Before commit bca84a7b93 ("PM: sleep: Use DPM_FLAG_SMART_SUSPEND
conditionally") the runtime PM status of the device in intel_resume()
had always been RPM_ACTIVE because setting DPM_FLAG_SMART_SUSPEND had
caused the core to call pm_runtime_set_active() for that device during
the "noirq" resume phase. For this reason, the pm_runtime_suspended()
check in intel_resume() had never triggered and the code depending on
it had never run. That had not caused any observable functional issues
to appear, so effectively the code in question had never been needed.
After commit bca84a7b93 the core does not call pm_runtime_set_active()
for all devices with DPM_FLAG_SMART_SUSPEND set any more and the code
depending on the pm_runtime_suspended() check in intel_resume() runs if
the device is runtime-suspended prior to a system-wide suspend
transition. Unfortunately, when it runs, it breaks things due to the
attempt to runtime-resume bus->dev which most likely is not ready for a
runtime resume at that point.
It also does other more-or-less questionable things. Namely, it
calls pm_runtime_idle() for a device with a nonzero runtime PM usage
counter which has no effect (all devices have nonzero runtime PM
usage counters during system-wide suspend and resume). It also calls
pm_runtime_mark_last_busy() for the device even though devices cannot
runtime-suspend during system-wide suspend and resume (because their
runtime PM usage counters are nonzero) and an analogous call is made
in the same function later. Moreover, it sets the runtime PM status
of the device to RPM_ACTIVE before activating it.
For the reasons listed above, remove that code altogether.
On top of that, add a pm_runtime_disable() call to intel_suspend() to
prevent the device from being runtime-resumed at any point after
intel_suspend() has started to manipulate it because the changes
made by that function would be undone by a runtime-suspend of the
device.
Next, once runtime PM has been disabled, the runtime PM status of the
device cannot change, so pm_runtime_status_suspended() can be used
instead of pm_runtime_suspended() in intel_suspend().
Finally, make intel_resume() call pm_runtime_set_active() at the end to
set the runtime PM status of the device to "active" because it has just
been activated and re-enable runtime PM for it after that.
Additionally, drop the setting of DPM_FLAG_SMART_SUSPEND from the
driver because it has no effect on devices handled by it.
Fixes: bca84a7b93 ("PM: sleep: Use DPM_FLAG_SMART_SUSPEND conditionally")
Reported-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Tested-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://patch.msgid.link/12680420.O9o76ZdvQC@rjwysocki.net
Pull soundwire updates from Vinod Koul:
- Support for SoundWire Bulk Register Access (BRA) protocol in core
along with Intel driver support and ASoC bits required
- AMD driver updates and support for ACP 7.0 and 7.1 platforms
* tag 'soundwire-6.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/soundwire: (28 commits)
soundwire: take in count the bandwidth of a prepared stream
ASoC: rt711-sdca: add DP0 support
soundwire: debugfs: add interface for BPT/BRA transfers
ASoC: SOF: Intel: hda-sdw-bpt: add CHAIN_DMA support
soundwire: intel_ace2x: add BPT send_async/wait callbacks
soundwire: intel: add BPT context definition
ASoC: SOF: Intel: hda-sdw-bpt: add helpers for SoundWire BPT DMA
soundwire: intel_auxdevice: add indirection for BPT send_async/wait
soundwire: cadence: add BTP/BRA helpers to format data
soundwire: bus: add bpt_stream pointer
soundwire: bus: add send_async/wait APIs for BPT protocol
soundwire: stream: reuse existing code for BPT stream
soundwire: stream: special-case the bus compute_params() routine
soundwire: stream: extend sdw_alloc_stream() to take 'type' parameter
soundwire: extend sdw_stream_type to BPT
soundwire: cadence: add BTP support for DP0
Documentation: driver: add SoundWire BRA description
soundwire: amd: change the log level for command response log
soundwire: slave: fix an OF node reference leak in soundwire slave device
soundwire: Use str_enable_disable-like helpers
...
Add definitions and helpers for the BPT/BRA protocol. Peripheral
drivers (aka ASoC codec drivers) can use this API to send bulk data
such as firmware or tables. The design intent is however NOT to
directly use this API but to rely on an intermediate regmap layer.
The API is only available when no other audio streams have been
allocated, and only one BTP/BRA stream is allowed per link. To avoid
the addition of yet another lock, the refcount tests are handled in
the stream master_runtime alloc/free routines where the bus_lock is
already held. Another benefit of this approach is that the same
bus_lock is used to handle runtime and port linked lists, which
reduces the potential for misaligned configurations.
In addition to exclusion with audio streams, BPT transfers have a lot
of overhead, specifically registers writes are needed to enable
transport in DP0. Most DMAs don't handle too well very small data sets
and they may have alignment limitations.
The size and alignment requirements are for now not handled by the
core but must be checked by platform-specific drivers.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.dev>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Liam Girdwood <liam.r.girdwood@intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Tested-by: shumingf@realtek.com
Link: https://lore.kernel.org/r/20250227140615.8147-8-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Replace ternary (condition ? "enable" : "disable") syntax with helpers
from string_choices.h because:
1. Simple function call with one argument is easier to read. Ternary
operator has three arguments and with wrapping might lead to quite
long code.
