In order to let bridge chains implement HDMI connector infrastructure,
add necessary glue code to the drm_bridge_connector. In case there is a
bridge that sets DRM_BRIDGE_OP_HDMI, drm_bridge_connector will register
itself as a HDMI connector and provide proxy drm_connector_hdmi_funcs
implementation.
Note, to simplify implementation, there can be only one bridge in a
chain that sets DRM_BRIDGE_OP_HDMI. Setting more than one is considered
an error. This limitation can be lifted later, if the need arises.
Acked-by: Maxime Ripard <mripard@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240607-bridge-hdmi-connector-v5-3-ab384e6021af@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
DRM_FORMAT_RGB888 is 24 bits per pixel and it would be natural to send it
on the SPI bus using a 24 bits per word transfer. The problem with this
is that not all SPI controllers support 24 bpw.
Since DRM_FORMAT_RGB888 is stored in memory as little endian and the SPI
bus is big endian we use 8 bpw to always get the same pixel format on the
bus: b8g8r8.
The MIPI DCS specification lists the standard commands that can be sent
over the MIPI DBI interface. The set_address_mode (36h) command has one
bit in the parameter that controls RGB/BGR order. This means that the
controller can be configured to receive the pixel as BGR.
RGB888 is rarely supported on these controllers but RGB666 is very common.
All datasheets I have seen do at least support the pixel format option
where each color is sent as one byte and the 6 MSB's are used.
All this put together means that we can send each pixel as b8g8r8 and an
RGB666 capable controller sees this as b6x2g6x2r6x2.
v4:
- s/emulation_format/pixel_format/ (Dmitry)
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240604-panel-mipi-dbi-rgb666-v4-4-d7c2bcb9b78d@tronnes.org
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
MIPI DCS write/set commands have 8 bit parameters except for the
write_memory commands where it depends on the pixel format.
drm_mipi_dbi does currently only support RGB565 which is 16-bit and it
has to make sure that the pixels enters the SPI bus in big endian format
since the MIPI DBI spec doesn't have support for little endian.
drm_mipi_dbi is optimized for DBI interface option 3 which means that the
16-bit bytes are swapped by the upper layer if the SPI bus does not
support 16 bits per word, signified by the swap_bytes member.
In order to support both 16-bit and 24-bit pixel transfers we need a way
to tell the DBI command layer the format of the buffer. Add a
write_memory_bpw member that the upper layer can use to tell how many
bits per word to use for the SPI transfer.
v4:
- Expand the commit message (Dmitry)
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240604-panel-mipi-dbi-rgb666-v4-3-d7c2bcb9b78d@tronnes.org
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
The register address of the XLCDC IP used in SAM9X7 SoC family
are different from the previous HLCDC. Defining those address
space with valid macros.
Signed-off-by: Durai Manickam KR <durai.manickamkr@microchip.com>
[manikandan.m@microchip.com: Remove unused macro definitions]
Signed-off-by: Manikandan Muralidharan <manikandan.m@microchip.com>
Acked-by: Lee Jones <lee@kernel.org>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240424053351.589830-3-manikandan.m@microchip.com
Most of the HDMI controllers have an upper TMDS character rate limit
they can't exceed. On "embedded"-grade display controllers, it will
typically be lower than what high-grade monitors can provide these days,
so drivers will filter the TMDS character rate based on the controller
capabilities.
To make that easier to handle for drivers, let's provide an optional
hook to be implemented by drivers so they can tell the HDMI controller
helpers if a given TMDS character rate is reachable for them or not.
This will then be useful to figure out the best format and bpc count for
a given mode.
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240527-kms-hdmi-connector-state-v15-13-c5af16c3aae2@kernel.org
Signed-off-by: Maxime Ripard <mripard@kernel.org>
A lot of the various HDMI drivers duplicate some logic that depends on
the HDMI spec itself and not really a particular hardware
implementation.
Output BPC or format selection, infoframe generation are good examples
of such areas.
This creates a lot of boilerplate, with a lot of variations, which makes
it hard for userspace to rely on, and makes it difficult to get it right
for drivers.
In the next patches, we'll add a lot of infrastructure around the
drm_connector and drm_connector_state structures, which will allow to
abstract away the duplicated logic. This infrastructure comes with a few
requirements though, and thus we need a new initialization function.
Hopefully, this will make drivers simpler to handle, and their behaviour
more consistent.
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Reviewed-by: Sui Jingfeng <sui.jingfeng@linux.dev>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240527-kms-hdmi-connector-state-v15-1-c5af16c3aae2@kernel.org
Signed-off-by: Maxime Ripard <mripard@kernel.org>
percpu.h depends on smp.h, but doesn't include it directly because of
circular header dependency issues; percpu.h is needed in a bunch of low
level headers.
This fixes a randconfig build error on mips:
include/linux/alloc_tag.h: In function '__alloc_tag_ref_set':
include/asm-generic/percpu.h:31:40: error: implicit declaration of function 'raw_smp_processor_id' [-Werror=implicit-function-declaration]
Reported-by: kernel test robot <lkp@intel.com>
Fixes: 24e44cc22a ("mm: percpu: enable per-cpu allocation tagging")
Closes: https://lore.kernel.org/oe-kbuild-all/202405210052.DIrMXJNz-lkp@intel.com/
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull smb client fixes from Steve French:
- two important netfs integration fixes - including for a data
corruption and also fixes for multiple xfstests
- reenable swap support over SMB3
* tag '6.10-rc-smb3-fixes-part2' of git://git.samba.org/sfrench/cifs-2.6:
cifs: Fix missing set of remote_i_size
cifs: Fix smb3_insert_range() to move the zero_point
cifs: update internal version number
smb3: reenable swapfiles over SMB3 mounts
Pull misc fixes from Andrew Morton:
"16 hotfixes, 11 of which are cc:stable.
