Simplify the driver's probe() function by using the devres
variant of stmmac_probe_config_dt().
The remove_new() callback now needs to be switched to
stmmac_pltfr_remove_no_dt().
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add sw fallback of tx checksum calculation for those tx queues that
don't support tx checksum offloading. DW xGMAC IP can be synthesized
such that it can support tx checksum offloading only for a few
initial tx queues. Also as Serge pointed out, for the DW QoS IP, tx
coe can be individually configured for each tx queue.
So when tx coe is enabled, for any tx queue that doesn't support
tx coe with 'coe-unsupported' flag set will have a sw fallback
happen in the driver for tx checksum calculation when any packets to
be transmitted on these tx queues.
Signed-off-by: Rohan G Thomas <rohan.g.thomas@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If, for any reason, the open-coded arithmetic causes a wraparound,
the protection that `struct_size()` adds against potential integer
overflows is defeated. Fix this by hardening call to `struct_size()`
with `size_add()`.
Fixes: 3f1071ec39 ("net: spider_net: Use struct_size() helper")
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Geoff Levand <geoff@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
If, for any reason, the open-coded arithmetic causes a wraparound, the
protection that `struct_size()` adds against potential integer overflows
is defeated. Fix this by hardening call to `struct_size()` with `size_mul()`.
Fixes: 2285ec872d ("mlxsw: spectrum_acl_bloom_filter: use struct_size() in kzalloc()")
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If we see a 0xff value from a PCI register read, we know that
the PCI connection is broken, possibly by a low level reset that
didn't go through the nice pci_error_handlers path.
Make use of the PCI cleanup code that we already have from the
reset handlers and add some detection and attempted recovery
from a broken PCI connection.
Signed-off-by: Shannon Nelson <shannon.nelson@amd.com>
Reviewed-by: Brett Creeley <brett.creeley@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement the callbacks for a nice PCI reset. These get called
when a user is nice enough to use the sysfs PCI reset entry, e.g.
echo 1 > /sys/bus/pci/devices/0000:2b:00.0/reset
Signed-off-by: Shannon Nelson <shannon.nelson@amd.com>
Reviewed-by: Brett Creeley <brett.creeley@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similar to what we do in the AdminQ, check for devcmd health
while waiting for an answer.
Signed-off-by: Shannon Nelson <shannon.nelson@amd.com>
Reviewed-by: Brett Creeley <brett.creeley@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support to fetch firmware info such as heartbeat miss count,
heartbeat interval. This shall be used for heartbeat monitor.
Signed-off-by: Shinas Rasheed <srasheed@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If, for any reason, `tx_stats_num + rx_stats_num` wraps around, the
protection that struct_size() adds against potential integer overflows
is defeated. Fix this by hardening call to struct_size() with size_add().
Fixes: 691f4077d5 ("gve: Replace zero-length array with flexible-array member")
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Split out the locked and unlocked sections of phy_state_machine() into
two separate functions which can be called inside the phydev lock and
outside the phydev lock as appropriate, thus allowing us to combine
the locked regions in the caller of phy_state_machine() with the
locked region inside phy_state_machine().
This avoids unnecessarily dropping the phydev lock which may allow
races to occur.
Tested-by: Jijie Shao <shaojijie@huawei.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the call to phy_suspend() to the end of phy_state_machine() after
we release the lock so that we can combine the locked areas.
phy_suspend() can not be called while holding phydev->lock as it has
caused deadlocks in the past.
Tested-by: Jijie Shao <shaojijie@huawei.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the call to start auto-negotiation inside the lock in the PHYLIB
state machine, calling the locked variant _phy_start_aneg(). This
avoids unnecessarily releasing and re-acquiring the lock.
Tested-by: Jijie Shao <shaojijie@huawei.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
phy_stop() calls phy_process_state_change() while holding the phydev
lock, so also arrange for phy_state_machine() to do the same, so that
this function is called with consistent locking.
Tested-by: Jijie Shao <shaojijie@huawei.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds partial Access Control List (ACL) support for the
ksz9477 family of switches. ACLs enable filtering of incoming layer 2
MAC, layer 3 IP, and layer 4 TCP/UDP packets on each port. They provide
additional capabilities for filtering routed network protocols and can
take precedence over other forwarding functions.
