Pull networking fixes from David Miller:
1) Fix non-blocking connect() in x25, from Martin Schiller.
2) Fix spurious decryption errors in kTLS, from Jakub Kicinski.
3) Netfilter use-after-free in mtype_destroy(), from Cong Wang.
4) Limit size of TSO packets properly in lan78xx driver, from Eric
Dumazet.
5) r8152 probe needs an endpoint sanity check, from Johan Hovold.
6) Prevent looping in tcp_bpf_unhash() during sockmap/tls free, from
John Fastabend.
7) hns3 needs short frames padded on transmit, from Yunsheng Lin.
8) Fix netfilter ICMP header corruption, from Eyal Birger.
9) Fix soft lockup when low on memory in hns3, from Yonglong Liu.
10) Fix NTUPLE firmware command failures in bnxt_en, from Michael Chan.
11) Fix memory leak in act_ctinfo, from Eric Dumazet.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (91 commits)
cxgb4: reject overlapped queues in TC-MQPRIO offload
cxgb4: fix Tx multi channel port rate limit
net: sched: act_ctinfo: fix memory leak
bnxt_en: Do not treat DSN (Digital Serial Number) read failure as fatal.
bnxt_en: Fix ipv6 RFS filter matching logic.
bnxt_en: Fix NTUPLE firmware command failures.
net: systemport: Fixed queue mapping in internal ring map
net: dsa: bcm_sf2: Configure IMP port for 2Gb/sec
net: dsa: sja1105: Don't error out on disabled ports with no phy-mode
net: phy: dp83867: Set FORCE_LINK_GOOD to default after reset
net: hns: fix soft lockup when there is not enough memory
net: avoid updating qdisc_xmit_lock_key in netdev_update_lockdep_key()
net/sched: act_ife: initalize ife->metalist earlier
netfilter: nat: fix ICMP header corruption on ICMP errors
net: wan: lapbether.c: Use built-in RCU list checking
netfilter: nf_tables: fix flowtable list del corruption
netfilter: nf_tables: fix memory leak in nf_tables_parse_netdev_hooks()
netfilter: nf_tables: remove WARN and add NLA_STRING upper limits
netfilter: nft_tunnel: ERSPAN_VERSION must not be null
netfilter: nft_tunnel: fix null-attribute check
...
Pull drm fixes from Dave Airlie:
"Back from LCA2020, fixes wasn't too busy last week, seems to have
quieten down appropriately, some amdgpu, i915, then a core mst fix and
one fix for virtio-gpu and one for rockchip:
core mst:
- serialize down messages and clear timeslots are on unplug
amdgpu:
- Update golden settings for renoir
- eDP fix
i915:
- uAPI fix: Remove dash and colon from PMU names to comply with
tools/perf
- Fix for include file that was indirectly included
- Two fixes to make sure VMA are marked active for error capture
virtio:
- maintain obj reservation lock when submitting cmds
rockchip:
- increase link rate var size to accommodate rates"
* tag 'drm-fixes-2020-01-19' of git://anongit.freedesktop.org/drm/drm:
drm/amd/display: Reorder detect_edp_sink_caps before link settings read.
drm/amdgpu: update goldensetting for renoir
drm/dp_mst: Have DP_Tx send one msg at a time
drm/dp_mst: clear time slots for ports invalid
drm/i915/pmu: Do not use colons or dashes in PMU names
drm/rockchip: fix integer type used for storing dp data rate
drm/i915/gt: Mark ring->vma as active while pinned
drm/i915/gt: Mark context->state vma as active while pinned
drm/i915/gt: Skip trying to unbind in restore_ggtt_mappings
drm/i915: Add missing include file <linux/math64.h>
drm/virtio: add missing virtio_gpu_array_lock_resv call
Pull rseq fixes from Ingo Molnar:
"Two rseq bugfixes:
- CLONE_VM !CLONE_THREAD didn't work properly, the kernel would end
up corrupting the TLS of the parent. Technically a change in the
ABI but the previous behavior couldn't resonably have been relied
on by applications so this looks like a valid exception to the ABI
rule.
- Make the RSEQ_FLAG_UNREGISTER ABI behavior consistent with the
handling of other flags. This is not thought to impact any
applications either"
* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
rseq: Unregister rseq for clone CLONE_VM
rseq: Reject unknown flags on rseq unregister
Pull block fixes from Jens Axboe:
"Three fixes that should go into this release:
- The 32-bit segment size fix that I mentioned last week (Ming)
- Use uint for the block size (Mikulas)
- A null_blk zone write handling fix (Damien)"
* tag 'block-5.5-2020-01-16' of git://git.kernel.dk/linux-block:
block: fix an integer overflow in logical block size
null_blk: Fix zone write handling
block: fix get_max_segment_size() overflow on 32bit arch
Pull ARM SoC fixes from Olof Johansson:
"I've been sitting on these longer than I meant, so the patch count is
a bit higher than ideal for this part of the release. There's also
some reverts of double-applied patches that brings the diffstat up a
bit.
With that said, the biggest changes are:
- Revert of duplicate i2c device addition on two Aspeed (BMC)
Devicetrees.
- Move of two device nodes that got applied to the wrong part of the
tree on ASpeed G6.
- Regulator fix for Beaglebone X15 (adding 12/5V supplies)
- Use interrupts for keys on Amlogic SM1 to avoid missed polls
In addition to that, there is a collection of smaller DT fixes:
- Power supply assignment fixes for i.MX6
- Fix of interrupt line for magnetometer on i.MX8 Librem5 devkit
- Build fixlets (selects) for davinci/omap2+
- More interrupt number fixes for Stratix10, Amlogic SM1, etc.