A few nilfs2 fixes, the remainder are for MM: a couple of selftests
fixes, various singletons fixing various issues in various parts"
* tag 'mm-hotfixes-stable-2024-05-25-09-13' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm:
mm/ksm: fix possible UAF of stable_node
mm/memory-failure: fix handling of dissolved but not taken off from buddy pages
mm: /proc/pid/smaps_rollup: avoid skipping vma after getting mmap_lock again
nilfs2: fix potential hang in nilfs_detach_log_writer()
nilfs2: fix unexpected freezing of nilfs_segctor_sync()
nilfs2: fix use-after-free of timer for log writer thread
selftests/mm: fix build warnings on ppc64
arm64: patching: fix handling of execmem addresses
selftests/mm: compaction_test: fix bogus test success and reduce probability of OOM-killer invocation
selftests/mm: compaction_test: fix incorrect write of zero to nr_hugepages
selftests/mm: compaction_test: fix bogus test success on Aarch64
mailmap: update email address for Satya Priya
mm/huge_memory: don't unpoison huge_zero_folio
kasan, fortify: properly rename memintrinsics
lib: add version into /proc/allocinfo output
mm/vmalloc: fix vmalloc which may return null if called with __GFP_NOFAIL
Pull x86 fixes from Ingo Molnar:
- Fix regressions of the new x86 CPU VFM (vendor/family/model)
enumeration/matching code
- Fix crash kernel detection on buggy firmware with
non-compliant ACPI MADT tables
- Address Kconfig warning
* tag 'x86-urgent-2024-05-25' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/cpu: Fix x86_match_cpu() to match just X86_VENDOR_INTEL
crypto: x86/aes-xts - switch to new Intel CPU model defines
x86/topology: Handle bogus ACPI tables correctly
x86/kconfig: Select ARCH_WANT_FRAME_POINTERS again when UNWINDER_FRAME_POINTER=y
Pull drm fixes from Dave Airlie:
"Some fixes for the end of the merge window, mostly amdgpu and panthor,
with one nouveau uAPI change that fixes a bad decision we made a few
months back.
nouveau:
- fix bo metadata uAPI for vm bind
panthor:
- Fixes for panthor's heap logical block.
- Reset on unrecoverable fault
- Fix VM references.
- Reset fix.
xlnx:
- xlnx compile and doc fixes.
amdgpu:
- Handle vbios table integrated info v2.3
amdkfd:
- Handle duplicate BOs in reserve_bo_and_cond_vms
- Handle memory limitations on small APUs
dp/mst:
- MST null deref fix.
bridge:
- Don't let next bridge create connector in adv7511 to make probe
work"
* tag 'drm-next-2024-05-25' of https://gitlab.freedesktop.org/drm/kernel:
drm/amdgpu/atomfirmware: add intergrated info v2.3 table
drm/mst: Fix NULL pointer dereference at drm_dp_add_payload_part2
drm/amdkfd: Let VRAM allocations go to GTT domain on small APUs
drm/amdkfd: handle duplicate BOs in reserve_bo_and_cond_vms
drm/bridge: adv7511: Attach next bridge without creating connector
drm/buddy: Fix the warn on's during force merge
drm/nouveau: use tile_mode and pte_kind for VM_BIND bo allocations
drm/panthor: Call panthor_sched_post_reset() even if the reset failed
drm/panthor: Reset the FW VM to NULL on unplug
drm/panthor: Keep a ref to the VM at the panthor_kernel_bo level
drm/panthor: Force an immediate reset on unrecoverable faults
drm/panthor: Document drm_panthor_tiler_heap_destroy::handle validity constraints
drm/panthor: Fix an off-by-one in the heap context retrieval logic
drm/panthor: Relax the constraints on the tiler chunk size
drm/panthor: Make sure the tiler initial/max chunks are consistent
drm/panthor: Fix tiler OOM handling to allow incremental rendering
drm: xlnx: zynqmp_dpsub: Fix compilation error
drm: xlnx: zynqmp_dpsub: Fix few function comments
Pull more mm updates from Andrew Morton:
"Jeff Xu's implementation of the mseal() syscall"
* tag 'mm-stable-2024-05-24-11-49' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm:
selftest mm/mseal read-only elf memory segment
mseal: add documentation
selftest mm/mseal memory sealing
mseal: add mseal syscall
mseal: wire up mseal syscall
After commit 69d4c0d321 ("entry, kasan, x86: Disallow overriding mem*()
functions") and the follow-up fixes, with CONFIG_FORTIFY_SOURCE enabled,
even though the compiler instruments meminstrinsics by generating calls to
__asan/__hwasan_ prefixed functions, FORTIFY_SOURCE still uses
uninstrumented memset/memmove/memcpy as the underlying functions.
As a result, KASAN cannot detect bad accesses in memset/memmove/memcpy.
This also makes KASAN tests corrupt kernel memory and cause crashes.
To fix this, use __asan_/__hwasan_memset/memmove/memcpy as the underlying
functions whenever appropriate. Do this only for the instrumented code
(as indicated by __SANITIZE_ADDRESS__).
