[airlied: just added some comments on how to reenable]
On-list because the cat is out of the bag and we're clearly not good
enough to figure this out in private. The story thus far:
5e28b7b944 ("drm: Set old handle to NULL before prime swap in
change_handle") tried to fix a race condition between the gem_close and
gem_change_handle ioctls, but got a few things wrong:
- There's a confusion with the local variable handle, which is actually
the new handle, and so the two-stage trick was actually applied to the
wrong idr slot. 7164d78559 ("drm/gem: fix race between
change_handle and handle_delete") tried to fix that by adding yet
another code block, but forgot to add the error handling. Which meant
we now have two paths, both kinda wrong.
- dc366607c4 ("drm: Replace old pointer to new idr") tried to apply
another fix, but inconsistently, again because of the handle confusion
- this would be the right fix (kinda, somewhat, it's a mess) if we'd
do the two-stage approach for the new handle. Except that wasn't the
intent of the original fix.
We also didn't have an igt merged for the original ioctl, which is a big
no-go. This was attempted to address off-list in the original bugfix,
and amd QA people claimed the bug was fixed now. Very clearly that's not
the case. Here's my attempt to sort this out:
- Rename the local variable to new_handle, the old aliasing with
args->handle is just too dangerously confusing.
- Merge the gem obj lookup with the two-stage idr_replace so that we
avoid getting ourselves confused there.
- This means we don't have a surplus temporary reference anymore, only
an inherited from the idr. A concurrent gem_close on the new_handle
could steal that. Fix that with the same two-stage approach
create_tail uses. This is a bit overkill as documented in the comment,
but I also don't trust my ability to understand this all correctly, so
go with the established pattern we have from other ioctls instead for
maximum paranoia.
- Adjust error paths. I've tried to make the error and success paths
common, because they are identical except for which handle is removed
and on which we call idr_replace to (re)install the object again. But
that made things messier to read, so I've left it at the more verbose
version, which unfortunately hides the symmetry in the entire code
flow a bit.
- While at it, also replace the 7 space indent with 1 tab.
And finally, because I flat out don't trust my abilities here at all
anymore:
- Disable the ioctl until we have the igt situation and everything else
sorted out on-list and with full consensus.
v2:
Sashiko noticed that I didn't handle the error path for idr_replace
correctly, it must be checked with IS_ERR_OR_NULL like in
gem_handle_delete. So yeah, definitely should just the existing paths
1:1 because this is endless amounts of tricky.
Also add the Fixes: line for the original ioctl, I forgot that too.
Reported-by: DARKNAVY (@DarkNavyOrg) <vr@darknavy.com>
Signed-off-by: Simona Vetter <simona.vetter@ffwll.ch>
Fixes: dc366607c4 ("drm: Replace old pointer to new idr")
Cc: syzbot+d7c9eed171647e421013@syzkaller.appspotmail.com
Cc: stable@vger.kernel.org
Cc: Edward Adam Davis <eadavis@qq.com>
Cc: Dave Airlie <airlied@redhat.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Maxime Ripard <mripard@kernel.org>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Fixes: 5e28b7b944 ("drm: Set old handle to NULL before prime swap in change_handle")
Cc: David Francis <David.Francis@amd.com>
Cc: Puttimet Thammasaeng <pwn8official@gmail.com>
Cc: Christian Koenig <Christian.Koenig@amd.com>
Fixes: 7164d78559 ("drm/gem: fix race between change_handle and handle_delete")
Cc: Zhenghang Xiao <kipreyyy@gmail.com>
Fixes: 5e28b7b944 ("drm: Set old handle to NULL before prime swap in change_handle")
Reviewed-by: David Francis <David.Francis@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Link: https://patch.msgid.link/20260604194437.1725314-1-simona.vetter@ffwll.ch
Short summary of fixes pull:
dumb-buffer:
- remove strict limits on buffer geometry
ethosu:
- reject unsupported NPU_OP_RESIZE
- fix index of IFM region
- fix weight index
- fix overflows in DMA-size calculations
- reject DMA commands with uninitialized length
- fix OOB write in ethosu_gem_cmdstream_copy_and_validate
imx:
- fix kernel-doc warnings
ivpu:
- add overflow checks in firmware handling and get_info_ioctl
v3d:
- wait for pending L2T flush before cleaning caches
- fix leak of vaddr
- skip CSD when it has zeroed workgroups
- fix ref counting in performance monitoring
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patch.msgid.link/20260605072602.GA268798@linux.fritz.box
This reverts commit 40d2f58209.
