Always enable HS video mode setting the TXMD bit, without this change no
video output is present with DSI sinks that are setting
MIPI_DSI_MODE_LPM flag (tested with LT8912B DSI-HDMI bridge).
Previously the driver was enabling HS mode only when the DSI sink was
not explicitly setting the MIPI_DSI_MODE_LPM, however this is not
correct.
The MIPI_DSI_MODE_LPM is supposed to indicate that the sink is willing
to receive data in low power mode, however clearing the
TC358768_DSI_CONTROL_TXMD bit will make the TC358768 send video in
LP mode that is not the intended behavior.
Fixes: ff1ca6397b ("drm/bridge: Add tc358768 driver")
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230427142934.55435-2-francesco@dolcini.it
When reduced version firmware files were added (matching major
component being the only strict requirement), the minor version was
still tracked and a notification reported if it was older. However,
the patch version should really be tracked as well for the same
reasons. The KMD can work without the change but if the effort has
been taken to release a new firmware with the change then there must
be a valid reason for doing so - important bug fix, security fix, etc.
And in that case it would be good to alert the user if they are
missing out on that new fix.
v2: Use correct patch version number and drop redunant debug print
(review by Daniele / CI results).
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Reviewed-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230504202252.1104212-2-John.C.Harrison@Intel.com
Commit 9a826ddba6 ("[ALSA] pcm core: fix silence_start calculations")
came with exactly the right commit message, but the patch just made
things broken in a different way: We'd fill at a too low address if the
area was already partially zeroed, so we'd under-fill. This affected
both thresholded mode (where it was somewhat less likely) and top-up
mode (where it would be the case consistently).
Co-developed-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Link: https://lore.kernel.org/r/20230505155244.2312199-3-oswald.buddenhagen@gmx.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The snd_pcm_playback_hw_avail() function uses runtime->status->hw_ptr.
Unfortunately, in case when we call this function from snd_pcm_update_hw_ptr0(),
this variable contains the previous hardware pointer. Use the new_hw_ptr
argument to calculate hw_avail (filled samples by the user space) to
correct the threshold comparison.
The new_hw_ptr argument may also be set to ULONG_MAX which means the
initialization phase. In this case, use runtime->status->hw_ptr.
Suggested-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Reviewed-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
Link: https://lore.kernel.org/r/20230505155244.2312199-2-oswald.buddenhagen@gmx.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
ASoC: Fixes for v6.4
A small set of fixes and device quirks that have come in during the
merge window, the Qualcomm fix seems quite large but it's mainly code
motion so looks larger than it is.
If a function had ever had IPMODIFY or DIRECT attached to it, where this
is how live kernel patching and BPF overrides work, mark them and display
an "M" in the enabled_functions and touched_functions files. This can be
used for debugging. If a function had been modified and later there's a bug
in the code related to that function, this can be used to know if the cause
is possibly from a live kernel patch or a BPF program that changed the
behavior of the code.
Also update the documentation on the enabled_functions and
touched_functions output, as it was missing direct callers and CALL_OPS.
And include this new modify attribute.
Link: https://lore.kernel.org/linux-trace-kernel/20230502213233.004e3ae4@gandalf.local.home
Cc: Mark Rutland <mark.rutland@arm.com>
Acked-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
If we disable vblank when entering self-refresh, vblank APIs (like
DRM_IOCTL_WAIT_VBLANK) no longer work. But user space is not aware when
we enter self-refresh, so this appears to be an API violation -- that
DRM_IOCTL_WAIT_VBLANK fails with EINVAL whenever the display is idle and
enters self-refresh.
The downstream driver used by many of these systems never used to
disable vblank for PSR, and in fact, even upstream, we didn't do that
until radically redesigning the state machine in commit 6c836d965b
("drm/rockchip: Use the helpers for PSR").
Thus, it seems like a reasonable API fix to simply restore that
behavior, and leave vblank enabled.
Note that this appears to potentially unbalance the
drm_crtc_vblank_{off,on}() calls in some cases, but:
(a) drm_crtc_vblank_on() documents this as OK and
(b) if I do the naive balancing, I find state machine issues such that
we're not in sync properly; so it's easier to take advantage of (a).
This issue was exposed by IGT's kms_vblank tests, and reported by
KernelCI. The bug has been around a while (longer than KernelCI
noticed), but was only exposed once self-refresh was bugfixed more
recently, and so KernelCI could properly test it. Some other notes in:
https://lore.kernel.org/dri-devel/Y6OCg9BPnJvimQLT@google.com/
Re: renesas/master bisection: igt-kms-rockchip.kms_vblank.pipe-A-wait-forked on rk3399-gru-kevin
== Backporting notes: ==
Marking as 'Fixes' commit 6c836d965b ("drm/rockchip: Use the helpers
for PSR"), but it probably depends on commit bed030a49f
("drm/rockchip: Don't fully disable vop on self refresh") as well.