- ... and more similar fixes across different platforms
And some non-DT stuff:
- optee fix to register multiple shared pages properly
- Clock calculation fixes for MMP3
- Clock fixes for OMAP as well"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (42 commits)
MAINTAINERS: Add myself as the co-maintainer for Actions Semi platforms
ARM: dts: imx7: Fix Toradex Colibri iMX7S 256MB NAND flash support
ARM: dts: imx6sll-evk: Remove incorrect power supply assignment
ARM: dts: imx6sl-evk: Remove incorrect power supply assignment
ARM: dts: imx6sx-sdb: Remove incorrect power supply assignment
ARM: dts: imx6qdl-sabresd: Remove incorrect power supply assignment
ARM: dts: imx6q-icore-mipi: Use 1.5 version of i.Core MX6DL
ARM: omap2plus: select RESET_CONTROLLER
ARM: davinci: select CONFIG_RESET_CONTROLLER
ARM: dts: aspeed: rainier: Fix fan fault and presence
ARM: dts: aspeed: rainier: Remove duplicate i2c busses
ARM: dts: aspeed: tacoma: Remove duplicate flash nodes
ARM: dts: aspeed: tacoma: Remove duplicate i2c busses
ARM: dts: aspeed: tacoma: Fix fsi master node
ARM: dts: aspeed-g6: Fix FSI master location
ARM: dts: mmp3: Fix the TWSI ranges
clk: mmp2: Fix the order of timer mux parents
ARM: mmp: do not divide the clock rate
arm64: dts: rockchip: Fix IR on Beelink A1
optee: Fix multi page dynamic shm pool alloc
...
Daniel Borkmann says:
====================
pull-request: bpf 2020-01-15
The following pull-request contains BPF updates for your *net* tree.
We've added 12 non-merge commits during the last 9 day(s) which contain
a total of 13 files changed, 95 insertions(+), 43 deletions(-).
The main changes are:
1) Fix refcount leak for TCP time wait and request sockets for socket lookup
related BPF helpers, from Lorenz Bauer.
2) Fix wrong verification of ARSH instruction under ALU32, from Daniel Borkmann.
3) Batch of several sockmap and related TLS fixes found while operating
more complex BPF programs with Cilium and OpenSSL, from John Fastabend.
4) Fix sockmap to read psock's ingress_msg queue before regular sk_receive_queue()
to avoid purging data upon teardown, from Lingpeng Chen.
5) Fix printing incorrect pointer in bpftool's btf_dump_ptr() in order to properly
dump a BPF map's value with BTF, from Martin KaFai Lau.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Logical block size has type unsigned short. That means that it can be at
most 32768. However, there are architectures that can run with 64k pages
(for example arm64) and on these architectures, it may be possible to
create block devices with 64k block size.
For exmaple (run this on an architecture with 64k pages):
Mount will fail with this error because it tries to read the superblock using 2-sector
access:
device-mapper: writecache: I/O is not aligned, sector 2, size 1024, block size 65536
EXT4-fs (dm-0): unable to read superblock
This patch changes the logical block size from unsigned short to unsigned
int to avoid the overflow.
Cc: stable@vger.kernel.org
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
When sockmap sock with TLS enabled is removed we cleanup bpf/psock state
and call tcp_update_ulp() to push updates to TLS ULP on top. However, we
don't push the write_space callback up and instead simply overwrite the
op with the psock stored previous op. This may or may not be correct so
to ensure we don't overwrite the TLS write space hook pass this field to
the ULP and have it fixup the ctx.
This completes a previous fix that pushed the ops through to the ULP
but at the time missed doing this for write_space, presumably because
write_space TLS hook was added around the same time.
Fixes: 95fa145479 ("bpf: sockmap/tls, close can race with map free")
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Jakub Sitnicki <jakub@cloudflare.com>
Acked-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/bpf/20200111061206.8028-4-john.fastabend@gmail.com
When a sockmap is free'd and a socket in the map is enabled with tls
we tear down the bpf context on the socket, the psock struct and state,
and then call tcp_update_ulp(). The tcp_update_ulp() call is to inform
the tls stack it needs to update its saved sock ops so that when the tls
socket is later destroyed it doesn't try to call the now destroyed psock
hooks.
This is about keeping stacked ULPs in good shape so they always have
the right set of stacked ops.
However, recently unhash() hook was removed from TLS side. But, the
sockmap/bpf side is not doing any extra work to update the unhash op
when is torn down instead expecting TLS side to manage it. So both
TLS and sockmap believe the other side is managing the op and instead
no one updates the hook so it continues to point at tcp_bpf_unhash().
When unhash hook is called we call tcp_bpf_unhash() which detects the
psock has already been destroyed and calls sk->sk_prot_unhash() which
calls tcp_bpf_unhash() yet again and so on looping and hanging the core.
To fix have sockmap tear down logic fixup the stale pointer.
Fixes: 5d92e631b8 ("net/tls: partially revert fix transition through disconnect with close")
Reported-by: syzbot+83979935eb6304f8cd46@syzkaller.appspotmail.com
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Jakub Sitnicki <jakub@cloudflare.com>
Acked-by: Song Liu <songliubraving@fb.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/bpf/20200111061206.8028-2-john.fastabend@gmail.com
[Why]
Noticed this while testing MST with the 4 ports MST hub from
StarTech.com. Sometimes can't light up monitors normally and get the
error message as 'sideband msg build failed'.
Look into aux transactions, found out that source sometimes will send
out another down request before receiving the down reply of the
previous down request. On the other hand, in drm_dp_get_one_sb_msg(),
current code doesn't handle the interleaved replies case. Hence, source
can't build up message completely and can't light up monitors.
[How]
For good compatibility, enforce source to send out one down request at a
time. Add a flag, is_waiting_for_dwn_reply, to determine if the source
can send out a down request immediately or not.
- Check the flag before calling process_single_down_tx_qlock to send out
a msg
- Set the flag when successfully send out a down request
- Clear the flag when successfully build up a down reply
- Clear the flag when find erros during sending out a down request
- Clear the flag when find errors during building up a down reply
- Clear the flag when timeout occurs during waiting for a down reply
- Use drm_dp_mst_kick_tx() to try to send another down request in queue
at the end of drm_dp_mst_wait_tx_reply() (attempt to send out messages
in queue when errors occur)
Cc: Lyude Paul <lyude@redhat.com>
Signed-off-by: Wayne Lin <Wayne.Lin@amd.com>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200113093649.11755-1-Wayne.Lin@amd.com
Anatoly has been fuzzing with kBdysch harness and reported a hang in one
of the outcomes:
0: R1=ctx(id=0,off=0,imm=0) R10=fp0
0: (85) call bpf_get_socket_cookie#46
1: R0_w=invP(id=0) R10=fp0
1: (57) r0 &= 808464432
2: R0_w=invP(id=0,umax_value=808464432,var_off=(0x0; 0x30303030)) R10=fp0
2: (14) w0 -= 810299440
3: R0_w=invP(id=0,umax_value=4294967295,var_off=(0xcf800000; 0x3077fff0)) R10=fp0
3: (c4) w0 s>>= 1
4: R0_w=invP(id=0,umin_value=1740636160,umax_value=2147221496,var_off=(0x67c00000; 0x183bfff8)) R10=fp0
4: (76) if w0 s>= 0x30303030 goto pc+216
221: R0_w=invP(id=0,umin_value=1740636160,umax_value=2147221496,var_off=(0x67c00000; 0x183bfff8)) R10=fp0
221: (95) exit
processed 6 insns (limit 1000000) [...]
