Add bluetooth controller nodes and the required brcm,board-type
properties to be able to select the correct firmware to all board
device trees.
Signed-off-by: Sven Peter <sven@svenpeter.dev>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
i.MX fixes for 6.1, part 3:
- Fix a small memory leak in mach-mxs code.
- Correct PCIe pad configuration for imx8mp-evk board.
- Fix ref/tcxo clock frequency property for imx6q-prti6q board.
* tag 'imx-fixes-6.1-3' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: dts: imx6q-prti6q: Fix ref/tcxo-clock-frequency properties
arm64: dts: imx8mp-evk: correct pcie pad settings
ARM: mxs: fix memory leak in mxs_machine_init()
Link: https://lore.kernel.org/r/20221119073812.GQ16229@T480
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
According to RM bit layout, BIT3 and BIT0 are reserved.
8 7 6 5 4 3 2 1 0
PE HYS PUE ODE FSEL X DSE X
Although function is not broken, we should not set reserved bit.
Fixes: d506505000 ("arm64: dts: imx8mp-evk: Add PCIe support")
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
i.MX fixes for 6.1, 2nd round:
- Switch to usb-role-switch for fixing USB device mode on
tqma8mqml-mba8mx board, so that Dual Role is fully functional.
- A series from Marek Vasut to fix dt-schema warning caused by NAND
controller size-cells.
- Fix file permission of imx93-pinfunc header.
- Enable OCOTP clock in soc-imx8m driver to fix a kexec kernel hang
issue.
* tag 'imx-fixes-6.1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
soc: imx8m: Enable OCOTP clock before reading the register
arm64: dts: imx93-pinfunc: drop execution permission
arm64: dts: imx8mn: Fix NAND controller size-cells
arm64: dts: imx8mm: Fix NAND controller size-cells
ARM: dts: imx7: Fix NAND controller size-cells
arm64: dts: imx8mm-tqma8mqml-mba8mx: Fix USB DR
Link: https://lore.kernel.org/r/20221116090402.GA1274@T480
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The Hantro G2 video decoder block sits behind the IOMMU. Without a
reference for the system to properly configure the IOMMU, it will fault
and cause the video decoder to fail.
Add a proper reference to the IOMMU port. The master ID is taken from
the IOMMU fault error message on Linux, and the number seems to match
the order in the user manual's IOMMU diagram.
Fixes: 0baddea60e ("arm64: dts: allwinner: h6: Add Hantro G2 node")
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20221115090644.3602573-3-wenst@chromium.org
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Qualcomm ARM64 DTS fixes for 6.1
This fixes the APCS register region on IPQ8074 to not overlap
with adjacent nodes.
It lists the valid LDO modes on a variety of platforms, as this is not
required by the binding and implementation.
The reference clocks for the two UFS instances on SC8280XP are
corrected, to avoid relying on the state left by most versions of the
bootloader.
A number of issues are corrected with regards to the QMP PHY register
ranges on SC8280XP.
SC7280 gains a missing lpass reset region.
Lastly cluster idle is termporarily disabled on SM8250 to avoid issues
with booting the platform, until the last missing pieces lands.
* tag 'qcom-arm64-fixes-for-6.1' of https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux:
arm64: dts: qcom: sm8250: Disable the not yet supported cluster idle state
arm64: dts: qcom: sc7280: Add the reset reg for lpass audiocc on SC7280
arm64: dts: qcom: sc8280xp: fix UFS PHY serdes size
arm64: dts: qcom: sc8280xp: drop broken DP PHY nodes
arm64: dts: qcom: sc8280xp: fix USB PHY PCS registers
arm64: dts: qcom: sc8280xp: fix USB1 PHY RX1 registers
arm64: dts: qcom: sc8280xp: fix USB0 PHY PCS_MISC registers
arm64: dts: qcom: sc8280xp: correct ref clock for ufs_mem_phy
arm64: dts: qcom: sc8280xp: fix ufs_card_phy ref clock
arm64: dts: qcom: sm8350-hdk: Specify which LDO modes are allowed
arm64: dts: qcom: sm8250-xperia-edo: Specify which LDO modes are allowed
arm64: dts: qcom: sm8150-xperia-kumano: Specify which LDO modes are allowed
arm64: dts: qcom: sc8280xp-crd: Specify which LDO modes are allowed
arm64: dts: qcom: sa8295p-adp: Specify which LDO modes are allowed
arm64: dts: qcom: sa8155p-adp: Specify which LDO modes are allowed
Revert "arm64: dts: qcom: msm8996: add missing TCSR syscon compatible"
arm64: dts: qcom: ipq8074: correct APCS register space size
Link: https://lore.kernel.org/r/20221110040635.795921-1-andersson@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Ths PMIC's interrupt line is tied to GPIO0_A3. This is described
correctly for the pinmux setting, but incorrectly for the interrupt.
