Currently, during the LAN8814 PTP probe shared->phydev is only set if PTP
clock gets actually set, otherwise the function will return before setting
it.
This is an issue as shared->phydev is unconditionally being used when IRQ
is being handled, especially in lan8814_gpio_process_cap and since it was
not set it will cause a NULL pointer exception and crash the kernel.
So, simply always set shared->phydev to avoid the NULL pointer exception.
Fixes: b3f1a08fcf ("net: phy: micrel: Add support for PTP_PF_EXTTS for lan8814")
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Tested-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Link: https://patch.msgid.link/20251021132034.983936-1-robert.marko@sartura.hr
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In ath11k_wmi_send_peer_assoc_cmd(), peer's transmit MCS is sent to
firmware as receive MCS while peer's receive MCS sent as transmit MCS,
which goes against firmwire's definition.
While connecting to a misbehaved AP that advertises 0xffff (meaning not
supported) for 160 MHz transmit MCS map, firmware crashes due to 0xffff
is assigned to he_mcs->rx_mcs_set field.
Ext Tag: HE Capabilities
[...]
Supported HE-MCS and NSS Set
[...]
Rx and Tx MCS Maps 160 MHz
[...]
Tx HE-MCS Map 160 MHz: 0xffff
Swap the assignment to fix this issue.
As the HE rate control mask is meant to limit our own transmit MCS, it
needs to go via he_mcs->rx_mcs_set field. With the aforementioned swapping
done, change is needed as well to apply it to the peer's receive MCS.
Tested-on: WCN6855 hw2.1 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.41
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Fixes: 61fe43e721 ("ath11k: add support for setting fixed HE rate/gi/ltf")
Signed-off-by: Baochen Qiang <baochen.qiang@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20251017-ath11k-mcs-assignment-v1-2-da40825c1783@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
While associating, firmware needs to know peer's receive capability to
calculate its own VHT transmit MCS, currently host sends this information
to firmware via mcs->rx_mcs_set field, this is wrong as firmware actually
takes it from mcs->tx_mcs_set field. Till now there is no failure seen
due to this, most likely because almost all peers are advertising the
same capability for both transmit and receive. Swap the assignment to
fix it.
Besides, rate control mask is meant to limit our own transmit MCS, hence
need to go via mcs->tx_mcs_set field. With the aforementioned swapping
done, change is needed as well to apply it to the peer's receive
capability rather than transmit capability.
Tested-on: WCN6855 hw2.1 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.41
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Fixes: d5c65159f2 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Signed-off-by: Baochen Qiang <baochen.qiang@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20251017-ath11k-mcs-assignment-v1-1-da40825c1783@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
openvpn TCP encapsulation uses a custom queue to deliver packets to
userspace. Currently it relies on datagram_poll, which checks
sk_receive_queue, leading to false readiness signals when that queue
contains non-userspace packets.
Switch ovpn_tcp_poll to use datagram_poll_queue with the peer's
user_queue, ensuring poll only signals readiness when userspace data is
actually available. Also refactor ovpn_tcp_poll in order to enforce the
assumption we can make on the lifetime of ovpn_sock and peer.
Fixes: 11851cbd60 ("ovpn: implement TCP transport")
Signed-off-by: Antonio Quartulli <antonio@openvpn.net>
Signed-off-by: Ralf Lici <ralf@mandelbit.com>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Link: https://patch.msgid.link/20251021100942.195010-4-ralf@mandelbit.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
If the send_peer_notif counter and the peer event notify are not synchronized.
It may cause problems such as the loss or dup of peer notify event.
Before this patch:
- If should_notify_peers is true and the lock for send_peer_notif-- fails, peer
event may be sent again in next mii_monitor loop, because should_notify_peers
is still true.
- If should_notify_peers is true and the lock for send_peer_notif-- succeeded,
but the lock for peer event fails, the peer event will be lost.
This patch locks the RTNL for send_peer_notif, events, and commit simultaneously.