Removing the try_vesa_interface gate caused a backlight regression on
panels whose VBT correctly reports INTEL_BACKLIGHT_DISPLAY_DDI and whose
PWM path is the actual backlight control, but whose DPCD optimistically
advertises DP_EDP_BACKLIGHT_AUX_ENABLE_CAP / _BRIGHTNESS_AUX_SET_CAP.
After the commit such panels silently bind to the VESA AUX backlight
funcs; AUX writes complete but the panel ignores them, leaving
brightness stuck (no-op backlight). Observed on at least KBL and TGL
eDP setups.
Signed-off-by: Suraj Kandpal <suraj.kandpal@intel.com>
Reviewed-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Link: https://patch.msgid.link/20260517024709.1016121-1-suraj.kandpal@intel.com
(cherry picked from commit f30fddb440)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@igalia.com>
In the SET_GLOBAL ioctl, v3d_perfmon_find() bumps the reference count on
the perfmon it returns, but v3d_perfmon_set_global_ioctl() and
v3d_perfmon_delete() fail to release that reference on several paths:
1. v3d_perfmon_set_global_ioctl() leaks the reference on its error
paths.
2. CLEAR_GLOBAL leaks both the find reference and the reference
previously stashed in v3d->global_perfmon by the SET_GLOBAL ioctl
that configured it.
3. Destroying a perfmon that is the current global perfmon leaks the
reference stashed by the SET_GLOBAL ioctl.
Release each of these references explicitly.
Cc: stable@vger.kernel.org
Fixes: c6eabbab35 ("drm/v3d: Add DRM_IOCTL_V3D_PERFMON_SET_GLOBAL")
Reviewed-by: Iago Toral Quiroga <itoral@igalia.com>
Link: https://patch.msgid.link/20260531-v3d-perfmon-lifetime-v2-1-60ed4485a203@igalia.com
Signed-off-by: Maíra Canal <mcanal@igalia.com>
In the schedule-disable done path for suspend, we
signal the suspend fence before clearing pending_disable.
That wakeup can let suspend_wait complete and resume be queued
immediately. The resume path may then reach enable_scheduling()
while pending_disable is still set and hit the
!exec_queue_pending_disable(q) assertion.
Fix this by clearing pending_disable before signaling
the suspend fence, so any resumed transition observes a
consistent state.
Fixes: 87651f31ae ("drm/xe/guc_submit: fix race around suspend_pending")
Cc: stable@vger.kernel.org # v7.0+
Signed-off-by: Tangudu Tilak Tirumalesh <tilak.tirumalesh.tangudu@intel.com>
Reviewed-by: Thomas Hellstrom <thomas.hellstrom@linux.intel.com>
Signed-off-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Link: https://patch.msgid.link/20260603065217.3131066-3-tilak.tirumalesh.tangudu@intel.com
(cherry picked from commit 4b1ae138b0e103d753773956a84eebc2edbf62c4)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
This reverts commit 8533051ce9.
The idle-skip optimization bypasses GuC suspend, so the GPU may not
perform the context switch that flushes TLB entries for invalidated
userptr VMAs. In LR/preempt-fence VM mode, this can lead to missed TLB
invalidation and page faults during userptr invalidation tests.
Restore unconditional schedule toggling on suspend so the context-switch
TLB flush is always performed.
This optimization will be reintroduced with a fix that does not skip
suspend in LR/preempt-fence VM mode.