Link: https://lkml.kernel.org/r/20240517130118.759301-1-andrey.konovalov@linux.dev
Fixes: 69d4c0d321 ("entry, kasan, x86: Disallow overriding mem*() functions")
Fixes: 51287dcb00 ("kasan: emit different calls for instrumentable memintrinsics")
Fixes: 36be5cba99 ("kasan: treat meminstrinsic as builtins in uninstrumented files")
Signed-off-by: Andrey Konovalov <andreyknvl@gmail.com>
Reported-by: Erhard Furtner <erhard_f@mailbox.org>
Reported-by: Nico Pache <npache@redhat.com>
Closes: https://lore.kernel.org/all/20240501144156.17e65021@outsider.home/
Reviewed-by: Marco Elver <elver@google.com>
Tested-by: Nico Pache <npache@redhat.com>
Acked-by: Nico Pache <npache@redhat.com>
Cc: Alexander Potapenko <glider@google.com>
Cc: Andrey Ryabinin <ryabinin.a.a@gmail.com>
Cc: Daniel Axtens <dja@axtens.net>
Cc: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Pull more RISC-V updates from Palmer Dabbelt:
- The compression format used for boot images is now configurable at
build time, and these formats are shown in `make help`
- access_ok() has been optimized
- A pair of performance bugs have been fixed in the uaccess handlers
- Various fixes and cleanups, including one for the IMSIC build failure
and one for the early-boot ftrace illegal NOPs bug
* tag 'riscv-for-linus-6.10-mw2' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
riscv: Fix early ftrace nop patching
irqchip: riscv-imsic: Fixup riscv_ipi_set_virq_range() conflict
riscv: selftests: Add signal handling vector tests
riscv: mm: accelerate pagefault when badaccess
riscv: uaccess: Relax the threshold for fast path
riscv: uaccess: Allow the last potential unrolled copy
riscv: typo in comment for get_f64_reg
Use bool value in set_cpu_online()
riscv: selftests: Add hwprobe binaries to .gitignore
riscv: stacktrace: fixed walk_stackframe()
ftrace: riscv: move from REGS to ARGS
riscv: do not select MODULE_SECTIONS by default
riscv: show help string for riscv-specific targets
riscv: make image compression configurable
riscv: cpufeature: Fix extension subset checking
riscv: cpufeature: Fix thead vector hwcap removal
riscv: rewrite __kernel_map_pages() to fix sleeping in invalid context
riscv: force PAGE_SIZE linear mapping if debug_pagealloc is enabled
riscv: Define TASK_SIZE_MAX for __access_ok()
riscv: Remove PGDIR_SIZE_L3 and TASK_SIZE_MIN
Pull sound fixes from Takashi Iwai:
"A collection of small fixes for 6.10-rc1. Most of changes are various
device-specific fixes and quirks, while there are a few small changes
in ALSA core timer and module / built-in fixes"
* tag 'sound-fix-6.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda/realtek: fix mute/micmute LEDs don't work for ProBook 440/460 G11.
ALSA: core: Enable proc module when CONFIG_MODULES=y
ALSA: core: Fix NULL module pointer assignment at card init
ALSA: hda/realtek: Enable headset mic of JP-IK LEAP W502 with ALC897
ASoC: dt-bindings: stm32: Ensure compatible pattern matches whole string
ASoC: tas2781: Fix wrong loading calibrated data sequence
ASoC: tas2552: Add TX path for capturing AUDIO-OUT data
ALSA: usb-audio: Fix for sampling rates support for Mbox3
Documentation: sound: Fix trailing whitespaces
ALSA: timer: Set lower bound of start tick time
ASoC: codecs: ES8326: solve hp and button detect issue
ASoC: rt5645: mic-in detection threshold modification
ASoC: Intel: sof_sdw_rt_sdca_jack_common: Use name_prefix for `-sdca` detection
The new mseal() is an syscall on 64 bit CPU, and with following signature:
int mseal(void addr, size_t len, unsigned long flags)
addr/len: memory range.
flags: reserved.
mseal() blocks following operations for the given memory range.
1> Unmapping, moving to another location, and shrinking the size,
via munmap() and mremap(), can leave an empty space, therefore can
be replaced with a VMA with a new set of attributes.
2> Moving or expanding a different VMA into the current location,
via mremap().
3> Modifying a VMA via mmap(MAP_FIXED).
4> Size expansion, via mremap(), does not appear to pose any specific
risks to sealed VMAs. It is included anyway because the use case is
unclear. In any case, users can rely on merging to expand a sealed VMA.
5> mprotect() and pkey_mprotect().
6> Some destructive madvice() behaviors (e.g. MADV_DONTNEED) for anonymous
memory, when users don't have write permission to the memory. Those
behaviors can alter region contents by discarding pages, effectively a
memset(0) for anonymous memory.
Following input during RFC are incooperated into this patch:
Jann Horn: raising awareness and providing valuable insights on the
destructive madvise operations.
Linus Torvalds: assisting in defining system call signature and scope.
Liam R. Howlett: perf optimization.
Theo de Raadt: sharing the experiences and insight gained from
implementing mimmutable() in OpenBSD.
Finally, the idea that inspired this patch comes from Stephen Röttger's
work in Chrome V8 CFI.
[jeffxu@chromium.org: add branch prediction hint, per Pedro]
Link: https://lkml.kernel.org/r/20240423192825.1273679-2-jeffxu@chromium.org
Link: https://lkml.kernel.org/r/20240415163527.626541-3-jeffxu@chromium.org
Signed-off-by: Jeff Xu <jeffxu@chromium.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Liam R. Howlett <Liam.Howlett@oracle.com>
Cc: Pedro Falcato <pedro.falcato@gmail.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Guenter Roeck <groeck@chromium.org>
Cc: Jann Horn <jannh@google.com>
Cc: Jeff Xu <jeffxu@google.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Jorge Lucangeli Obes <jorgelo@chromium.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Matthew Wilcox (Oracle) <willy@infradead.org>
Cc: Muhammad Usama Anjum <usama.anjum@collabora.com>
Cc: Pedro Falcato <pedro.falcato@gmail.com>
Cc: Stephen Röttger <sroettger@google.com>
Cc: Suren Baghdasaryan <surenb@google.com>
Cc: Amer Al Shanawany <amer.shanawany@gmail.com>
Cc: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Cc: Shuah Khan <shuah@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Patch series "Introduce mseal", v10.