Taking a closer look, the program was xlated as follows:
# ./bpftool p d x i 12
0: (85) call bpf_get_socket_cookie#7800896
1: (bf) r6 = r0
2: (57) r6 &= 808464432
3: (14) w6 -= 810299440
4: (c4) w6 s>>= 1
5: (76) if w6 s>= 0x30303030 goto pc+216
6: (05) goto pc-1
7: (05) goto pc-1
8: (05) goto pc-1
[...]
220: (05) goto pc-1
221: (05) goto pc-1
222: (95) exit
Meaning, the visible effect is very similar to f54c7898ed ("bpf: Fix
precision tracking for unbounded scalars"), that is, the fall-through
branch in the instruction 5 is considered to be never taken given the
conclusion from the min/max bounds tracking in w6, and therefore the
dead-code sanitation rewrites it as goto pc-1. However, real-life input
disagrees with verification analysis since a soft-lockup was observed.
The bug sits in the analysis of the ARSH. The definition is that we shift
the target register value right by K bits through shifting in copies of
its sign bit. In adjust_scalar_min_max_vals(), we do first coerce the
register into 32 bit mode, same happens after simulating the operation.
However, for the case of simulating the actual ARSH, we don't take the
mode into account and act as if it's always 64 bit, but location of sign
bit is different:
dst_reg->smin_value >>= umin_val;
dst_reg->smax_value >>= umin_val;
dst_reg->var_off = tnum_arshift(dst_reg->var_off, umin_val);
Consider an unknown R0 where bpf_get_socket_cookie() (or others) would
for example return 0xffff. With the above ARSH simulation, we'd see the
following results:
[...]
1: R1=ctx(id=0,off=0,imm=0) R2_w=invP65535 R10=fp0
1: (85) call bpf_get_socket_cookie#46
2: R0_w=invP(id=0) R10=fp0
2: (57) r0 &= 808464432
-> R0_runtime = 0x3030
3: R0_w=invP(id=0,umax_value=808464432,var_off=(0x0; 0x30303030)) R10=fp0
3: (14) w0 -= 810299440
-> R0_runtime = 0xcfb40000
4: R0_w=invP(id=0,umax_value=4294967295,var_off=(0xcf800000; 0x3077fff0)) R10=fp0
(0xffffffff)
4: (c4) w0 s>>= 1
-> R0_runtime = 0xe7da0000
5: R0_w=invP(id=0,umin_value=1740636160,umax_value=2147221496,var_off=(0x67c00000; 0x183bfff8)) R10=fp0
(0x67c00000) (0x7ffbfff8)
[...]
In insn 3, we have a runtime value of 0xcfb40000, which is '1100 1111 1011
0100 0000 0000 0000 0000', the result after the shift has 0xe7da0000 that
is '1110 0111 1101 1010 0000 0000 0000 0000', where the sign bit is correctly
retained in 32 bit mode. In insn4, the umax was 0xffffffff, and changed into
0x7ffbfff8 after the shift, that is, '0111 1111 1111 1011 1111 1111 1111 1000'
and means here that the simulation didn't retain the sign bit. With above
logic, the updates happen on the 64 bit min/max bounds and given we coerced
the register, the sign bits of the bounds are cleared as well, meaning, we
need to force the simulation into s32 space for 32 bit alu mode.
Verification after the fix below. We're first analyzing the fall-through branch
on 32 bit signed >= test eventually leading to rejection of the program in this
specific case:
0: R1=ctx(id=0,off=0,imm=0) R10=fp0
0: (b7) r2 = 808464432
1: R1=ctx(id=0,off=0,imm=0) R2_w=invP808464432 R10=fp0
1: (85) call bpf_get_socket_cookie#46
2: R0_w=invP(id=0) R10=fp0
2: (bf) r6 = r0
3: R0_w=invP(id=0) R6_w=invP(id=0) R10=fp0
3: (57) r6 &= 808464432
4: R0_w=invP(id=0) R6_w=invP(id=0,umax_value=808464432,var_off=(0x0; 0x30303030)) R10=fp0
4: (14) w6 -= 810299440
5: R0_w=invP(id=0) R6_w=invP(id=0,umax_value=4294967295,var_off=(0xcf800000; 0x3077fff0)) R10=fp0
5: (c4) w6 s>>= 1
6: R0_w=invP(id=0) R6_w=invP(id=0,umin_value=3888119808,umax_value=4294705144,var_off=(0xe7c00000; 0x183bfff8)) R10=fp0
(0x67c00000) (0xfffbfff8)
6: (76) if w6 s>= 0x30303030 goto pc+216
7: R0_w=invP(id=0) R6_w=invP(id=0,umin_value=3888119808,umax_value=4294705144,var_off=(0xe7c00000; 0x183bfff8)) R10=fp0
7: (30) r0 = *(u8 *)skb[808464432]
BPF_LD_[ABS|IND] uses reserved fields
processed 8 insns (limit 1000000) [...]