Fixes: 8533051ce9 ("drm/xe: Skip exec queue schedule toggle if queue is idle during suspend")
Cc: stable@vger.kernel.org # v7.0+
Suggested-by: Thomas Hellstrom <thomas.hellstrom@linux.intel.com>
Signed-off-by: Tangudu Tilak Tirumalesh <tilak.tirumalesh.tangudu@intel.com>
Reviewed-by: Thomas Hellstrom <thomas.hellstrom@linux.intel.com>
Signed-off-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Link: https://patch.msgid.link/20260603065217.3131066-2-tilak.tirumalesh.tangudu@intel.com
(cherry picked from commit 6a1e7934d9a6cf46aecae00a99c2603d1295e170)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
In smu_v14_0_0_set_soft_freq_limited_range(), the gfxclk floor is
programmed via SetHardMinGfxClk together with SetSoftMaxGfxClk. Under
power_dpm_force_performance_level=high this pins HardMin to peak gfxclk.
In PMFW arbitration HardMin has higher priority than SoftMax, so the
firmware thermal/PPT throttler cannot clamp gfxclk via SoftMax once
HardMin is set to peak. Replace SetHardMinGfxClk with SetSoftMinGfxclk
so the driver still requests peak performance but the firmware
throttler retains the ability to clamp gfxclk under thermal/PPT
pressure. SoftMax handling is unchanged and no other clock domains
are affected.
Signed-off-by: Priya Hosur <Priya.Hosur@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 3ea273267f)
Cc: stable@vger.kernel.org
When mapping VRAM pages into the GART page table,
amdgpu_gart_map_vram_range() assumes that the system page size is the
same as the GPU page size.
On systems with non-4K page sizes, multiple GPU pages can exist within
a single CPU page. As a result, the mappings are created incorrectly
because fewer page table entries are programmed than required.
Fix this by programming the mappings correctly for non-4K page size
systems.
Fixes: 237d623ae6 ("drm/amdgpu/gart: Add helper to bind VRAM pages (v2)")
Reviewed-by: Timur Kristóf <timur.kristof@gmail.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Donet Tom <donettom@linux.ibm.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit a8f0bc2238)
Cc: stable@vger.kernel.org
In case when queue_create fails and mqd has already been
allocated and hence wptr_obj is not cleaned up.
So moving that cleanup part to mqd_destroy so it takes
care of all the cases of clean up and during tear down of
the queue.
Signed-off-by: Sunil Khatri <sunil.khatri@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 43355f62cd)
Use find_next_zero_bit() to locate the next free seq slot bit
instead of the current walk, for more efficient bitmap scanning.
Signed-off-by: Prike Liang <Prike.Liang@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit ff905a9b62)
Mesa userqueues free does not wait for the free to complete and go ahead
in unmapping the vital bos while kernel is still in queue free and
corresponding cleanup.
So ideally we don't need the logging for that and hence remove the warn
message as this is expected behaviour and functionally, we are making
sure to wait for the required fences before unmap.
Signed-off-by: Sunil Khatri <sunil.khatri@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 758a868043)
The v11 MQD manager incorrectly assigned the CP-compute variants of
checkpoint_mqd/restore_mqd for KFD_MQD_TYPE_SDMA queues. These functions
use sizeof(struct v11_compute_mqd) (2048 bytes) instead of sizeof(struct
v11_sdma_mqd) (512 bytes), causing a 1536-byte overflow.
During CRIU checkpoint of an SDMA queue on Navi3x:
- checkpoint_mqd() reads 2048 bytes from a 512-byte SDMA MQD buffer,
leaking 1536 bytes of adjacent GTT memory to userspace
During CRIU restore:
- restore_mqd() writes 2048 bytes into a 512-byte SDMA MQD buffer,
corrupting 1536 bytes of adjacent GTT memory (often the ring buffer
or neighboring MQDs)
This is a copy-paste regression unique to v11. All other ASIC backends
(cik, vi, v9, v10, v12) correctly use the SDMA-specific variants.
