Detect when PSE hardware is already configured (user byte == 42) and
skip hardware initialization to prevent power interruption to connected
devices during system reboots.
Previously, the driver would always reconfigure the PSE hardware on
probe, causing a port matrix reflash that resulted in temporary power
loss to all connected devices. This change maintains power continuity
by preserving existing configuration when the PSE has been previously
initialized.
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20251013-feature_pd692x0_reboot_keep_conf-v2-3-68ab082a93dd@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Cache the port matrix configuration in driver private data to enable
PSE controller reconfiguration. This refactoring separates device tree
parsing from hardware configuration application, allowing settings to be
reapplied without reparsing the device tree.
This refactoring is a prerequisite for preserving PSE configuration
across reboots to prevent power disruption to connected devices.
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20251013-feature_pd692x0_reboot_keep_conf-v2-2-68ab082a93dd@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Bringing a linked netdevsim device down and then up causes communication
failure because both interfaces lack carrier. Basically a ifdown/ifup on
the interface make the link broken.
Commit 3762ec05a9 ("netdevsim: add NAPI support") added supported
for NAPI, calling netif_carrier_off() in nsim_stop(). This patch
re-enables the carrier symmetrically on nsim_open(), in case the device
is linked and the peer is up.
Signed-off-by: Breno Leitao <leitao@debian.org>
Fixes: 3762ec05a9 ("netdevsim: add NAPI support")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20251014-netdevsim_fix-v2-1-53b40590dae1@debian.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
While associating, firmware needs the peer's receive capability
to calculate its own VHT transmit MCS. Currently, the host
sends this information via mcs->rx_mcs_set field, but firmware
actually reads it from mcs->tx_mcs_set field. This mismatch is
incorrect.
This issue has not caused failures so far because most peers
advertise identical TX and RX capabilities. Fix this by
assigning the value to tx_mcs_set as expected.
Additionally, the rate control mask is intended to limit our
transmit MCS, so it should also apply to the peer's receive
capability. Update the logic accordingly.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Fixes: d889913205 ("wifi: ath12k: driver for Qualcomm Wi-Fi 7 devices")
Signed-off-by: Baochen Qiang <baochen.qiang@oss.qualcomm.com>
Signed-off-by: Pradeep Kumar Chitrapu <quic_pradeepc@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Reviewed-by: Baochen Qiang <baochen.qiang@oss.qualcomm.com>
Link: https://patch.msgid.link/20251009211656.2386085-2-quic_pradeepc@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, in ext_rx_stats, the NSS value is taken directly from
the firmware, which results in incorrect mapping:
4x4, 3x3, 2x2, 1x1 SS are incorrectly updated as 3x3, 2x2,
1x1, 0x0 SS respectively.
Fix the issue by incrementing the NSS value by 1 while updating
the PPDU info to ensure accurate spatial stream statistics.
Remove the redundant +1 increment in the radiotap header when monitor
mode is enabled to prevent double counting.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.5-01651-QCAHKSWPL_SILICONZ-1
Signed-off-by: Thiraviyam Mariyappan <thiraviyam.mariyappan@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20251007133332.1092178-1-thiraviyam.mariyappan@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Mac80211 schedules CSA finalize work twice during a channel switch: first
during the reserved switch phase and again during the finalize phase.
The beacon content is updated only during the second schedule, which occurs
after the reserved switch completes. However, the ath12k driver attempts to
bring up the VDEV during the channel switch callback
(ath12k_mac_update_vif_chan()), which leads to premature installation of
stale beacon templates before the updated content is available.
This premature VDEV bring-up causes outdated beacon information to be
broadcast, which can result in updated channel parameters during the
transition. In MBSSID scenarios, this behavior is particularly problematic
because the transmitting interface's beacon must be updated before
non-transmitting interfaces are brought up. Failing to do so can lead to
beacon mismatches across interfaces.
Introduce a is_csa_in_progress flag to defer VDEV_UP until CSA finalize is
complete. Set this flag during the channel switch callback when CSA is
active. In bss_info_changed(), check this flag and issue VDEV_UP only
after the beacon template has been updated.
Ensure that in MBSSID cases, the transmitting interface is brought up
first, followed by all non-transmitting interfaces. This ordering makes
sure correct beacon propagation and avoids stale beacon installation
during CSA transitions.
