DM maps DRM CRTC degamma to DPP (pre-blending) degamma block, but DCE doesn't
support programmable degamma curve anywhere. Currently, a custom degamma is
accepted by DM but just ignored by DCE driver and degamma correction isn't
actually applied. There is no way to map custom degamma in DCE, therefore, DRM
CRTC degamma property shouldn't be enabled for DCE drivers.
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Melissa Wen <mwen@igalia.com>
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
[WHY?]
DCN32 uses fclk pstate watermarks for dummy pstate, and must always be
supported.
[HOW?]
Validation needs to be run with fclk pstate latency set
as the dummy pstate latency to get correct prefetch and bandwidth outputs.
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Dillon Varone <Dillon.Varone@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
dcn314 uses optc2_configure_crc() that wraps
optc1_configure_crc() + set additional registers
not applicable to dcn314.
It's not critical but when used leads to warning like:
WARNING: drivers/gpu/drm/amd/amdgpu/../display/dc/dc_helper.c
Call Trace:
<TASK>
generic_reg_set_ex+0x6d/0xe0 [amdgpu]
optc2_configure_crc+0x60/0x80 [amdgpu]
dc_stream_configure_crc+0x129/0x150 [amdgpu]
amdgpu_dm_crtc_configure_crc_source+0x5d/0xe0 [amdgpu]
[How]
Use optc1_configure_crc() directly
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org # 6.0.x
[Why]
The cursor size (in memory) is currently incorrectly calculated,
resulting not enough CAB being allocated for static screen cursor
in MALL refresh. This results in cursor image corruption.
[How]
Use cursor pitch instead of cursor width when calculating cursor size.
Update num cache lines calculation to use the result of the cursor size
calculation instead of manually recalculating again.
Reviewed-by: Alvin Lee <Alvin.Lee2@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: George Shen <george.shen@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org # 6.0.x
[Why]
Some DPIA AUX replies have incorrect data length from original request.
This could lead to overwriting of destination buffer if reply length is
larger, which could cause invalid access to stack since many destination
buffers are declared as local variables.
[How]
Check for invalid length from DPIA AUX replies and trigger a retry if
reply length is not the same as original request. A DRM_WARN() dmesg log
is also produced.
Reviewed-by: Roman Li <Roman.Li@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Stylon Wang <stylon.wang@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org # 6.0.x
On IGT, there is a test named amd_hotplug, and when the subtest basic is
executed on DCN31, we get the following error:
[drm] *ERROR* [CRTC:71:crtc-0] flip_done timed out
[drm] *ERROR* flip_done timed out
[drm] *ERROR* [CRTC:71:crtc-0] commit wait timed out
[drm] *ERROR* flip_done timed out
[drm] *ERROR* [CONNECTOR:88:DP-1] commit wait timed out
[drm] *ERROR* flip_done timed out
[drm] *ERROR* [PLANE:59:plane-3] commit wait timed out
After enable the page flip log with the below command:
echo -n 'format "[PFLIP]" +p' > /sys/kernel/debug/dynamic_debug/control
It is possible to see that the flip was submitted, but DC never replied
back, which generates time-out issues. This is an indication that the
HUBP surface flip is missing. This commit fixes this issue by adding
hubp1_set_flip_int to DCN31.
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
[Why]
Since introduction of patch "Query DPIA HPD status.", link detection at
boot could be accessing DPIA AUX, which will not succeed until
DMUB outbox messaging is enabled and results in below dmesg logs:
[ 160.840227] [drm:amdgpu_dm_process_dmub_aux_transfer_sync [amdgpu]] *ERROR* wait_for_completion_timeout timeout!
[How]
Enable DMUB outbox messaging before link detection at boot time.
Reviewed-by: Wayne Lin <Wayne.Lin@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Stylon Wang <stylon.wang@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org # 6.0.x
When p->gang_size equals 0, amdgpu_cs_pass1() will return directly
without freeing chunk_array, which will cause a memory leak issue,
this patch fixes it.
Fixes: 4624459c84 ("drm/amdgpu: add gang submit frontend v6")
Reviewed-by: Luben Tuikov <luben.tuikov@amd.com>
Signed-off-by: Dong Chenchen <dongchenchen2@huawei.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The drm_atomic_get_new_private_obj_state() function returns NULL
on error path, drm_atomic_get_old_private_obj_state() function
returns NULL on error path, too, they does not return error pointers.
