We need the USB fixes in here for other follow-on changes to be able to
be applied successfully.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix this compilation error seen when CONFIG_TRACING is not enabled:
drivers/scsi/qla2xxx/qla_os.c: In function 'qla_trace_init':
drivers/scsi/qla2xxx/qla_os.c:2854:25: error: implicit declaration of function
'trace_array_get_by_name'; did you mean 'trace_array_set_clr_event'?
[-Werror=implicit-function-declaration]
2854 | qla_trc_array = trace_array_get_by_name("qla2xxx");
| ^~~~~~~~~~~~~~~~~~~~~~~
| trace_array_set_clr_event
drivers/scsi/qla2xxx/qla_os.c: In function 'qla_trace_uninit':
drivers/scsi/qla2xxx/qla_os.c:2869:9: error: implicit declaration of function
'trace_array_put' [-Werror=implicit-function-declaration]
2869 | trace_array_put(qla_trc_array);
| ^~~~~~~~~~~~~~~
Link: https://lore.kernel.org/r/20220907233308.4153-2-aeasi@marvell.com
Reported-by: kernel test robot <lkp@intel.com>
Reviewed-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Signed-off-by: Arun Easi <aeasi@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When a UART port is newly registered, uart_configure_port() seeks to
deassert RS485 Transmit Enable by setting the RTS bit in port->mctrl.
However a number of UART drivers interpret a set RTS bit as *assertion*
instead of deassertion: Affected drivers include those using
serial8250_em485_config() (except 8250_bcm2835aux.c) and some using
mctrl_gpio (e.g. imx.c).
Since the interpretation of the RTS bit is driver-specific, it is not
suitable as a means to centrally deassert Transmit Enable in the serial
core. Instead, the serial core must call on drivers to deassert it in
their driver-specific way. One way to achieve that is to call
->rs485_config(). It implicitly deasserts Transmit Enable.
So amend uart_configure_port() and uart_resume_port() to invoke
uart_rs485_config(). That allows removing calls to uart_rs485_config()
from drivers' ->probe() hooks and declaring the function static.
Skip any invocation of ->set_mctrl() if RS485 is enabled. RS485 has no
hardware flow control, so the modem control lines are irrelevant and
need not be touched. When leaving RS485 mode, reset the modem control
lines to the state stored in port->mctrl. That way, UARTs which are
muxed between RS485 and RS232 transceivers drive the lines correctly
when switched to RS232. (serial8250_do_startup() historically raises
the OUT1 modem signal because otherwise interrupts are not signaled on
ancient PC UARTs, but I believe that no longer applies to modern,
RS485-capable UARTs and is thus safe to be skipped.)
imx.c modifies port->mctrl whenever Transmit Enable is asserted and
deasserted. Stop it from doing that so port->mctrl reflects the RS232
line state.
8250_omap.c deasserts Transmit Enable on ->runtime_resume() by calling
->set_mctrl(). Because that is now a no-op in RS485 mode, amend the
function to call serial8250_em485_stop_tx().
fsl_lpuart.c retrieves and applies the RS485 device tree properties
after registering the UART port. Because applying now happens on
registration in uart_configure_port(), move retrieval of the properties
ahead of uart_add_one_port().
Link: https://lore.kernel.org/all/20220329085050.311408-1-matthias.schiffer@ew.tq-group.com/
Link: https://lore.kernel.org/all/8f538a8903795f22f9acc94a9a31b03c9c4ccacb.camel@ginzinger.com/
Fixes: d3b3404df3 ("serial: Fix incorrect rs485 polarity on uart open")
Cc: stable@vger.kernel.org # v4.14+
Reported-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Reported-by: Roosen Henri <Henri.Roosen@ginzinger.com>
Tested-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Link: https://lore.kernel.org/r/2de36eba3fbe11278d5002e4e501afe0ceaca039.1663863805.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jonathan writes:
Second set of IIO new device support, features and cleanup for the 6.1 cycle.
Normal mixed bag of new device support with continuing trend that most new
devices are supported by extending existing drivers - a positive sign perhaps
that device manufacturers have somewhat stabilized their interfaces across
product generations. The BNO055 driver was however a substantial addition
including several additions to the IIO core.
There are a number of significant patch sets under review, so if the 6.0
cycle runs long I may send a 3rd pull request.