We also need the previous patch ("drm/atomic: Allow vblank-enabled +
self-refresh "disable""), of course.
v3:
* no update
v2:
* skip unnecessary lock/unlock
Fixes: 6c836d965b ("drm/rockchip: Use the helpers for PSR")
Cc: <stable@vger.kernel.org>
Reported-by: "kernelci.org bot" <bot@kernelci.org>
Link: https://lore.kernel.org/dri-devel/Y5itf0+yNIQa6fU4@sirena.org.uk/
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230109171809.v3.2.Ic07cba4ab9a7bd3618a9e4258b8f92ea7d10ae5a@changeid
The self-refresh helper framework overloads "disable" to sometimes mean
"go into self-refresh mode," and this mode activates automatically
(e.g., after some period of unchanging display output). In such cases,
the display pipe is still considered "on", and user-space is not aware
that we went into self-refresh mode. Thus, users may expect that
vblank-related features (such as DRM_IOCTL_WAIT_VBLANK) still work
properly.
However, we trigger the WARN_ONCE() here if a CRTC driver tries to leave
vblank enabled.
Add a different expectation: that CRTCs *should* leave vblank enabled
when going into self-refresh.
This patch is preparation for another patch -- "drm/rockchip: vop: Leave
vblank enabled in self-refresh" -- which resolves conflicts between the
above self-refresh behavior and the API tests in IGT's kms_vblank test
module.
== Some alternatives discussed: ==
It's likely that on many display controllers, vblank interrupts will
turn off when the CRTC is disabled, and so in some cases, self-refresh
may not support vblank. To support such cases, we might consider
additions to the generic helpers such that we fire vblank events based
on a timer.
However, there is currently only one driver using the common
self-refresh helpers (i.e., rockchip), and at least as of commit
bed030a49f ("drm/rockchip: Don't fully disable vop on self refresh"),
the CRTC hardware is powered enough to continue to generate vblank
interrupts.
So we chose the simpler option of leaving vblank interrupts enabled. We
can reevaluate this decision and perhaps augment the helpers if/when we
gain a second driver that has different requirements.
v3:
* include discussion summary
v2:
* add 'ret != 0' warning case for self-refresh
* describe failing test case and relation to drm/rockchip patch better
Cc: <stable@vger.kernel.org> # dependency for "drm/rockchip: vop: Leave
# vblank enabled in self-refresh"
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230109171809.v3.1.I3904f697863649eb1be540ecca147a66e42bfad7@changeid
Commit 2b6a7409ac ("thermal: intel: menlow: Get rid of this driver")
removes the driver drivers/thermal/intel/intel_menlow.c, but misses to
remove its reference in MAINTAINERS.
Hence, ./scripts/get_maintainer.pl --self-test=patterns complains about a
broken reference.
Remove the INTEL MENLOW THERMAL DRIVER section in MAINTAINERS.
Fixes: 2b6a7409ac ("thermal: intel: menlow: Get rid of this driver")
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Fix a long-standing flaw in x86's TDP MMU where unloading roots on a vCPU can
result in the root being freed even though the root is completely valid and
can be reused as-is (with a TLB flush).
Fix kernel-doc warnings from the kernel test robot:
jornada720_ssp.c:24: warning: Function parameter or member 'jornada_ssp_lock' not described in 'DEFINE_SPINLOCK'
jornada720_ssp.c:24: warning: expecting prototype for arch/arm/mac(). Prototype was for DEFINE_SPINLOCK() instead
jornada720_ssp.c:34: warning: Function parameter or member 'byte' not described in 'jornada_ssp_reverse'
jornada720_ssp.c:57: warning: Function parameter or member 'byte' not described in 'jornada_ssp_byte'
jornada720_ssp.c:85: warning: Function parameter or member 'byte' not described in 'jornada_ssp_inout'
Link: lore.kernel.org/r/202304210535.tWby3jWF-lkp@intel.com
Fixes: 69ebb22277 ("[ARM] 4506/1: HP Jornada 7XX: Addition of SSP Platform Driver")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kernel test robot <lkp@intel.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Kristoffer Ericson <Kristoffer.ericson@gmail.com>
Cc: patches@armlinux.org.uk
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
When unwind instruction is 0xb2,the subsequent instructions
are uleb128 bytes.
For now,it uses only the first uleb128 byte in code.
