Merge the pmdomain fixes for v6.17-rc[n] into the next branch, to allow
them to get tested together with the new changes that are targeted for
v6.18.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In MT8195 power domain data array, set the KEEP_DEFAULT_OFF and
ACTIVE_WAKEUP flags for the AUDIO power domain entry to avoid
having this domain being on during boot sequence when unneeded.
Fixes: 0e789b491b ("pmdomain: core: Leave powered-on genpds on until sync_state")
Fixes: 13a4b7fb62 ("pmdomain: core: Leave powered-on genpds on until late_initcall_sync")
Signed-off-by: Louis-Alexis Eyraud <louisalexis.eyraud@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The round_rate() clk ops is deprecated, so migrate this driver from
round_rate() to determine_rate() using the Coccinelle semantic patch
appended to the "under-the-cut" portion of the patch.
Note that prior to running the Coccinelle,
airoha_cpu_pmdomain_clk_round() was renamed to
airoha_cpu_pmdomain_clk_round_rate().
Signed-off-by: Brian Masney <bmasney@redhat.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
New generation SoCs use a new RTFF Hardware to save power during
operation of various IPs, other than managing isolation of the
internal buck converters during powerup/down of power domains.
Since some of the power domains need different RTFF handling, add
a new scpys_rtff_type enumeration and hold the value for each
power domain in struct scpsys_domain_data.
If RTFF HW is available, the RTFF additional power sequences are
handled in scpsys_ctl_pwrseq_{on,off}().
Reviewed-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20250805074746.29457-9-angelogioacchino.delregno@collabora.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Some SoCs, and even some subsystems in the same SoC, may have the
logic for SRAM power-down inverted, as in, setting the bit means
"power down" and unsetting means "power up": this is because some
hardware subsystems use this as a power-lock indication and some
use this as a power down one (for example, usually, the modem ss
has it inverted!).
In preparation for adding support for power domains with inverted
SRAM_PDN bits, add a new MTK_SCPD_SRAM_PDN_INVERTED flag and check
for it in scpsys_sram_enable() and scpsys_sram_disable().
Reviewed-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20250805074746.29457-6-angelogioacchino.delregno@collabora.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In preparation to add support for new generation SoCs like MT8196,
MT6991 and other variants, which require to set bus protection on
different busses than the ones found on legacy chips, and to also
simplify and reduce memory footprint of this driver, refactor the
mechanism to retrieve and use the bus protection regmaps.
This is done by removing the three pointers to struct regmap from
struct scpsys_domain (allocated for each power domain) and moving
them to the main struct scpsys (allocated per driver instance) as
an array of pointers to regmap named **bus_prot.
That deprecates the old devicetree properties to grab phandles to
the three predefined busses (infracfg, infracfg-nao and smi) and
replaces it with the base property "access-controllers" that is
meant to be an array of phandles holding the same busses where
required (for now - for legacy SoCs).
The new bus protection phandles are indexed by the bus_prot_index
member of struct scpsys, used to map "bus type" (ex.: infra, smi,
etc) to the specific *bus_prot[x] element.
While the old per-power-domain regmap pointers were removed, the
support for old devicetree was retained by still checking if the
new property (in DT) and new-style declaration (in SoC specific
platform data) are both present at probe time.
If those are not present, a lookup for the old properties will be
done in all of the children of the power controller, and pointers
to regmaps will be retrieved with the old properties, but then
will be internally remapped to follow the new style regmap anyway
as to let this driver benefit of the memory footprint reduction.
Finally, it was necessary to change macros in mtk-pm-domains.h and
in mt8365-pm-domains.h to make use of the new style bus protection
declaration, as the actual HW block is now recognized not by flags
but by its own scpsys_bus_prot_block enumeration.
The BUS_PROT_(STA)_COMPONENT_{INFRA,INFRA_NAO,SMI} flags were also
removed since they are now unused, and because that enumeration was
initially meant to vary the logic of bus protection and not the bus
where work is performed, anyway!
Reviewed-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20250805074746.29457-5-angelogioacchino.delregno@collabora.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
A recent change to the syscon regmap API caused the MediaTek power
controller drivers to fail, as the required regmap could no longer be
retrieved. The error did not have an accompanying message, making the
failure less obvious. The aforementioned change has since been reverted.
Add error messages to all the regmap retrievals, thereby making all
error paths in scpsys_add_one_domain() have visible error messages.
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20250421090951.395467-1-wenst@chromium.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add Airoha CPU PM Domain support to control frequency and power of CPU
present on Airoha EN7581 SoC.
Frequency and power can be controlled with the use of the SMC command by
passing the performance state. The driver also expose a read-only clock
that expose the current CPU frequency with SMC command.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Link: https://lore.kernel.org/r/20250109131313.32317-1-ansuelsmth@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The MediaTek power domain driver contains a hack that assigns the device
node of the power domain to the struct device of the power domain
controller in order to use the devres regulator API.
Now that there is a proper OF-specific regulator API, and even a devres
version, replace the hack with proper code.
This change is incompatible with incomplete device trees. Instead of
assigning the dummy regulator in cases where the power domain requires
a supply but the device tree does not provide one, the driver will just
error out. This will be seen on the MT8390 EVK, which is missing
supplies for the IMG_VCORE and CAM_VCORE domains. And likely all the
MediaTek EVBs, which have no power domain supplies specified. This is
however the correct behavior. If the power domain's supply is missing,
then it should not work. Relying on other parts of the system to keep
the unattached regulator enabled is likely to break in ways less easier
to understand.
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Link: https://lore.kernel.org/r/20240930044525.2043884-4-wenst@chromium.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If the power domains are registered first with genpd and *after that*
the driver attempts to power them on in the probe sequence, then it is
possible that a race condition occurs if genpd tries to power them on
in the same time.
The same is valid for powering them off before unregistering them
from genpd.
Attempt to fix race conditions by first removing the domains from genpd
and *after that* powering down domains.
Also first power up the domains and *after that* register them
to genpd.
Fixes: 59b644b01c ("soc: mediatek: Add MediaTek SCPSYS power domains")
Signed-off-by: Eugen Hristev <eugen.hristev@collabora.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20231225133615.78993-1-eugen.hristev@collabora.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This updates the power domain to support WAY_EN operations. WAY_EN
operations on mt8365 are using a different component to check for the
acknowledgment, namely the infracfg-nao component. Also to enable a way
it the bit needs to be cleared while disabling a way needs a bit to be
set. To support these two operations two flags are added,
BUS_PROT_INVERTED and BUS_PROT_STA_COMPONENT_INFRA_NAO. Additionally
another regmap is created if the INFRA_NAO capability is set.
This operation is required by the mt8365 for the MM power domain.
Signed-off-by: Alexandre Bailon <abailon@baylibre.com>
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Alexandre Mergnat <amergnat@baylibre.com>
Tested-by: Alexandre Mergnat <amergnat@baylibre.com>
Link: https://lore.kernel.org/r/20230918093751.1188668-7-msp@baylibre.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
It has been pointed out that naming a subsystem "genpd" isn't very
self-explanatory and the acronym itself that means Generic PM Domain, is
known only by a limited group of people.
In a way to improve the situation, let's rename the subsystem to pmdomain,
which ideally should indicate that this is about so called Power Domains or
"PM domains" as we often also use within the Linux Kernel terminology.
Suggested-by: Rafael J. Wysocki <rafael@kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Rafael J. Wysocki <rafael@kernel.org>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20230912221127.487327-1-ulf.hansson@linaro.org