New device support
* adi,adxl313
- Support for the ADXL312 and ADXL314 accelerometers.
* bosch,bmp280
- Support for the BMP380 family of pressures sensors.
Included considerable refactoring and modernization of the bmp280
driver.
* bosch,bno055
- New driver for this i2c/serial attached complex IMU.
* lltc,ltc2497
- Support for the LTC2499 16 channel, 24bit ADC.
* st,pressure
- Support for the LPS22DF pressure sensor
* st,lsm6dsx
- Support for the LSM6DSTX (Mainly adding the ID and WAI)
Features
* core - to support the bosch,bno055 requirements
- Support for linear acceleration channel type (effect of gravity removed)
- Pitch, yaw and roll modifiers for angle channels.
- Standard serialnumber attribute documentation.
- Binary attributes - to allow for calibration save and restore.
* adi,ad7923
- Support extended range (wider supported input voltage range).
* bosch,bmp280
- Add filter controls for some supported parts.
* microchip,mcp3911
- Buffered capture support for this ADC.
- Data ready interrupt support, including hiz control for line.
- Oversampling ratio support.
* st,stm32-adc
- Support ID registers on parts where they are present, providing
discoverability of some features.
Fixes - late breaking fixes that I judged could wait for the merge window.
* adi,ad5593r
- Add a missing STOP condition between address write and data read.
- Check for related i2c functionality.
* adi,ad7923
- Fix shift reporting for some variants supported by the driver.
* infinion,dps310
- Work around a hardware issue where a chip can hang by adding a
timeout and reset path.
Cleanups
* Continuing work to switch to new pm macros.
* MAINTAINERS
- Drop duplication of wild card covered entry in ADI block and
add missing entries to cover ltc294x binding files.
* bosch,bma400
- Fix trivial smatch warning.
* bosch,bmp280
- Fix broken links to datasheets
* lltc,ltc2497
- Fix missing entry for ltc2499
* mexelis,mlx90614
- Switch to get_avail() callback for _available attributes.
* microchip,mcp3911
- Move to devm_ resource management for all elements of probe()
* tag 'iio-for-6.1b' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio: (57 commits)
iio: adc: mcp3911: add support for oversampling ratio
dt-bindings: iio: adc: mcp3911: add microchip,data-ready-hiz entry
iio: adc: mcp3911: add support for interrupts
iio: adc: mcp3911: add support for buffers
iio: adc: mcp3911: use resource-managed version of iio_device_register
iio: accel: bma400: Fix smatch warning based on use of unintialized value.
iio: light: st_uvis25: Use EXPORT_NS_SIMPLE_DEV_PM_OPS()
iio: accel: bmi088: Use EXPORT_NS_GPL_RUNTIME_DEV_PM_OPS() and pm_ptr()
iio: proximity: srf04: Use pm_ptr() to remove unused struct dev_pm_ops
iio: proximity: sx9360: Switch to DEFINE_SIMPLE_DEV_PM_OPS() and pm_sleep_ptr()
iio: proximity: sx9324: Switch to DEFINE_SIMPLE_DEV_PM_OPS() and pm_sleep_ptr()
iio: proximity: sx9310: Switch to DEFINE_SIMPLE_DEV_PM_OPS() and pm_sleep_ptr()
docs: iio: add documentation for BNO055 driver
iio: imu: add BNO055 I2C driver
iio: imu: add BNO055 serdev driver
dt-bindings: iio/imu: Add Bosch BNO055
iio: document "serialnumber" sysfs attribute
iio: document bno055 private sysfs attributes
iio: imu: add Bosch Sensortec BNO055 core driver
iio: add support for binary attributes
...
At present, the tps68470.c only supports a single clock consumer when
passing platform data to the clock driver. In some devices multiple
sensors depend on the clock provided by a single TPS68470 and so all
need to be able to acquire the clock. Support passing multiple
consumers as platform data.
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Daniel Scally <djrscally@gmail.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Add a helper macro to iterate over ACPI devices that are flagged
as consumers of an initial supplier ACPI device.
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Daniel Scally <djrscally@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
In commit b83e2b3067 ("ACPI: scan: Add function to fetch dependent
of ACPI device") we added a means of fetching the first device to
declare itself dependent on another ACPI device in the _DEP method.
One assumption in that patch was that there would only be a single
consuming device, but this has not held.