Correct the interrupt setting so that interrupts from the PMIC get
delivered.
Fixes: dcc8c66bef ("arm64: dts: rockchip: add Pine64 Quartz64-B device tree")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Peter Geis <pgwipeout@gmail.com>
Link: https://lore.kernel.org/r/20221106161513.4140-1-wens@kernel.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Similar to TX Wireless Ethernet Dispatch, introduce RX Wireless Ethernet
Dispatch to offload traffic received by the wlan interface to lan/wan
one.
Co-developed-by: Sujuan Chen <sujuan.chen@mediatek.com>
Signed-off-by: Sujuan Chen <sujuan.chen@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The NAND controller size-cells should be 0 per DT bindings.
Fix the following warning produces by DT bindings check:
"
nand-controller@33002000: #size-cells:0:0: 0 was expected
nand-controller@33002000: Unevaluated properties are not allowed ('#address-cells', '#size-cells' were unexpected)
"
Fixes: 6c3debcbae ("arm64: dts: freescale: Add i.MX8MN dtsi support")
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The NAND controller size-cells should be 0 per DT bindings.
Fix the following warning produces by DT bindings check:
"
nand-controller@33002000: #size-cells:0:0: 0 was expected
nand-controller@33002000: Unevaluated properties are not allowed ('#address-cells', '#size-cells' were unexpected)
"
Fix the missing space in node name too.
Fixes: a05ea40eb3 ("arm64: dts: imx: Add i.mx8mm dtsi support")
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Using extcon USB host mode works properly on DR interface, e.g.
enabling/disabling VBUS. But USB device mode is not working.
Fix this by switching to usb-role-switch instead.
Fixes: dfcd1b6f76 ("arm64: dts: freescale: add initial device tree for TQMa8MQML with i.MX8MM")
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Armv8 Juno fix for v6.1
Just a single fix to add the missing critical points in the thermal
zones that has been mandatory in the binding but was enforced in the
code recently.
* tag 'juno-fix-6.1' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux:
arm64: dts: juno: Add thermal critical trip points
Link: https://lore.kernel.org/r/20221102140156.2758137-1-sudeep.holla@arm.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Up until now, the external MDIO controller frequency values relied
either on the default ones out of reset or on those setup by u-boot.
Let's just properly specify the MDC frequency in the DTS so that even
without u-boot's intervention Linux can drive the MDIO bus.
Fixes: 0420dde30a ("arm64: dts: ls208xa: add the external MDIO nodes")
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Up until now, the external MDIO controller frequency values relied
either on the default ones out of reset or on those setup by u-boot.
Let's just properly specify the MDC frequency in the DTS so that even
without u-boot's intervention Linux can drive the MDIO bus.
Fixes: bbe75af7b0 ("arm64: dts: ls1088a: add external MDIO device nodes")
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Up until now, the external MDIO controller frequency values relied
either on the default ones out of reset or on those setup by u-boot.
Let's just properly specify the MDC frequency in the DTS so that even
without u-boot's intervention Linux can drive the MDIO bus.
Fixes: 6e1b8fae89 ("arm64: dts: lx2160a: add emdio1 node")
Fixes: 5705b9dcda ("arm64: dts: lx2160a: add emdio2 node")
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Per binding doc, interrupt names should be tx and rx.
Fixes: 0dfb380d24 ("arm64: dts: imx93: add s4 mu node")
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Per bindings/mmc/fsl-imx-esdhc.yaml, the clock order is ipg, ahb, per,
otherwise warning: "
mmc@5b020000: clock-names:1: 'ahb' was expected
mmc@5b020000: clock-names:2: 'per' was expected "
Fixes: 16c4ea7501 ("arm64: dts: imx8: switch to new lpcg clock binding")
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
pgc_otg1 is actual the power domain of usb PHY, usb controller
is in hsio power domain, and pgc_otg1 is required to be powered
up to detect usb remote wakeup, so move the pgc_otg1 power domain
to the usb phy node.
Fixes: ea2b5af58a ("arm64: dts: imx8mn: put USB controller into power-domains")
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
pgc_otg1 is an independent power domain of hsio, it's for usb phy,
so remove hsio power domain from its node.
Fixes: 8b8ebec673 ("arm64: dts: imx8mn: add GPC node")
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
pgc_otg1/2 is actual the power domain of usb PHY, usb controller
is in hsio power domain, and pgc_otg1/2 is required to be powered
up to detect usb remote wakeup, so move the pgc_otg1/2 power domain
to the usb phy node.
Fixes: 01df28d808 ("arm64: dts: imx8mm: put USB controllers into power-domains")
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
pgc_otg1/2 are independent power domain of hsio, they for usb phy,
so remove hsio power domain dependency from its node.
Fixes: d39d4bb153 ("arm64: dts: imx8mm: add GPC node")
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The GPIO signaling ctrl_sleep_moci is currently handled as a gpio hog.
