RTC lives on the chip's base register page. Add the relevant register
definitions and implement a basic set/read time functionality. Tested
with the samsung,coreprimevelte smartphone which contains this PMIC and
whose vendor kernel tree has also served as the sole reference for this.
Signed-off-by: Karel Balej <balejk@matfyz.cz>
Acked-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20241012193345.18594-2-balejk@matfyz.cz
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The RTC IP (RTCA-3) available on the Renesas RZ/G3S SoC has calendar count
mode and binary count mode (selectable though RCR2.CNTMD) capabilities,
alarm capabilities, clock error correction capabilities. It can generate
alarm, period, carry interrupts.
Add a driver for RTCA-3 IP. The driver implements calendar count mode (as
the conversion b/w RTC and system time is simpler, done with bcd2bin(),
bin2bcd()), read and set time, read and set alarm, read and set
an offset.
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Link: https://lore.kernel.org/r/20241030110120.332802-6-claudiu.beznea.uj@bp.renesas.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Pull RTC updates from Alexandre Belloni:
"More conversions of DT bindings to yaml. There is one new driver, for
the DFRobot SD2405AL and support for important features of the stm32
RTC. Summary:
New driver:
- DFRobot SD2405AL
Drivers:
- stm32: add alarm A out and LSCO support
- sun6i: disable automatic clock input switching
- m48t59: set range"
* tag 'rtc-6.12' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux:
rtc: rc5t619: use proper module tables
rtc: m48t59: set range
dt-bindings: rtc: microcrystal,rv3028: add #clock-cells property
rtc: m48t59: Remove division condition with direct comparison
rtc: at91sam9: fix OF node leak in probe() error path
rtc: sun6i: disable automatic clock input switching
dt-bindings: rtc: Drop non-trivial duplicate compatibles
dt-bindings: vendor-prefixes: Add DFRobot.
dt-bindings: rtc: Add support for SD2405AL.
rtc: Add driver for SD2405AL
rtc: s35390a: Drop vendorless compatible string from match table
rtc: twl: convert comma to semicolon
dt-bindings: rtc: sprd,sc2731-rtc: convert to YAML
rtc: stm32: add alarm A out feature
rtc: stm32: add Low Speed Clock Output (LSCO) support
rtc: stm32: add pinctrl and pinmux interfaces
dt-bindings: rtc: stm32: describe pinmux nodes
RTC is able to output on a pin the "LSE" internal clock.
STM32 RTC is now registered as a clock provider.
It provides rtc_lsco clock, that means RTC_LSCO is output on either
RTC_OUT1 or RTC_OUT2_RMP, depending on pinmux DT property.
The clock is marked as CLK_IGNORE_UNUSED and CLK_IS_CRITICAL because
RTC_LSCO can be early required by devices needed it to init.
Add LSCO in pinmux functions.
Add "stm32_rtc_clean_outs" to disable LSCO. As RTC is part of "backup"
power domain, it is not reset during shutdown or reboot. So force LSCO
disable at probe.
Co-developed-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Signed-off-by: Valentin Caron <valentin.caron@foss.st.com>
Link: https://lore.kernel.org/r/20240722160022.454226-4-valentin.caron@foss.st.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The ma35d1 rtc controller provides real-time and calendar messaging
capabilities. It supports programmable time tick and alarm match
interrupts. The time and calendar messages are expressed in BCD format.
This driver supports the built-in rtc controller of the ma35d1. It
enables setting and reading the rtc time and configuring and reading
the rtc alarm.
Signed-off-by: Jacky Huang <ychuang3@nuvoton.com>
Link: https://lore.kernel.org/r/20230925070251.28-4-ychuang570808@gmail.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
This RTC is very similar in functionality to the PCF2127/29.
Basically it:
-supports two new control registers at offsets 4 and 5
-supports a new reset register (not implemented in this driver)
-supports 4 tamper detection functions instead of 1
-has no nvmem (like the PCF2129)
-has two output interrupt pins
Because of that, most of the register addresses are very different,
although they still follow the same layout. For example, the tamper
registers have a different base address, but the offsets are all the same.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20230622145800.2442116-12-hugo@hugovil.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Pull RTC updates from Alexandre Belloni:
"The isl1208 dirver was reworked tobe able to work as part of an MFD.
All the Loongson chips are now supported through a new driver, the old
one is removed.