Add checkpoint_mqd_sdma() and restore_mqd_sdma() functions that properly
handle the smaller v11_sdma_mqd structure, matching the pattern used in
other MQD managers.
Fixes: cc009e613d ("drm/amdkfd: Add KFD support for soc21 v3")
Assisted-by: Claude:Sonnet 4-5
Signed-off-by: Andrew Martin <andrew.martin@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 6fa41db7ff)
Cc: stable@vger.kernel.org
When usr_queue_id_array is NULL and num_queues is non-zero,
get_queue_ids() returns NULL. The callers check only IS_ERR() on the
return value; since IS_ERR(NULL) == false the check passes, and
suspend_queues() calls q_array_invalidate() which immediately
dereferences NULL while iterating num_queues times.
Userspace can trigger this via kfd_ioctl_set_debug_trap() by supplying
num_queues > 0 with a zero queue_array_ptr, causing a kernel panic.
A NULL usr_queue_id_array with num_queues == 0 is a legitimate no-op
(q_array_invalidate never executes, and resume_queues already guards
all queue_ids dereferences behind a NULL check). Return ERR_PTR(-EINVAL)
only when num_queues is non-zero and the pointer is absent; both callers
already propagate IS_ERR() returns correctly to userspace.
Fixes: a70a93fa56 ("drm/amdkfd: add debug suspend and resume process queues operation")
Signed-off-by: Muhammad Bilal <meatuni001@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit f165a82cdf)
Cc: stable@vger.kernel.org
Problem:
While developing the amd_close_race IGT test (which intentionally triggers
execute permission faults by removing VM_PAGE_EXECUTABLE from GPU page table
entries), we discovered that on Navi10 (GFX 10.1.x) these faults produce
zero diagnostic output. The GPU simply hangs silently for ~10s until the
scheduler timeout fires. There is no way to distinguish an execute
permission fault from any other type of GPU hang.
Root cause:
GFX 10.1.x defaults to noretry=0, which sets
RETRY_PERMISSION_OR_INVALID_PAGE_FAULT=1 in the GFXHUB UTCL2 registers
(gfxhub_v2_0.c line 313). With this bit set, permission faults (valid PTE,
wrong R/W/X bits) are handled entirely within the UTCL1/UTCL2 hardware
loop: UTCL2 returns an XNACK to UTCL1, and UTCL1 re-requests the
translation indefinitely, expecting software to eventually fix the
permission bits (as happens in SVM/HMM recovery). No interrupt of any kind
reaches the IH ring.
This is different from invalid-page faults (V=0) which DO generate a retry
fault interrupt that the driver can escalate to a no-retry fault. Permission
faults with valid PTEs loop silently forever in hardware.
GFX 10.3+ already defaults to noretry=1, which makes permission faults
generate immediate L2 protection fault interrupts. GFX 10.1.x was
inadvertently left out of this default.
Fix:
Change the noretry=1 threshold from IP_VERSION(10, 3, 0) to
IP_VERSION(10, 1, 0) in amdgpu_gmc_noretry_set(). This is a one-line
change that aligns GFX 10.1.x behavior with GFX 10.3+ and all newer
generations.
With noretry=1, the existing non-retry fault handler
(gmc_v10_0_process_interrupt) already decodes and prints the full
GCVM_L2_PROTECTION_FAULT_STATUS register including PERMISSION_FAULTS,
faulting address, VMID, PASID, and process name. No additional logging
code is needed — the fix is purely routing permission faults to the
existing, fully-capable non-retry interrupt handler.
v2: Dropped GFX10-specific logging from gmc_v10_0.c and
kfd_int_process_v10.c (Felix Kuehling). v1 added logging in the retry
fault handler, but with noretry=1 permission faults take the non-retry
path — the v1 retry handler code was dead and would never execute.