Replace that function with a new function that fetches the next consumer
of a supplier device. Where no "previous" consumer is passed in, it
behaves identically to the original function.
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Daniel Scally <djrscally@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
PCC regions utilize a mailbox to set/retrieve register values used by
the CPPC code. This is fine as long as the operations are
infrequent. With the FIE code enabled though the overhead can range
from 2-11% of system CPU overhead (ex: as measured by top) on Arm
based machines.
So, before enabling FIE assure none of the registers used by
cppc_get_perf_ctrs() are in the PCC region. Finally, add a module
parameter which can override the PCC region detection at boot or
module reload.
Signed-off-by: Jeremy Linton <jeremy.linton@arm.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Ionela Voinescu <ionela.voinescu@arm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Use _DMA defined in ACPI spec for translation between
DMA address and CPU address, and implement acpi_arch_dma_setup
for initializing dev->dma_range_map, where acpi_dma_get_range
is called for parsing _DMA.
e.g.
If we have two dma ranges:
cpu address dma address size offset
0x200080000000 0x2080000000 0x400000000 0x1fe000000000
0x400080000000 0x4080000000 0x400000000 0x3fc000000000
_DMA for pci devices should be declared in host bridge as
flowing:
Name (_DMA, ResourceTemplate() {
QWordMemory (ResourceProducer,
PosDecode,
MinFixed,
MaxFixed,
NonCacheable,
ReadWrite,
0x0,
0x4080000000,
0x447fffffff,
0x3fc000000000,
0x400000000,
,
,
)
QWordMemory (ResourceProducer,
PosDecode,
MinFixed,
MaxFixed,
NonCacheable,
ReadWrite,
0x0,
0x2080000000,
0x247fffffff,
0x1fe000000000,
0x400000000,
,
,
)
})
Acked-by: Huacai Chen <chenhuacai@loongson.cn>
Signed-off-by: Jianmin Lv <lvjianmin@loongson.cn>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
In DT systems configurations, of_dma_get_range() returns struct
bus_dma_region DMA regions; they are used to set-up devices
DMA windows with different offset available for translation between DMA
address and CPU address.
In ACPI systems configuration, acpi_dma_get_range() does not return
DMA regions yet and that precludes setting up the dev->dma_range_map
pointer and therefore DMA regions with multiple offsets.
Update acpi_dma_get_range() to return struct bus_dma_region
DMA regions like of_dma_get_range() does.
After updating acpi_dma_get_range(), acpi_arch_dma_setup() is changed for
ARM64, where the original dma_addr and size are removed as these
arguments are now redundant, and pass 0 and U64_MAX for dma_base
and size of arch_setup_dma_ops; this is a simplification consistent
with what other ACPI architectures also pass to iommu_setup_dma_ops().
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Jianmin Lv <lvjianmin@loongson.cn>
Reviewed-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Pull tty/serial driver fixes from Greg KH:
"Here are some small, and late, serial driver fixes for 6.0-rc7 to
resolve some reported problems.
Included in here are:
- tegra icount accounting fixes, including a framework function that
other drivers will be converted over to using in 6.1-rc1.
- fsl_lpuart reset bugfix
- 8250 omap 485 bugfix
- sifive serial clock bugfix
The last three patches have not shown up in linux-next due to them
being added to my tree only 2 days ago, but they are tiny and
self-contained and the developers say they resolve issues that they
have with 6.0-rc. The other three have been in linux-next for a while
with no reported issues"
* tag 'tty-6.0-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
serial: sifive: enable clocks for UART when probed
serial: 8250: omap: Use serial8250_em485_supported
serial: fsl_lpuart: Reset prior to registration
serial: tegra-tcu: Use uart_xmit_advance(), fixes icount.tx accounting
serial: tegra: Use uart_xmit_advance(), fixes icount.tx accounting
serial: Create uart_xmit_advance()
upgrade the callchain to drm_dbg() and drm_dev_dbg(); add a struct
_ddebug ptr parameter to them, and supply that additional param by
replacing the '_no_desc' flavor of dyndbg Factory macro currently used
with the flavor that supplies the descriptor.
NOTES:
The descriptor gives these fns access to the decorator flags, but they
do none of the dynamic-prefixing done by dynamic_emit_prefix(), which
is currently static.