For vsp increments of 0x204~0x400,use one uleb128 byte like below:
0xc06a00e4 <unwind_test_work>: 0x80b27fac
Compact model index: 0
0xb2 0x7f vsp = vsp + 1024
0xac pop {r4, r5, r6, r7, r8, r14}
For vsp increments larger than 0x400,use two uleb128 bytes like below:
0xc06a00e4 <unwind_test_work>: @0xc0cc9e0c
Compact model index: 1
0xb2 0x81 0x01 vsp = vsp + 1032
0xac pop {r4, r5, r6, r7, r8, r14}
The unwind works well since the decoded uleb128 byte is also 0x81.
For vsp increments larger than 0x600,use two uleb128 bytes like below:
0xc06a00e4 <unwind_test_work>: @0xc0cc9e0c
Compact model index: 1
0xb2 0x81 0x02 vsp = vsp + 1544
0xac pop {r4, r5, r6, r7, r8, r14}
In this case,the decoded uleb128 result is 0x101(vsp=0x204+(0x101<<2)).
While the uleb128 used in code is 0x81(vsp=0x204+(0x81<<2)).
The unwind aborts at this frame since it gets incorrect vsp.
To fix this,add uleb128 decode to cover all the above case.
Signed-off-by: Haibo Li <haibo.li@mediatek.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Alexandre Mergnat <amergnat@baylibre.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
The call to phy_stop() races with the later call to phy_disconnect(),
resulting in concurrent phy_suspend() calls being run from different
CPUs. The final call to phy_disconnect() ensures that the PHY is
stopped and suspended, too.
Fixes: c96e731c93 ("net: bcmgenet: connect and disconnect from the PHY state machine")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vlad Buslov says:
====================
Fixes for miss to tc action series
Changes V1 -> V2:
- Added new patch reverting Ivan's fix for the same issue.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When replacing a filter (i.e. 'fold' pointer is not NULL) the insertion of
new filter to idr is postponed until later in code since handle is already
provided by the user. However, the error handling code in fl_change()
always assumes that the new filter had been inserted into idr. If error
handler is reached when replacing existing filter it may remove it from idr
therefore making it unreachable for delete or dump afterwards. Fix the
issue by verifying that 'fold' argument wasn't provided by caller before
calling idr_remove().
Fixes: 08a0063df3 ("net/sched: flower: Move filter handle initialization earlier")
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Reviewed-by: Pedro Tammela <pctammela@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the current xdp_xmit implementation, if any single frame fails to
transmit due to insufficient buffer descriptors, the function nevertheless
reports success in sending all frames. This results in erroneously
indicating that frames were transmitted when in fact they were dropped.
This patch fixes the issue by ensureing the return value properly
indicates the actual number of frames successfully transmitted, rather than
potentially reporting success for all frames when some could not transmit.
Fixes: 6d6b39f180 ("net: fec: add initial XDP support")
Signed-off-by: Gagandeep Singh <g.singh@nxp.com>
Signed-off-by: Shenwei Wang <shenwei.wang@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce xdp_features support for bonding driver according to the slave
devices attached to the master one. xdp_features is required whenever we
want to xdp_redirect traffic into a bond device and then into selected
slaves attached to it.
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Acked-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Fixes: 66c0e13ad2 ("drivers: net: turn on XDP features")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Reviewed-by: Jussi Maki <joamaki@gmail.com>
Tested-by: Jussi Maki <joamaki@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should check whether the current SFI (Stream Filter Instance) table
is full before creating a new SFI entry. However, the previous logic
checks the handle by mistake and might lead to unpredictable behavior.
Fixes: 888ae5a395 ("net: enetc: add tc flower psfp offload driver")
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We used to have a mailing list in the MAINTAINERS file, but removed this
when we became part of Xilinx as it stopped working.
Now inside AMD we have the list again. Add it back so patches will be seen
by all sfc developers.
Signed-off-by: Martin Habets <habetsm.xilinx@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For multi-queue and large ring-size use case, the following error
occurred when free_unused_bufs:
rcu: INFO: rcu_sched self-detected stall on CPU.
Fixes: 986a4f4d45 ("virtio_net: multiqueue support")
Signed-off-by: Wenliang Wang <wangwenliang.1995@bytedance.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On mt753x_cpu_port_enable() there's code that enables flooding for the CPU
port only. Since mt753x_cpu_port_enable() runs twice when both CPU ports
are enabled, port 6 becomes the only port to forward the frames to. But
port 5 is the active port, so no frames received from the user ports will
be forwarded to port 5 which breaks network connectivity.
Every bit of the BC_FFP, UNM_FFP, and UNU_FFP bits represents a port. Fix
this issue by setting the bit that corresponds to the CPU port without
overwriting the other bits.