Fixes: 07a4ddec3c ("bonding: add an option to specify a delay between peer notifications")
Cc: Jay Vosburgh <jv@jvosburgh.net>
Cc: Andrew Lunn <andrew+netdev@lunn.ch>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: Hangbin Liu <liuhangbin@gmail.com>
Cc: Nikolay Aleksandrov <razor@blackwall.org>
Cc: Vincent Bernat <vincent@bernat.ch>
Cc: <stable@vger.kernel.org>
Signed-off-by: Tonghao Zhang <tonghao@bamaicloud.com>
Acked-by: Jay Vosburgh <jv@jvosburgh.net>
Link: https://patch.msgid.link/20251021050933.46412-1-tonghao@bamaicloud.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
An error code was assigned to a variable and checked accordingly.
This value was passed to a dev_err_probe() call in an if branch.
This function is documented in the way that the same value is returned.
Thus delete two redundant variable reassignments.
The source code was transformed by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Link: https://patch.msgid.link/71f7daa3-d4f4-4753-aae8-67040fc8297d@web.de
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The TLV_MAX_DATA macro calculates (PAGE_SIZE - 512) which can exceed
the maximum value of a 16-bit unsigned integer on architectures with
large page sizes, causing compiler warnings:
drivers/net/ethernet/meta/fbnic/fbnic_tlv.h:83:24: warning: conversion
from 'long unsigned int' to 'short unsigned int' changes value from
'261632' to '65024' [-Woverflow]
Fix this by explicitly masking the result to 16 bits using bitwise AND
with 0xFFFF, ensuring the value fits within the expected data type
while maintaining the intended behavior for normal page sizes.
This preserves the existing functionality while eliminating the
compiler warning and potential undefined behavior from integer
truncation.
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202510190832.3SQkTCHe-lkp@intel.com/
Signed-off-by: Pei Xiao <xiaopei01@kylinos.cn>
Link: https://patch.msgid.link/182b9d0235d044d69d7a57c1296cc6f46e395beb.1761039651.git.xiaopei01@kylinos.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-Wflex-array-member-not-at-end was introduced in GCC-14, and we are
getting ready to enable it, globally.
Use regular arrays instead of flexible-array members (they're not
really needed in this case) in a couple of unions, and fix the
following warnings:
1 drivers/net/ethernet/spacemit/k1_emac.c:122:42: warning: structure containing a flexible array member is not at the end of another structure [-Wflex-array-member-not-at-end]
1 drivers/net/ethernet/spacemit/k1_emac.c:122:32: warning: structure containing a flexible array member is not at the end of another structure [-Wflex-array-member-not-at-end]
1 drivers/net/ethernet/spacemit/k1_emac.c:121:42: warning: structure containing a flexible array member is not at the end of another structure [-Wflex-array-member-not-at-end]
1 drivers/net/ethernet/spacemit/k1_emac.c:121:32: warning: structure containing a flexible array member is not at the end of another structure [-Wflex-array-member-not-at-end]
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Acked-by: Vivian Wang <wangruikang@iscas.ac.cn>
Link: https://patch.msgid.link/aPd0YjO-oP60Lgvj@kspp
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Ensure the TX descriptor type fields are published in a safe order so the
DMA engine never begins processing a descriptor chain before all descriptor
fields are fully initialised.
For multi-descriptor transmits the driver writes DT_FEND into the last
descriptor and DT_FSTART into the first. The DMA engine begins processing
when it observes DT_FSTART. Move the dma_wmb() barrier so it executes
immediately after DT_FEND and immediately before writing DT_FSTART
(and before DT_FSINGLE in the single-descriptor case). This guarantees
that all prior CPU writes to the descriptor memory are visible to the
device before DT_FSTART is seen.
This avoids a situation where compiler/CPU reordering could publish
DT_FSTART ahead of DT_FEND or other descriptor fields, allowing the DMA to
start on a partially initialised chain and causing corrupted transmissions
or TX timeouts. Such a failure was observed on RZ/G2L with an RT kernel as
transmit queue timeouts and device resets.