This patchset proposes a new mseal() syscall for the Linux kernel.
In a nutshell, mseal() protects the VMAs of a given virtual memory range
against modifications, such as changes to their permission bits.
Modern CPUs support memory permissions, such as the read/write (RW) and
no-execute (NX) bits. Linux has supported NX since the release of kernel
version 2.6.8 in August 2004 [1]. The memory permission feature improves
the security stance on memory corruption bugs, as an attacker cannot
simply write to arbitrary memory and point the code to it. The memory
must be marked with the X bit, or else an exception will occur.
Internally, the kernel maintains the memory permissions in a data
structure called VMA (vm_area_struct). mseal() additionally protects the
VMA itself against modifications of the selected seal type.
Memory sealing is useful to mitigate memory corruption issues where a
corrupted pointer is passed to a memory management system. For example,
such an attacker primitive can break control-flow integrity guarantees
since read-only memory that is supposed to be trusted can become writable
or .text pages can get remapped. Memory sealing can automatically be
applied by the runtime loader to seal .text and .rodata pages and
applications can additionally seal security critical data at runtime. A
similar feature already exists in the XNU kernel with the
VM_FLAGS_PERMANENT [3] flag and on OpenBSD with the mimmutable syscall
[4]. Also, Chrome wants to adopt this feature for their CFI work [2] and
this patchset has been designed to be compatible with the Chrome use case.
Two system calls are involved in sealing the map: mmap() and mseal().
The new mseal() is an syscall on 64 bit CPU, and with following signature:
int mseal(void addr, size_t len, unsigned long flags)
addr/len: memory range.
flags: reserved.
mseal() blocks following operations for the given memory range.
1> Unmapping, moving to another location, and shrinking the size,
via munmap() and mremap(), can leave an empty space, therefore can
be replaced with a VMA with a new set of attributes.
2> Moving or expanding a different VMA into the current location,
via mremap().
3> Modifying a VMA via mmap(MAP_FIXED).
4> Size expansion, via mremap(), does not appear to pose any specific
risks to sealed VMAs. It is included anyway because the use case is
unclear. In any case, users can rely on merging to expand a sealed VMA.
5> mprotect() and pkey_mprotect().
6> Some destructive madvice() behaviors (e.g. MADV_DONTNEED) for anonymous
memory, when users don't have write permission to the memory. Those
behaviors can alter region contents by discarding pages, effectively a
memset(0) for anonymous memory.
The idea that inspired this patch comes from Stephen Röttger’s work in
V8 CFI [5]. Chrome browser in ChromeOS will be the first user of this
API.
Indeed, the Chrome browser has very specific requirements for sealing,
which are distinct from those of most applications. For example, in the
case of libc, sealing is only applied to read-only (RO) or read-execute
(RX) memory segments (such as .text and .RELRO) to prevent them from
becoming writable, the lifetime of those mappings are tied to the lifetime
of the process.
Chrome wants to seal two large address space reservations that are managed
by different allocators. The memory is mapped RW- and RWX respectively
but write access to it is restricted using pkeys (or in the future ARM
permission overlay extensions). The lifetime of those mappings are not
tied to the lifetime of the process, therefore, while the memory is
sealed, the allocators still need to free or discard the unused memory.
For example, with madvise(DONTNEED).
However, always allowing madvise(DONTNEED) on this range poses a security
risk. For example if a jump instruction crosses a page boundary and the
second page gets discarded, it will overwrite the target bytes with zeros
and change the control flow. Checking write-permission before the discard
operation allows us to control when the operation is valid. In this case,
the madvise will only succeed if the executing thread has PKEY write
permissions and PKRU changes are protected in software by control-flow
integrity.
Although the initial version of this patch series is targeting the Chrome
browser as its first user, it became evident during upstream discussions
that we would also want to ensure that the patch set eventually is a
complete solution for memory sealing and compatible with other use cases.
The specific scenario currently in mind is glibc's use case of loading and
sealing ELF executables. To this end, Stephen is working on a change to
glibc to add sealing support to the dynamic linker, which will seal all
non-writable segments at startup. Once this work is completed, all
applications will be able to automatically benefit from these new
protections.
In closing, I would like to formally acknowledge the valuable
contributions received during the RFC process, which were instrumental in
shaping this patch:
Jann Horn: raising awareness and providing valuable insights on the
destructive madvise operations.
Liam R. Howlett: perf optimization.
Linus Torvalds: assisting in defining system call signature and scope.
Theo de Raadt: sharing the experiences and insight gained from
implementing mimmutable() in OpenBSD.
MM perf benchmarks
==================
This patch adds a loop in the mprotect/munmap/madvise(DONTNEED) to
check the VMAs’ sealing flag, so that no partial update can be made,
when any segment within the given memory range is sealed.
To measure the performance impact of this loop, two tests are developed.
[8]
The first is measuring the time taken for a particular system call,
by using clock_gettime(CLOCK_MONOTONIC). The second is using
PERF_COUNT_HW_REF_CPU_CYCLES (exclude user space). Both tests have
similar results.
