When runtime PM is used for clock providers that are part of a power
domain, the power domain supply is cut off during runtime suspend. This
causes all BLK CTL registers belonging to that power domain to reset. To
prevent this, save the state of the registers before entering suspend
and restore them on resume. Additionally, disable the APB clock during
suspend to minimize power consumption.
Signed-off-by: Laurentiu Palcu <laurentiu.palcu@oss.nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20250804131450.3918846-3-laurentiu.palcu@oss.nxp.com
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
* clk-pm:
clk: qcom: Remove redundant pm_runtime_mark_last_busy() calls
clk: imx: Remove redundant pm_runtime_mark_last_busy() calls
Documentation: PM: *_autosuspend() functions update last busy time
PM: runtime: Mark last busy stamp in pm_request_autosuspend()
PM: runtime: Mark last busy stamp in pm_runtime_autosuspend()
PM: runtime: Mark last busy stamp in pm_runtime_put_sync_autosuspend()
PM: runtime: Mark last busy stamp in pm_runtime_put_autosuspend()
PM: runtime: Document return values of suspend-related API functions
The round_rate() clk ops is deprecated, so migrate this driver from
round_rate() to determine_rate() using the Coccinelle semantic patch
on the cover letter of this series.
This driver also implements both the determine_rate() and round_rate()
clk ops, and the round_rate() clk ops is deprecated. When both are
defined, clk_core_determine_round_nolock() from the clk core will only
use the determine_rate() clk ops, so let's remove the round_rate() clk
ops since it's unused.
Signed-off-by: Brian Masney <bmasney@redhat.com>
Link: https://lore.kernel.org/r/20250710-clk-imx-round-rate-v1-13-5726f98e6d8d@redhat.com
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
When enabling runtime PM for clock suppliers that also belong to a power
domain, the following crash is thrown:
error: synchronous external abort: 0000000096000010 [#1] PREEMPT SMP
Workqueue: events_unbound deferred_probe_work_func
pstate: 60400009 (nZCv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--)
pc : clk_mux_get_parent+0x60/0x90
lr : clk_core_reparent_orphans_nolock+0x58/0xd8
Call trace:
clk_mux_get_parent+0x60/0x90
clk_core_reparent_orphans_nolock+0x58/0xd8
of_clk_add_hw_provider.part.0+0x90/0x100
of_clk_add_hw_provider+0x1c/0x38
imx95_bc_probe+0x2e0/0x3f0
platform_probe+0x70/0xd8
Enabling runtime PM without explicitly resuming the device caused
the power domain cut off after clk_register() is called. As a result,
a crash happens when the clock hardware provider is added and attempts
to access the BLK_CTL register.
Fix this by using devm_pm_runtime_enable() instead of pm_runtime_enable()
and getting rid of the pm_runtime_disable() in the cleanup path.
Fixes: 5224b18946 ("clk: imx: add i.MX95 BLK CTL clk driver")
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Signed-off-by: Laurentiu Palcu <laurentiu.palcu@oss.nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Link: https://lore.kernel.org/r/20250707-imx95-blk-ctl-7-1-v3-2-c1b676ec13be@nxp.com
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
The IMX8MPCEC datasheet lists maximum frequencies allowed for different
modules. Some of these limits are universal, but some depend on
whether the SoC is operating in nominal or in overdrive mode.
The imx8mp.dtsi currently assumes overdrive mode and configures some
clocks in accordance with this. Boards wishing to make use of nominal
mode will need to override some of the clock rates manually.
As operating the clocks outside of their allowed range can lead to
difficult to debug issues, it makes sense to register the maximum rates
allowed in the driver, so the CCF can take them into account.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Link: https://lore.kernel.org/r/20250218-imx8m-clk-v4-6-b7697dc2dcd0@pengutronix.de
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
* clk-fixes:
clk: clk-loongson2: Fix the number count of clk provider
clk: mmp2: call pm_genpd_init() only after genpd.name is set
clk: sunxi-ng: a100: enable MMC clock reparenting
clk: clk-imx8mp-audiomix: fix function signature
clk: thead: Fix TH1520 emmc and shdci clock rate
The CLKOUTn may be fed from PLL1/2/3, but the PLL1/2/3 has to be enabled
first by setting PLL_CLKE bit 11 in CCM_ANALOG_SYS_PLLn_GEN_CTRL register.
The CCM_ANALOG_SYS_PLLn_GEN_CTRL bit 11 is modeled by plln_out clock. Fix
the clock tree and place the clkout1/2 under plln_sel instead of plain plln
to let the clock subsystem correctly control the bit 11 and enable the PLL
in case the CLKOUTn is supplied by PLL1/2/3.
Fixes: 43896f56b5 ("clk: imx8mp: add clkout1/2 support")
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Link: https://lore.kernel.org/r/20241112013718.333771-1-marex@denx.de
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
On i.MX8QM, HDMI LPCG clocks operation needs SCU clock "hdmi_ipg_clk"
to be ON. While during noirq suspend phase, "hdmi_ipg_clk" is disabled
by HDMI IRQ STEER driver, so SError will be triggered when accessing
the HDMI LPCG registers.