Fixes: 9cbe1f5a32 ("bpf/verifier: improve register value range tracking with ARSH")
Reported-by: Anatoly Trosinenko <anatoly.trosinenko@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200115204733.16648-1-daniel@iogearbox.net
Pull vfs fixes from Al Viro:
"Fixes for mountpoint_last() bugs (by converting to use of
lookup_last()) and an autofs regression fix from this cycle (caused by
follow_managed() breakage introduced in barrier fixes series)"
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
fix autofs regression caused by follow_managed() changes
reimplement path_mountpoint() with less magic
Johannes Berg says:
====================
A few fixes:
* -O3 enablement fallout, thanks to Arnd who ran this
* fixes for a few leaks, thanks to Felix
* channel 12 regulatory fix for custom regdomains
* check for a crash reported by syzbot
(NULL function is called on drivers that don't have it)
* fix TKIP replay protection after setup with some APs
(from Jouni)
* restrict obtaining some mesh data to avoid WARN_ONs
* fix deadlocks with auto-disconnect (socket owner)
* fix radar detection events with multiple devices
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
In case a radar event of CAC_FINISHED or RADAR_DETECTED
happens during another phy is during CAC we might need
to cancel that CAC.
If we got a radar in a channel that another phy is now
doing CAC on then the CAC should be canceled there.
If, for example, 2 phys doing CAC on the same channels,
or on comptable channels, once on of them will finish his
CAC the other might need to cancel his CAC, since it is no
longer relevant.
To fix that the commit adds an callback and implement it in
mac80211 to end CAC.
This commit also adds a call to said callback if after a radar
event we see the CAC is no longer relevant
Signed-off-by: Orr Mazor <Orr.Mazor@tandemg.com>
Reviewed-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Link: https://lore.kernel.org/r/20191222145449.15792-1-Orr.Mazor@tandemg.com
[slightly reformat/reword commit message]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
... and get rid of a bunch of bugs in it. Background:
the reason for path_mountpoint() is that umount() really doesn't
want attempts to revalidate the root of what it's trying to umount.
The thing we want to avoid actually happen from complete_walk();
solution was to do something parallel to normal path_lookupat()
and it both went overboard and got the boilerplate subtly
(and not so subtly) wrong.
A better solution is to do pretty much what the normal path_lookupat()
does, but instead of complete_walk() do unlazy_walk(). All it takes
to avoid that ->d_weak_revalidate() call... mountpoint_last() goes
away, along with everything it got wrong, and so does the magic around
LOOKUP_NO_REVAL.
Another source of bugs is that when we traverse mounts at the final
location (and we need to do that - umount . expects to get whatever's
overmounting ., if any, out of the lookup) we really ought to take
care of ->d_manage() - as it is, manual umount of autofs automount
in progress can lead to unpleasant surprises for the daemon. Easily
solved by using handle_lookup_down() instead of follow_mount().
Tested-by: Ian Kent <raven@themaw.net>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Pull asm-generic fixes from Arnd Bergmann:
"Here are two bugfixes from Mike Rapoport, both fixing compile-time
errors for the nds32 architecture that were recently introduced"
* tag 'asm-generic-5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/playground:
nds32: fix build failure caused by page table folding updates
asm-generic/nds32: don't redefine cacheflush primitives
Merge misc fixes from David Howells.
Two afs fixes and a key refcounting fix.
* dhowells:
afs: Fix afs_lookup() to not clobber the version on a new dentry
afs: Fix use-after-loss-of-ref
keys: Fix request_key() cache
afs_lookup() has a tracepoint to indicate the outcome of
d_splice_alias(), passing it the inode to retrieve the fid from.
However, the function gave up its ref on that inode when it called
d_splice_alias(), which may have failed and dropped the inode.
Fix this by caching the fid.
Fixes: 80548b0399 ("afs: Add more tracepoints")
Reported-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 96a2b03f28 ("mm, debug_pagelloc: use static keys to enable
debugging") has introduced a static key to reduce overhead when
debug_pagealloc is compiled in but not enabled. It relied on the
assumption that jump_label_init() is called before parse_early_param()
as in start_kernel(), so when the "debug_pagealloc=on" option is parsed,
it is safe to enable the static key.
However, it turns out multiple architectures call parse_early_param()
earlier from their setup_arch(). x86 also calls jump_label_init() even
earlier, so no issue was found while testing the commit, but same is not
true for e.g. ppc64 and s390 where the kernel would not boot with
debug_pagealloc=on as found by our QA.
To fix this without tricky changes to init code of multiple
architectures, this patch partially reverts the static key conversion
from 96a2b03f28. Init-time and non-fastpath calls (such as in arch
code) of debug_pagealloc_enabled() will again test a simple bool
variable. Fastpath mm code is converted to a new
debug_pagealloc_enabled_static() variant that relies on the static key,
which is enabled in a well-defined point in mm_init() where it's
guaranteed that jump_label_init() has been called, regardless of
architecture.
[sfr@canb.auug.org.au: export _debug_pagealloc_enabled_early]
Link: http://lkml.kernel.org/r/20200106164944.063ac07b@canb.auug.org.au
Link: http://lkml.kernel.org/r/20191219130612.23171-1-vbabka@suse.cz
Fixes: 96a2b03f28 ("mm, debug_pagelloc: use static keys to enable debugging")
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Mel Gorman <mgorman@techsingularity.net>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Qian Cai <cai@lca.pw>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently slab percpu vmstats are flushed twice: during the memcg
offlining and just before freeing the memcg structure. Each time percpu
counters are summed, added to the atomic counterparts and propagated up
by the cgroup tree.
The second flushing is required due to how recursive vmstats are
implemented: counters are batched in percpu variables on a local level,
and once a percpu value is crossing some predefined threshold, it spills
over to atomic values on the local and each ascendant levels. It means
that without flushing some numbers cached in percpu variables will be
dropped on floor each time a cgroup is destroyed. And with uptime the
error on upper levels might become noticeable.
The first flushing aims to make counters on ancestor levels more
precise. Dying cgroups may resume in the dying state for a long time.
After kmem_cache reparenting which is performed during the offlining
slab counters of the dying cgroup don't have any chances to be updated,
because any slab operations will be performed on the parent level. It
means that the inaccuracy caused by percpu batching will not decrease up
to the final destruction of the cgroup. By the original idea flushing
slab counters during the offlining should minimize the visible
inaccuracy of slab counters on the parent level.
The problem is that percpu counters are not zeroed after the first
flushing. So every cached percpu value is summed twice. It creates a
small error (up to 32 pages per cpu, but usually less) which accumulates
on parent cgroup level. After creating and destroying of thousands of
child cgroups, slab counter on parent level can be way off the real
value.
