The TQP BAR space is divided into two segments. TQPs 0-1023 and TQPs
1024-1279 are in different BAR space addresses. However,
hclge_fetch_pf_reg does not distinguish the tqp space information when
reading the tqp space information. When the number of TQPs is greater
than 1024, access bar space overwriting occurs.
The problem of different segments has been considered during the
initialization of tqp.io_base. Therefore, tqp.io_base is directly used
when the queue is read in hclge_fetch_pf_reg.
The error message:
Unable to handle kernel paging request at virtual address ffff800037200000
pc : hclge_fetch_pf_reg+0x138/0x250 [hclge]
lr : hclge_get_regs+0x84/0x1d0 [hclge]
Call trace:
hclge_fetch_pf_reg+0x138/0x250 [hclge]
hclge_get_regs+0x84/0x1d0 [hclge]
hns3_get_regs+0x2c/0x50 [hns3]
ethtool_get_regs+0xf4/0x270
dev_ethtool+0x674/0x8a0
dev_ioctl+0x270/0x36c
sock_do_ioctl+0x110/0x2a0
sock_ioctl+0x2ac/0x530
__arm64_sys_ioctl+0xa8/0x100
invoke_syscall+0x4c/0x124
el0_svc_common.constprop.0+0x140/0x15c
do_el0_svc+0x30/0xd0
el0_svc+0x1c/0x2c
el0_sync_handler+0xb0/0xb4
el0_sync+0x168/0x180
Fixes: 939ccd107f ("net: hns3: move dump regs function to a separate file")
Signed-off-by: Hao Lan <lanhao@huawei.com>
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Currently the misc irq is initialized before reset_timer setup. But
it will access the reset_timer in the irq handler. So initialize
the reset_timer earlier.
Fixes: ff200099d2 ("net: hns3: remove unnecessary work in hclgevf_main")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Currently, there is a time window between misc irq enabled
and service task inited. If an interrupte is reported at
this time, it will cause warning like below:
[ 16.324639] Call trace:
[ 16.324641] __queue_delayed_work+0xb8/0xe0
[ 16.324643] mod_delayed_work_on+0x78/0xd0
[ 16.324655] hclge_errhand_task_schedule+0x58/0x90 [hclge]
[ 16.324662] hclge_misc_irq_handle+0x168/0x240 [hclge]
[ 16.324666] __handle_irq_event_percpu+0x64/0x1e0
[ 16.324667] handle_irq_event+0x80/0x170
[ 16.324670] handle_fasteoi_edge_irq+0x110/0x2bc
[ 16.324671] __handle_domain_irq+0x84/0xfc
[ 16.324673] gic_handle_irq+0x88/0x2c0
[ 16.324674] el1_irq+0xb8/0x140
[ 16.324677] arch_cpu_idle+0x18/0x40
[ 16.324679] default_idle_call+0x5c/0x1bc
[ 16.324682] cpuidle_idle_call+0x18c/0x1c4
[ 16.324684] do_idle+0x174/0x17c
[ 16.324685] cpu_startup_entry+0x30/0x6c
[ 16.324687] secondary_start_kernel+0x1a4/0x280
[ 16.324688] ---[ end trace 6aa0bff672a964aa ]---
So don't auto enable misc vector when request irq..
Fixes: 7be1b9f3e9 ("net: hns3: make hclge_service use delayed workqueue")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
This patch modifies the implementation of debugfs:
When the user process stops unexpectedly, not all data of the file system
is read. In this case, the save_buf pointer is not released. When the user
process is called next time, save_buf is used to copy the cached data
to the user space. As a result, the queried data is inconsistent. To solve
this problem, determine whether the function is invoked for the first time
based on the value of *ppos. If *ppos is 0, obtain the actual data.
Fixes: 5e69ea7ee2 ("net: hns3: refactor the debugfs process")
Signed-off-by: Hao Lan <lanhao@huawei.com>
Signed-off-by: Guangwei Zhang <zhangwangwei6@huawei.com>
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Currently, the netdev->features is configured in hns3_nic_set_features.
As a result, __netdev_update_features considers that there is no feature
difference, and the procedures of the real features are missing.
Fixes: 2a7556bb2b ("net: hns3: implement ndo_features_check ops for hns3 driver")
Signed-off-by: Hao Lan <lanhao@huawei.com>
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
When a reset type that is not supported by the driver is input, a reset
pending flag bit of the HNAE3_NONE_RESET type is generated in
reset_pending. The driver does not have a mechanism to clear this type
of error. As a result, the driver considers that the reset is not
complete. This patch provides a mechanism to clear the
HNAE3_NONE_RESET flag and the parameter of
hnae3_ae_ops.set_default_reset_request is verified.