Additionally, move the call to ath12k_mac_update_peer_puncturing_width()
before VDEV bring-up during CSA handling. This ensures that the puncturing
bitmap and bandwidth settings are applied before the VDEV is brought up.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Fixes: 8c6faa56bf ("wifi: ath12k: add MBSSID beacon support")
Signed-off-by: Aditya Kumar Singh <aditya.kumar.singh@oss.qualcomm.com>
Signed-off-by: Maharaja Kennadyrajan <maharaja.kennadyrajan@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250924134336.888-1-maharaja.kennadyrajan@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, packets received on the REO exception ring from
unassociated peers are of MSDU buffer type, while the driver expects
link descriptor type packets. These packets are not parsed further due
to a return check on packet type in ath12k_hal_desc_reo_parse_err(),
but the associated skb is not freed. This may lead to kernel
crashes and buffer leaks.
Hence to fix, update the RX error handler to explicitly drop
MSDU buffer type packets received on the REO exception ring.
This prevents further processing of invalid packets and ensures
stability in the RX error handling path.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Fixes: d889913205 ("wifi: ath12k: driver for Qualcomm Wi-Fi 7 devices")
Signed-off-by: Sarika Sharma <sarika.sharma@oss.qualcomm.com>
Reviewed-by: Baochen Qiang <baochen.qiang@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250930091551.3305312-2-sarika.sharma@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Hardware target implements an address space larger than that PCI BAR can
map. In order to be able to access the whole target address space, the BAR
space is split into 4 segments, of which the last 3, called windows, can
be dynamically mapped to the desired area. This is achieved by updating
window register with appropriate window value. Currently each time when
accessing a register that beyond ATH11K_PCI_WINDOW_START, host calculates
the window value and caches it after window update, this way next time
when accessing a register falling in the same window, host knows that the
window is already good hence no additional update needed.
However this mechanism breaks after global reset is triggered in
ath11k_pci_soc_global_reset(), because with global reset hardware resets
window register hence the window is not properly mapped any more. Current
host does nothing about this, as a result a subsequent register access may
not work as expected if it falls in a window same as before.
Although there is no obvious issue seen now, better to fix it to avoid
future problem. The fix is done by restoring the window register after
global reset.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.30
Fixes: d5c65159f2 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Signed-off-by: Baochen Qiang <baochen.qiang@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20251014-ath11k-reset-window-cache-v1-1-b85271b111dd@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, ath10k has a recovery check logic. It will wait for the
last recovery to finish by wait_for_completion_timeout();
But in SDIO scenarios, the recovery function may be invoked from
interrupt context, where long blocking waits are undesirable and can
lead to system instability.
Additionally, Linux’s ordered workqueue processes one task at a time.
If a previous recovery is still queued or executing, new triggers are
ignored. This prevents accurate tracking of consecutive failures and
delays transition to the WEDGED state.
To address this, move the recovery check logic into a different
workqueue.
Tested-on: QCA6174 hw3.2 PCI WLAN.RM.4.4.1-00288-QCARMSWPZ-1
Tested-on: QCA6174 hw3.2 SDIO WLAN.RMH.4.4.1-00189
Fixes: c256a94d1b ("wifi: ath10k: shutdown driver when hardware is unreliable")
Signed-off-by: Kang Yang <kang.yang@oss.qualcomm.com>
Reviewed-by: Baochen Qiang <baochen.qiang@oss.qualcomm.com>
Link: https://patch.msgid.link/20251014110757.155-1-kang.yang@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Fix several minor typos and grammatical errors in comments and log
(in fbnic firmware, PCI, and time modules)
Changes include:
- "cordeump" -> "coredump"
- "of" -> "off" in RPC config comment
- "healty" -> "healthy" in firmware heartbeat comment
- "Firmware crashed detected!" -> "Firmware crash detected!"
- "The could be caused" -> "This could be caused"
- "lockng" -> "locking" in fbnic_time.c
Signed-off-by: Alok Tiwari <alok.a.tiwari@oracle.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20251013160507.768820-1-alok.a.tiwari@oracle.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
drivers/net/wan/hdlc_ppp.c: In function ‘ppp_cp_event’:
drivers/net/wan/hdlc_ppp.c:353:17: warning: ‘%s’ directive argument is null [-Wformat-overflow=]
353 | netdev_info(dev, "%s down\n", proto_name(pid));
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/net/wan/hdlc_ppp.c:342:17: warning: ‘%s’ directive argument is null [-Wformat-overflow=]
342 | netdev_info(dev, "%s up\n", proto_name(pid));
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Update proto_name() to return "LCP" by default instead of NULL.