Summary:
Subsystem:
- Switch i2c drivers back to use .probe()
- Constify pointers to hwmon_channel_info
New driver:
- Loongson on chip RTC, replacing the Loongson 1 only driver
Drivers:
- isl1208: cleanup and support for RAA215300
- st-lpc: cleanups
- stm32: fix wakeup"
* tag 'rtc-6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux: (21 commits)
rtc: Add rtc driver for the Loongson family chips
rtc: Remove the Loongson-1 RTC driver
dt-bindings: rtc: Split loongson,ls2x-rtc into SoC-based compatibles
rtc: rv3028: make rv3028 probeable from userspace
rtc: isl1208: Add support for the built-in RTC on the PMIC RAA215300
rtc: isl1208: Add isl1208_set_xtoscb()
rtc: isl1208: Drop enum isl1208_id and split isl1208_configs[]
rtc: isl1208: Make similar I2C and DT-based matching table
rtc: isl1208: Drop name variable
dt-bindings: rtc: isil,isl1208: Document clock and clock-names properties
dt-bindings: rtc: isl1208: Convert to json-schema
rtc: st-lpc: Simplify clk handling in st_rtc_probe()
rtc: st-lpc: Release some resources in st_rtc_probe() in case of error
rtc: stm32: remove dedicated wakeup management
dt-bindings: rtc: restrict node name suffixes
rtc: add HAS_IOPORT dependencies
rtc: Switch i2c drivers back to use .probe()
rtc: rv3032: constify pointers to hwmon_channel_info
rtc: isl12022: constify pointers to hwmon_channel_info
rtc: ds3232: constify pointers to hwmon_channel_info
...
Pull RTC updates from Alexandre Belloni:
"A few drivers got some nice cleanups and a new driver are making the
bulk of the changes.
Subsystem:
- allow rtc_read_alarm without read_alarm callback
New driver:
- NXP BBNSM module RTC
Drivers:
- use IRQ flags from fwnode when available
- abx80x: nvmem support
- brcmstb-waketimer: add non-wake alarm support
- ingenic: provide CLK32K clock
- isl12022: cleanups
- moxart: switch to using gpiod API
- pcf85363: allow setting quartz load
- pm8xxx: cleanups and support for setting time
- rv3028, rv3032: add ACPI support"
* tag 'rtc-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux: (64 commits)
rtc: pm8xxx: add support for nvmem offset
dt-bindings: rtc: qcom-pm8xxx: add nvmem-cell offset
rtc: abx80x: Add nvmem support
rtc: rx6110: Remove unused of_gpio,h
rtc: efi: Avoid spamming the log on RTC read failure
rtc: isl12022: sort header inclusion alphabetically
rtc: isl12022: Join string literals back
rtc: isl12022: Drop unneeded OF guards and of_match_ptr()
rtc: isl12022: Explicitly use __le16 type for ISL12022_REG_TEMP_L
rtc: isl12022: Get rid of unneeded private struct isl12022
rtc: pcf85363: add support for the quartz-load-femtofarads property
dt-bindings: rtc: nxp,pcf8563: move pcf85263/pcf85363 to a dedicated binding
rtc: allow rtc_read_alarm without read_alarm callback
rtc: rv3032: add ACPI support
rtc: rv3028: add ACPI support
rtc: bbnsm: Add the bbnsm rtc support
rtc: jz4740: Register clock provider for the CLK32K pin
rtc: jz4740: Use dev_err_probe()
rtc: jz4740: Use readl_poll_timeout
dt-bindings: rtc: Add #clock-cells property
...
On JZ4770 and JZ4780, the CLK32K pin is configurable. By default, it is
configured as a GPIO in input mode, and its value can be read through
GPIO PD14.
With this change, clients can now request the 32 kHz clock on the CLK32K
pin, through Device Tree. This clock is simply a pass-through of the
input oscillator's clock with enable/disable operations.
