
iptables-nft-restore handling dumps with mixed insert/append commands
correctly.
Note that NFTA_RULE_POSITION takes precedence over
NFTA_RULE_POSITION_ID, so if the former is present, the latter is
ignored.
Signed-off-by: Phil Sutter <phil@nwl.cc>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Pull rdma fixes frfom Jason Gunthorpe:
"Not much so far. We have the usual batch of bugs and two fixes to code
merged this cycle:
- Restore valgrind support for the ioctl verbs interface merged this
window, and fix a missed error code on an error path from that
conversion
- A user reported crash on obsolete mthca hardware
- pvrdma was using the wrong command opcode toward the hypervisor
- NULL pointer crash regression when dumping rdma-cm over netlink
- Be conservative about exposing the global rkey"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma:
RDMA/uverbs: Mark ioctl responses with UVERBS_ATTR_F_VALID_OUTPUT
RDMA/mthca: Clear QP objects during their allocation
RDMA/vmw_pvrdma: Return the correct opcode when creating WR
RDMA/cma: Add cm_id restrack resource based on kernel or user cm_id type
RDMA/nldev: Don't expose unsafe global rkey to regular user
RDMA/uverbs: Fix post send success return value in case of error
This introduces a new generic SOL_SOCKET-level socket option called
SO_BINDTOIFINDEX. It behaves similar to SO_BINDTODEVICE, but takes a
network interface index as argument, rather than the network interface
name.
User-space often refers to network-interfaces via their index, but has
to temporarily resolve it to a name for a call into SO_BINDTODEVICE.
This might pose problems when the network-device is renamed
asynchronously by other parts of the system. When this happens, the
SO_BINDTODEVICE might either fail, or worse, it might bind to the wrong
device.
In most cases user-space only ever operates on devices which they
either manage themselves, or otherwise have a guarantee that the device
name will not change (e.g., devices that are UP cannot be renamed).
However, particularly in libraries this guarantee is non-obvious and it
would be nice if that race-condition would simply not exist. It would
make it easier for those libraries to operate even in situations where
the device-name might change under the hood.
A real use-case that we recently hit is trying to start the network
stack early in the initrd but make it survive into the real system.
Existing distributions rename network-interfaces during the transition
from initrd into the real system. This, obviously, cannot affect
devices that are up and running (unless you also consider moving them
between network-namespaces). However, the network manager now has to
make sure its management engine for dormant devices will not run in
parallel to these renames. Particularly, when you offload operations
like DHCP into separate processes, these might setup their sockets
early, and thus have to resolve the device-name possibly running into
this race-condition.
By avoiding a call to resolve the device-name, we no longer depend on
the name and can run network setup of dormant devices in parallel to
the transition off the initrd. The SO_BINDTOIFINDEX ioctl plugs this
race.
Reviewed-by: Tom Gundersen <teg@jklm.no>
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 65cab850f0 ("net: Allow class-e address assignment via ifconfig
ioctl") modified the IN_BADCLASS macro a bit, but unfortunatly one too
many '(' characters were added to the line, making any code that used
it, not build properly.
Also, the macro now compares an unsigned with a signed value, which
isn't ok, so fix that up by making both types match properly.
Reported-by: Christopher Ferris <cferris@google.com>
Fixes: 65cab850f0 ("net: Allow class-e address assignment via ifconfig ioctl")
Cc: Dave Taht <dave.taht@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Fix regression in multi-SKB responses to RTM_GETADDR, from Arthur
Gautier.
2) Fix ipv6 frag parsing in openvswitch, from Yi-Hung Wei.
3) Unbounded recursion in ipv4 and ipv6 GUE tunnels, from Stefano
Brivio.
4) Use after free in hns driver, from Yonglong Liu.
5) icmp6_send() needs to handle the case of NULL skb, from Eric
Dumazet.
6) Missing rcu read lock in __inet6_bind() when operating on mapped
addresses, from David Ahern.
7) Memory leak in tipc-nl_compat_publ_dump(), from Gustavo A. R. Silva.
8) Fix PHY vs r8169 module loading ordering issues, from Heiner
Kallweit.
9) Fix bridge vlan memory leak, from Ido Schimmel.
10) Dev refcount leak in AF_PACKET, from Jason Gunthorpe.
11) Infoleak in ipv6_local_error(), flow label isn't completely
initialized. From Eric Dumazet.
12) Handle mv88e6390 errata, from Andrew Lunn.
13) Making vhost/vsock CID hashing consistent, from Zha Bin.
14) Fix lack of UMH cleanup when it unexpectedly exits, from Taehee Yoo.