Tested on Navi10 (GFX 10.1.10):
- Execute permission faults now produce immediate, clear output:
[gfxhub] page fault (src_id:0 ring:64 vmid:4 pasid:592)
Process amd_close_race pid 13380 thread amd_close_race pid 13384
in page at address 0x40001000 from client 0x1b (UTCL2)
GCVM_L2_PROTECTION_FAULT_STATUS:0x00700881
PERMISSION_FAULTS: 0x8
- No regressions with properly-mapped GPU workloads
Cc: Christian Koenig <christian.koenig@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Felix Kuehling <felix.kuehling@amd.com>
Signed-off-by: Vitaly Prosyak <vitaly.prosyak@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit eb21edd24c)
Cc: stable@vger.kernel.org
When the fault stop mode isn't AMDGPU_VM_FAULT_STOP_ALWAYS,
these bits should be programmed to 0.
Program CRASH_ON_NO_RETRY_FAULT and CRASH_ON_RETRY_FAULT
always, to make sure to clear the bits when we don't want
to crash.
Signed-off-by: Timur Kristóf <timur.kristof@gmail.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit d0cd99e730)
For PTE creation use asic specific physical page base address mask
v2: Change variable name from pa_mask to pte_addr_mask
Signed-off-by: Harish Kasiviswanathan <Harish.Kasiviswanathan@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 2ea9898859)
SMU messages may use fewer arguments than the available argument registers,
the previous code only wrote used registers and left the rest unchanged,
so stale values from a prior message could persist.
Write all argument registers for each message and zero the unused tail
to keep command arguments deterministic and avoid unintended carry-over.
Signed-off-by: Yang Wang <kevinyang.wang@amd.com>
Reviewed-by: Asad Kamal <asad.kamal@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit e03b635f61)
smu_v13_0_0_get_power_limit() and smu_v13_0_7_get_power_limit() mix
runtime power_limit with PP table limits when reporting default/min/max.
When current power limit query succeeds, default_power_limit was set to the
runtime value instead of the PP table default, and min/max could be derived
from inconsistent bases (MsgLimits/runtime), leading to incorrect cap info.
Use SocketPowerLimitAc/Dc as the PP default base (pp_limit), keep
current_power_limit as runtime value, and derive min/max from pp_limit with
OD percentages.
Closes: https://gitlab.freedesktop.org/drm/amd/-/work_items/5227
Signed-off-by: Yang Wang <kevinyang.wang@amd.com>
Reviewed-by: Kenneth Feng <kenneth.feng@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 1eaf26db95)
Cc: stable@vger.kernel.org
On SMU v13.0.10, sending PrepareMp1ForUnload with the default
parameter may leave the device in an inaccessible state. This can
affect runtime power management and partial PnP flows.
e.g: kexec, driver unload, boco/d3cold.
Pass the required workaround parameter 0x55, when preparing MP1 for
unload on SMU v13.0.10, keep the existing behavior for other SMU
versions.
Closes: https://gitlab.freedesktop.org/drm/amd/-/work_items/5133
Signed-off-by: Yang Wang <kevinyang.wang@amd.com>
Reviewed-by: Kenneth Feng <kenneth.feng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 4e8ee1afee)
Cc: stable@vger.kernel.org
If the driver only preempts queues, there can still be inflight waves,
pending dispatch state, or resume/redispatch possibility tied to the
same queue. Then the VM/TTM side may proceed to move/unmap queue related
BOs during evicting userq objects while shader TCP clients still need to
access them.
So for eviction, unmap is safer because it makes the queue nonrunnable
before memory backing is invalidated. Meanwhile, for a idle queue it's
more sutiable for unmapping it rather preempt and unmapping also can
save more processing time than preempt.
Signed-off-by: Prike Liang <Prike.Liang@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit d87c9d8672)
wait_on_destroy_queue() drops locks to wait for queue resume, allowing
a concurrent destroy to free the queue. Use is_being_destroyed flag to
serialize destruction.