Fixes: 2f45d1902a ("ravb: minimize TX data copying")
Cc: stable@vger.kernel.org
Co-developed-by: Fabrizio Castro <fabrizio.castro.jz@renesas.com>
Signed-off-by: Fabrizio Castro <fabrizio.castro.jz@renesas.com>
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://patch.msgid.link/20251017151830.171062-4-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Existing tools like myftm use 'legacy' test command API. Similarly
to ath11k and ath12k, we want to support raw TLV payload submitted
from the test tool. This requires segmenting the TLV payload and
encapsulating it within a WMI command. The opposite operation needs
to be done upon corresponding event receiving.
Tested-on: WCN3990 hw1.0 WLAN.HL.3.3.7.c2-00931-QCAHLSWMTPLZ-1
Signed-off-by: Loic Poulain <loic.poulain@oss.qualcomm.com>
Link: https://patch.msgid.link/20251020153759.407516-1-loic.poulain@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Replace `dev_kfree_skb()` with `dev_kfree_skb_any()` in `start_xmit()`
which can be called from netpoll (hard IRQ) and from other contexts.
Also, `np->link_status` can be changed at any time by interrupt handler.
<idle>-0 [011] dNh4. 4541.754603: start_xmit <-netpoll_start_xmit
<idle>-0 [011] dNh4. 4541.754622: <stack trace>
=> [FTRACE TRAMPOLINE]
=> start_xmit
=> netpoll_start_xmit
=> netpoll_send_skb
=> write_msg
=> console_flush_all
=> console_unlock
=> vprintk_emit
=> _printk
=> rio_interrupt
=> __handle_irq_event_percpu
=> handle_irq_event
=> handle_fasteoi_irq
=> __common_interrupt
=> common_interrupt
=> asm_common_interrupt
=> mwait_idle
=> default_idle_call
=> do_idle
=> cpu_startup_entry
=> start_secondary
=> common_startup_64
This issue can occur when the link state changes from off to on
(e.g., plugging or unplugging the LAN cable) while transmitting a
packet. If the skb has a destructor, a warning message may be
printed in this situation.
-> consume_skb (dev_kfree_skb())
-> __kfree_skb()
-> skb_release_all()
-> skb_release_head_state(skb)
if (skb->destructor) {
DEBUG_NET_WARN_ON_ONCE(in_hardirq());
skb->destructor(skb);
}
Found by inspection.
Signed-off-by: Yeounsu Moon <yyyynoom@gmail.com>
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Tested-on: D-Link DGE-550T Rev-A3
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20251019075540.55697-1-yyyynoom@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
update old legacy cleanup_module from the file with __exit
module as per kernel code practices and restore the #ifdef
MODULE condition to allow successful compilation as a built
-in driver.
The file had an old cleanup_module still in use which could
be updated with __exit module function although its init_module
is indeed newer however the cleanup_module was still
using the older version of exit.
To set proper exit module function replace cleanup_module
with __exit corkscrew_exit_module to align it to the
kernel code consistency.
Signed-off-by: Shi Hao <i.shihao.999@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20251018052541.124365-1-i.shihao.999@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Motorcomm YT921x is a series of ethernet switches developed by Shanghai
Motorcomm Electronic Technology, including:
- YT9215S / YT9215RB / YT9215SC: 5 GbE PHYs
- YT9213NB / YT9214NB: 2 GbE PHYs
- YT9218N / YT9218MB: 8 GbE PHYs
and up to 2 GMACs.
Driver verified on a stock wireless router with IPQ5018 + YT9215S.
Signed-off-by: David Yang <mmyangfl@gmail.com>
Link: https://patch.msgid.link/20251017060859.326450-4-mmyangfl@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use the new helper netdev_compute_master_upper_features() to compute the
team device features. This helper performs both the feature computation
and the netdev_change_features() call.
Note that such change replace the lower layer traversing currently done
using team->port_list with netdev_for_each_lower_dev(). Such change is
safe as `port_list` contains exactly the same elements as
`team->dev->adj_list.lower` and the helper is always invoked under the
RTNL lock.
With this change, the explicit netdev_change_features() in team_add_slave()
can be safely removed, as team_port_add() already takes care of the
notification via netdev_compute_master_upper_features(), and same thing for
team_del_slave()
This also fixes missing computations for MPLS, XFRM, and TSO/GSO partial
features.