For now, let's just stop flushing slab counters on memcg offlining. It
can't be done correctly without scheduling a work on each cpu: reading
and zeroing it during css offlining can race with an asynchronous
update, which doesn't expect values to be changed underneath.
With this change, slab counters on parent level will become eventually
consistent. Once all dying children are gone, values are correct. And
if not, the error is capped by 32 * NR_CPUS pages per dying cgroup.
It's not perfect, as slab are reparented, so any updates after the
reparenting will happen on the parent level. It means that if a slab
page was allocated, a counter on child level was bumped, then the page
was reparented and freed, the annihilation of positive and negative
counter values will not happen until the child cgroup is released. It
makes slab counters different from others, and it might want us to
implement flushing in a correct form again. But it's also a question of
performance: scheduling a work on each cpu isn't free, and it's an open
question if the benefit of having more accurate counters is worth it.
We might also consider flushing all counters on offlining, not only slab
counters.
So let's fix the main problem now: make the slab counters eventually
consistent, so at least the error won't grow with uptime (or more
precisely the number of created and destroyed cgroups). And think about
the accuracy of counters separately.
Link: http://lkml.kernel.org/r/20191220042728.1045881-1-guro@fb.com
Fixes: bee07b33db ("mm: memcontrol: flush percpu slab vmstats on kmem offlining")
Signed-off-by: Roman Gushchin <guro@fb.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull RISC-V fixes from Paul Walmsley:
"Two fixes for RISC-V:
- Clear FP registers during boot when FP support is present, rather
than when they aren't present
- Move the header files associated with the SiFive L2 cache
controller to drivers/soc (where the code was recently moved)"
* tag 'riscv/for-v5.5-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
riscv: Fixup obvious bug for fp-regs reset
riscv: move sifive_l2_cache.h to include/soc
The commit 9209fb5189 ("riscv: move sifive_l2_cache.c to drivers/soc")
moves the sifive L2 cache driver to driver/soc. It did not move the
header file along with the driver. Therefore this patch moves the header
file to driver/soc
Signed-off-by: Yash Shah <yash.shah@sifive.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
[paul.walmsley@sifive.com: updated to fix the include guard]
Fixes: 9209fb5189 ("riscv: move sifive_l2_cache.c to drivers/soc")
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
The function to obtain a unique snapshot id was mistakenly typo'd as
devlink_region_shapshot_id_get. Fix this typo by renaming the function
and all of its users.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull block fixes from Jens Axboe:
"A few fixes that should go into this round.
This pull request contains two NVMe fixes via Keith, removal of a dead
function, and a fix for the bio op for read truncates (Ming)"
* tag 'block-5.5-2020-01-10' of git://git.kernel.dk/linux-block:
nvmet: fix per feat data len for get_feature
nvme: Translate more status codes to blk_status_t
fs: move guard_bio_eod() after bio_set_op_attrs
block: remove unused mp_bvec_last_segment
Pull MTD fixes from Miquel Raynal:
"MTD:
- sm_ftl: Fix NULL pointer warning.
Raw NAND:
- Cadence: fix compile testing.
- STM32: Avoid locking.
Onenand:
- Fix several sparse/build warnings.
SPI-NOR:
- Add a flag to fix interaction with Micron parts"
* tag 'mtd/fixes-for-5.5-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux:
mtd: spi-nor: Fix the writing of the Status Register on micron flashes
mtd: sm_ftl: fix NULL pointer warning
mtd: onenand: omap2: Pass correct flags for prep_dma_memcpy
mtd: onenand: samsung: Fix iomem access with regular memcpy
mtd: onenand: omap2: Fix errors in style
mtd: cadence: Fix cast to pointer from integer of different size warning
mtd: rawnand: stm32_fmc2: avoid to lock the CPU bus
Pull input fixes from Dmitry Torokhov:
"Just a few small fixups here"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: imx_sc_key - only take the valid data from SCU firmware as key state
Input: add safety guards to input_set_keycode()
Input: input_event - fix struct padding on sparc64
Input: uinput - always report EPOLLOUT
Pull networking fixes from David Miller:
1) Missing netns pointer init in arp_tables, from Florian Westphal.
2) Fix normal tcp SACK being treated as D-SACK, from Pengcheng Yang.
3) Fix divide by zero in sch_cake, from Wen Yang.
4) Len passed to skb_put_padto() is wrong in qrtr code, from Carl
Huang.
5) cmd->obj.chunk is leaked in sctp code error paths, from Xin Long.
6) cgroup bpf programs can be released out of order, fix from Roman
Gushchin.
7) Make sure stmmac debugfs entry name is changed when device name
changes, from Jiping Ma.
8) Fix memory leak in vlan_dev_set_egress_priority(), from Eric
Dumazet.
9) SKB leak in lan78xx usb driver, also from Eric Dumazet.
10) Ridiculous TCA_FQ_QUANTUM values configured can cause loops in fq
packet scheduler, reject them. From Eric Dumazet.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (69 commits)
tipc: fix wrong connect() return code
tipc: fix link overflow issue at socket shutdown
netfilter: ipset: avoid null deref when IPSET_ATTR_LINENO is present
netfilter: conntrack: dccp, sctp: handle null timeout argument
atm: eni: fix uninitialized variable warning
macvlan: do not assume mac_header is set in macvlan_broadcast()
net: sch_prio: When ungrafting, replace with FIFO
mlxsw: spectrum_qdisc: Ignore grafting of invisible FIFO
MAINTAINERS: Remove myself as co-maintainer for qcom-ethqos
gtp: fix bad unlock balance in gtp_encap_enable_socket
pkt_sched: fq: do not accept silly TCA_FQ_QUANTUM
tipc: remove meaningless assignment in Makefile
tipc: do not add socket.o to tipc-y twice
net: stmmac: dwmac-sun8i: Allow all RGMII modes
net: stmmac: dwmac-sunxi: Allow all RGMII modes
net: usb: lan78xx: fix possible skb leak
net: stmmac: Fixed link does not need MDIO Bus
vlan: vlan_changelink() should propagate errors
vlan: fix memory leak in vlan_dev_set_egress_priority
stmmac: debugfs entry name is not be changed when udev rename device name.