Clear the bits beforehand only for the MT7531 switch. According to the
documents MT7621 Giga Switch Programming Guide v0.3 and MT7531 Reference
Manual for Development Board v1.0, after reset, the BC_FFP, UNM_FFP, and
UNU_FFP bits are set to 1 for MT7531, 0 for MT7530.
The commit 5e5502e012 ("net: dsa: mt7530: fix roaming from DSA user
ports") silently changed the method to set the bits on the MT7530_MFC.
Instead of clearing the relevant bits before mt7530_cpu_port_enable()
which runs under a for loop, the commit started doing it on
mt7530_cpu_port_enable().
Back then, this didn't really matter as only a single CPU port could be
used since the CPU port number was hardcoded. The driver was later changed
with commit 1f9a6abecf ("net: dsa: mt7530: get cpu-port via dp->cpu_dp
instead of constant") to retrieve the CPU port via dp->cpu_dp. With that,
this silent change became an issue for when using multiple CPU ports.
Fixes: 5e5502e012 ("net: dsa: mt7530: fix roaming from DSA user ports")
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The multi-chip module MT7530 switch with a 40 MHz oscillator on the
MT7621AT, MT7621DAT, and MT7621ST SoCs forwards corrupt frames using
trgmii.
This is caused by the assumption that MT7621 SoCs have got 150 MHz PLL,
hence using the ncpo1 value, 0x0780.
My testing shows this value works on Unielec U7621-06, Bartel's testing
shows it won't work on Hi-Link HLK-MT7621A and Netgear WAC104. All devices
tested have got 40 MHz oscillators.
Using the value for 125 MHz PLL, 0x0640, works on all boards at hand. The
definitions for 125 MHz PLL exist on the Banana Pi BPI-R2 BSP source code
whilst 150 MHz PLL don't.
Forwarding frames using trgmii on the MCM MT7530 switch with a 25 MHz
oscillator on the said MT7621 SoCs works fine because the ncpo1 value
defined for it is for 125 MHz PLL.
Change the 150 MHz PLL comment to 125 MHz PLL, and use the 125 MHz PLL
ncpo1 values for both oscillator frequencies.
Link: 81d24bbce7/u-boot-mt/drivers/net/rt2880_eth.c (L2195)
Fixes: 7ef6f6f8d2 ("net: dsa: mt7530: Add MT7621 TRGMII mode support")
Tested-by: Bartel Eerdekens <bartel.eerdekens@constell8.be>
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Seemingly I mis-implemented the dependencies here. The OpenSBI docs only
point out that the "riscv,event-to-mhpmcounters property is mandatory if
riscv,event-to-mhpmevent is present". It never claims that
riscv,event-to-mhpmcounters requires riscv,event-to-mhpmevent.
Drop the dependency of riscv,event-to-mhpmcounters on
riscv,event-to-mhpmevent.
Fixes: 7e38085d9c ("dt-bindings: riscv: add SBI PMU event mappings")
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Atish Patra <atishp@rivosinc.com>
Link: https://lore.kernel.org/r/20230404-tractor-confusing-8852e552539a@spud
Signed-off-by: Rob Herring <robh@kernel.org>
When matching DFS connections, we can't rely on the values set in
cifs_sb_info::prepath and cifs_tcon::tree_name as they might change
during DFS failover. The DFS referrals related to a specific DFS tcon
are already matched earlier in match_server(), therefore we can safely
skip those checks altogether as the connection is guaranteed to be
unique for the DFS tcon.
Besides, when creating or finding an SMB session, make sure to also
refcount any DFS root session related to it (cifs_ses::dfs_root_ses),
so if a new DFS mount ends up reusing the connection from the old
mount while there was an umount(2) still in progress (e.g. umount(2)
-> cifs_umount() -> reconnect -> cifs_put_tcon()), the connection
could potentially be put right after the umount(2) finished.
Patch has minor update to include fix for unused variable issue
noted by the kernel test robot
Reported-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/oe-kbuild-all/202305041040.j7W2xQSy-lkp@intel.com/
Cc: stable@vger.kernel.org # v6.2+
Signed-off-by: Paulo Alcantara (SUSE) <pc@manguebit.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Pull ceph updates from Ilya Dryomov:
"A few filesystem improvements, with a rather nasty use-after-free fix
from Xiubo intended for stable"
* tag 'ceph-for-6.4-rc1' of https://github.com/ceph/ceph-client:
ceph: reorder fields in 'struct ceph_snapid_map'
ceph: pass ino# instead of old_dentry if it's disconnected
ceph: fix potential use-after-free bug when trimming caps
ceph: implement writeback livelock avoidance using page tagging
ceph: do not print the whole xattr value if it's too long