This change silences the compiler without changing existing behavior
and removes the need for the local 'pname' variable in ppp_cp_event.
Suggested-by: Krzysztof Hałasa <khalasa@piap.pl>
Signed-off-by: Kriish Sharma <kriish.sharma2006@gmail.com>
Acked-by: Krzysztof Hałasa <khalasa@piap.pl>
Link: https://patch.msgid.link/20251013014319.1608706-1-kriish.sharma2006@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Completion napi can free out-of-order tx descriptors if hw QoS is
enabled and packets with different priority are queued to same DMA ring.
Take into account possible out-of-order reports checking if the tx queue
is full using circular buffer head/tail pointer instead of the number of
queued packets.
Fixes: 23020f0493 ("net: airoha: Introduce ethernet support for EN7581 SoC")
Suggested-by: Simon Horman <horms@kernel.org>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20251012-airoha-tx-busy-queue-v2-1-a600b08bab2d@kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
During interface toggle operations (ifdown/ifup), the driver currently
resets the local helper variable 'phy_link' to -1. This causes the link
state machine to incorrectly interpret the state as a link change event,
resulting in spurious "Link is down" messages being logged when the
interface is brought back up.
Preserve the phy_link state across interface toggles to avoid treating
the -1 sentinel value as a legitimate link state transition.
Fixes: 88131a812b ("amd-xgbe: Perform phy connect/disconnect at dev open/stop")
Signed-off-by: Raju Rangoju <Raju.Rangoju@amd.com>
Reviewed-by: Dawid Osuchowski <dawid.osuchowski@linux.intel.com>
Link: https://patch.msgid.link/20251010065142.1189310-1-Raju.Rangoju@amd.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
There was backward compatibility in the terms of mailbox API. Various
drivers from various OSes supporting 10G adapters from Intel portfolio
could easily negotiate mailbox API.
This convention has been broken since introducing API 1.4.
Commit 0062e7cc95 ("ixgbevf: add VF IPsec offload code") added support
for IPSec which is specific only for the kernel ixgbe driver. None of the
rest of the Intel 10G PF/VF drivers supports it. And actually lack of
support was not included in the IPSec implementation - there were no such
code paths. No possibility to negotiate support for the feature was
introduced along with introduction of the feature itself.
Commit 339f289641 ("ixgbevf: Add support for new mailbox communication
between PF and VF") increasing API version to 1.5 did the same - it
introduced code supported specifically by the PF ESX driver. It altered API
version for the VF driver in the same time not touching the version
defined for the PF ixgbe driver. It led to additional discrepancies,
as the code provided within API 1.6 cannot be supported for Linux ixgbe
driver as it causes crashes.
The issue was noticed some time ago and mitigated by Jake within the commit
d0725312ad ("ixgbevf: stop attempting IPSEC offload on Mailbox API 1.5").
As a result we have regression for IPsec support and after increasing API
to version 1.6 ixgbevf driver stopped to support ESX MBX.
To fix this mess add new mailbox op asking PF driver about supported
features. Basing on a response determine whether to set support for IPSec
and ESX-specific enhanced mailbox.
New mailbox op, for compatibility purposes, must be added within new API
revision, as API version of OOT PF & VF drivers is already increased to
1.6 and doesn't incorporate features negotiate op.
Features negotiation mechanism gives possibility to be extended with new
features when needed in the future.
Reported-by: Jacob Keller <jacob.e.keller@intel.com>
Closes: https://lore.kernel.org/intel-wired-lan/20241101-jk-ixgbevf-mailbox-v1-5-fixes-v1-0-f556dc9a66ed@intel.com/
Fixes: 0062e7cc95 ("ixgbevf: add VF IPsec offload code")
Fixes: 339f289641 ("ixgbevf: Add support for new mailbox communication between PF and VF")
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Jedrzej Jagielski <jedrzej.jagielski@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/20251009-jk-iwl-net-2025-10-01-v3-4-ef32a425b92a@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When the driver requests Tx timestamp value, one of the first steps is
to clone SKB using skb_get. It increases the reference counter for that
SKB to prevent unexpected freeing by another component.
However, there may be a case where the index is requested, SKB is
assigned and never consumed by PTP flows - for example due to reset during
running PTP apps.
Add a check in release timestamping function to verify if the SKB
assigned to Tx timestamp latch was freed, and release remaining SKBs.