...
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contains Netfilter fixes for net:
1) Missing netns context in arp_tables, from Florian Westphal.
2) Underflow in flowtable reference counter, from wenxu.
3) Fix incorrect ethernet destination address in flowtable offload,
from wenxu.
4) Check for status of neighbour entry, from wenxu.
5) Fix NAT port mangling, from wenxu.
6) Unbind callbacks from destroy path to cleanup hardware properly
on flowtable removal.
7) Fix missing casting statistics timestamp, add nf_flowtable_time_stamp
and use it.
8) NULL pointer exception when timeout argument is null in conntrack
dccp and sctp protocol helpers, from Florian Westphal.
9) Possible nul-dereference in ipset with IPSET_ATTR_LINENO, also from
Florian.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull tracing fixes from Steven Rostedt:
"Various tracing fixes:
- kbuild found missing define of MCOUNT_INSN_SIZE for various build
configs
- Initialize variable to zero as gcc thinks it is used undefined (it
really isn't but the code is subtle enough that this doesn't hurt)
- Convert from do_div() to div64_ull() to prevent potential divide by
zero
- Unregister a trace point on error path in sched_wakeup tracer
- Use signed offset for archs that can have stext not be first
- A simple indentation fix (whitespace error)"
* tag 'trace-v5.5-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
tracing: Fix indentation issue
kernel/trace: Fix do not unregister tracepoints when register sched_migrate_task fail
tracing: Change offset type to s32 in preempt/irq tracepoints
ftrace: Avoid potential division by zero in function profiler
tracing: Have stack tracer compile when MCOUNT_INSN_SIZE is not defined
tracing: Define MCOUNT_INSN_SIZE when not defined without direct calls
tracing: Initialize val to zero in parse_entry of inject code
Fix up inconsistent usage of upper and lowercase letters in "Samsung"
name.
"SAMSUNG" is not an abbreviation but a regular trademarked name.
Therefore it should be written with lowercase letters starting with
capital letter.
Although advertisement materials usually use uppercase "SAMSUNG", the
lowercase version is used in all legal aspects (e.g. on Wikipedia and in
privacy/legal statements on
https://www.samsung.com/semiconductor/privacy-global/).
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull spi fixes from Mark Brown:
"A small collection of fixes here, one to make the newly added PTP
timestamping code more accurate, a few driver fixes and a fix for the
core DT binding to document the fact that we support eight wire buses"
* tag 'spi-fix-v5.5-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: Document Octal mode as valid SPI bus width
spi: spi-dw: Add lock protect dw_spi rx/tx to prevent concurrent calls
spi: spi-fsl-dspi: Fix 16-bit word order in 32-bit XSPI mode
spi: Don't look at TX buffer for PTP system timestamping
spi: uniphier: Fix FIFO threshold
Pull RTC fixes from Alexandre Belloni:
"A few fixes for this cycle. The CMOS AltCentury support broke a few
platforms with a recent BIOS so I reverted it. The mt6397 fix is not
that critical but good to have. And finally, the sun6i fix repairs
WiFi and BT on a few platforms.
Summary:
- cmos: revert AltCentury support on AMD/Hygon
- mt6397: fix alarm register overwrite
- sun6i: ensure clock is working on R40"
* tag 'rtc-5.5-2' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux:
rtc: cmos: Revert "rtc: Fix the AltCentury value on AMD/Hygon platform"
rtc: mt6397: fix alarm register overwrite
rtc: sun6i: Add support for RTC clocks on R40
This patch adds nf_flowtable_time_stamp and updates the existing code to
use it.
This patch is also implicitly fixing up hardware statistic fetching via
nf_flow_offload_stats() where casting to u32 is missing. Use
nf_flow_timeout_delta() to fix this.
Fixes: c29f74e0df ("netfilter: nf_flow_table: hardware offload support")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Acked-by: wenxu <wenxu@ucloud.cn>
After commit 85a8ce62c2 ("block: add bio_truncate to fix guard_bio_eod")
this function is unused, remove it.
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
We currently try to shrink a single zone when removing memory. We use
the zone of the first page of the memory we are removing. If that
memmap was never initialized (e.g., memory was never onlined), we will
read garbage and can trigger kernel BUGs (due to a stale pointer):
BUG: unable to handle page fault for address: 000000000000353d
#PF: supervisor write access in kernel mode
#PF: error_code(0x0002) - not-present page
PGD 0 P4D 0
Oops: 0002 [#1] SMP PTI
CPU: 1 PID: 7 Comm: kworker/u8:0 Not tainted 5.3.0-rc5-next-20190820+ #317
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.12.1-0-ga5cab58e9a3f-prebuilt.qemu.4
Workqueue: kacpi_hotplug acpi_hotplug_work_fn
RIP: 0010:clear_zone_contiguous+0x5/0x10
Code: 48 89 c6 48 89 c3 e8 2a fe ff ff 48 85 c0 75 cf 5b 5d c3 c6 85 fd 05 00 00 01 5b 5d c3 0f 1f 840
RSP: 0018:ffffad2400043c98 EFLAGS: 00010246
RAX: 0000000000000000 RBX: 0000000200000000 RCX: 0000000000000000
RDX: 0000000000200000 RSI: 0000000000140000 RDI: 0000000000002f40
RBP: 0000000140000000 R08: 0000000000000000 R09: 0000000000000001
R10: 0000000000000000 R11: 0000000000000000 R12: 0000000000140000
R13: 0000000000140000 R14: 0000000000002f40 R15: ffff9e3e7aff3680
FS: 0000000000000000(0000) GS:ffff9e3e7bb00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 000000000000353d CR3: 0000000058610000 CR4: 00000000000006e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
__remove_pages+0x4b/0x640
arch_remove_memory+0x63/0x8d
try_remove_memory+0xdb/0x130
__remove_memory+0xa/0x11
acpi_memory_device_remove+0x70/0x100
acpi_bus_trim+0x55/0x90
acpi_device_hotplug+0x227/0x3a0
acpi_hotplug_work_fn+0x1a/0x30
process_one_work+0x221/0x550
worker_thread+0x50/0x3b0
kthread+0x105/0x140
ret_from_fork+0x3a/0x50
Modules linked in:
CR2: 000000000000353d
Instead, shrink the zones when offlining memory or when onlining failed.