DRM already has conventions for logging/messaging; just tossing
optional decorations on top probably wouldn't help. Instead, existing
flags (or new ones, perhaps 'sd' ala lspci) can be used to make
current message conventions optional. This suggests a new
drmdbg_prefix_emit() to handle prefixing locally.
For CONFIG_DRM_USE_DYNAMIC_DEBUG=N, just pass null descriptor.
desc->class_id is redundant with category parameter, but its
availability is dependent on desc.
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Link: https://lore.kernel.org/r/20220912052852.1123868-10-jim.cromie@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When CONFIG_DRM_USE_DYNAMIC_DEBUG=y, the drm.debug API (a macro stack,
calling _+drm_*dbg() eventually) invokes a dyndbg Factory macro to
create a descriptor for each callsite, thus making them individually
>control-able.
In this case, the calls to _drm_*dbg are unreachable unless the
callsite is enabled. So those calls can short-circuit their early
do-nothing returns. Provide and use __drm_debug_enabled(), to do this
when config'd, or the _raw flags-check otherwize.
And since dyndbg is in use, lets also instrument the remaining users
of drm_debug_enabled, by wrapping the _raw in a macro with a:
pr_debug("todo: is this frequent enough to optimize ?\n");
For CONFIG_DRM_USE_DYNAMIC_DEBUG=n, do no site instrumenting at all,
since JUMP_LABEL might be off, and we don't want to make work.
With drm, amdgpu, i915, nouveau loaded, heres remaining uses of
drm_debug_enabled(), which costs ~1.5kb data to control the
pr_debug("todo:..")s.
Some of those uses might be ok to use __drm_debug_enabled() by
inspection, others might warrant conversion to use dyndbg Factory
macros, and that would want callrate data to estimate the savings
possible. TBH, any remaining savings are probably small; drm.debug
covers the vast bulk of the uses. Maybe "vblank" is the exception.
:#> grep todo /proc/dynamic_debug/control | wc
21 168 2357
:#> grep todo /proc/dynamic_debug/control
drivers/gpu/drm/drm_edid_load.c:178 [drm]edid_load =_ "todo: maybe avoid via dyndbg\n"
drivers/gpu/drm/drm_vblank.c:410 [drm]drm_crtc_accurate_vblank_count =_ "todo: maybe avoid via dyndbg\n"
drivers/gpu/drm/drm_vblank.c:787 [drm]drm_crtc_vblank_helper_get_vblank_timestamp_internal =_ "todo: maybe avoid via dyndbg\n"
drivers/gpu/drm/drm_vblank.c:1491 [drm]drm_vblank_restore =_ "todo: maybe avoid via dyndbg\n"
drivers/gpu/drm/drm_vblank.c:1433 [drm]drm_vblank_enable =_ "todo: maybe avoid via dyndbg\n"
drivers/gpu/drm/drm_plane.c:2168 [drm]drm_mode_setplane =_ "todo: maybe avoid via dyndbg\n"
drivers/gpu/drm/display/drm_dp_mst_topology.c:1359 [drm_display_helper]drm_dp_mst_wait_tx_reply =_ "todo: maybe avoid via dyndbg\n"
drivers/gpu/drm/display/drm_dp_mst_topology.c:2864 [drm_display_helper]process_single_tx_qlock =_ "todo: maybe avoid via dyndbg\n"
drivers/gpu/drm/display/drm_dp_mst_topology.c:2909 [drm_display_helper]drm_dp_queue_down_tx =_ "todo: maybe avoid via dyndbg\n"
drivers/gpu/drm/display/drm_dp_mst_topology.c:1686 [drm_display_helper]drm_dp_mst_update_slots =_ "todo: maybe avoid via dyndbg\n"
drivers/gpu/drm/i915/display/intel_dp.c:1111 [i915]intel_dp_print_rates =_ "todo: maybe avoid via dyndbg\n"
drivers/gpu/drm/i915/display/intel_backlight.c:5434 [i915]cnp_enable_backlight =_ "todo: maybe avoid via dyndbg\n"
drivers/gpu/drm/i915/display/intel_backlight.c:5459 [i915]intel_backlight_device_register =_ "todo: maybe avoid via dyndbg\n"
drivers/gpu/drm/i915/display/intel_opregion.c:43 [i915]intel_opregion_notify_encoder =_ "todo: maybe avoid via dyndbg\n"
drivers/gpu/drm/i915/display/intel_opregion.c:53 [i915]asle_set_backlight =_ "todo: maybe avoid via dyndbg\n"
