If during validation of the firmware download the data doesn't match what is
expected out of the chip, this calls for a firmware download failure and a
retry.
Free the SKB which collects response during such scenarios.
Signed-off-by: Pavan Savoy <pavan_savoy@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When the line discipline install fails for reasons such as missing user-space
UIM or broken communication between UIM and ST driver, then the ST
attempts/retries to request for ldisc installation again.
Signed-off-by: Pavan Savoy <pavan_savoy@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
download firmware behaves differently at different times, when logs are
enabled and the system is loaded, the wait_for_completion is able to wait for
every send, However during other times the wait does not happen.
So, for reliability reinitializing the completion before every send, makes
sure the wait happens for every send.
Signed-off-by: Pavan Savoy <pavan_savoy@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Texas Instrument's shared transport driver interpret incoming data from the
UART based on the various protocol drivers registered to the driver such as
btwilink driver or FM or GPS driver which provide logical channel IDs.
In case of bad-behavior from chip such as HCI Event response for a GPS command
or a HCI Event (h/w error event) for a FM response & In case of bad-behavior
from UART driver such as dropping data bytes a fail-safe is required to avoid
kernel panic.
Signed-off-by: Pavan Savoy <pavan_savoy@ti.com>
Signed-off-by: Vijay Badawadagi <bvijay@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
After the version information has been read, the completion which assists in
wait_for_completion during the firmware send/wait sequence is being re-used
and hence this needs to be re-initialised for fool proof firmware download
retries.
Signed-off-by: Pavan Savoy <pavan_savoy@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Certain platform specific or Host-WiLink Interface specific actions would be
required to be taken when the chip is being enabled and after the chip is
disabled such as configuration of the mux modes for the GPIO of host connected
to the nshutdown of the chip or relinquishing UART after the chip is disabled.
Similar actions can also be taken when the chip is in deep sleep or when the
chip is awake. Performance enhancements such as configuring the host to run
faster when chip is awake and slower when chip is asleep can also be made
here.
Signed-off-by: Pavan Savoy <pavan_savoy@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Previously the private data of each protocol registered to use ST was
used to determine whether the protocol was registered to use shared
transport or otherwise.
However, now a flag is_registered is maintained to identify whether a
protocol intends to use ST.
Upon closing of the UART the error message relevant to this lack of
un-registration was misleading and this patch fixes that.
Signed-off-by: Pavan Savoy <pavan_savoy@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
devres_release_all and devres_release_group both aquire the lock
&dev->devres_lock but the release of that lock is done in release_nodes.
This results in sparse noise about context imbalance.
Add a lock annotation to release_nodes to quiet this noise.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
allmodconfig compile fails on s390 because of the new PTI driver:
drivers/misc/pti.c:407:3: error: implicit declaration of function 'pci_iounmap'
drivers/misc/pti.c:410:3: error: implicit declaration of function 'pci_release_region'
Add a 'depends on PCI' statement so it doesn't get compiled.
Cc: J Freyensee <james_p_freyensee@linux.intel.com>
Signed-off-by: Tracey Dent <tdent48227@gmail.com>
Acked-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Sergei Trofimovich <slyfox@gentoo.org>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This fixes the following section mismatch issue:
WARNING: vmlinux.o(.text+0x1192bf): Section mismatch in reference from the function devtmpfsd() to the variable .init.data:setup_done
The function devtmpfsd() references the variable __initdata setup_done.
This is often because devtmpfsd lacks a __initdata annotation or the annotation of setup_done is wrong.
WARNING: vmlinux.o(.text+0x119342): Section mismatch in reference from the function devtmpfsd() to the variable .init.data:setup_done
The function devtmpfsd() references the variable __initdata setup_done.
This is often because devtmpfsd lacks a __initdata annotation or the annotation of setup_done is wrong.
Signed-off-by: Arnaud Lacombe <lacombar@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Warning(drivers/base/platform.c:50): No description found for parameter 'pdev'
Warning(drivers/base/platform.c:50): Excess function parameter 'dev' description in 'arch_setup_pdev_archdata'
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Modify function parameter type to match expected type. Fixes a
build warning:
drivers/firmware/google/gsmi.c:473: warning: initialization from incompatible pointer type
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Cc: Mike Waychison <mikew@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Commit d006199e72a9 ("serial: sh-sci: Regtype probing doesn't need to be
fatal.") made sci_init_single() return when sci_probe_regmap() succeeds,
although it should return when sci_probe_regmap() fails. This causes
systems using the serial sh-sci driver to crash during boot.
Fix the problem by using the right return condition.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
net: Compute protocol sequence numbers and fragment IDs using MD5.
crypto: Move md5_transform to lib/md5.c
Computers have become a lot faster since we compromised on the
partial MD4 hash which we use currently for performance reasons.