ACLs can filter ingress traffic based on header fields such as
source/destination MAC address, EtherType, IPv4 address, IPv4 protocol,
UDP/TCP ports, and TCP flags. The ACL is an ordered list of up to 16
access control rules programmed into the ACL Table. Each entry specifies
a set of matching conditions and action rules for controlling packet
forwarding and priority.
The ACL also implements a count function, generating an interrupt
instead of a forwarding action. It can be used as a watchdog timer or an
event counter. The ACL consists of three parts: matching rules, action
rules, and processing entries. Multiple match conditions can be either
AND'ed or OR'ed together.
This patch introduces support for a subset of the available ACL
functionality, specifically layer 2 matching and prioritization of
matched packets. For example:
tc qdisc add dev lan2 clsact
tc filter add dev lan2 ingress protocol 0x88f7 flower action skbedit prio 7
tc qdisc add dev lan1 clsact
tc filter add dev lan1 ingress protocol 0x88f7 flower action skbedit prio 7
The hardware offloading implementation was benchmarked against a
configuration without hardware offloading. This latter setup relied on a
software-based Linux bridge. No noticeable differences were observed
between the two configurations. Here is an example of software-based
test:
ip l s dev enu1u1 up
ip l s dev enu1u2 up
ip l s dev enu1u4 up
ethtool -A enu1u1 autoneg off rx off tx off
ethtool -A enu1u2 autoneg off rx off tx off
ethtool -A enu1u4 autoneg off rx off tx off
ip l a name br0 type bridge
ip l s dev br0 up
ip l s enu1u1 master br0
ip l s enu1u2 master br0
ip l s enu1u4 master br0
tc qdisc add dev enu1u1 root handle 1: ets strict 4 priomap 3 3 2 2 1 1 0 0
tc qdisc add dev enu1u4 root handle 1: ets strict 4 priomap 3 3 2 2 1 1 0 0
tc qdisc add dev enu1u2 root handle 1: ets strict 4 priomap 3 3 2 2 1 1 0 0
tc qdisc add dev enu1u1 clsact
tc filter add dev enu1u1 ingress protocol ipv4 flower action skbedit prio 7
tc qdisc add dev enu1u4 clsact
tc filter add dev enu1u4 ingress protocol ipv4 flower action skbedit prio 0
On a system attached to the port enu1u2 I run two iperf3 server
instances:
iperf3 -s -p 5210 &
iperf3 -s -p 5211 &
On systems attached to enu1u4 and enu1u1 I run:
iperf3 -u -c 172.17.0.1 -p 5210 -b100M -l1472 -t100
and
iperf3 -u -c 172.17.0.1 -p 5211 -b100M -l1472 -t100
As a result, IP traffic on port enu1u1 will be prioritized and take
precedence over IP traffic on port enu1u4
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Right now, the *_port_setup code is in dsa_switch_ops::port_enable(),
which is not the best place for it. This patch moves it to a more
suitable place, dsa_switch_ops::port_setup(), to match the function's
purpose and name.
This patch is a preparation for coming ACL support patch.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Benefit from the previous commit introducing exposure of devlink
instances relationship and set the nested instance for en auxiliary
device.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Benefit from the newly introduced rel infrastructure, treat the linecard
nested devlink instances in the same way as port function instances.
Convert the code to use the rel infrastructure.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Benefit from the existence of internal mlx5 notifier and extend it by
event MLX5_DRIVER_EVENT_SF_PEER_DEVLINK. Use this event from SF
auxiliary device probe/remove functions to pass the registered SF
devlink instance to the SF representor.
Process the new event in SF representor code and call
devl_port_fn_devlink_set() to do the assignments. Implement this in work
to avoid possible deadlock when probe/remove function of SF may be
called with devlink instance lock held during devlink reload.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Historically, the shared devlink_mutex prevented devlink instances from
being registered/unregistered during another devlink instance reload
operation. However, devlink_muxex is gone for some time now, this
limitation is no longer needed. Lift it.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The eswitch disable call does removal of all representors. Do that
before clearing the SF device table and maintain the same flow as during
SF devlink port removal, where the representor is removed before
the actual SF is removed.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When operating in fixed phy mode and if there is repeated open/close
phy test cases, everytime the fixed phy is registered as a new phy
which leads to overrun after 32 iterations. It is solved by adding
fixed_phy_unregister() in the phy_close path.