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Link: https://patch.msgid.link/20251017034155.61990-4-liuhangbin@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use the new functon netdev_compute_master_upper_features() to compute the bonding
features.
Note that bond_compute_features() currently uses bond_for_each_slave()
to traverse the lower devices list, and that is just a macro wrapper of
netdev_for_each_lower_private(). We use similar helper
netdev_for_each_lower_dev() in netdev_compute_master_upper_features() to
iterate the slave device, as there is not need to get the private data.
No functional change intended.
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Link: https://patch.msgid.link/20251017034155.61990-3-liuhangbin@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Marc Kleine-Budde says:
====================
pull-request: can 2025-10-20
All patches are by me. The first 3 update the bxcan, esd and rockchip
driver to drop skbs in xmit of the device is in listen only mode.
The last patch targets the CAN netlink implementation to allow the
disabling of automatic restart after Bus-Off, even if the a driver
doesn't implement that callback.
* tag 'linux-can-fixes-for-6.18-20251020' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can:
can: netlink: can_changelink(): allow disabling of automatic restart
can: rockchip-canfd: rkcanfd_start_xmit(): use can_dev_dropped_skb() instead of can_dropped_invalid_skb()
can: esd: acc_start_xmit(): use can_dev_dropped_skb() instead of can_dropped_invalid_skb()
can: bxcan: bxcan_start_xmit(): use can_dev_dropped_skb() instead of can_dropped_invalid_skb()
====================
Link: https://patch.msgid.link/20251020152516.1590553-1-mkl@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Select the PPE default cpu port in airoha_dev_init routine.
This patch allows to distribute the load between the two available cpu
ports (FE_PSE_PORT_CDM1 and FE_PSE_PORT_CDM2) if the device is running a
single PPE module (e.g. 7583) selecting the cpu port based on the use
QDMA device. For multi-PPE device (e.g. 7581) assign FE_PSE_PORT_CDM1 to
PPE1 and FE_PSE_PORT_CDM2 to PPE2.
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://patch.msgid.link/20251017-an7583-eth-support-v3-10-f28319666667@kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Introduce airoha_ppe_get_num_stats_entries and
airoha_ppe_get_num_total_stats_entries routines in order to make the
code more readable controlling if CONFIG_NET_AIROHA_FLOW_STATS is
enabled or disabled.
Modify airoha_ppe_foe_get_flow_stats_index routine signature relying on
airoha_ppe_get_num_total_stats_entries().
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://patch.msgid.link/20251017-an7583-eth-support-v3-3-f28319666667@kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Resolve race conditions in timestamp events list handling between TX
and RX paths causing missed timestamps.
The current implementation uses a single events list for both TX and RX
timestamps. The am65_cpts_find_ts() function acquires the lock,
splices all events (TX as well as RX events) to a temporary list,
and releases the lock. This function performs matching of timestamps
for TX packets only. Before it acquires the lock again to put the
non-TX events back to the main events list, a concurrent RX
processing thread could acquire the lock (as observed in practice),
find an empty events list, and fail to attach timestamp to it,
even though a relevant event exists in the spliced list which is yet to
be restored to the main list.
Fix this by creating separate events lists to handle TX and RX
timestamps independently.
Fixes: c459f606f6 ("net: ethernet: ti: am65-cpts: Enable RX HW timestamp for PTP packets using CPTS FIFO")
Signed-off-by: Aksh Garg <a-garg7@ti.com>
Reviewed-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Link: https://patch.msgid.link/20251016115755.1123646-1-a-garg7@ti.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Marc Kleine-Budde says:
====================
pull-request: can-next 2025-10-17
The first patch is by me and adds support for an optional reset to the
m_can drivers.
Vincent Mailhol's patch targets all drivers and removes the
can_change_mtu() function, since the netdev's min and max MTU are
populated.
Markus Schneider-Pargmann contributes 4 patches to the m_can driver to
add am62 wakeup support.
The last 7 patches are by me and provide various cleanups to the m_can
driver.