By the way, vc4_hvs_get_new/old_global_state() should return
ERR_PTR(-EINVAL), otherwise there will be null-ptr-defer issue,
such as follows:
In function vc4_atomic_commit_tail():
|-- old_hvs_state = vc4_hvs_get_old_global_state(state); <-- return NULL
|-- if (WARN_ON(IS_ERR(old_hvs_state))) <-- no return
|-- unsigned long state_rate = max(old_hvs_state->core_clock_rate,
new_hvs_state->core_clock_rate); <-- null-ptr-defer
Fixes: 9ec03d7f1e ("drm/vc4: kms: Wait on previous FIFO users before a commit")
Signed-off-by: Gaosheng Cui <cuigaosheng1@huawei.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20221110094445.2930509-6-cuigaosheng1@huawei.com
Currently, we are calling fill_dc_dirty_rects() even if PSR isn't
supported by the relevant link in amdgpu_dm_commit_planes(), this is
undesirable especially because when drm.debug is enabled we are printing
messages in fill_dc_dirty_rects() that are only useful for debugging PSR
(and confusing otherwise). So, we can instead limit the filling of dirty
rectangles to only when PSR is enabled.
Reviewed-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Re-take the eviction lock immediately again after the allocation is
completed, to fix circular locking warning with drm_buddy allocator.
Move amdgpu_vm_eviction_lock/unlock/trylock to amdgpu_vm.h as they are
called from multiple files.
Signed-off-by: Philip Yang <Philip.Yang@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Get below kernel WARNING backtrace when pressing ctrl-C to kill kfdtest
application.
If amdgpu_cs_parser_bos returns error after taking bo_list_mutex, as
caller amdgpu_cs_ioctl will not unlock bo_list_mutex, this generates the
kernel WARNING.
Add unlock bo_list_mutex after amdgpu_cs_parser_bos error handling to
cleanup bo_list userptr bo.
WARNING: kfdtest/2930 still has locks held!
1 lock held by kfdtest/2930:
(&list->bo_list_mutex){+.+.}-{3:3}, at: amdgpu_cs_ioctl+0xce5/0x1f10 [amdgpu]
stack backtrace:
dump_stack_lvl+0x44/0x57
get_signal+0x79f/0xd00
arch_do_signal_or_restart+0x36/0x7b0
exit_to_user_mode_prepare+0xfd/0x1b0
syscall_exit_to_user_mode+0x19/0x40
do_syscall_64+0x40/0x80
Signed-off-by: Philip Yang <Philip.Yang@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This reverts commit 4545ae2ed3.
The origin patch "drm/amdgpu: getting fan speed pwm for vega10 properly" works fine.
Test failure is caused by test case self.
Signed-off-by: Asher Song <Asher.Song@amd.com>
Reviewed-by: Guchun Chen <guchun.chen@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY?]
Data return times when using lowest memclk can be <= 60us, which can cause
underflow on high bandwidth displays with a workload.
[HOW?]
Enforce a minimum prefetch time during validation for low memclk modes.
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Alan Liu <HaoPing.Liu@amd.com>
Signed-off-by: Dillon Varone <Dillon.Varone@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The link enablement sequence can end up resetting the encoder while
the PHY symclk isn't yet on.
This means that waiting for symclk on will timeout, along with the reset
bit never asserting high.
This causes unnecessary delay when enabling the link and produces a
warning affecting multiple IGT tests.
[How]
Don't wait for the symclk to be on here because firmware already does.
Don't wait for reset if we know the symclk isn't on.
Split the reset into a helper function that checks the bit and decides
whether or not a delay is sufficient.
Reviewed-by: Roman Li <Roman.Li@amd.com>
Acked-by: Alan Liu <HaoPing.Liu@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org # 6.0.x
[Why]
Recent backports from open source do not have header inclusion pattern
that is consistent with inclusion style in the rest of the file. This
breaks the internal tool builds as well. A recent commit erronously
modified the original DML formula for calculating
ActiveClockChangeLatencyHidingY. This resulted in a FCLK deviation
from the golden values.
[How]
Change the way in which display_mode_vba.h is included so that it is
consistent with the inclusion style in rest of the file which also fixes
the tool build. Restore the DML formula to its original state to fix the
FCLK deviation.
Reviewed-by: Aurabindo Pillai <Aurabindo.Pillai@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Alan Liu <HaoPing.Liu@amd.com>
Signed-off-by: Chaitanya Dhere <chaitanya.dhere@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Checkpoint BOs last. That way we don't need to close dmabuf FDs if
something else fails later. This avoids problematic access to user mode
memory in the error handling code path.
criu_checkpoint_bos has its own error handling and cleanup that does not
depend on access to user memory.