In phy_close path, netdev->phydev cannot be used directly in
fixed_phy_unregister() due to two reasons,
- netdev->phydev is set to NULL in phy_disconnect()
- fixed_phy_unregister() can be called only after phy_disconnect()
So saving the netdev->phydev in local variable 'phydev' and
passing it to phy_disconnect().
Signed-off-by: Pavithra Sathyanarayanan <Pavithra.Sathyanarayanan@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement SyncE support using newly introduced DPLL support.
Make sure that each PFs/VFs/SFs probed with appropriate capability
will spawn a dpll auxiliary device and register appropriate dpll device
and pin instances.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Signed-off-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add firmware admin command to access clock generation unit
configuration, it is required to enable Extended PTP and SyncE features
in the driver.
Add definitions of possible hardware variations of input and output pins
related to clock generation unit and functions to access the data.
Signed-off-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Signed-off-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-queue
Tony Nguyen says:
====================
Support rx-fcs on/off for VFs
Ahmed Zaki says:
Allow the user to turn on/off the CRC/FCS stripping through ethtool. We
first add the CRC offload capability in the virtchannel, then the feature
is enabled in ice and iavf drivers.
We make sure that the netdev features are fixed such that CRC stripping
cannot be disabled if VLAN rx offload (VLAN strip) is enabled. Also, VLAN
stripping cannot be enabled unless CRC stripping is ON.
Testing was done using tcpdump to make sure that the CRC is included in
the frame after:
# ethtool -K <interface> rx-fcs on
and is not included when it is back "off". Also, ethtool should return an
error for the above command if "rx-vlan-offload" is already on and at least
one VLAN interface/filter exists on the VF.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add device tree based drive strength configuration support. It is needed to
pass EMI validation on our hardware.
Configuration values are based on the vendor's reference driver.
Tested on KSZ9563R.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tony Nguyen says:
====================
Introduce Intel IDPF driver
Pavan Kumar Linga says:
This patch series introduces the Intel Infrastructure Data Path Function
(IDPF) driver. It is used for both physical and virtual functions. Except
for some of the device operations the rest of the functionality is the
same for both PF and VF. IDPF uses virtchnl version2 opcodes and
structures defined in the virtchnl2 header file which helps the driver
to learn the capabilities and register offsets from the device
Control Plane (CP) instead of assuming the default values.
The format of the series follows the driver init flow to interface open.
To start with, probe gets called and kicks off the driver initialization
by spawning the 'vc_event_task' work queue which in turn calls the
'hard reset' function. As part of that, the mailbox is initialized which
is used to send/receive the virtchnl messages to/from the CP. Once that is
done, 'core init' kicks in which requests all the required global resources
from the CP and spawns the 'init_task' work queue to create the vports.
Based on the capability information received, the driver creates the said
number of vports (one or many) where each vport is associated to a netdev.
Also, each vport has its own resources such as queues, vectors etc.
From there, rest of the netdev_ops and data path are added.
IDPF implements both single queue which is traditional queueing model
as well as split queue model. In split queue model, it uses separate queue
for both completion descriptors and buffers which helps to implement
out-of-order completions. It also helps to implement asymmetric queues,
for example multiple RX completion queues can be processed by a single
RX buffer queue and multiple TX buffer queues can be processed by a
single TX completion queue. In single queue model, same queue is used
for both descriptor completions as well as buffer completions. It also
supports features such as generic checksum offload, generic receive
offload (hardware GRO) etc.