The tests have roughly below sequence:
for (i = 0; i < 1000, i++)
create 1000 mappings (1 page per VMA)
start the sampling
for (j = 0; j < 1000, j++)
mprotect one mapping
stop and save the sample
delete 1000 mappings
calculates all samples.
Below tests are performed on Intel(R) Pentium(R) Gold 7505 @ 2.00GHz,
4G memory, Chromebook.
Based on the latest upstream code:
The first test (measuring time)
syscall__ vmas t t_mseal delta_ns per_vma %
munmap__ 1 909 944 35 35 104%
munmap__ 2 1398 1502 104 52 107%
munmap__ 4 2444 2594 149 37 106%
munmap__ 8 4029 4323 293 37 107%
munmap__ 16 6647 6935 288 18 104%
munmap__ 32 11811 12398 587 18 105%
mprotect 1 439 465 26 26 106%
mprotect 2 1659 1745 86 43 105%
mprotect 4 3747 3889 142 36 104%
mprotect 8 6755 6969 215 27 103%
mprotect 16 13748 14144 396 25 103%
mprotect 32 27827 28969 1142 36 104%
madvise_ 1 240 262 22 22 109%
madvise_ 2 366 442 76 38 121%
madvise_ 4 623 751 128 32 121%
madvise_ 8 1110 1324 215 27 119%
madvise_ 16 2127 2451 324 20 115%
madvise_ 32 4109 4642 534 17 113%
The second test (measuring cpu cycle)
syscall__ vmas cpu cmseal delta_cpu per_vma %
munmap__ 1 1790 1890 100 100 106%
munmap__ 2 2819 3033 214 107 108%
munmap__ 4 4959 5271 312 78 106%
munmap__ 8 8262 8745 483 60 106%
munmap__ 16 13099 14116 1017 64 108%
munmap__ 32 23221 24785 1565 49 107%
mprotect 1 906 967 62 62 107%
mprotect 2 3019 3203 184 92 106%
mprotect 4 6149 6569 420 105 107%
mprotect 8 9978 10524 545 68 105%
mprotect 16 20448 21427 979 61 105%
mprotect 32 40972 42935 1963 61 105%
madvise_ 1 434 497 63 63 115%
madvise_ 2 752 899 147 74 120%
madvise_ 4 1313 1513 200 50 115%
madvise_ 8 2271 2627 356 44 116%
madvise_ 16 4312 4883 571 36 113%
madvise_ 32 8376 9319 943 29 111%
Based on the result, for 6.8 kernel, sealing check adds
20-40 nano seconds, or around 50-100 CPU cycles, per VMA.
In addition, I applied the sealing to 5.10 kernel:
The first test (measuring time)
syscall__ vmas t tmseal delta_ns per_vma %
munmap__ 1 357 390 33 33 109%
munmap__ 2 442 463 21 11 105%
munmap__ 4 614 634 20 5 103%
munmap__ 8 1017 1137 120 15 112%
munmap__ 16 1889 2153 263 16 114%
munmap__ 32 4109 4088 -21 -1 99%
mprotect 1 235 227 -7 -7 97%
mprotect 2 495 464 -30 -15 94%
mprotect 4 741 764 24 6 103%
mprotect 8 1434 1437 2 0 100%
mprotect 16 2958 2991 33 2 101%
mprotect 32 6431 6608 177 6 103%
madvise_ 1 191 208 16 16 109%
madvise_ 2 300 324 24 12 108%
madvise_ 4 450 473 23 6 105%
madvise_ 8 753 806 53 7 107%
madvise_ 16 1467 1592 125 8 108%
madvise_ 32 2795 3405 610 19 122%
The second test (measuring cpu cycle)
syscall__ nbr_vma cpu cmseal delta_cpu per_vma %
munmap__ 1 684 715 31 31 105%
munmap__ 2 861 898 38 19 104%
munmap__ 4 1183 1235 51 13 104%
munmap__ 8 1999 2045 46 6 102%
munmap__ 16 3839 3816 -23 -1 99%
munmap__ 32 7672 7887 216 7 103%
mprotect 1 397 443 46 46 112%
mprotect 2 738 788 50 25 107%
mprotect 4 1221 1256 35 9 103%
mprotect 8 2356 2429 72 9 103%
mprotect 16 4961 4935 -26 -2 99%
mprotect 32 9882 10172 291 9 103%
madvise_ 1 351 380 29 29 108%
madvise_ 2 565 615 49 25 109%
madvise_ 4 872 933 61 15 107%
madvise_ 8 1508 1640 132 16 109%
madvise_ 16 3078 3323 245 15 108%
madvise_ 32 5893 6704 811 25 114%
For 5.10 kernel, sealing check adds 0-15 ns in time, or 10-30
CPU cycles, there is even decrease in some cases.