But the gpio-hog node is made a child of the wrong gpio controller.
Move it to the node representing gpio4 so that it actually works.
Without this carrier board components jumpered to use the signal are
unconditionally switched off.
Fixes: a39ed23bdf ("arm64: dts: freescale: add initial support for verdin imx8m plus")
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
To support the deeper cluster idle state for sm8250 platforms, some
additional synchronization is needed between the rpmh-rsc device and the
CPU cluster PM domain. Until that is supported, let's disable the cluster
idle state.
This fixes a problem that has been reported for the Qcom RB5 platform (see
below), but most likely other sm8250 platforms suffers from similar issues,
so let's make the fix generic for sm8250.
vreg_l11c_3p3: failed to enable: -ETIMEDOUT
qcom-rpmh-regulator 18200000.rsc:pm8150l-rpmh-regulators: ldo11: devm_regulator_register() failed, ret=-110
qcom-rpmh-regulator: probe of 18200000.rsc:pm8150l-rpmh-regulators failed with error -110
Reported-by: Amit Pundir <amit.pundir@linaro.org>
Fixes: 32bc936d73 ("arm64: dts: qcom: sm8250: Add cpuidle states")
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Amit Pundir <amit.pundir@linaro.org>
Reviewed-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221027115745.240516-1-ulf.hansson@linaro.org
Enable CPLD_Dn pull down resistor instead of pull up to avoid
intefering with CPLD power off functionality.
Fixes: 510c527b4f ("arm64: dts: imx8mm: Add i.MX8M Mini Toradex Verdin based Menlo board")
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Now that we actually read registers from QSGMII PCSs, it's important
that we have the correct address (instead of hoping that we're the MAC
with all the QSGMII PCSs on its bus). This adds nodes for the QSGMII
PCSs. The exact mapping of QSGMII to MACs depends on the SoC.
Since the first QSGMII PCSs share an address with the SGMII and XFI
PCSs, we only add new nodes for PCSs 2-4. This avoids address conflicts
on the bus.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update the PP2 ethernet ports subnodes' names to match
schema enforced by the marvell,pp2.yaml contents.
Add new required properties ('reg') which contains information
about the port ID, keeping 'port-id' ones for backward
compatibility.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The DP PHY register layout of the current binding do not apply to the
newer USB4/USB3/DP PHY which uses a different register layout entirely.
Drop the DP PHY subnodes until the binding has been updated to prevent
the driver from corrupting unrelated registers.
Note that this is also needed in order to not break USB with an upcoming
PHY driver change that checks for overlapping register regions.
Fixes: 152d1faf1e ("arm64: dts: qcom: add SC8280XP platform")
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220919094454.1574-5-johan+linaro@kernel.org
The first UFS host controller fails to start on the SA8540P automotive
board (QDrive3) due to the following errors:
ufshcd-qcom 1d84000.ufs: ufshcd_query_flag: Sending flag query for idn 18 failed, err = 253
ufshcd-qcom 1d84000.ufs: ufshcd_query_flag: Sending flag query for idn 18 failed, err = 253
ufshcd-qcom 1d84000.ufs: ufshcd_query_flag: Sending flag query for idn 18 failed, err = 253
ufshcd-qcom 1d84000.ufs: ufshcd_query_flag_retry: query attribute, opcode 5, idn 18, failed
with error 253 after 3 retries
The system eventually fails to boot with the warning:
gcc_ufs_phy_axi_clk status stuck at 'off'
This issue can be worked around by adding clk_ignore_unused to the
kernel command line since the system firmware sets up this clock for us.
Let's fix this issue by updating the ref clock on ufs_mem_phy. Note
that the downstream MSM 5.4 sources list this as ref_clk_parent. With
this patch, the SA8540P is able to be booted without clk_ignore_unused.
Signed-off-by: Brian Masney <bmasney@redhat.com>
Fixes: 152d1faf1e ("arm64: dts: qcom: add SC8280XP platform")
Tested-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221006145529.755521-1-bmasney@redhat.com
The GCC_UFS_REF_CLKREF_CLK must be enabled or the second UFS controller
fails to enumerate on sa8295p-adp.
Note that the vendor kernel enables both GCC_UFS_REF_CLKREF_CLK and
GCC_UFS_1_CARD_CLKREF_CLK and it is possible that the former should be
modelled as a parent of the latter. The clock driver also has a
GCC_UFS_CARD_CLKREF_CLK clock which the firmware appears to enable on
the ADP.
The usual lack of documentation for Qualcomm SoCs makes this a highly
annoying guessing game, but as the second controller works on the ADP
without either card reference clock enabled, only enable
GCC_UFS_REF_CLKREF_CLK for now.
Fixes: 152d1faf1e ("arm64: dts: qcom: add SC8280XP platform")
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Reviewed-by: Brian Masney <bmasney@redhat.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221005143305.388-1-johan+linaro@kernel.org