---
v7:
Patch 2:
* removed pci_[disable|enable]_pcie_error_reporting as they are dropped
from the core
Patch 4, 9:
* used 'kasprintf' instead of 'snprintf' to avoid providing explicit
character string size which also fixes "-Wformat-truncation" warnings
Patch 14:
* used 'ethtool_sprintf' instead of 'snprintf' to avoid providing explicit
character string size which also fixes "-Wformat-truncation" warning
* add string format argument to the 'ethtool_sprintf' to avoid warning on
"-Wformat-security"
v6: https://lore.kernel.org/netdev/20230825235954.894050-1-pavan.kumar.linga@intel.com/
Note: 'Acked-by' was only added to patches 1, 2, 12 and not to the other
patches because of the changes in v6
Patch 3, 4, 5, 6, 7, 8, 9, 11, 13, 14, 15:
* renamed 'reset_lock' to 'vport_ctrl_lock' to reflect the lock usage
* to avoid defensive programming, used 'vport_ctrl_lock' for the user
callbacks that access the 'vport' to prevent the hardware reset thread
from releasing the 'vport', when the user callback is in progress
* added some variables to netdev private structure to avoid vport access
if possible from ethtool and ndo callbacks
* moved 'mac_filter_list_lock' and MAC related flags to vport_config
structure and refactored mac filter flow to handle asynchronous
ndo mac filter callbacks
* stop the queues before starting the reset flow to avoid TX hangs
* removed 'sw_mutex' and 'stop_mutex' as they are not needed anymore
* added missing clear bit in 'init_task' error path
* renamed labels appropriately
Patch 8:
* replaced page_pool_put_page with page_pool_put_full_page
* for the page pool max_len, used PAGE_SIZE
Patch 10, 11, 13:
* made use of the 'netif_txq_maybe_stop', '__netif_txq_completed_wake'
helper macros
Patch 13:
* removed IDPF_HR_RESET_IN_PROG flag check in idpf_tx_singleq_start
as it is defensive
Patch 14:
* removed max descriptor check as the core does that
* removed unnecessary error messages
* removed the stats that are common between the ones reported by ethtool
and ip link
* replaced snprintf with ethtool_sprintf
* added a comment to explain the reason for the max queue check
* as the netdev queues are set on alloc, there is no need to set
them again on reset unless there is a queue change, so move the
'idpf_set_real_num_queues' to 'idpf_initiate_soft_reset'
Patch 15:
* reworded the 'configure SRIOV' in the commit message
v5: https://lore.kernel.org/netdev/20230816004305.216136-1-anthony.l.nguyen@intel.com/
Most Patches:
* wrapped line limit to 80 chars to those which don't effect readability
Patch 12:
* in skb_add_rx_frag, offset 'headlen' w.r.t page_offset when adding a
frag to avoid adding the header again
Patch 14:
* added NULL check for 'rxq' when dereferencing it in page_pool_get_stats
v4: https://lore.kernel.org/netdev/20230808003416.3805142-1-anthony.l.nguyen@intel.com/
Patch 1:
* s/virtcnl/virtchnl
* removed the kernel doc for the error code definitions that don't exist
* reworded the summary part in the virtchnl2 header
Patch 3:
* don't set local variable to NULL on error
* renamed sq_send_command_out label with err_unlock
* don't use __GFP_ZERO in dma_alloc_coherent
Patch 4:
* introduced mailbox workqueue to process mailbox interrupts
Patch 3, 4, 5, 6, 7, 8, 9, 11, 15:
* removed unnecessary variable 0-init
Patch 3, 5, 7, 8, 9, 15:
* removed defensive programming checks wherever applicable
* removed IDPF_CAP_FIELD_LAST as it can be treated as defensive
programming
Patch 3, 4, 5, 6, 7:
* replaced IDPF_DFLT_MBX_BUF_SIZE with IDPF_CTLQ_MAX_BUF_LEN
Patch 2 to 15:
* add kernel-doc for idpf.h and idpf_txrx.h enums and structures
Patch 4, 5, 15:
* adjusted the destroy sequence of the workqueues as per the alloc
sequence
Patch 4, 5, 9, 15:
* scrub unnecessary flags in 'idpf_flags'
- IDPF_REMOVE_IN_PROG flag can take care of the cases where
IDPF_REL_RES_IN_PROG is used, removed the later one
- IDPF_REQ_[TX|RX]_SPLITQ are replaced with struct variables
- IDPF_CANCEL_[SERVICE|STATS]_TASK are redundant as the work queue
doesn't get rescheduled again after 'cancel_delayed_work_sync'
- IDPF_HR_CORE_RESET is removed as there is no set_bit for this flag
- IDPF_MB_INTR_TRIGGER is removed as it is not needed anymore with the
mailbox workqueue implementation
Patch 7 to 15:
* replaced the custom buffer recycling code with page pool API