It might be interesting to compare 5.10 and 6.8 kernel
The first test (measuring time)
syscall__ vmas t_5_10 t_6_8 delta_ns per_vma %
munmap__ 1 357 909 552 552 254%
munmap__ 2 442 1398 956 478 316%
munmap__ 4 614 2444 1830 458 398%
munmap__ 8 1017 4029 3012 377 396%
munmap__ 16 1889 6647 4758 297 352%
munmap__ 32 4109 11811 7702 241 287%
mprotect 1 235 439 204 204 187%
mprotect 2 495 1659 1164 582 335%
mprotect 4 741 3747 3006 752 506%
mprotect 8 1434 6755 5320 665 471%
mprotect 16 2958 13748 10790 674 465%
mprotect 32 6431 27827 21397 669 433%
madvise_ 1 191 240 49 49 125%
madvise_ 2 300 366 67 33 122%
madvise_ 4 450 623 173 43 138%
madvise_ 8 753 1110 357 45 147%
madvise_ 16 1467 2127 660 41 145%
madvise_ 32 2795 4109 1314 41 147%
The second test (measuring cpu cycle)
syscall__ vmas cpu_5_10 c_6_8 delta_cpu per_vma %
munmap__ 1 684 1790 1106 1106 262%
munmap__ 2 861 2819 1958 979 327%
munmap__ 4 1183 4959 3776 944 419%
munmap__ 8 1999 8262 6263 783 413%
munmap__ 16 3839 13099 9260 579 341%
munmap__ 32 7672 23221 15549 486 303%
mprotect 1 397 906 509 509 228%
mprotect 2 738 3019 2281 1140 409%
mprotect 4 1221 6149 4929 1232 504%
mprotect 8 2356 9978 7622 953 423%
mprotect 16 4961 20448 15487 968 412%
mprotect 32 9882 40972 31091 972 415%
madvise_ 1 351 434 82 82 123%
madvise_ 2 565 752 186 93 133%
madvise_ 4 872 1313 442 110 151%
madvise_ 8 1508 2271 763 95 151%
madvise_ 16 3078 4312 1234 77 140%
madvise_ 32 5893 8376 2483 78 142%
From 5.10 to 6.8
munmap: added 250-550 ns in time, or 500-1100 in cpu cycle, per vma.
mprotect: added 200-750 ns in time, or 500-1200 in cpu cycle, per vma.
madvise: added 33-50 ns in time, or 70-110 in cpu cycle, per vma.
In comparison to mseal, which adds 20-40 ns or 50-100 CPU cycles, the
increase from 5.10 to 6.8 is significantly larger, approximately ten times
greater for munmap and mprotect.
When I discuss the mm performance with Brian Makin, an engineer who worked
on performance, it was brought to my attention that such performance
benchmarks, which measuring millions of mm syscall in a tight loop, may
not accurately reflect real-world scenarios, such as that of a database
service. Also this is tested using a single HW and ChromeOS, the data
from another HW or distribution might be different. It might be best to
take this data with a grain of salt.
This patch (of 5):
Wire up mseal syscall for all architectures.
Link: https://lkml.kernel.org/r/20240415163527.626541-1-jeffxu@chromium.org
Link: https://lkml.kernel.org/r/20240415163527.626541-2-jeffxu@chromium.org
Signed-off-by: Jeff Xu <jeffxu@chromium.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Liam R. Howlett <Liam.Howlett@oracle.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Guenter Roeck <groeck@chromium.org>
Cc: Jann Horn <jannh@google.com> [Bug #2]
Cc: Jeff Xu <jeffxu@google.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Jorge Lucangeli Obes <jorgelo@chromium.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Matthew Wilcox (Oracle) <willy@infradead.org>
Cc: Muhammad Usama Anjum <usama.anjum@collabora.com>
Cc: Pedro Falcato <pedro.falcato@gmail.com>
Cc: Stephen Röttger <sroettger@google.com>
Cc: Suren Baghdasaryan <surenb@google.com>
Cc: Amer Al Shanawany <amer.shanawany@gmail.com>
Cc: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Cc: Shuah Khan <shuah@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Pull NFS client updates from Trond Myklebust:
"Stable fixes:
- nfs: fix undefined behavior in nfs_block_bits()
- NFSv4.2: Fix READ_PLUS when server doesn't support OP_READ_PLUS
Bugfixes:
- Fix mixing of the lock/nolock and local_lock mount options
- NFSv4: Fixup smatch warning for ambiguous return
- NFSv3: Fix remount when using the legacy binary mount api
- SUNRPC: Fix the handling of expired RPCSEC_GSS contexts
- SUNRPC: fix the NFSACL RPC retries when soft mounts are enabled
- rpcrdma: fix handling for RDMA_CM_EVENT_DEVICE_REMOVAL
Features and cleanups:
- NFSv3: Use the atomic_open API to fix open(O_CREAT|O_TRUNC)
- pNFS/filelayout: S layout segment range in LAYOUTGET
- pNFS: rework pnfs_generic_pg_check_layout to check IO range
- NFSv2: Turn off enabling of NFS v2 by default"
* tag 'nfs-for-6.10-1' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
nfs: fix undefined behavior in nfs_block_bits()
pNFS: rework pnfs_generic_pg_check_layout to check IO range
pNFS/filelayout: check layout segment range
pNFS/filelayout: fixup pNfs allocation modes
rpcrdma: fix handling for RDMA_CM_EVENT_DEVICE_REMOVAL
NFS: Don't enable NFS v2 by default
NFS: Fix READ_PLUS when server doesn't support OP_READ_PLUS
sunrpc: fix NFSACL RPC retry on soft mount
SUNRPC: fix handling expired GSS context
nfs: keep server info for remounts
NFSv4: Fixup smatch warning for ambiguous return
NFS: make sure lock/nolock overriding local_lock mount option
NFS: add atomic_open for NFSv3 to handle O_TRUNC correctly.
pNFS/filelayout: Specify the layout segment range in LAYOUTGET
pNFS/filelayout: Remove the whole file layout requirement
Pull more block updates from Jens Axboe:
"Followup block updates, mostly due to NVMe being a bit late to the
party. But nothing major in there, so not a big deal.