This will permit the WiFi/Bluetooth chip to work on the MIPS CI20 board,
which does source one of its clocks from the CLK32K pin.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20230129120442.22858-5-paul@crapouillou.net
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Pull MFD updates from Lee Jones:
"New Drivers:
- Add support for Ampere Computing SMpro
- Add support for TI TPS65219 PMIC
New Functionality:
- Add support for multiple devices of the same type; rk808
Fix-ups:
- Convert a bunch of I2C class drivers over to .probe_new()
- Remove superfluous includes; mc13xxx-*, palmas, timberdale
- Use correct includes for GPIO handling; madera-core
- Convert to GPIOD; twl6040
- Remove unused platform data handling; twl6040
- Device Tree changes; many
- Remove unused drivers; dm355evm_msp, davinci_voicecodec, htc-i2cpld
- Add support for modules; palmas
- Enable COMPILE_TEST support; intel_soc_pmic*
- Trivial: spelling / whitespace fixes; mc13xxx-spi
- Replace old PM helpers with new ones; many
- Convert deprecated mask_invert usage to unmask_base; many
- Use devm_*() calls; qcom_rpm
- MAINTAINER fix-ups
- Make use of improved / replaced APIs; palmas, fsl-imx25-tsadc,
stm32-lptimer, qcom_rpm, rohm-*
Bug Fixes:
- Add bounds / error checking; mt6360-core
- No sleeping inside critical sections; axp20x
- Fix missing dependencies; ROHM_BD957XMUF
- Repair error paths; qcom-pm8008"
* tag 'mfd-next-6.2' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (161 commits)
dt-bindings: mfd: da9062: Correct file name for watchdog
mfd: pm8008: Fix return value check in pm8008_probe()
mfd: rohm: Use dev_err_probe()
mfd: Drop obsolete dependencies on COMPILE_TEST
dt-bindings: mfd: da9062: Move IRQ to optional properties
mfd: qcom_rpm: Use devm_of_platform_populate() to simplify code
mfd: qcom_rpm: Fix an error handling path in qcom_rpm_probe()
mfd: stm32-lptimer: Use devm_platform_get_and_ioremap_resource()
mfd: rohm-bd9576: Convert to i2c's .probe_new()
mfd: fsl-imx25-tsadc: Use devm_platform_get_and_ioremap_resource()
dt-bindings: Fix maintainer email for a few ROHM ICs
mfd: palmas: Use device_get_match_data() to simplify the code
Input: Add tps65219 interrupt driven powerbutton
mfd: tps65219: Add driver for TI TPS65219 PMIC
mfd: bd957x: Fix Kconfig dependency on REGMAP_IRQ
mfd: wcd934x: Convert irq chip to config regs
mfd: tps65090: Replace irqchip mask_invert with unmask_base
mfd: sun4i-gpadc: Replace irqchip mask_invert with unmask_base
mfd: stpmic1: Fix swapped mask/unmask in irq chip
mfd: sprd-sc27xx-spi: Replace irqchip mask_invert with unmask_base
...
Since commit 0166dc11be ("of: make CONFIG_OF user selectable"), it
is possible to test-build any driver which depends on OF on any
architecture by explicitly selecting OF. Therefore depending on
COMPILE_TEST as an alternative is no longer needed.
It is actually better to always build such drivers with OF enabled,
so that the test builds are closer to how each driver will actually be
built on its intended target. Building them without OF may not test
much as the compiler will optimize out potentially large parts of the
code. In the worst case, this could even pop false positive warnings.
Dropping COMPILE_TEST here improves the quality of our testing and
avoids wasting time on non-existent issues.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20221124154359.039be06c@endymion.delvare
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The regmap abstraction allows us to avoid the private i2c transfer
helpers, and also offers some nice utility functions such as the
regmap_update_bits family.
While at it, simplify the code even more by not keeping track of
->write_enabled: rtc_set_time is not a hot path, so one extra i2c read
doesn't hurt (regmap_update_bits elides the write when the bits are
already as desired).
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Link: https://lore.kernel.org/r/20220921114624.3250848-9-linux@rasmusvillemoes.dk
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Introduce support for Texas Instruments Real Time Clock controller on
newer K3 family of SoCs such as AM62x.
The hardware module that is being supported is the "digital only"
version which doesn't have capability of external wakeup sources and
external power backup. However, for many practical applications, this
should suffice as RTC is operational across low power sequences.
The hardware block by itself is split into two distinct domains
internally to further reduce the power consumption with the actual
counter block and comparators clocked off a 32k clock source (which
based on SoC integration can be sourced by an external crystal) and an
register interface block which is driven by the bus clock. While optimal
from power perspective, it does create some complicated synchronizations
and sequences that one must be wary of in the driver handling.
Acked-by: Andrew Davis <afd@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Tested-by: Georgi Vlaev <g-vlaev@ti.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20220623170808.20998-3-nm@ti.com