The error message:
hns3 0000:39:01.0: cmd failed -16
hns3 0000:39:01.0: hclge device re-init failed, VF is disabled!
hns3 0000:39:01.0: failed to reset VF stack
hns3 0000:39:01.0: failed to reset VF(4)
hns3 0000:39:01.0: prepare reset(2) wait done
hns3 0000:39:01.0 eth4: already uninitialized
Use the crash tool to view struct hclgevf_dev:
struct hclgevf_dev {
...
default_reset_request = 0x20,
reset_level = HNAE3_NONE_RESET,
reset_pending = 0x100,
reset_type = HNAE3_NONE_RESET,
...
};
Fixes: 720bd5837e ("net: hns3: add set_default_reset_request in the hnae3_ae_ops")
Signed-off-by: Hao Lan <lanhao@huawei.com>
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
To avoid errors in pgtable prefectch, add a sync command to sync
io-pagtable.
This is a supplement for the previous patch.
We want all the tx packet can be handled with tx bounce buffer path.
But it depends on the remain space of the spare buffer, checked by the
hns3_can_use_tx_bounce(). In most cases, maybe 99.99%, it returns true.
But once it return false by no available space, the packet will be handled
with the former path, which will map/unmap the skb buffer.
Then the driver will face the smmu prefetch risk again.
So add a sync command in this case to avoid smmu prefectch,
just protects corner scenes.
Fixes: 295ba232a8 ("net: hns3: add device version to replace pci revision")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peiyang Wang <wangpeiyang1@huawei.com>
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The SMMU engine on HIP09 chip has a hardware issue.
SMMU pagetable prefetch features may prefetch and use a invalid PTE
even the PTE is valid at that time. This will cause the device trigger
fake pagefaults. The solution is to avoid prefetching by adding a
SYNC command when smmu mapping a iova. But the performance of nic has a
sharp drop. Then we do this workaround, always enable tx bounce buffer,
avoid mapping/unmapping on TX path.
This issue only affects HNS3, so we always enable
tx bounce buffer when smmu enabled to improve performance.
Fixes: 295ba232a8 ("net: hns3: add device version to replace pci revision")
Signed-off-by: Peiyang Wang <wangpeiyang1@huawei.com>
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
linux-firmware commit 808cba84 ("mtk_wed: add firmware for mt7988
Wireless Ethernet Dispatcher") added mt7988_wo_{0,1}.bin in the
'mediatek/mt7988' directory while driver current expects the files in
the 'mediatek' directory.
Change path in the driver header now that the firmware has been added.
Fixes: e2f64db13a ("net: ethernet: mtk_wed: introduce WED support for MT7988")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://patch.msgid.link/Zxz0GWTR5X5LdWPe@pidgin.makrotopia.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The device stores IPv6 addresses that are used for encapsulation in
linear memory that is managed by the driver.
Changing the remote address of an ip6gre net device never worked
properly, but since cited commit the following reproducer [1] would
result in a warning [2] and a memory leak [3]. The problem is that the
new remote address is never added by the driver to its hash table (and
therefore the device) and the old address is never removed from it.
Fix by programming the new address when the configuration of the ip6gre
net device changes and removing the old one. If the address did not
change, then the above would result in increasing the reference count of
the address and then decreasing it.
[1]
# ip link add name bla up type ip6gre local 2001:db8:1::1 remote 2001:db8:2::1 tos inherit ttl inherit
# ip link set dev bla type ip6gre remote 2001:db8:3::1
# ip link del dev bla
# devlink dev reload pci/0000:01:00.0
[2]
WARNING: CPU: 0 PID: 1682 at drivers/net/ethernet/mellanox/mlxsw/spectrum.c:3002 mlxsw_sp_ipv6_addr_put+0x140/0x1d0
Modules linked in:
CPU: 0 UID: 0 PID: 1682 Comm: ip Not tainted 6.12.0-rc3-custom-g86b5b55bc835 #151
Hardware name: Nvidia SN5600/VMOD0013, BIOS 5.13 05/31/2023
RIP: 0010:mlxsw_sp_ipv6_addr_put+0x140/0x1d0
[...]
Call Trace:
<TASK>
mlxsw_sp_router_netdevice_event+0x55f/0x1240
notifier_call_chain+0x5a/0xd0
call_netdevice_notifiers_info+0x39/0x90
unregister_netdevice_many_notify+0x63e/0x9d0
rtnl_dellink+0x16b/0x3a0
rtnetlink_rcv_msg+0x142/0x3f0
netlink_rcv_skb+0x50/0x100
netlink_unicast+0x242/0x390
netlink_sendmsg+0x1de/0x420
____sys_sendmsg+0x2bd/0x320
___sys_sendmsg+0x9a/0xe0
__sys_sendmsg+0x7a/0xd0
do_syscall_64+0x9e/0x1a0
entry_SYSCALL_64_after_hwframe+0x77/0x7f
[3]
unreferenced object 0xffff898081f597a0 (size 32):
comm "ip", pid 1626, jiffies 4294719324
hex dump (first 32 bytes):
20 01 0d b8 00 02 00 00 00 00 00 00 00 00 00 01 ...............