In detail, this contains:
- NVMe pull request via Keith:
- Fabrics connection retries (Daniel, Hannes)
- Fabrics logging enhancements (Tokunori)
- RDMA delete optimization (Sagi)
- ublk DMA alignment fix (me)
- null_blk sparse warning fixes (Bart)
- Discard support for brd (Keith)
- blk-cgroup list corruption fixes (Ming)
- blk-cgroup stat propagation fix (Waiman)
- Regression fix for plugging stall with md (Yu)
- Misc fixes or cleanups (David, Jeff, Justin)"
* tag 'block-6.10-20240523' of git://git.kernel.dk/linux: (24 commits)
null_blk: fix null-ptr-dereference while configuring 'power' and 'submit_queues'
blk-throttle: remove unused struct 'avg_latency_bucket'
block: fix lost bio for plug enabled bio based device
block: t10-pi: add MODULE_DESCRIPTION()
blk-mq: add helper for checking if one CPU is mapped to specified hctx
blk-cgroup: Properly propagate the iostat update up the hierarchy
blk-cgroup: fix list corruption from reorder of WRITE ->lqueued
blk-cgroup: fix list corruption from resetting io stat
cdrom: rearrange last_media_change check to avoid unintentional overflow
nbd: Fix signal handling
nbd: Remove a local variable from nbd_send_cmd()
nbd: Improve the documentation of the locking assumptions
nbd: Remove superfluous casts
nbd: Use NULL to represent a pointer
brd: implement discard support
null_blk: Fix two sparse warnings
ublk_drv: set DMA alignment mask to 3
nvme-rdma, nvme-tcp: include max reconnects for reconnect logging
nvmet-rdma: Avoid o(n^2) loop in delete_ctrl
nvme: do not retry authentication failures
...
Pull regulator fixes from Mark Brown:
"A bunch of fixes that came in during the merge window.
Matti found several issues with some of the more complexly configured
Rohm regulators and the helpers they use and there were some errors in
the specification of tps6594 when regulators are grouped together"
* tag 'regulator-fix-v6.10-merge-window' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: tps6594-regulator: Correct multi-phase configuration
regulator: tps6287x: Force writing VSEL bit
regulator: pickable ranges: don't always cache vsel
regulator: rohm-regulator: warn if unsupported voltage is set
regulator: bd71828: Don't overwrite runtime voltages
Pull tracing cleanup from Steven Rostedt:
"Remove second argument of __assign_str()
The __assign_str() macro logic of the TRACE_EVENT() macro was
optimized so that it no longer needs the second argument. The
__assign_str() is always matched with __string() field that takes a
field name and the source for that field:
__string(field, source)
The TRACE_EVENT() macro logic will save off the source value and then
use that value to copy into the ring buffer via the __assign_str().
Before commit c1fa617cae ("tracing: Rework __assign_str() and
__string() to not duplicate getting the string"), the __assign_str()
needed the second argument which would perform the same logic as the
__string() source parameter did. Not only would this add overhead, but
it was error prone as if the __assign_str() source produced something
different, it may not have allocated enough for the string in the ring
buffer (as the __string() source was used to determine how much to
allocate)
Now that the __assign_str() just uses the same string that was used in
__string() it no longer needs the source parameter. It can now be
removed"
* tag 'trace-assign-str-v6.10' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace:
tracing/treewide: Remove second parameter of __assign_str()
Pull virtio updates from Michael Tsirkin:
"Several new features here:
- virtio-net is finally supported in vduse
- virtio (balloon and mem) interaction with suspend is improved
- vhost-scsi now handles signals better/faster
And fixes, cleanups all over the place"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost: (48 commits)
virtio-pci: Check if is_avq is NULL
virtio: delete vq in vp_find_vqs_msix() when request_irq() fails
MAINTAINERS: add Eugenio Pérez as reviewer
vhost-vdpa: Remove usage of the deprecated ida_simple_xx() API
vp_vdpa: don't allocate unused msix vectors
sound: virtio: drop owner assignment
fuse: virtio: drop owner assignment
scsi: virtio: drop owner assignment
rpmsg: virtio: drop owner assignment
nvdimm: virtio_pmem: drop owner assignment
wifi: mac80211_hwsim: drop owner assignment
vsock/virtio: drop owner assignment
net: 9p: virtio: drop owner assignment
net: virtio: drop owner assignment
net: caif: virtio: drop owner assignment
misc: nsm: drop owner assignment
iommu: virtio: drop owner assignment
drm/virtio: drop owner assignment
gpio: virtio: drop owner assignment
firmware: arm_scmi: virtio: drop owner assignment
...
Pull more non-mm updates from Andrew Morton:
- A series ("kbuild: enable more warnings by default") from Arnd
Bergmann which enables a number of additional build-time warnings. We
fixed all the fallout which we could find, there may still be a few
stragglers.
- Samuel Holland has developed the series "Unified cross-architecture
kernel-mode FPU API". This does a lot of consolidation of
per-architecture kernel-mode FPU usage and enables the use of newer
AMD GPUs on RISC-V.
- Tao Su has fixed some selftests build warnings in the series
"Selftests: Fix compilation warnings due to missing _GNU_SOURCE
definition".
- This pull also includes a nilfs2 fixup from Ryusuke Konishi.