MD5 is a much safer choice, and is inline with both RFC1948 and
other ISS generators (OpenBSD, Solaris, etc.)
Furthermore, only having 24-bits of the sequence number be truly
unpredictable is a very serious limitation. So the periodic
regeneration and 8-bit counter have been removed. We compute and
use a full 32-bit sequence number.
For ipv6, DCCP was found to use a 32-bit truncated initial sequence
number (it needs 43-bits) and that is fixed here as well.
Reported-by: Dan Kaminsky <dan@doxpara.com>
Tested-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'stable/bug.fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen/trace: Fix compile error when CONFIG_XEN_PRIVILEGED_GUEST is not set
xen: Fix misleading WARN message at xen_release_chunk
xen: Fix printk() format in xen/setup.c
xen/tracing: it looks like we wanted CONFIG_FTRACE
xen/self-balloon: Add dependency on tmem.
xen/balloon: Fix compile errors - missing header files.
xen/grant: Fix compile warning.
xen/pciback: remove duplicated #include
Two additional savage4 variants were added, but the S3_SAVAGE4_SERIES
macro was incompletely modified, resulting in a false positive detection
of a savage4 card regardless of which savage card is actually present.
For non-savage4 series cards, such as a Savage/IX-MV card, this results
in garbled video and/or a hard-hang at boot time. Fix this by changing
an '||' to an '&&' in the S3_SAVAGE4_SERIES macro.
Signed-off-by: John P. Stanley <jpsinthemix@verizon.net>
Reviewed-by: Tormod Volden <debian.tormod@gmail.com>
[ The macros have incomplete parenthesis too, but whatever .. -Linus ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently the use of pm_runtime_put_sync() is not safe from
interrupts-disabled context because rpm_idle() will release the
spinlock and enable interrupts for the idle callbacks. This enables
interrupts during a time where interrupts were expected to be
disabled, and can have strange side effects on drivers that expected
interrupts to be disabled.
This is not a bug since the documentation clearly states that only
_put_sync_suspend() is safe in IRQ-safe mode.
However, pm_runtime_put_sync() could be made safe when in IRQ-safe
mode by releasing the spinlock but not re-enabling interrupts, which
is what this patch aims to do.
Problem was found when using some buggy drivers that set
pm_runtime_irq_safe() and used _put_sync() in interrupts-disabled
context.
Reported-by: Colin Cross <ccross@google.com>
Tested-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
The local variable ret is defined twice in pm_genpd_poweron(), which
causes this function to always return 0, even if the PM domain's
.power_on() callback fails, in which case an error code should be
returned.
Remove the wrong second definition of ret and additionally remove an
unnecessary definition of wait from pm_genpd_poweron().
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
It seems that aliases shouldn't contain spaces, as
module-init-tools uses them as delimeters in module.alias file
Signed-off-by: Anton V. Boyarshinov <boyarsh@altlinux.org>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
In the case of ideapad_backlight_init() failure,
we need to free the resources allocated by ideapad_input_init().
Aslo drop __devexit annotation for ideapad_input_exit() because
we also call it in ideapad_acpi_add() error path.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
When enabling turbo, we need to set both the TDC and TDP bits. IIRC
only the TDC one actually matters, but fix it up anyway since the
current code is confusing.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Some samsung latop of the N150/N2{10,20,30} serie are badly detected by the samsung-laptop platform driver, see bug # 36082.
It appears that N230 identifies itself as N150/N210/N220/N230 whereas the other identify themselves as N150/N210/220.
This patch attemtp fix#36082 allowing correct identification for all the said netbook model.
Reported-by: Daniel Eklöf <daniel@ekloef.se>
Signed-off-by: Thomas Courbon <thcourbon@gmail.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
We only care about if there is any successful match from the dmi table
or no match at all, we can make dmi_check_system return immediately if
we have a successful match instead of iterate thorough the whole table.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
This adds backlight control on the Samsung Q10 laptop, which does not support
the SABI interface. Also tested successfully on the Dell Latitude X200.
Signed-off-by: Frederick van der Wyck <fvanderwyck@gmail.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
The memory for td_info which is allocated in initialize_sensor()
should be properly kfreed in mid_thermal_probe() error patch and
mid_thermal_remove().
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
The N510 benefits from this code as well. Below is a patch to include support.
Signed-off-by: Jouke Witteveen <j.witteveen@gmail.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
The T101MT Home/Express Gate key autorepeats in hardware, but
sparse-keymap does not support hardware autorepeat. Enable the
input core's software autorepeat to emulate the hardware behavior.
Normal hotkeys are autoreleased, so the behavior of these keys
will not be affected.
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Signed-off-by: Corentin Chary <corentin.chary@gmail.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Pavan Savoy