Fixes: 4901e83a94 ("idpf: add Tx timestamp capabilities negotiation")
Signed-off-by: Milena Olech <milena.olech@intel.com>
Signed-off-by: Anton Nadezhdin <anton.nadezhdin@intel.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Tested-by: Samuel Salin <Samuel.salin@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/20251009-jk-iwl-net-2025-10-01-v3-1-ef32a425b92a@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
After resume from S4 (hibernate), RTL8168H/RTL8111H truncates incoming
packets. Packet captures show messages like "IP truncated-ip - 146 bytes
missing!".
The issue is caused by RxConfig not being properly re-initialized after
resume. Re-initializing the RxConfig register before the chip
re-initialization sequence avoids the truncation and restores correct
packet reception.
This follows the same pattern as commit ef9da46dde ("r8169: fix data
corruption issue on RTL8402").
Fixes: 6e1d0b8988 ("r8169:add support for RTL8168H and RTL8107E")
Signed-off-by: Linmao Li <lilinmao@kylinos.cn>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://patch.msgid.link/20251009122549.3955845-1-lilinmao@kylinos.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There is no error handling for `dma_map_single()` failures.
Add error handling by checking `dma_mapping_error()` and freeing
the `skb` using `dev_kfree_skb()` (process context) when it fails.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Yeounsu Moon <yyyynoom@gmail.com>
Tested-on: D-Link DGE-550T Rev-A3
Suggested-by: Simon Horman <horms@kernel.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Limit tx/rx buffer address to 32-bit address space for board with more
than 4GB DRAM.
Fixes: 804775dfc2 ("net: ethernet: mtk_eth_soc: add support for Wireless Ethernet Dispatch (WED)")
Fixes: 6757d345dd ("net: ethernet: mtk_wed: introduce hw_rro support for MT7988")
Tested-by: Daniel Pawlik <pawlik.dan@gmail.com>
Tested-by: Matteo Croce <teknoraver@meta.com>
Signed-off-by: Rex Lu <rex.lu@mediatek.com>
Co-developed-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function lan78xx_write_raw_eeprom failed to properly propagate EEPROM
write timeout errors (-ETIMEDOUT). In the timeout fallthrough path, it first
attempted to restore the pin configuration for LED outputs and then
returned only the status of that restore operation, discarding the
original timeout error saved in ret.
As a result, callers could mistakenly treat EEPROM write operation as
successful even though the EEPROM write had actually timed out with no
or partial data write.
To fix this, handle errors in restoring the LED pin configuration separately.
If the restore succeeds, return any prior EEPROM write timeout error saved
in ret to the caller.
Suggested-by: Oleksij Rempel <o.rempel@pengutronix.de>
Fixes: 8b1b2ca83b ("net: usb: lan78xx: Improve error handling in EEPROM and OTP operations")
cc: stable@vger.kernel.org
Signed-off-by: Bhanu Seshu Kumar Valluri <bhanuseshukumar@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from Paolo Abeni:
"Including fixes from netfilter.
Current release - regressions:
- mlx5: fix pre-2.40 binutils assembler error
Current release - new code bugs:
- net: psp: don't assume reply skbs will have a socket
- eth: fbnic: fix missing programming of the default descriptor
Previous releases - regressions:
- page_pool: fix PP_MAGIC_MASK to avoid crashing on some 32-bit arches
- tcp:
- take care of zero tp->window_clamp in tcp_set_rcvlowat()
- don't call reqsk_fastopen_remove() in tcp_conn_request()
- eth:
- ice: release xa entry on adapter allocation failure
- usb: asix: hold PM usage ref to avoid PM/MDIO + RTNL deadlock
Previous releases - always broken:
- netfilter: validate objref and objrefmap expressions
- sctp: fix a null dereference in sctp_disposition sctp_sf_do_5_1D_ce()
- eth:
- mlx4: prevent potential use after free in mlx4_en_do_uc_filter()
- mlx5: prevent tunnel mode conflicts between FDB and NIC IPsec tables
- ocelot: fix use-after-free caused by cyclic delayed work
Misc:
- add support for MediaTek PCIe 5G HP DRMR-H01"
* tag 'net-6.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (38 commits)
net: airoha: Fix loopback mode configuration for GDM2 port
selftests: drv-net: pp_alloc_fail: add necessary optoins to config
selftests: drv-net: pp_alloc_fail: lower traffic expectations
selftests: drv-net: fix linter warnings in pp_alloc_fail
eth: fbnic: fix reporting of alloc_failed qstats
selftests: drv-net: xdp: add test for interface level qstats
selftests: drv-net: xdp: rename netnl to ethnl
eth: fbnic: fix saving stats from XDP_TX rings on close
eth: fbnic: fix accounting of XDP packets
eth: fbnic: fix missing programming of the default descriptor
selftests: netfilter: query conntrack state to check for port clash resolution
selftests: netfilter: nft_fib.sh: fix spurious test failures
bridge: br_vlan_fill_forward_path_pvid: use br_vlan_group_rcu()
netfilter: nft_objref: validate objref and objrefmap expressions
net: pse-pd: tps23881: Fix current measurement scaling
net/mlx5: fix pre-2.40 binutils assembler error
net/mlx5e: Do not fail PSP init on missing caps
net/mlx5e: Prevent tunnel reformat when tunnel mode not allowed
net/mlx5: Prevent tunnel mode conflicts between FDB and NIC IPsec tables
net: usb: asix: hold PM usage ref to avoid PM/MDIO + RTNL deadlock
...