Introduce and use remove_pfn_range_from_zone(() for that. We now
properly shrink the zones, even if we have DIMMs whereby
- Some memory blocks fall into no zone (never onlined)
- Some memory blocks fall into multiple zones (offlined+re-onlined)
- Multiple memory blocks that fall into different zones
Drop the zone parameter (with a potential dubious value) from
__remove_pages() and __remove_section().
Link: http://lkml.kernel.org/r/20191006085646.5768-6-david@redhat.com
Fixes: f1dd2cd13c ("mm, memory_hotplug: do not associate hotadded memory to zones until online") [visible after d0dc12e86b]
Signed-off-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Oscar Salvador <osalvador@suse.de>
Cc: Michal Hocko <mhocko@suse.com>
Cc: "Matthew Wilcox (Oracle)" <willy@infradead.org>
Cc: "Aneesh Kumar K.V" <aneesh.kumar@linux.ibm.com>
Cc: Pavel Tatashin <pasha.tatashin@soleen.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Logan Gunthorpe <logang@deltatee.com>
Cc: <stable@vger.kernel.org> [5.0+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull dmaengine fixes from Vinod Koul:
"A bunch of fixes for:
- uninitialized dma_slave_caps access
- virt-dma use after free in vchan_complete()
- driver fixes for ioat, k3dma and jz4780"
* tag 'dmaengine-fix-5.5-rc5' of git://git.infradead.org/users/vkoul/slave-dma:
ioat: ioat_alloc_ring() failure handling.
dmaengine: virt-dma: Fix access after free in vchan_complete()
dmaengine: k3dma: Avoid null pointer traversal
dmaengine: dma-jz4780: Also break descriptor chains on JZ4725B
dmaengine: Fix access to uninitialized dma_slave_caps
Pull block fixes from Jens Axboe:
"Three fixes in here:
- Fix for a missing split on default memory boundary mask (4G) (Ming)
- Fix for multi-page read bio truncate (Ming)
- Fix for null_blk zone close request handling (Damien)"
* tag 'block-5.5-20200103' of git://git.kernel.dk/linux-block:
null_blk: Fix REQ_OP_ZONE_CLOSE handling
block: fix splitting segments on boundary masks
block: add bio_truncate to fix guard_bio_eod
Pull final sizeof_field conversion from Kees Cook:
"Remove now unused FIELD_SIZEOF() macro (Kees Cook)"
* tag 'sizeof_field-v5.5-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
kernel.h: Remove unused FIELD_SIZEOF()
This reverts commit 8243186f0c ("fs: remove ksys_dup()") and the
subsequent fix for it in commit 2d3145f8d2 ("early init: fix error
handling when opening /dev/console").
Trying to use filp_open() and f_dupfd() instead of pseudo-syscalls
caused more trouble than what is worth it: it requires accessing vfs
internals and it turns out there were other bugs in it too.
In particular, the file reference counting was wrong - because unlike
the original "open+2*dup" sequence it used "filp_open+3*f_dupfd" and
thus had an extra leaked file reference.
That in turn then caused odd problems with Androidx86 long after boot
becaue of how the extra reference to the console kept the session active
even after all file descriptors had been closed.
Reported-by: youling 257 <youling257@gmail.com>
Cc: Arvind Sankar <nivedita@alum.mit.edu>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
KMSAN sysbot detected a read access to an untinitialized value in the
headroom of an outgoing CAN related sk_buff. When using CAN sockets this
area is filled appropriately - but when using a packet socket this
initialization is missing.
The problematic read access occurs in the CAN receive path which can
only be triggered when the sk_buff is sent through a (virtual) CAN
interface. So we check in the sending path whether we need to perform
the missing initializations.
Fixes: d3b58c47d3 ("can: replace timestamp as unique skb attribute")
Reported-by: syzbot+b02ff0707a97e4e79ebb@syzkaller.appspotmail.com
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Tested-by: Oliver Hartkopp <socketcan@hartkopp.net>
Cc: linux-stable <stable@vger.kernel.org> # >= v4.1
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Pull networking fixes from David Miller:
1) Fix big endian overflow in nf_flow_table, from Arnd Bergmann.
2) Fix port selection on big endian in nft_tproxy, from Phil Sutter.
3) Fix precision tracking for unbound scalars in bpf verifier, from
Daniel Borkmann.
4) Fix integer overflow in socket rcvbuf check in UDP, from Antonio
Messina.
5) Do not perform a neigh confirmation during a pmtu update over a
tunnel, from Hangbin Liu.
6) Fix DMA mapping leak in dpaa_eth driver, from Madalin Bucur.
7) Various PTP fixes for sja1105 dsa driver, from Vladimir Oltean.
8) Add missing to dummy definition of of_mdiobus_child_is_phy(), from
Geert Uytterhoeven
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (54 commits)
hsr: fix slab-out-of-bounds Read in hsr_debugfs_rename()
net/sched: add delete_empty() to filters and use it in cls_flower
tcp: Fix highest_sack and highest_sack_seq
ptp: fix the race between the release of ptp_clock and cdev
net: dsa: sja1105: Reconcile the meaning of TPID and TPID2 for E/T and P/Q/R/S
Documentation: net: dsa: sja1105: Remove text about taprio base-time limitation
net: dsa: sja1105: Remove restriction of zero base-time for taprio offload
net: dsa: sja1105: Really make the PTP command read-write
net: dsa: sja1105: Take PTP egress timestamp by port, not mgmt slot
cxgb4/cxgb4vf: fix flow control display for auto negotiation
mlxsw: spectrum: Use dedicated policer for VRRP packets
mlxsw: spectrum_router: Skip loopback RIFs during MAC validation
net: stmmac: dwmac-meson8b: Fix the RGMII TX delay on Meson8b/8m2 SoCs
net/sched: act_mirred: Pull mac prior redir to non mac_header_xmit device
net_sched: sch_fq: properly set sk->sk_pacing_status
bnx2x: Fix accounting of vlan resources among the PFs
bnx2x: Use appropriate define for vlan credit
of: mdio: Add missing inline to of_mdiobus_child_is_phy() dummy
net: phy: aquantia: add suspend / resume ops for AQR105
dpaa_eth: fix DMA mapping leak
...