Skip all HDMI LPCG clocks save/restore to avoid SError during
system suspend/resume, it will NOT introduce additional power consumption
as their parent clock is disabled when suspend.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Link: https://lore.kernel.org/r/20241027-imx-clk-v1-v3-5-89152574d1d7@nxp.com
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
The scu clk_ops only inplements prepare() and unprepare() callback.
Saving the clock state during suspend by checking clk_hw_is_enabled()
is not safe as it's possible that some device drivers may only
disable the clocks without unprepare. Then the state retention will not
work for such clocks.
Fixing it by checking clk_hw_is_prepared() which is more reasonable
and safe.
Fixes: d0409631f4 ("clk: imx: scu: add suspend/resume support")
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Tested-by: Carlos Song <carlos.song@nxp.com>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Link: https://lore.kernel.org/r/20241027-imx-clk-v1-v3-4-89152574d1d7@nxp.com
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
To i.MX93 which features dual Cortex-A55 cores and DSU, when using
writel_relaxed to write value to PLL registers, the value might be
buffered. To make sure the value has been written into the hardware,
using readl to read back the register could achieve the goal.
current PLL power up flow can be simplified as below:
1. writel_relaxed to set the PLL POWERUP bit;
2. readl_poll_timeout to check the PLL lock bit:
a). timeout = ktime_add_us(ktime_get(), timeout_us);
b). readl the pll the lock reg;
c). check if the pll lock bit ready
d). check if timeout
But in some corner cases, both the write in step 1 and read in
step 2 will be blocked by other bus transaction in the SoC for a
long time, saying the value into real hardware is just before step b).
That means the timeout counting has begins for quite sometime since
step a), but value still not written into real hardware until bus
released just at a point before step b).
Then there maybe chances that the pll lock bit is not ready
when readl done but the timeout happens. readl_poll_timeout will
err return due to timeout. To avoid such unexpected failure,
read back the reg to make sure the write has been done in HW
reg.
So use readl after writel_relaxed to fix the issue.
Since we are here, to avoid udelay to run before writel_relaxed, use
readl before udelay.
Fixes: 1b26cb8a77 ("clk: imx: support fracn gppll")
Co-developed-by: Jacky Bai <ping.bai@nxp.com>
Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/20241027-imx-clk-v1-v3-3-89152574d1d7@nxp.com
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Per i.MX93 Reference Mannual 22.4 Initialization information
1. Program appropriate value of DIV[ODIV], DIV[RDIV] and DIV[MFI]
as per Integer mode.
2. Wait for 5 μs.
3. Program the following field in CTRL register.
Set CTRL[POWERUP] to 1'b1 to enable PLL block.
4. Poll PLL_STATUS[PLL_LOCK] register, and wait till PLL_STATUS[PLL_LOCK]
is 1'b1 and pll_lock output signal is 1'b1.
5. Set CTRL[CLKMUX_EN] to 1'b1 to enable PLL output clock.
So move the CLKMUX_EN operation after PLL locked.
Fixes: 1b26cb8a77 ("clk: imx: support fracn gppll")
Co-developed-by: Jacky Bai <ping.bai@nxp.com>
Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/20241027-imx-clk-v1-v3-2-89152574d1d7@nxp.com
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Reuse i.MX93 clk driver for i.MX91, because i.MX91 reuses the
Clock Control Module from i.MX93, with only a few clocks removed
and a few clocks added.
For clocks specific to i.MX93 use PLAT_IMX93 to flag them, for
clocks specific to i.MX91, use PLAT_IMX91 to flag them. Others
are shared by both.
Signed-off-by: Pengfei Li <pengfei.li_1@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Link: https://lore.kernel.org/r/20241023184651.381265-5-pengfei.li_1@nxp.com
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
IMX93_CLK_END was previously defined in imx93-clock.h to indicate
the number of clocks. However, it is not part of the ABI. For starters
it does no really appear in DTS. But what's more important - new clocks
are described later, which contradicts this define in binding header.
So move this macro to clock driver.
Signed-off-by: Pengfei Li <pengfei.li_1@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/20241023184651.381265-2-pengfei.li_1@nxp.com
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
After commit 0edb555a65 ("platform: Make platform_driver::remove()
return void") .remove() is (again) the right callback to implement for
platform drivers.
Convert all clk drivers to use .remove(), with the eventual goal to drop
struct platform_driver::remove_new(). As .remove() and .remove_new() have
the same prototypes, conversion is done by just changing the structure
member name in the driver initializer.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Link: https://lore.kernel.org/r/20240909144026.870565-2-u.kleine-koenig@baylibre.com
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be> # renesas
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The media_disp[12]_pix clock supply LCDIFv3 pixel clock output. These
clocks are usually the only downstream clock from Video PLL on i.MX8MP.
Allow these clocks to reconfigure the Video PLL, as that results in
accurate pixel clock. If the Video PLL is not reconfigured, the pixel
clock accuracy is low.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/20240531202648.277078-1-marex@denx.de
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
The initialization order of SCU clocks affects the sequence of SCU clock
resume. If there are no other effects, the earlier the initialization,
the earlier the resume. During SCU clock resume, the clock rate is
restored. As SCFW guidelines, configure the parent clock rate before
configuring the child rate.
Fixes: babfaa9556 ("clk: imx: scu: add more scu clocks")
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/20240607133347.3291040-15-peng.fan@oss.nxp.com
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