21 49 61 83 80 89 ff ff 00 00 00 00 01 00 00 00 !Ia.............
backtrace (crc fd9be911):
[<00000000df89c55d>] __kmalloc_cache_noprof+0x1da/0x260
[<00000000ff2a1ddb>] mlxsw_sp_ipv6_addr_kvdl_index_get+0x281/0x340
[<000000009ddd445d>] mlxsw_sp_router_netdevice_event+0x47b/0x1240
[<00000000743e7757>] notifier_call_chain+0x5a/0xd0
[<000000007c7b9e13>] call_netdevice_notifiers_info+0x39/0x90
[<000000002509645d>] register_netdevice+0x5f7/0x7a0
[<00000000c2e7d2a9>] ip6gre_newlink_common.isra.0+0x65/0x130
[<0000000087cd6d8d>] ip6gre_newlink+0x72/0x120
[<000000004df7c7cc>] rtnl_newlink+0x471/0xa20
[<0000000057ed632a>] rtnetlink_rcv_msg+0x142/0x3f0
[<0000000032e0d5b5>] netlink_rcv_skb+0x50/0x100
[<00000000908bca63>] netlink_unicast+0x242/0x390
[<00000000cdbe1c87>] netlink_sendmsg+0x1de/0x420
[<0000000011db153e>] ____sys_sendmsg+0x2bd/0x320
[<000000003b6d53eb>] ___sys_sendmsg+0x9a/0xe0
[<00000000cae27c62>] __sys_sendmsg+0x7a/0xd0
Fixes: cf42911523 ("mlxsw: spectrum_ipip: Use common hash table for IPv6 address mapping")
Reported-by: Maksym Yaremchuk <maksymy@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Link: https://patch.msgid.link/e91012edc5a6cb9df37b78fd377f669381facfcb.1729866134.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Tx header should be pushed for each packet which is transmitted via
Spectrum ASICs. The cited commit moved the call to skb_cow_head() from
mlxsw_sp_port_xmit() to functions which handle Tx header.
In case that mlxsw_sp->ptp_ops->txhdr_construct() is used to handle Tx
header, and txhdr_construct() is mlxsw_sp_ptp_txhdr_construct(), there is
no call for skb_cow_head() before pushing Tx header size to SKB. This flow
is relevant for Spectrum-1 and Spectrum-4, for PTP packets.
Add the missing call to skb_cow_head() to make sure that there is both
enough room to push the Tx header and that the SKB header is not cloned and
can be modified.
An additional set will be sent to net-next to centralize the handling of
the Tx header by pushing it to every packet just before transmission.
Cc: Richard Cochran <richardcochran@gmail.com>
Fixes: 24157bc69f ("mlxsw: Send PTP packets as data packets to overcome a limitation")
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Link: https://patch.msgid.link/5145780b07ebbb5d3b3570f311254a3a2d554a44.1729866134.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Johannes Berg says:
====================
wireless fixes for v6.12-rc6
Another set of fixes, mostly iwlwifi:
* fix infinite loop in 6 GHz scan if more than
255 colocated APs were reported
* revert removal of retry loops for now to work
around issues with firmware initialization on
some devices/platforms
* fix SAR table issues with some BIOSes
* fix race in suspend/debug collection
* fix memory leak in fw recovery
* fix link ID leak in AP mode for older devices
* fix sending TX power constraints
* fix link handling in FW restart
And also the stack:
* fix setting TX power from userspace with the new
chanctx emulation code for old-style drivers
* fix a memory corruption bug due to structure
embedding
* fix CQM configuration double-free when moving
between net namespaces
* tag 'wireless-2024-10-29' of https://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless:
wifi: mac80211: ieee80211_i: Fix memory corruption bug in struct ieee80211_chanctx
wifi: iwlwifi: mvm: fix 6 GHz scan construction
wifi: cfg80211: clear wdev->cqm_config pointer on free
mac80211: fix user-power when emulating chanctx
Revert "wifi: iwlwifi: remove retry loops in start"
wifi: iwlwifi: mvm: don't add default link in fw restart flow
wifi: iwlwifi: mvm: Fix response handling in iwl_mvm_send_recovery_cmd()
wifi: iwlwifi: mvm: SAR table alignment
wifi: iwlwifi: mvm: Use the sync timepoint API in suspend
wifi: iwlwifi: mvm: really send iwl_txpower_constraints_cmd
wifi: iwlwifi: mvm: don't leak a link on AP removal
====================
Link: https://patch.msgid.link/20241029093926.13750-3-johannes@sipsolutions.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The E810 Lan On Motherboard (LOM) design is vendor specific. Intel
provides the reference design, but it is up to vendor on the final
product design. For some cases, like Linux DPLL support, the static
values defined in the driver does not reflect the actual LOM design.