* tag 'mm-nonmm-stable-2024-05-22-17-30' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm: (23 commits)
nilfs2: make block erasure safe in nilfs_finish_roll_forward()
selftests/harness: use 1024 in place of LINE_MAX
Revert "selftests/harness: remove use of LINE_MAX"
selftests/fpu: allow building on other architectures
selftests/fpu: move FP code to a separate translation unit
drm/amd/display: use ARCH_HAS_KERNEL_FPU_SUPPORT
drm/amd/display: only use hard-float, not altivec on powerpc
riscv: add support for kernel-mode FPU
x86: implement ARCH_HAS_KERNEL_FPU_SUPPORT
powerpc: implement ARCH_HAS_KERNEL_FPU_SUPPORT
LoongArch: implement ARCH_HAS_KERNEL_FPU_SUPPORT
lib/raid6: use CC_FLAGS_FPU for NEON CFLAGS
arm64: crypto: use CC_FLAGS_FPU for NEON CFLAGS
arm64: implement ARCH_HAS_KERNEL_FPU_SUPPORT
ARM: crypto: use CC_FLAGS_FPU for NEON CFLAGS
ARM: implement ARCH_HAS_KERNEL_FPU_SUPPORT
arch: add ARCH_HAS_KERNEL_FPU_SUPPORT
x86/fpu: fix asm/fpu/types.h include guard
kbuild: enable -Wcast-function-type-strict unconditionally
kbuild: enable -Wformat-truncation on clang
...
Pull more mm updates from Andrew Morton:
"A series from Dave Chinner which cleans up and fixes the handling of
nested allocations within stackdepot and page-owner"
* tag 'mm-stable-2024-05-22-17-22' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm:
mm/page-owner: use gfp_nested_mask() instead of open coded masking
stackdepot: use gfp_nested_mask() instead of open coded masking
mm: lift gfp_kmemleak_mask() to gfp.h
With the rework of how the __string() handles dynamic strings where it
saves off the source string in field in the helper structure[1], the
assignment of that value to the trace event field is stored in the helper
value and does not need to be passed in again.
This means that with:
__string(field, mystring)
Which use to be assigned with __assign_str(field, mystring), no longer
needs the second parameter and it is unused. With this, __assign_str()
will now only get a single parameter.
There's over 700 users of __assign_str() and because coccinelle does not
handle the TRACE_EVENT() macro I ended up using the following sed script:
git grep -l __assign_str | while read a ; do
sed -e 's/\(__assign_str([^,]*[^ ,]\) *,[^;]*/\1)/' $a > /tmp/test-file;
mv /tmp/test-file $a;
done
I then searched for __assign_str() that did not end with ';' as those
were multi line assignments that the sed script above would fail to catch.
Note, the same updates will need to be done for:
__assign_str_len()
__assign_rel_str()
__assign_rel_str_len()
I tested this with both an allmodconfig and an allyesconfig (build only for both).
[1] https://lore.kernel.org/linux-trace-kernel/20240222211442.634192653@goodmis.org/
Link: https://lore.kernel.org/linux-trace-kernel/20240516133454.681ba6a0@rorschach.local.home
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Julia Lawall <Julia.Lawall@inria.fr>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Acked-by: Christian König <christian.koenig@amd.com> for the amdgpu parts.
Acked-by: Thomas Hellström <thomas.hellstrom@linux.intel.com> #for
Acked-by: Rafael J. Wysocki <rafael@kernel.org> # for thermal
Acked-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Darrick J. Wong <djwong@kernel.org> # xfs
Tested-by: Guenter Roeck <linux@roeck-us.net>
This commit replaces riscv's support for FTRACE_WITH_REGS with support
for FTRACE_WITH_ARGS. This is required for the ongoing effort to stop
relying on stop_machine() for RISCV's implementation of ftrace.
The main relevant benefit that this change will bring for the above
use-case is that now we don't have separate ftrace_caller and
ftrace_regs_caller trampolines. This will allow the callsite to call
ftrace_caller by modifying a single instruction. Now the callsite can
do something similar to:
When not tracing: | When tracing:
func: func:
auipc t0, ftrace_caller_top auipc t0, ftrace_caller_top
nop <=========<Enable/Disable>=========> jalr t0, ftrace_caller_bottom
[...] [...]
The above assumes that we are dropping the support of calling a direct
trampoline from the callsite. We need to drop this as the callsite can't
change the target address to call, it can only enable/disable a call to
a preset target (ftrace_caller in the above diagram). We can later optimize
this by calling an intermediate dispatcher trampoline before ftrace_caller.
Currently, ftrace_regs_caller saves all CPU registers in the format of
struct pt_regs and allows the tracer to modify them. We don't need to
save all of the CPU registers because at function entry only a subset of
pt_regs is live:
|----------+----------+---------------------------------------------|
| Register | ABI Name | Description |
|----------+----------+---------------------------------------------|
| x1 | ra | Return address for traced function |
| x2 | sp | Stack pointer |
| x5 | t0 | Return address for ftrace_caller trampoline |
| x8 | s0/fp | Frame pointer |
| x10-11 | a0-1 | Function arguments/return values |
| x12-17 | a2-7 | Function arguments |
|----------+----------+---------------------------------------------|
See RISCV calling convention[1] for the above table.
Saving just the live registers decreases the amount of stack space
required from 288 Bytes to 112 Bytes.
Basic testing was done with this on the VisionFive 2 development board.
Note:
- Moving from REGS to ARGS will mean that RISCV will stop supporting
KPROBES_ON_FTRACE as it requires full pt_regs to be saved.
- KPROBES_ON_FTRACE will be supplanted by FPROBES see [2].
[1] https://riscv.org/wp-content/uploads/2015/01/riscv-calling.pdf
[2] https://lore.kernel.org/all/170887410337.564249.6360118840946697039.stgit@devnote2/
Signed-off-by: Puranjay Mohan <puranjay@kernel.org>
Tested-by: Björn Töpel <bjorn@rivosinc.com>
Reviewed-by: Björn Töpel <bjorn@rivosinc.com>
Link: https://lore.kernel.org/r/20240405142453.4187-1-puranjay@kernel.org
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