Revert "net/sched: cls_u32: fix refcount leak in the error path of
u32_change()", and fix the u32 refcount leak in a more generic way that
preserves the semantic of rule dumping.
On tc filters that don't support lockless insertion/removal, there is no
need to guard against concurrent insertion when a removal is in progress.
Therefore, for most of them we can avoid a full walk() when deleting, and
just decrease the refcount, like it was done on older Linux kernels.
This fixes situations where walk() was wrongly detecting a non-empty
filter, like it happened with cls_u32 in the error path of change(), thus
leading to failures in the following tdc selftests:
6aa7: (filter, u32) Add/Replace u32 with source match and invalid indev
6658: (filter, u32) Add/Replace u32 with custom hash table and invalid handle
74c2: (filter, u32) Add/Replace u32 filter with invalid hash table id
On cls_flower, and on (future) lockless filters, this check is necessary:
move all the check_empty() logic in a callback so that each filter
can have its own implementation. For cls_flower, it's sufficient to check
if no IDRs have been allocated.
This reverts commit 275c44aa19.
Changes since v1:
- document the need for delete_empty() when TCF_PROTO_OPS_DOIT_UNLOCKED
is used, thanks to Vlad Buslov
- implement delete_empty() without doing fl_walk(), thanks to Vlad Buslov
- squash revert and new fix in a single patch, to be nice with bisect
tests that run tdc on u32 filter, thanks to Dave Miller
Fixes: 275c44aa19 ("net/sched: cls_u32: fix refcount leak in the error path of u32_change()")
Fixes: 6676d5e416 ("net: sched: set dedicated tcf_walker flag when tp is empty")
Suggested-by: Jamal Hadi Salim <jhs@mojatatu.com>
Suggested-by: Vlad Buslov <vladbu@mellanox.com>
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Reviewed-by: Vlad Buslov <vladbu@mellanox.com>
Tested-by: Jamal Hadi Salim <jhs@mojatatu.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In a case when a ptp chardev (like /dev/ptp0) is open but an underlying
device is removed, closing this file leads to a race. This reproduces
easily in a kvm virtual machine:
ts# cat openptp0.c
int main() { ... fp = fopen("/dev/ptp0", "r"); ... sleep(10); }
ts# uname -r
5.5.0-rc3-46cf053e
ts# cat /proc/cmdline
... slub_debug=FZP
ts# modprobe ptp_kvm
ts# ./openptp0 &
[1] 670
opened /dev/ptp0, sleeping 10s...
ts# rmmod ptp_kvm
ts# ls /dev/ptp*
ls: cannot access '/dev/ptp*': No such file or directory
ts# ...woken up
[ 48.010809] general protection fault: 0000 [#1] SMP
[ 48.012502] CPU: 6 PID: 658 Comm: openptp0 Not tainted 5.5.0-rc3-46cf053e #25
[ 48.014624] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), ...
[ 48.016270] RIP: 0010:module_put.part.0+0x7/0x80
[ 48.017939] RSP: 0018:ffffb3850073be00 EFLAGS: 00010202
[ 48.018339] RAX: 000000006b6b6b6b RBX: 6b6b6b6b6b6b6b6b RCX: ffff89a476c00ad0
[ 48.018936] RDX: fffff65a08d3ea08 RSI: 0000000000000247 RDI: 6b6b6b6b6b6b6b6b
[ 48.019470] ... ^^^ a slub poison
[ 48.023854] Call Trace:
[ 48.024050] __fput+0x21f/0x240
[ 48.024288] task_work_run+0x79/0x90
[ 48.024555] do_exit+0x2af/0xab0
[ 48.024799] ? vfs_write+0x16a/0x190
[ 48.025082] do_group_exit+0x35/0x90
[ 48.025387] __x64_sys_exit_group+0xf/0x10
[ 48.025737] do_syscall_64+0x3d/0x130
[ 48.026056] entry_SYSCALL_64_after_hwframe+0x44/0xa9
[ 48.026479] RIP: 0033:0x7f53b12082f6
[ 48.026792] ...
[ 48.030945] Modules linked in: ptp i6300esb watchdog [last unloaded: ptp_kvm]
[ 48.045001] Fixing recursive fault but reboot is needed!
This happens in:
static void __fput(struct file *file)
{ ...
if (file->f_op->release)
file->f_op->release(inode, file); <<< cdev is kfree'd here
if (unlikely(S_ISCHR(inode->i_mode) && inode->i_cdev != NULL &&
!(mode & FMODE_PATH))) {
cdev_put(inode->i_cdev); <<< cdev fields are accessed here
Namely:
__fput()
posix_clock_release()
kref_put(&clk->kref, delete_clock) <<< the last reference
delete_clock()
delete_ptp_clock()
kfree(ptp) <<< cdev is embedded in ptp
cdev_put
module_put(p->owner) <<< *p is kfree'd, bang!
Here cdev is embedded in posix_clock which is embedded in ptp_clock.
The race happens because ptp_clock's lifetime is controlled by two
refcounts: kref and cdev.kobj in posix_clock. This is wrong.
Make ptp_clock's sysfs device a parent of cdev with cdev_device_add()
created especially for such cases. This way the parent device with its
ptp_clock is not released until all references to the cdev are released.
This adds a requirement that an initialized but not exposed struct
device should be provided to posix_clock_register() by a caller instead
of a simple dev_t.
This approach was adopted from the commit 72139dfa24 ("watchdog: Fix
the race between the release of watchdog_core_data and cdev"). See
details of the implementation in the commit 233ed09d7f ("chardev: add
helper function to register char devs with a struct device").
Link: https://lore.kernel.org/linux-fsdevel/20191125125342.6189-1-vdronov@redhat.com/T/#u
Analyzed-by: Stephen Johnston <sjohnsto@redhat.com>
Analyzed-by: Vern Lovejoy <vlovejoy@redhat.com>
Signed-off-by: Vladis Dronov <vdronov@redhat.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