drivers/gpu/drm/i915/display/intel_bios.c:1088 [i915]intel_bios_is_dsi_present =_ "todo: maybe avoid via dyndbg\n"
drivers/gpu/drm/i915/display/intel_display_debugfs.c:6153 [i915]i915_drrs_ctl_set =_ "todo: maybe avoid via dyndbg\n"
drivers/gpu/drm/i915/intel_pcode.c:26 [i915]snb_pcode_read =_ "todo: maybe avoid via dyndbg\n"
drivers/gpu/drm/i915/i915_getparam.c:785 [i915]i915_getparam_ioctl =_ "todo: maybe avoid via dyndbg\n"
drivers/gpu/drm/amd/amdgpu/vcn_v2_5.c:282 [amdgpu]vcn_v2_5_process_interrupt =_ "todo: maybe avoid via dyndbg\n"
drivers/gpu/drm/amd/amdgpu/vcn_v2_0.c:433 [amdgpu]vcn_v2_0_process_interrupt =_ "todo: maybe avoid via dyndbg\n"
:#>
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Link: https://lore.kernel.org/r/20220912052852.1123868-8-jim.cromie@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
drm_print defines all of these:
drm_dbg_{core,kms,prime,atomic,vbl,lease,_dp,_drmres}
but not drm_dbg_driver itself, since it was the original drm_dbg.
To improve namespace symmetry, change the drm_dbg defn to
drm_dbg_driver, and redef grandfathered name to symmetric one.
This will help with nouveau, which uses its own stack of macros to
construct calls to dev_info, dev_dbg, etc, for which adaptation means
drm_dbg_##driver constructs.
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Link: https://lore.kernel.org/r/20220912052852.1123868-7-jim.cromie@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
lkp robot told me:
>> drivers/gpu/drm/drm_ioc32.c:989:2:
error: call to undeclared function '_dynamic_func_call_cls';
ISO C99 and later do not support implicit function declarations
[-Wimplicit-function-declaration]
DRM_DEBUG("comm=\"%s\", pid=%d, dev=0x%lx, auth=%d, %s\n",
Since that macro is defined in drm_print.h, and under DRM_USE_DYN*=y
configs, invokes dyndbg-factory macros, include dynamic_debug.h from
there too, so that those configs have the definitions of all the
macros in the callchain.
This is done as a separate patch mostly to see how lkp sorts it.
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Link: https://lore.kernel.org/r/20220912052852.1123868-6-jim.cromie@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For CONFIG_DRM_USE_DYNAMIC_DEBUG=y, wrap __drm_dbg() & __drm_dev_dbg()
in one of dyndbg's Factory macros: _dynamic_func_call_no_desc().
This adds the callsite descriptor into the code, and an entry for each
into /proc/dynamic_debug/control.
#> echo class DRM_UT_ATOMIC +p > /proc/dynamic_debug/control
CONFIG_DRM_USE_DYNAMIC_DEBUG=y/n is configurable because of the .data
footprint cost of per-callsite control; 56 bytes/site * ~2k for i915,
~4k callsites for amdgpu. This is large enough that a kernel builder
might not want it.
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Link: https://lore.kernel.org/r/20220912052852.1123868-5-jim.cromie@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
change drm_dev_dbg & drm_dbg to macros, which forward to the renamed
functions (with __ prefix added).
Those functions sit below the categorized layer of macros implementing
the DRM debug.category API, and implement most of it. These are good
places to insert dynamic-debug jump-label mechanics, which will allow
DRM to avoid the runtime cost of drm_debug_enabled().
no functional changes.
memory cost baseline: (unchanged)
bash-5.1# drms_load
[ 9.220389] dyndbg: 1 debug prints in module drm
[ 9.224426] ACPI: bus type drm_connector registered
[ 9.302192] dyndbg: 2 debug prints in module ttm
[ 9.305033] dyndbg: 8 debug prints in module video
[ 9.627563] dyndbg: 127 debug prints in module i915
[ 9.721505] AMD-Vi: AMD IOMMUv2 functionality not available on this system - This is not a bug.
[ 10.091345] dyndbg: 2196 debug prints in module amdgpu
[ 10.106589] [drm] amdgpu kernel modesetting enabled.