In the private data, keep BOs before the remaining objects. This is
necessary to restore things in the correct order as restoring events
depends on the events-page BO being restored first.
Fixes: be072b06c7 ("drm/amdkfd: CRIU export BOs as prime dmabuf objects")
Reported-by: Jann Horn <jannh@google.com>
CC: Rajneesh Bhardwaj <Rajneesh.Bhardwaj@amd.com>
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Reviewed-and-tested-by: Rajneesh Bhardwaj <rajneesh.bhardwaj@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
mutex_unlock before the exit label because all the error code paths that
jump there didn't take that lock. This fixes unbalanced locking errors
in case of restore errors.
Fixes: 40e8a766a7 ("drm/amdkfd: CRIU checkpoint and restore events")
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: Rajneesh Bhardwaj <rajneesh.bhardwaj@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
When the R-Car MIPI DSI driver was added, it was a standalone encoder
driver without any dependency to or from the R-Car DU driver. Commit
957fe62d7d ("drm: rcar-du: Fix DSI enable & disable sequence") then
added a direct call from the DU driver to the MIPI DSI driver, without
updating Kconfig to take the new dependency into account. Fix it the
same way that the LVDS encoder is handled.
Fixes: 957fe62d7d ("drm: rcar-du: Fix DSI enable & disable sequence")
Reported-by: kernel test robot <lkp@intel.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Currently on DG1, which does not have LLC, we hit the below
warning while rebinding an userptr invalidated object.
WARNING: CPU: 4 PID: 13008 at drivers/gpu/drm/i915/gem/i915_gem_pages.c:34 __i915_gem_object_set_pages+0x296/0x2d0 [i915]
...
RIP: 0010:__i915_gem_object_set_pages+0x296/0x2d0 [i915]
...
Call Trace:
<TASK>
i915_gem_userptr_get_pages+0x175/0x1a0 [i915]
____i915_gem_object_get_pages+0x32/0xb0 [i915]
i915_gem_object_userptr_submit_init+0x286/0x470 [i915]
eb_lookup_vmas+0x2ff/0xcf0 [i915]
? __intel_wakeref_get_first+0x55/0xb0 [i915]
i915_gem_do_execbuffer+0x785/0x21d0 [i915]
i915_gem_execbuffer2_ioctl+0xe7/0x3d0 [i915]
We shouldn't be setting the obj->cache_dirty for DGFX,
fix it.
Fixes: d70af57944 ("drm/i915/shmem: ensure flush during swap-in on non-LLC")
Suggested-by: Matthew Auld <matthew.auld@intel.com>
Reported-by: Niranjana Vishwanathapura <niranjana.vishwanathapura@intel.com>
Signed-off-by: Niranjana Vishwanathapura <niranjana.vishwanathapura@intel.com>
Acked-by: Nirmoy Das <nirmoy.das@intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Reviewed-by: Andi Shyti <andi.shyti@linux.intel.com>
Signed-off-by: Andi Shyti <andi.shyti@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221102051416.27327-1-niranjana.vishwanathapura@intel.com
(cherry picked from commit 0aeec60c76)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Currently we are observing mouse cursor stuttering when using
xrandr --scaling=1.2x1.2. X scaling/transformation seems to be
doing fronbuffer rendering. When moving mouse cursor X seems to
perform several invalidates and only one DirtyFB. I.e. it seems
to be assuming updates are sent to panel while drawing is done.
Earlier we were disabling PSR in frontbuffer invalidate call back
(when drawing in X started). PSR was re-enabled in frontbuffer
flush callback (dirtyfb ioctl). This was working fine with X
scaling/transformation. Now we are just enabling continuous full
frame (cff) in PSR invalidate callback. Enabling cff doesn't
trigger any updates. It just configures PSR to send full frame
when updates are sent. I.e. there are no updates on screen before
PSR flush callback is made. X seems to be doing several updates
in frontbuffer before doing dirtyfb ioctl.
Fix this by sending single update on every invalidate callback.
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Mika Kahola <mika.kahola@intel.com>
Fixes: 805f04d42a ("drm/i915/display/psr: Use continuos full frame to handle frontbuffer invalidations")
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/6679
Signed-off-by: Jouni Högander <jouni.hogander@intel.com>
Reported-by: Brian J. Tarricone <brian@tarricone.org>
Tested-by: Brian J. Tarricone <brian@tarricone.org>
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221024054649.31299-1-jouni.hogander@intel.com
(cherry picked from commit d755f89220)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