* tag 'linux-can-next-for-6.19-20251017' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next:
can: m_can: m_can_get_berr_counter(): don't wake up controller if interface is down
can: m_can: m_can_tx_submit(): remove unneeded sanity checks
can: m_can: m_can_class_register(): remove error message in case devm_kzalloc() fails
can: m_can: m_can_interrupt_enable(): use m_can_write() instead of open coding it
net: m_can: convert dev_{dbg,info,err} -> netdev_{dbg,info,err}
can: m_can: hrtimer_callback(): rename to m_can_polling_timer()
can: m_can: m_can_init_ram(): make static
can: m_can: Support pinctrl wakeup state
can: m_can: Return ERR_PTR on error in allocation
can: m_can: Map WoL to device_set_wakeup_enable
dt-bindings: can: m_can: Add wakeup properties
can: treewide: remove can_change_mtu()
can: m_can: add support for optional reset
====================
Link: https://patch.msgid.link/20251017150819.1415685-1-mkl@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Refactor the ethtool ring parameter configuration logic to address two
issues: unnecessary queue resets and lost configuration changes when
the interface is down.
Previously, `gve_set_ringparam` could trigger multiple queue
destructions and recreations for a single command, as different settings
(e.g., header split, ring sizes) were applied one by one. Furthermore,
if the interface was down, any changes made via ethtool were discarded
instead of being saved for the next time the interface was brought up.
This patch centralizes the configuration logic. Individual functions
like `gve_set_hsplit_config` are modified to only validate and stage
changes in a temporary config struct.
The main `gve_set_ringparam` function now gathers all staged changes
and applies them as a single, combined configuration:
1. If the interface is up, it calls `gve_adjust_config` once.
2. If the interface is down, it saves the settings directly to the
driver's private struct, ensuring they persist and are used when
the interface is brought back up.
Signed-off-by: Ankit Garg <nktgrg@google.com>
Reviewed-by: Harshitha Ramamurthy <hramamurthy@google.com>
Reviewed-by: Jordan Rhee <jordanrhee@google.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Joshua Washington <joshwash@google.com>
Link: https://patch.msgid.link/20251017012614.3631351-1-joshwash@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
XDP programs can change the layout of an xdp_buff through
bpf_xdp_adjust_tail() and bpf_xdp_adjust_head(). Therefore, the driver
cannot assume the size of the linear data area nor fragments. Fix the
bug in mlx5 by generating skb according to xdp_buff after XDP programs
run.
Currently, when handling multi-buf XDP, the mlx5 driver assumes the
layout of an xdp_buff to be unchanged. That is, the linear data area
continues to be empty and fragments remain the same. This may cause
the driver to generate erroneous skb or triggering a kernel
warning. When an XDP program added linear data through
bpf_xdp_adjust_head(), the linear data will be ignored as
mlx5e_build_linear_skb() builds an skb without linear data and then
pull data from fragments to fill the linear data area. When an XDP
program has shrunk the non-linear data through bpf_xdp_adjust_tail(),
the delta passed to __pskb_pull_tail() may exceed the actual nonlinear
data size and trigger the BUG_ON in it.
To fix the issue, first record the original number of fragments. If the
number of fragments changes after the XDP program runs, rewind the end
fragment pointer by the difference and recalculate the truesize. Then,
build the skb with the linear data area matching the xdp_buff. Finally,
only pull data in if there is non-linear data and fill the linear part
up to 256 bytes.
Fixes: f52ac7028b ("net/mlx5e: RX, Add XDP multi-buffer support in Striding RQ")
Signed-off-by: Amery Hung <ameryhung@gmail.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/1760644540-899148-3-git-send-email-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
XDP programs can release xdp_buff fragments when calling
bpf_xdp_adjust_tail(). The driver currently assumes the number of
fragments to be unchanged and may generate skb with wrong truesize or
containing invalid frags. Fix the bug by generating skb according to
xdp_buff after the XDP program runs.
Fixes: ea5d49bdae ("net/mlx5e: Add XDP multi buffer support to the non-linear legacy RQ")
Reviewed-by: Dragos Tatulea <dtatulea@nvidia.com>
Signed-off-by: Amery Hung <ameryhung@gmail.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/1760644540-899148-2-git-send-email-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