Reviewed-by: Amir Shetaia <Amir.Shetaia@amd.com>
Signed-off-by: Alysa Liu <Alysa.Liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit ac081deaf1)
[Why & How]
All record-chain walk loops in bios_parser.c and bios_parser2.c use
for(;;) and only terminate on a 0xFF record_type sentinel or zero
record_size. A malformed VBIOS image missing the terminator record
causes unbounded iteration at probe time, potentially hundreds of
thousands of iterations with record_size=1. In the final iterations
near the BIOS image boundary, struct casts beyond the 2-byte header
validated by GET_IMAGE can also read out of bounds.
Cap all 14 record-chain walk loops to BIOS_MAX_NUM_RECORD (256)
iterations. The atombios.h defines up to 22 distinct record types
and atomfirmware.h has 13. Assuming an average of less than 10
records per type (which is reasonable since most are connector-
based) 256 is a generous upper bound.
Fixes: 4562236b3b ("drm/amd/dc: Add dc display driver (v2)")
Assisted-by: Copilot:claude-opus-4.6 Mythos
Reviewed-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Ray Wu <ray.wu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 95700a3d66)
Cc: stable@vger.kernel.org
[Why & How]
During HDCP 2.x repeater authentication over HDMI, the driver reads the
sink's RxStatus register and extracts a 10-bit message size field (max
value 1023). This value is used as the read length for the ReceiverID
list without being clamped to the size of the destination buffer
rx_id_list[177]. A malicious HDMI repeater could advertise a message
size larger than the buffer, causing an out-of-bounds write during the
I2C read.
Clamp the read length in mod_hdcp_read_rx_id_list() to the size of the
rx_id_list buffer, matching the approach already used in the DP branch.
Fixes: eff682f83c ("drm/amd/display: Add DDC handles for HDCP2.2")
Assisted-by: Copilot:claude-opus-4.6
Reviewed-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Ray Wu <ray.wu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 229212219e)
Cc: stable@vger.kernel.org
[Why & How]
gpio_bitshift is a uint8_t read directly from the VBIOS GPIO pin table.
If the value is >= 32, the expression "1 << gpio_bitshift" triggers
undefined behaviour in C (shift count exceeds type width). On x86 the
shift is silently masked to 5 bits, producing an incorrect GPIO mask
that may cause wrong MMIO register bits to be toggled.
Validate gpio_bitshift before use and return BP_RESULT_BADBIOSTABLE for
out-of-range values.
Fixes: ae79c310b1 ("drm/amd/display: Add DCE12 bios parser support")
Assisted-by: Copilot:claude-opus-4.6
Reviewed-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Ray Wu <ray.wu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit eadf438ab8)
Cc: stable@vger.kernel.org
[Why & How]
dal_vector_reserve() computes the allocation size as
"capacity * vector->struct_size" using uint32_t arithmetic, which can
silently wrap to a small value on overflow. This would cause krealloc to
return a smaller buffer than expected, leading to heap overflows on
subsequent vector appends.
Replace krealloc() with krealloc_array() which performs an internal
overflow check and returns NULL on wrap, preventing the issue.
Fixes: 2004f45ef8 ("drm/amd/display: Use kernel alloc/free")
Assisted-by: Copilot:claude-opus-4.6
Reviewed-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Ray Wu <ray.wu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 3766856864)
Cc: stable@vger.kernel.org
[Why & How]
dp_sdp_message_debugfs_write() dereferences connector->base.state->crtc
without checking for NULL. A connector can be connected but not bound to
any CRTC (e.g. after hot-plug before the next atomic commit), causing a
kernel crash when writing to the sdp_message debugfs node.
The function also ignores the user-provided size argument and always
passes 36 bytes to copy_from_user(), reading past the user buffer when
size < 36.
Fix both issues by:
- Returning -ENODEV when connector->base.state or state->crtc is NULL
- Clamping write_size to min(size, sizeof(data))
Fixes: c7ba3653e9 ("drm/amd/display: Generic SDP message access in amdgpu")
Assisted-by: Copilot:claude-opus-4.6
Reviewed-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Ray Wu <ray.wu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 6ab4c36a52)
Cc: stable@vger.kernel.org
[Why & How]
The VBIOS integrated info tables (v1_11 and v2_1) contain HdmiRegNum and
Hdmi6GRegNum fields that are used as loop bounds when copying retimer I2C
register settings into fixed-size arrays (dp*_ext_hdmi_reg_settings[9]
and dp*_ext_hdmi_6g_reg_settings[3]). These u8 fields are not validated
before use, so a malformed VBIOS can specify values up to 255, causing an
out-of-bounds heap write during driver probe.