15) Bridge forwarding must clear skb->tstamp, from Paolo Abeni.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (87 commits)
bnxt_en: Fix context memory allocation.
bnxt_en: Fix ring checking logic on 57500 chips.
mISDN: hfcsusb: Use struct_size() in kzalloc()
net: clear skb->tstamp in bridge forwarding path
net: bpfilter: disallow to remove bpfilter module while being used
net: bpfilter: restart bpfilter_umh when error occurred
net: bpfilter: use cleanup callback to release umh_info
umh: add exit routine for UMH process
isdn: i4l: isdn_tty: Fix some concurrency double-free bugs
vhost/vsock: fix vhost vsock cid hashing inconsistent
net: stmmac: Prevent RX starvation in stmmac_napi_poll()
net: stmmac: Fix the logic of checking if RX Watchdog must be enabled
net: stmmac: Check if CBS is supported before configuring
net: stmmac: dwxgmac2: Only clear interrupts that are active
net: stmmac: Fix PCI module removal leak
tools/bpf: fix bpftool map dump with bitfields
tools/bpf: test btf bitfield with >=256 struct member offset
bpf: fix bpffs bitfield pretty print
net: ethernet: mediatek: fix warning in phy_start_aneg
tcp: change txhash on SYN-data timeout
...
The usec part of the timeval is defined as
__kernel_suseconds_t tv_usec; /* microseconds */
Arnd noticed that sparc64 is the only architecture that defines
__kernel_suseconds_t as int rather than long.
This breaks the current y2038 fix for kernel as we only access and define
the timeval struct for non-kernel use cases. But, this was hidden by an
another typo in the use of __KERNEL__ qualifier.
Fix the typo, and provide an override for sparc64.
Fixes: 152194fe9c ("Input: extend usable life of event timestamps to 2106 on 32 bit systems")
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Deepa Dinamani <deepa.kernel@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
It doesn't make sense to call the header binder_ctl.h when its sole
existence is tied to binderfs. So give it a sensible name. Users will far
more easily remember binderfs.h than binder_ctl.h.
Signed-off-by: Christian Brauner <christian.brauner@ubuntu.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ioctl command is read/write (or just read, if the fact that user space
writes n_samples field is ignored).
Signed-off-by: Eugene Syromiatnikov <esyr@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is sort of a mix between a new feature and a bug fix. I've managed
to screw up merging this patch set a handful of times but I think it's
OK this time around. The main new feature here is audit support for
RISC-V, with some fixes to audit-related bugs that cropped up along the
way:
* The addition of NR_syscalls into unistd.h, which is necessary for
CONFIG_FTRACE_SYSCALLS.
* The definition of CREATE_TRACE_POINTS so
__tracepoint_sys_{enter,exit} get defined.
* A fix for trace_sys_exit() so we can enable
CONFIG_HAVE_SYSCALL_TRACEPOINTS.
On RISC-V (riscv) audit is supported through generic lib/audit.c.
The patch adds required arch specific definitions.
Signed-off-by: David Abdurachmanov <david.abdurachmanov@gmail.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Pull more Kbuild updates from Masahiro Yamada:
- improve boolinit.cocci and use_after_iter.cocci semantic patches
- fix alignment for kallsyms
- move 'asm goto' compiler test to Kconfig and clean up jump_label
CONFIG option
- generate asm-generic wrappers automatically if arch does not
implement mandatory UAPI headers
- remove redundant generic-y defines
- misc cleanups
* tag 'kbuild-v4.21-3' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
kconfig: rename generated .*conf-cfg to *conf-cfg
kbuild: remove unnecessary stubs for archheader and archscripts
kbuild: use assignment instead of define ... endef for filechk_* rules
arch: remove redundant UAPI generic-y defines
kbuild: generate asm-generic wrappers if mandatory headers are missing
arch: remove stale comments "UAPI Header export list"
riscv: remove redundant kernel-space generic-y
kbuild: change filechk to surround the given command with { }
kbuild: remove redundant target cleaning on failure
kbuild: clean up rule_dtc_dt_yaml
kbuild: remove UIMAGE_IN and UIMAGE_OUT
jump_label: move 'asm goto' support test to Kconfig
kallsyms: lower alignment on ARM
scripts: coccinelle: boolinit: drop warnings on named constants
scripts: coccinelle: check for redeclaration
kconfig: remove unused "file" field of yylval union
nds32: remove redundant kernel-space generic-y
nios2: remove unneeded HAS_DMA define
Pull fscrypt updates from Ted Ts'o:
"Add Adiantum support for fscrypt"
* tag 'fscrypt_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/fscrypt:
fscrypt: add Adiantum support
Add support for the Adiantum encryption mode to fscrypt. Adiantum is a
tweakable, length-preserving encryption mode with security provably
reducible to that of XChaCha12 and AES-256, subject to a security bound.
It's also a true wide-block mode, unlike XTS. See the paper
"Adiantum: length-preserving encryption for entry-level processors"
(https://eprint.iacr.org/2018/720.pdf) for more details. Also see
commit 059c2a4d8e ("crypto: adiantum - add Adiantum support").