2. Is slightly shorter thus also easier to read.
3. It brings uniformity in the text - same string.
4. Allows deduping by the linker, which results in a smaller binary
file.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20250114200726.969501-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
For wake event, SoundWire host wake interrupt will be asserted based on
below pre-conditions for ACP7.0 & ACP7.1 platforms.
- ACP device should be in D0 state.
- SoundWire manager instance should be in D3 state.
- SoundWire manager device state should be set to D3.
- ACP_PME_EN should be set to 1.
Implement code changes to enable/disable SoundWire host wake interrupt mask
during suspend and resume as per design flow for ACP7.0 & ACP7.1 platforms.
Signed-off-by: Vijendar Mukunda <Vijendar.Mukunda@amd.com>
Link: https://lore.kernel.org/r/20250207065841.4718-7-Vijendar.Mukunda@amd.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Added qcom_swrm_set_channel_map api to set the master channel mask for
TX and RX paths based on the provided slots.
Added a new field ch_mask to the qcom_swrm_port_config structure.
This field is used to store the master channel mask, which allows more
flexible to configure channel mask in runtime for specific active
soundwire ports.
Modified the qcom_swrm_port_enable function to configure master
channel mask. If the ch_mask is set to SWR_INVALID_PARAM or is zero,
the function will use the default channel mask.
Signed-off-by: Mohammad Rafi Shaik <quic_mohs@quicinc.com>
Acked-by: Vinod Koul <vkoul@kernel.org>
Link: https://patch.msgid.link/20250206112225.3270400-4-quic_mohs@quicinc.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Pull soundwire updates from Vinod Koul:
- SoundWire multi lane support to use multiple lanes if supported
- Stream handling of DEPREPARED state
- AMD wake register programming for power off mode
* tag 'soundwire-6.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/soundwire:
soundwire: amd: clear wake enable register for power off mode
soundwire: generic_bandwidth_allocation: count the bandwidth of active streams only
SoundWire: pass stream to compute_params()
soundwire: generic_bandwidth_allocation: add lane in sdw_group_params
soundwire: generic_bandwidth_allocation: select data lane
soundwire: generic_bandwidth_allocation: check required freq accurately
soundwire: generic_bandwidth_allocation: correct clk_freq check in sdw_select_row_col
Soundwire: generic_bandwidth_allocation: set frame shape on fly
Soundwire: stream: program BUSCLOCK_SCALE
Soundwire: add sdw_slave_get_scale_index helper
soundwire: generic_bandwidth_allocation: skip DEPREPARED streams
soundwire: stream: set DEPREPARED state earlier
soundwire: add lane_used_bandwidth in struct sdw_bus
soundwire: mipi_disco: read lane mapping properties from ACPI
soundwire: add lane field in sdw_port_runtime
soundwire: bus: Move irq mapping cleanup into devres
The continual trickle of small conversion patches is grating on me, and
is really not helping. Just get rid of the 'remove_new' member
function, which is just an alias for the plain 'remove', and had a
comment to that effect:
/*
* .remove_new() is a relic from a prototype conversion of .remove().
* New drivers are supposed to implement .remove(). Once all drivers are
* converted to not use .remove_new any more, it will be dropped.
*/
This was just a tree-wide 'sed' script that replaced '.remove_new' with
'.remove', with some care taken to turn a subsequent tab into two tabs
to make things line up.
I did do some minimal manual whitespace adjustment for places that used
spaces to line things up.
Then I just removed the old (sic) .remove_new member function, and this
is the end result. No more unnecessary conversion noise.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull soundwire updates from Vinod Koul:
- structure optimization of few bus structures and header updates
- support for 2.0 disco spec
- amd driver updates for acp revision, refactoring code and support for
acp6.3
- soft reset support for cadence driver
* tag 'soundwire-6.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/soundwire: (24 commits)
soundwire: Minor formatting fixups in sdw.h header
soundwire: Update the includes on the sdw.h header
soundwire: cadence: clear MCP BLOCK_WAKEUP in init
soundwire: cadence: add soft-reset on startup
soundwire: intel_auxdevice: add kernel parameter for mclk divider
soundwire: mipi-disco: add support for DP0/DPn 'lane-list' property
soundwire: mipi-disco: add new properties from 2.0 spec
soundwire: mipi-disco: add comment on DP0-supported property
soundwire: mipi-disco: add support for peripheral channelprepare timeout
soundwire: mipi_disco: add support for clock-scales property
soundwire: mipi-disco: add error handling for property array read
soundwire: mipi-disco: remove DPn audio-modes
soundwire: optimize sdw_dpn_prop
soundwire: optimize sdw_dp0_prop
soundwire: optimize sdw_slave_prop
soundwire: optimize sdw_bus structure
soundwire: optimize sdw_master_prop
soundwire: optimize sdw_stream_runtime memory layout
soundwire: mipi_disco: add MIPI-specific property_read_bool() helpers
soundwire: Correct some typos in comments
...