Clamp each register count to the destination array size using min_t()
before the copy loops, in both get_integrated_info_v11() and
get_integrated_info_v2_1().
Assisted-by: GitHub Copilot:claude-opus-4.6
Reviewed-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Ray Wu <ray.wu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 5a7f0ef901)
Cc: stable@vger.kernel.org
[Why & How]
The aux_rd_interval array in struct dc_lttpr_caps is declared with
MAX_REPEATER_CNT - 1 (7) elements, indexed 0..6. However, the offset
parameter passed to dp_get_eq_aux_rd_interval() can be as large as
MAX_REPEATER_CNT (8) when a sink reports 8 LTTPR repeaters via DPCD.
This leads to an out-of-bounds read of aux_rd_interval[7] when offset
is 8.
Fix this by growing aux_rd_interval to MAX_REPEATER_CNT elements to
accommodate the full range of valid repeater counts defined by the DP
spec.
Assisted-by: GitHub Copilot:Claude claude-4-opus
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Ray Wu <ray.wu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit a55a458a8d)
Cc: stable@vger.kernel.org
A compute shader dispatch encodes its workgroup counts in the CFG0..CFG2
registers. Kicking off a dispatch with a zero count in any of the three
dimensions is invalid. First, the hardware will process 0 as 65536,
while the user-space driver exposes a maximum of 65535. Over that, a
submission with a zeroed workgroup dimension should be a no-op.
These zeroed counts can reach the dispatch path through an indirect CSD
job, whose workgroup counts are only known once the indirect buffer is
read and may legitimately be zero, but such scenario should only result in
a no-op.
Overwrite the indirect CSD job workgroup counts with the indirect BO
ones, even if they are zeroed, and don't submit the job to the hardware
when any of the workgroup counts is zero, so the job completes immediately
instead of running the shader.
Cc: stable@vger.kernel.org
Fixes: d223f98f02 ("drm/v3d: Add support for compute shader dispatch.")
Suggested-by: Jose Maria Casanova Crespo <jmcasanova@igalia.com>
Reviewed-by: Iago Toral Quiroga <itoral@igalia.com>
Link: https://patch.msgid.link/20260602-v3d-fix-indirect-csd-v4-2-654309e32bc0@igalia.com
Signed-off-by: Maíra Canal <mcanal@igalia.com>
v3d_rewrite_csd_job_wg_counts_from_indirect() maps both the indirect
buffer and the workgroup buffer and is expected to release them before
returning. When any of the workgroup counts read from the buffer is zero,
the function bailed out early and skipped the cleanup, leaking the vaddr
mappings of both BOs.
Jump to the cleanup path instead of returning directly, so the mappings
are always dropped.