* switched the header split buffer allocations from using a bunch of
pages to using one large chunk of DMA memory
* reordered some of the flows in vport_open to support page pool
Patch 8, 12:
* don't suppress the alloc errors by using __GFP_NOWARN
Patch 9:
* removed dyn_ctl_clrpba_m as it is not being used
Patch 14:
* introduced enum idpf_vport_reset_cause instead of using vport flags
* introduced page pool stats
v3: https://lore.kernel.org/netdev/20230616231341.2885622-1-anthony.l.nguyen@intel.com/
Patch 5:
* instead of void, used 'struct virtchnl2_create_vport' type for
vport_params_recvd and vport_params_reqd and removed the typecasting
* used u16/u32 as needed instead of int for variables which cannot be
negative and updated in all the places whereever applicable
Patch 6:
* changed the commit message to "add ptypes and MAC filter support"
* used the sender Signed-off-by as the last tag on all the patches
* removed unnecessary variables 0-init
* instead of fixing the code in this commit, fixed it in the commit
where the change was introduced first
* moved get_type_info struct on to the stack instead of memory alloc
* moved mutex_lock and ptype_info memory alloc outside while loop and
adjusted the return flow
* used 'break' instead of 'continue' in ptype id switch case
v2: https://lore.kernel.org/netdev/20230614171428.1504179-1-anthony.l.nguyen@intel.com/
Patch 2:
* added "Intel(R)" to the DRV_SUMMARY and Makefile.
Patch 4, 5, 6, 15:
* replaced IDPF_VC_MSG_PENDING flag with mutex 'vc_buf_lock' for the
adapter related virtchnl opcodes.
* get the mutex lock in the virtchnl send thread itself instead of
in receive thread.
Patch 5, 6, 7, 8, 9, 11, 14, 15:
* replaced IDPF_VPORT_VC_MSG_PENDING flag with mutex 'vc_buf_lock' for
the vport related virtchnl opcodes.
* get the mutex lock in the virtchnl send thread itself instead of
in receive thread.
Patch 6:
* converted get_ptype_info logic from 1:N to 1:1 message exchange for
better handling of mutex lock.
Patch 15:
* introduced 'stats_lock' spinlock to avoid concurrent stats update.
v1: https://lore.kernel.org/netdev/20230530234501.2680230-1-anthony.l.nguyen@intel.com/
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This glue driver is created based on the arch-code
implemented earlier with the platform-specific settings.
Use syscon for SYSCON register access.
And modify MAINTAINERS to add a new F: entry for this driver.
Partially based on the previous work by Serge Semin.
Signed-off-by: Keguang Zhang <keguang.zhang@gmail.com>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Follow the style used in the core kernel (e.g.
include/linux/etherdevice.h and include/linux/in6.h) for the PTP IPv6
and Ethernet addresses. No functional changes.
Signed-off-by: Alex Austin <alex.austin@amd.com>
Reviewed-by: Edward Cree <ecree.xilinx@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check if wlan.offload_enable and wlan.offload_disable callbacks are set
in mtk_wed_flow_add/mtk_wed_flow_remove since mt7996 will not rely
on them.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for half duplex operation at 10M and 100M link
speeds for AM654x/AM64x devices.
- Driver configures rand_seed, a random number, in DMEM HD_RAND_SEED_OFFSET
field, which will be used by firmware for Back off time calculation.
- Driver informs FW about half duplex link operation in DMEM
PORT_LINK_SPEED_OFFSET field by setting bit 7 for 10/100M HD.
Hence, the half duplex operation depends on board design the
"ti,half-duplex-capable" property has to be enabled for ICSS-G ports if HW
is capable to perform half duplex.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We auto-negotiate most ports in the RTL8366RB driver, but
the CPU port is hard-coded to 1Gbit, full duplex, tx and
rx pause.
This isn't very nice. People may configure speed and
duplex differently in the device tree.
Actually respect the arguments passed to the function for
the CPU port, which get passed properly after Russell's
patch "net: dsa: realtek: add phylink_get_caps implementation"
After this the link is still set up properly.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PTP block supports generating PPS output signal on GPIO pin. This patch
adds the support in the PTP PHC driver using standard periodic output
interface.