Rx processing under normal circumstances has 3 rings - 2 buffer
rings (heads, payloads) and a completion ring. All the rings
have a struct fbnic_ring. Make sure we expose alloc_failed
counter from the buffer rings, previously only the alloc_failed
from the completion ring was reported, even tho all ring types
may increment this counter (buffer rings in __fbnic_fill_bdq()).
This makes the pp_alloc_fail.py test pass, it expects the qstat
to be incrementing as page pool injections happen.
Reviewed-by: Simon Horman <horms@kernel.org>
Fixes: 67dc4eb5fc ("eth: fbnic: report software Rx queue stats")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/20251007232653.2099376-7-kuba@kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
When rings are freed - stats get added to the device level stat
structs. Save the stats from the XDP_TX ring just as Tx stats.
Previously they would be saved to Rx and Tx stats. So we'd not
see XDP_TX packets as Rx during runtime but after an down/up cycle
the packets would appear in stats.
Correct the helper used by ethtool code which does a runtime
config switch.
Reviewed-by: Simon Horman <horms@kernel.org>
Fixes: 5213ff0863 ("eth: fbnic: Collect packet statistics for XDP")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/20251007232653.2099376-4-kuba@kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Make XDP-handled packets appear in the Rx stats. The driver has been
counting XDP_TX packets on the Tx ring, but there wasn't much accounting
on the Rx side (the Rx bytes appear to be incremented on XDP_TX but
XDP_DROP / XDP_ABORT are only counted as Rx drops).
Counting XDP_TX packets (not just bytes) in Rx stats looks like
a simple bug of omission.
The XDP_DROP handling appears to be intentional. Whether XDP_DROP
packets should be counted in interface-level Rx stats is a bit
unclear historically. When we were defining qstats, however,
we clarified based on operational experience that in this context:
name: rx-packets
doc: |
Number of wire packets successfully received and passed to the stack.
For drivers supporting XDP, XDP is considered the first layer
of the stack, so packets consumed by XDP are still counted here.
fbnic does not obey this requirement. Since XDP support has been added
in current release cycle, instead of splitting interface and qstat
handling - make them both follow the qstat definition.
Another small tweak here is that we count bytes as received on the wire
rather than post-XDP bytes (xdp_get_buff_len() vs skb->len).
Reviewed-by: Simon Horman <horms@kernel.org>
Fixes: 5213ff0863 ("eth: fbnic: Collect packet statistics for XDP")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/20251007232653.2099376-3-kuba@kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
XDP_TX typically uses no offloads. To optimize XDP we added a "default
descriptor" feature to the chip, which allows us to send XDP frames with
just the buffer descriptors (DMA address + length). All the metadata
descriptors are derived from the queue config.
Commit under Fixes missed adding setting the defaults up when transplanting
the code from the prototype driver. Importantly after reset the "request
completion" bit is not set. Packets still get sent but there's no
completion, so ring is not cleaned up. We can send one ring's worth
of packets and then will start dropping all frames that got the XDP_TX
action from the XDP prog.
Reviewed-by: Simon Horman <horms@kernel.org>
Fixes: 168deb7b31 ("eth: fbnic: Add support for XDP_TX action")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/20251007232653.2099376-2-kuba@kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