Cc: stable@vger.kernel.org
Fixes: 18b8413b25 ("drm/v3d: Create a CPU job extension for a indirect CSD job")
Suggested-by: Jose Maria Casanova Crespo <jmcasanova@igalia.com>
Reviewed-by: Iago Toral Quiroga <itoral@igalia.com>
Link: https://patch.msgid.link/20260602-v3d-fix-indirect-csd-v4-1-654309e32bc0@igalia.com
Signed-off-by: Maíra Canal <mcanal@igalia.com>
Fix the following W=1 kerneldoc warnings by adding the missing parameter
descriptions for @phase0_identity and @nn_interpolation in
dcss_scaler_filter_design() and @phase0_identity in
dcss_scaler_gaussian_filter()
Warning: drivers/gpu/drm/imx/dcss/dcss-scaler.c:173 function parameter 'phase0_identity' not described in 'dcss_scaler_gaussian_filter'
Warning: drivers/gpu/drm/imx/dcss/dcss-scaler.c:270 function parameter 'phase0_identity' not described in 'dcss_scaler_filter_design'
Warning: drivers/gpu/drm/imx/dcss/dcss-scaler.c:270 function parameter 'nn_interpolation' not described in 'dcss_scaler_filter_design'
Fixes: 9021c317b7 ("drm/imx: Add initial support for DCSS on iMX8MQ")
Signed-off-by: Yicong Hui <yiconghui@gmail.com>
Reviewed-by: Laurentiu Palcu <laurentiu.palcu@oss.nxp.com>
Link: https://patch.msgid.link/20260406180013.2442096-1-yiconghui@gmail.com
Signed-off-by: Liu Ying <victor.liu@nxp.com>
v3d_clean_caches() starts the cache-clean sequence by writing
V3D_L2TCACTL_TMUWCF to V3D_CTL_L2TCACTL and then polling for that bit to
clear. It does not, however, check for an L2T flush (L2TFLS) that may
still be in flight from a previous operation.
On pre-V3D 7.1 hardware, kicking off the TMU write-combiner flush while an
L2T flush is still pending can clobber bits in L2TCACTL and cause cache
inconsistencies.
Poll for L2TFLS to clear before writing L2TCACTL on V3D < 7.1, ensuring
any pending flush has completed before a new clean is issued.
Cc: stable@vger.kernel.org
Fixes: d223f98f02 ("drm/v3d: Add support for compute shader dispatch.")
Link: https://patch.msgid.link/20260530-v3d-fix-rpi4-freezes-v1-1-c2c8307da6ce@igalia.com
Signed-off-by: Maíra Canal <mcanal@igalia.com>
Reviewed-by: Iago Toral Quiroga <itoral@igalia.com>
drm_gem_change_handle_ioctl leaves the old handle live in the IDR
during the window between spin_unlock(table_lock) and the final
spin_lock(table_lock). A concurrent drm_gem_handle_delete on the old
handle succeeds in this window, decrements handle_count to 0, and frees
the GEM object while the new handle's IDR entry still references it.
NULL the old handle's IDR entry before dropping table_lock so that any
concurrent GEM_CLOSE on the old handle sees NULL and returns -EINVAL.
Restore the old entry on the prime-bookkeeping error path.
Fixes: 5e28b7b944 ("drm: Set old handle to NULL before prime swap in change_handle")
Signed-off-by: Zhenghang Xiao <kipreyyy@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Link: https://patch.msgid.link/20260526085313.26791-1-kipreyyy@gmail.com
Short summary of fixes pull:
amdxdna:
- require IOMMU on AIE2
dumb-buffer:
- prevent overflows in dumb-buffer creation
dma-buf:
- fix UAF in dma_buf_fd() tracepoint
hyperv:
- improve protocol validation
ivpu:
- test write offset in debugfs
rocket:
- fix UAF in bo creation
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patch.msgid.link/20260529070009.GA313534@linux.fritz.box
Fix integer overflow issues in the dumb buffer creation path:
1. drm_mode_create_dumb() does not bound width, height, or bpp
before passing them to driver callbacks. Downstream helpers
(e.g. drm_gem_dma_dumb_create_internal) perform pitch/size
alignment in u32 arithmetic that can overflow for extreme
values. Add hard limits: width and height < 8192, bpp <= 32.
No legitimate software rendering use case exceeds these.
2. drm_mode_align_dumb() uses roundup(pitch, hw_pitch_align)
without checking for overflow. If pitch is near U32_MAX,
roundup() wraps to a small value, making subsequent
check_mul_overflow() pass with a much smaller pitch than
intended. Add an overflow check after roundup.
3. drm_mode_align_dumb() uses ALIGN(size, hw_size_align) which
only works correctly for power-of-two alignment values.
Replace with roundup() which works for any alignment.
Suggested-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Rajat Gupta <rajat.gupta@oss.qualcomm.com>
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