[ 10.107270] amdgpu: CRAT table not found
[ 10.107926] amdgpu: Virtual CRAT table created for CPU
[ 10.108398] amdgpu: Topology: Add CPU node
[ 10.168507] dyndbg: 3 debug prints in module wmi
[ 10.329587] dyndbg: 3 debug prints in module nouveau
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Link: https://lore.kernel.org/r/20220912052852.1123868-4-jim.cromie@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use DECLARE_DYNDBG_CLASSMAP across DRM:
- in .c files, since macro defines/initializes a record
- in drivers, $mod_{drv,drm,param}.c
ie where param setup is done, since a classmap is param related
- in drm/drm_print.c
since existing __drm_debug param is defined there,
and we ifdef it, and provide an elaborated alternative.
- in drm_*_helper modules:
dp/drm_dp - 1st item in makefile target
drivers/gpu/drm/drm_crtc_helper.c - random pick iirc.
Since these modules all use identical CLASSMAP declarations (ie: names
and .class_id's) they will all respond together to "class DRM_UT_*"
query-commands:
:#> echo class DRM_UT_KMS +p > /proc/dynamic_debug/control
NOTES:
This changes __drm_debug from int to ulong, so BIT() is usable on it.
DRM's enum drm_debug_category values need to sync with the index of
their respective class-names here. Then .class_id == category, and
dyndbg's class FOO mechanisms will enable drm_dbg(DRM_UT_KMS, ...).
Though DRM needs consistent categories across all modules, thats not
generally needed; modules X and Y could define FOO differently (ie a
different NAME => class_id mapping), changes are made according to
each module's private class-map.
No callsites are actually selected by this patch, since none are
class'd yet.
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Link: https://lore.kernel.org/r/20220912052852.1123868-3-jim.cromie@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
enum drm_debug_category has 10 categories, but is initialized with
bitmasks which require 10 bits of underlying storage. By using
natural enumeration, and moving the BIT(cat) into drm_debug_enabled(),
the enum fits in 4 bits, allowing the category to be represented
directly in pr_debug callsites, via the ddebug.class_id field.
While this slightly pessimizes the bit-test in drm_debug_enabled(),
using dyndbg with JUMP_LABEL will avoid the function entirely.
NOTE: this change forecloses the possibility of doing:
drm_dbg(DRM_UT_CORE|DRM_UT_KMS, "weird 2-cat experiment")
but thats already strongly implied by the use of the enum itself; its
not a normal enum if it can be 2 values simultaneously.
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Link: https://lore.kernel.org/r/20220912052852.1123868-2-jim.cromie@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The last user was removed in 5.1 in
commit 08300f4402 ("a.out: remove core dumping support")
but this is part of the UAPI headers, so this may want to either wait
until a.out is removed entirely, or be removed from the magic number doc
and silently remain in the header
A cursory glance on DCS didn't show any user code actually using this
value
Found with
grep MAGIC Documentation/process/magic-number.rst | while read -r mag _;
do git grep -wF "$mag" | grep -ve '^Documentation.*magic-number.rst:' \
-qe ':#define '"$mag" || git grep -wF "$mag" | while IFS=: read -r f _;
do sed -i '/\b'"$mag"'\b/d' "$f"; done ; done
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Link: https://lore.kernel.org/r/9cbea062df7125ef43e2e0b2a67ede6ad1c5f27e.1663280877.git.nabijaczleweli@nabijaczleweli.xyz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This merges the driver core changes in 6.0-rc7 into driver-core-next as
they are needed here as well for testing.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The PCI hybrid card NotOnlyTV LV3H has a built-in IR receiver connected
via I2C bus, currently not supported. This receiver is probably present
in more Geniatech cards. It has no capability for repeating when a key is
held down.
Add support for this built-in IR receiver. Use the existing Total Media
In Hand_02 remote keytable (Geniatech Mygica X8507) which matches exactly
the LV3H remote.
Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
Signed-off-by: Marek Kidawski <mark_kiddy@wp.pl>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
It renames aria to aria_generic and exports some functions such as
aria_set_key(), aria_encrypt(), and aria_decrypt() to be able to be
used by aria-avx implementation.