User can enable/disable/configure PPS by writing to the below sysfs entry
echo perout.index start.sec start.nsec period.sec period.nsec >
/sys/class/ptp/ptp0/period
Example to generate 50% duty cycle PPS signal:
echo 0 0 0 0 500000000 > /sys/class/ptp/ptp0/period
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com>
Signed-off-by: Sai Krishna <saikrishnag@marvell.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add spin lock protection for irq {un}mask registers' control.
After napi_complete_done() and this protection were applied,
a lot of redundant interrupts no longer occur.
For example: when "iperf3 -c <ipaddr> -R" on R-Car S4-8 Spider
Before the patches are applied: about 800,000 times happened
After the patches were applied: about 100,000 times happened
Fixes: 3590918b5d ("net: ethernet: renesas: Add support for "Ethernet Switch"")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
This is based on alx driver commit 881d0327db ("net: alx: Work around
the DMA RX overflow issue").
The alx and atl1c drivers had RX overflow error which was why a custom
allocator was created to avoid certain addresses. The simpler workaround
then created for alx driver, but not for atl1c due to lack of tester.
Instead of using a custom allocator, check the allocated skb address and
use skb_reserve() to move away from problematic 0x...fc0 address.
Tested on AR8131 on Acer 4540.
Signed-off-by: Sieng-Piaw Liew <liew.s.piaw@gmail.com>
Link: https://lore.kernel.org/r/20230912010711.12036-1-liew.s.piaw@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Add support for SRIOV: send the requested number of VFs
to the device Control Plane, via the virtchnl message
and then enable the VFs using 'pci_enable_sriov'.
Add other ndo ops supported by the driver such as features_check,
set_rx_mode, validate_addr, set_mac_address, change_mtu, get_stats64,
set_features, and tx_timeout. Initialize the statistics task which
requests the queue related statistics to the CP. Add loopback
and promiscuous mode support and the respective virtchnl messages.
Finally, add documentation and build support for the driver.
Signed-off-by: Joshua Hay <joshua.a.hay@intel.com>
Co-developed-by: Alan Brady <alan.brady@intel.com>
Signed-off-by: Alan Brady <alan.brady@intel.com>
Co-developed-by: Madhu Chittim <madhu.chittim@intel.com>
Signed-off-by: Madhu Chittim <madhu.chittim@intel.com>
Co-developed-by: Phani Burra <phani.r.burra@intel.com>
Signed-off-by: Phani Burra <phani.r.burra@intel.com>
Reviewed-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Co-developed-by: Pavan Kumar Linga <pavan.kumar.linga@intel.com>
Signed-off-by: Pavan Kumar Linga <pavan.kumar.linga@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Initialize all the ethtool ops that are supported by the driver and
add the necessary support for the ethtool callbacks. Also add
asynchronous link notification virtchnl support where the device
Control Plane sends the link status and link speed as an
asynchronous event message. Driver report the link speed on
ethtool .idpf_get_link_ksettings query.
Introduce soft reset function which is used by some of the ethtool
callbacks such as .set_channels, .set_ringparam etc. to change the
existing queue configuration. It deletes the existing queues by sending
delete queues virtchnl message to the CP and calls the 'vport_stop' flow
which disables the queues, vport etc. New set of queues are requested to
the CP and reconfigure the queue context by calling the 'vport_open'
flow. Soft reset flow also adjusts the number of vectors associated to a
vport if .set_channels is called.
Signed-off-by: Alan Brady <alan.brady@intel.com>
Co-developed-by: Alice Michael <alice.michael@intel.com>
Signed-off-by: Alice Michael <alice.michael@intel.com>
Co-developed-by: Joshua Hay <joshua.a.hay@intel.com>
Signed-off-by: Joshua Hay <joshua.a.hay@intel.com>
Co-developed-by: Phani Burra <phani.r.burra@intel.com>
Signed-off-by: Phani Burra <phani.r.burra@intel.com>
Reviewed-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Co-developed-by: Pavan Kumar Linga <pavan.kumar.linga@intel.com>
Signed-off-by: Pavan Kumar Linga <pavan.kumar.linga@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add support to handle interrupts for the RX completion queue and
RX buffer queue. When the interrupt fires on RX completion queue,
process the RX descriptors that are received. Allocate and prepare
the SKB with the RX packet info, for both data and header buffer.