On sufficiently long messages, Adiantum's bottlenecks are XChaCha12 and
the NH hash function. These algorithms are fast even on processors
without dedicated crypto instructions. Adiantum makes it feasible to
enable storage encryption on low-end mobile devices that lack AES
instructions; currently such devices are unencrypted. On ARM Cortex-A7,
on 4096-byte messages Adiantum encryption is about 4 times faster than
AES-256-XTS encryption; decryption is about 5 times faster.
In fscrypt, Adiantum is suitable for encrypting both file contents and
names. With filenames, it fixes a known weakness: when two filenames in
a directory share a common prefix of >= 16 bytes, with CTS-CBC their
encrypted filenames share a common prefix too, leaking information.
Adiantum does not have this problem.
Since Adiantum also accepts long tweaks (IVs), it's also safe to use the
master key directly for Adiantum encryption rather than deriving
per-file keys, provided that the per-file nonce is included in the IVs
and the master key isn't used for any other encryption mode. This
configuration saves memory and improves performance. A new fscrypt
policy flag is added to allow users to opt-in to this configuration.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Pull fbdev updates from Bartlomiej Zolnierkiewicz:
"This time the pull request is really small.
The most notable changes are fixing fbcon to not cause crash on
unregister_framebuffer() operation when there is more than one
framebuffer, adding config option to center the bootup logo and making
FB_BACKLIGHT config option tristate (which in turn uncovered incorrect
FB_BACKLIGHT usage by DRM's nouveau driver).
Summary:
- fix fbcon to not cause crash on unregister_framebuffer() when there
is more than one framebuffer (Noralf Trønnes)
- improve support for small rotated displays (Peter Rosin)
- fix probe failure handling in udlfb driver (Dan Carpenter)
- add config option to center the bootup logo (Peter Rosin)
- make FB_BACKLIGHT config option tristate (Rob Clark)
- remove superfluous HAS_DMA dependency for goldfishfb driver (Geert
Uytterhoeven)
- misc fixes (Alexey Khoroshilov, YueHaibing, Colin Ian King, Lubomir
Rintel)
- misc cleanups (Yangtao Li, Wen Yang)
also there is DRM's nouveau driver fix for wrong FB_BACKLIGHT config
option usage (FB_BACKLIGHT is for internal fbdev subsystem use only)"
* tag 'fbdev-v4.21' of git://github.com/bzolnier/linux:
drm/nouveau: fix incorrect FB_BACKLIGHT usage in Kconfig
fbdev: fbcon: Fix unregister crash when more than one framebuffer
fbdev: Remove depends on HAS_DMA in case of platform dependency
pxa168fb: trivial typo fix
fbdev: fsl-diu: remove redundant null check on cmap
fbdev: omap2: omapfb: convert to DEFINE_SHOW_ATTRIBUTE
fbdev: uvesafb: fix spelling mistake "memoery" -> "memory"
fbdev: fbmem: add config option to center the bootup logo
fbdev: fbmem: make fb_show_logo_line return the end instead of the height
video: fbdev: pxafb: Fix "WARNING: invalid free of devm_ allocated data"
fbdev: fbmem: behave better with small rotated displays and many CPUs
video: clps711x-fb: release disp device node in probe()
fbdev: make FB_BACKLIGHT a tristate
udlfb: fix some inconsistent NULL checking
Pull HID updates from Jiri Kosina:
- high-resolution scrolling support that gracefully handles differences
between MS and Logitech implementations in HW, from Peter Hutterer
and Harry Cutts
- MSI IRQ support for intel-ish driver, from Song Hongyan
- support for new hardware (Cougar 700K, Odys Winbook 13, ASUS FX503VD,
ASUS T101HA) from Daniel M. Lambea, Hans de Goede and Aleix Roca
Nonell
- other small assorted fixups
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/hid/hid: (22 commits)
HID: i2c-hid: Add Odys Winbook 13 to descriptor override
HID: lenovo: Add checks to fix of_led_classdev_register
HID: intel-ish-hid: add MSI interrupt support
HID: debug: Change to use DEFINE_SHOW_ATTRIBUTE macro
HID: doc: fix wrong data structure reference for UHID_OUTPUT
HID: intel-ish-hid: fixes incorrect error handling
HID: asus: Add support for the ASUS T101HA keyboard dock
HID: logitech: Use LDJ_DEVICE macro for existing Logitech mice
HID: logitech: Enable high-resolution scrolling on Logitech mice
HID: logitech: Add function to enable HID++ 1.0 "scrolling acceleration"
HID: logitech-hidpp: fix typo, hiddpp to hidpp
HID: input: use the Resolution Multiplier for high-resolution scrolling
HID: core: process the Resolution Multiplier
HID: core: store the collections as a basic tree
Input: add `REL_WHEEL_HI_RES` and `REL_HWHEEL_HI_RES`
HID: input: support Microsoft wireless radio control hotkey
HID: use macros in IS_INPUT_APPLICATION
HID: asus: Add support for the ASUS FX503VD laptop
HID: asus: Add event handler to catch unmapped Asus Vendor UsagePage codes
HID: cougar: Add support for Cougar 700K Gaming Keyboard
...