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Add a new media entity operation, has_pad_interdep. The optional op is
used to discover the pad interdependencies inside an entity during the
pipeline construction.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
[Note: the code is mostly from Laurent but the patch description is from Tomi]
The media_pipeline_start() and media_pipeline_stop() functions use the
media graph walk API to traverse the graph and validate the pipeline.
The graph walk traverses the media graph following links between the
entities.
Also, while the pipeline can't change between the start and stop calls,
the graph is walked again from scratch at stop time, or any time a
driver needs to inspect the pipeline.
With the upcoming multiplexed streams support we will need a bit more
intelligent pipeline construction, as e.g. two independent streams may
be passing through a single entity via separate pads in which case
those pads should not be part of the same pipeline.
This patch essentially rewrites the media_pipeline_start/stop so that
a pipeline is defined as a set of pads instead of entities and the media
graph traversal considers the pad interdependencies when choosing which
links to follow.
Currently all the entity's pads are considered as interdependent. This
means that the behavior with all the current drivers stays the same, but
in the future we can define a more fine-grained pipeline construction.
Additionally the media pipeline's pads are cached at
media_pipeline_start() time, and re-used at media_pipeline_stop() which
avoid the need to re-walk the whole graph as the previous implementation
did.
Also, caching pads in the pipeline can serve in the future as the
foundation to provide a better API than the media graph walk to drivers
to iterate over pads and entities in the pipeline.
Note that the old media_pipeline_start/stop used the media graph walk
API. The new version does not use the media graph walk API, but instead
a new implementation.
There are two reasons for not changing the graph walk: it proved to be
rather difficult to change the graph walk to have the features
implemented in this patch, and second, this keeps the backward
compatibility of the graph walk as there are users of the graph walk API
The long term plan is that all the existing code would be converted to
use the new cached pipeline, thus allowing us to remove the graph walk.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Add new variant of media_pipeline_start(), media_pipeline_alloc_start().
media_pipeline_alloc_start() can be used by drivers that do not need to
extend the media_pipeline. The function will either use the pipeline
already associated with the entity, if such exists, or allocate a new
pipeline.
When media_pipeline_stop() is called and the pipeline's use count drops
to zero, the pipeline is automatically freed.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
With the upcoming stream related improvements to the pipelines, the
pipelines are moved from media entities to media pads. As the drivers
currently use the pipelines with the entity based model, moving the
pipelines to pads will cause changes to the drivers.
However, most of the uses of media pipelines are related to a video
device (a DMA engine) with a single pad, and thus there's never a need
to support multiple pads in these use cases. We can avoid pushing the
complexities of the pad based model to the drivers by adding video
device wrappers for the pipeline related functions.
This patch adds a number of wrappers to media_pipeline functions, all of
which take a video_device as a parameter (instead of a media_entity),
and verify that there's just one pad.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Replace direct access to the pipe field in drivers with a new helper
function. This will allow easier refactoring of media pipeline handling
in the MC core behind the scenes without affecting drivers.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The media_entity_enum_init() function is a wrapper around
__media_entity_enum_init() that turns a media_device pointer argument
into the maximum entity ID in the corresponding media graph.
__media_entity_enum_init() is never used outside of
media_entity_enum_init(), so the two functions can be merged together.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
V4L2_FRAME_DESC_ENTRY_MAX is currently set to 4. In theory it's possible
to have an arbitrary amount of streams in a single pad, so preferably
there should be no hardcoded maximum number.
However, I believe a reasonable max is 8, which would cover a CSI-2 pad
with 4 streams of pixel data and 4 streams of metadata.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
struct v4l2_fwnode_endpoint was zeroed previously apart from the endpoint
information itself when the endpoint properties were parsed. Now this
hasn't been the case for a few years so remove the comment.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The state argument for the functions for obtaining various parts of the
state is NULL if it is called by drivers for active state. Fail graciously
in that case instead of dereferencing a NULL pointer.
Suggested-by: Bingbu Cao <bingbu.cao@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The doc says the I²C device's name is used if devname is NULL, but
actually the I²C device driver's name is used.
Fixes: 0658293012 ("media: v4l: subdev: Add a function to set an I²C sub-device's name")
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Add support for this new CEC message. This was added in HDMI 2.1a.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The type ops for equal, init and validate have an elems argument,
but this can be taken from struct v4l2_ctrl: ctrl->elems for
equal and init, and ctrl->new_elems for validate (since you are
validating a new control value).
So drop this argument and update all callers.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