IDPF uses software maintained refill queues to manage buffers between
RX queue producer and the buffer queue consumer. They are required in
order to maintain a lockless buffer management system and are strictly
software only constructs. Instead of updating the RX buffer queue tail
with available buffers right after the clean routine, it posts the
buffer ids to the refill queues, only to post them to the HW later.
If the generic receive offload (GRO) is enabled in the capabilities
and turned on by default or via ethtool, then HW performs the
packet coalescing if certain criteria are met by the incoming
packets and updates the RX descriptor. Similar to GRO, if generic
checksum is enabled, HW computes the checksum and updates the
respective fields in the descriptor. Add support to update the
SKB fields with the GRO and the generic checksum received.
Signed-off-by: Alan Brady <alan.brady@intel.com>
Co-developed-by: Joshua Hay <joshua.a.hay@intel.com>
Signed-off-by: Joshua Hay <joshua.a.hay@intel.com>
Co-developed-by: Madhu Chittim <madhu.chittim@intel.com>
Signed-off-by: Madhu Chittim <madhu.chittim@intel.com>
Co-developed-by: Phani Burra <phani.r.burra@intel.com>
Signed-off-by: Phani Burra <phani.r.burra@intel.com>
Reviewed-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Co-developed-by: Pavan Kumar Linga <pavan.kumar.linga@intel.com>
Signed-off-by: Pavan Kumar Linga <pavan.kumar.linga@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add support to handle the interrupts for the TX completion queue and
process the various completion types.
In the flow scheduling mode, the driver processes primarily buffer
completions as well as descriptor completions occasionally. This mode
supports out of order TX completions. To do so, HW generates one buffer
completion per packet. Each of those completions contains the unique tag
provided during the TX encoding which is used to locate the packet either
on the TX buffer ring or in a hash table. The hash table is used to track
TX buffer information so the descriptor(s) for a given packet can be
reused while the driver is still waiting on the buffer completion(s).
Packets end up in the hash table in one of 2 ways: 1) a packet was
stashed during descriptor completion cleaning, or 2) because an out of
order buffer completion was processed. A descriptor completion arrives
only every so often and is primarily used to guarantee the TX descriptor
ring can be reused without having to wait on the individual buffer
completions. E.g. a descriptor completion for N+16 guarantees HW read all
of the descriptors for packets N through N+15, therefore all of the
buffers for packets N through N+15 are stashed into the hash table and the
descriptors can be reused for more TX packets. Similarly, a packet can be
stashed in the hash table because an out an order buffer completion was
processed. E.g. processing a buffer completion for packet N+3 implies that
HW read all of the descriptors for packets N through N+3 and they can be
reused. However, the HW did not do the DMA yet. The buffers for packets N
through N+2 cannot be freed, so they are stashed in the hash table.
In either case, the buffer completions will eventually be processed for
all of the stashed packets, and all of the buffers will be cleaned from
the hash table.
In queue based scheduling mode, the driver processes primarily descriptor
completions and cleans the TX ring the conventional way.
Finally, the driver triggers a TX queue drain after sending the disable
queues virtchnl message. When the HW completes the queue draining, it
sends the driver a queue marker packet completion. The driver determines
when all TX queues have been drained and proceeds with the disable flow.
With this, the driver can send TX packets and clean up the resources
properly.
Signed-off-by: Joshua Hay <joshua.a.hay@intel.com>
Co-developed-by: Alan Brady <alan.brady@intel.com>
Signed-off-by: Alan Brady <alan.brady@intel.com>
Co-developed-by: Madhu Chittim <madhu.chittim@intel.com>
Signed-off-by: Madhu Chittim <madhu.chittim@intel.com>
Co-developed-by: Phani Burra <phani.r.burra@intel.com>
Signed-off-by: Phani Burra <phani.r.burra@intel.com>
Reviewed-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Co-developed-by: Pavan Kumar Linga <pavan.kumar.linga@intel.com>
Signed-off-by: Pavan Kumar Linga <pavan.kumar.linga@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