Current implementation of dpll pins is causing the crash on probe
of the ice driver for such DPLL enabled E810 LOM designs:
WARNING: (...) at drivers/dpll/dpll_core.c:495 dpll_pin_get+0x2c4/0x330
...
Call Trace:
<TASK>
? __warn+0x83/0x130
? dpll_pin_get+0x2c4/0x330
? report_bug+0x1b7/0x1d0
? handle_bug+0x42/0x70
? exc_invalid_op+0x18/0x70
? asm_exc_invalid_op+0x1a/0x20
? dpll_pin_get+0x117/0x330
? dpll_pin_get+0x2c4/0x330
? dpll_pin_get+0x117/0x330
ice_dpll_get_pins.isra.0+0x52/0xe0 [ice]
...
The number of dpll pins enabled by LOM vendor is greater than expected
and defined in the driver for Intel designed NICs, which causes the crash.
Prevent the crash and allow generic pin initialization within Linux DPLL
subsystem for DPLL enabled E810 LOM designs.
Newly designed solution for described issue will be based on "per HW
design" pin initialization. It requires pin information dynamically
acquired from the firmware and is already in progress, planned for
next-tree only.
Fixes: d7999f5ea6 ("ice: implement dpll interface to control cgu")
Reviewed-by: Karol Kolacinski <karol.kolacinski@intel.com>
Signed-off-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
During testing of SR-IOV, Red Hat QE encountered an issue where the
ip link up command intermittently fails for the igbvf interfaces when
using the PREEMPT_RT variant. Investigation revealed that
e1000_write_posted_mbx returns an error due to the lack of an ACK
from e1000_poll_for_ack.
The underlying issue arises from the fact that IRQs are threaded by
default under PREEMPT_RT. While the exact hardware details are not
available, it appears that the IRQ handled by igb_msix_other must
be processed before e1000_poll_for_ack times out. However,
e1000_write_posted_mbx is called with preemption disabled, leading
to a scenario where the IRQ is serviced only after the failure of
e1000_write_posted_mbx.
To resolve this, we set IRQF_NO_THREAD for the affected interrupt,
ensuring that the kernel handles it immediately, thereby preventing
the aforementioned error.
Reproducer:
#!/bin/bash
# echo 2 > /sys/class/net/ens14f0/device/sriov_numvfs
ipaddr_vlan=3
nic_test=ens14f0
vf=${nic_test}v0
while true; do
ip link set ${nic_test} mtu 1500
ip link set ${vf} mtu 1500
ip link set $vf up
ip link set ${nic_test} vf 0 vlan ${ipaddr_vlan}
ip addr add 172.30.${ipaddr_vlan}.1/24 dev ${vf}
ip addr add 2021:db8:${ipaddr_vlan}::1/64 dev ${vf}
if ! ip link show $vf | grep 'state UP'; then
echo 'Error found'
break
fi
ip link set $vf down
done
Signed-off-by: Wander Lairson Costa <wander@redhat.com>
Fixes: 9d5c824399 ("igb: PCI-Express 82575 Gigabit Ethernet driver")
Reported-by: Yuying Ma <yuma@redhat.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
In case the non-paged data of a SKB carries protocol header and protocol
payload to be transmitted on a certain platform that the DMA AXI address
width is configured to 40-bit/48-bit, or the size of the non-paged data
is bigger than TSO_MAX_BUFF_SIZE on a certain platform that the DMA AXI
address width is configured to 32-bit, then this SKB requires at least
two DMA transmit descriptors to serve it.
For example, three descriptors are allocated to split one DMA buffer
mapped from one piece of non-paged data:
dma_desc[N + 0],
dma_desc[N + 1],
dma_desc[N + 2].
Then three elements of tx_q->tx_skbuff_dma[] will be allocated to hold
extra information to be reused in stmmac_tx_clean():
tx_q->tx_skbuff_dma[N + 0],
tx_q->tx_skbuff_dma[N + 1],
tx_q->tx_skbuff_dma[N + 2].
Now we focus on tx_q->tx_skbuff_dma[entry].buf, which is the DMA buffer
address returned by DMA mapping call. stmmac_tx_clean() will try to
unmap the DMA buffer _ONLY_IF_ tx_q->tx_skbuff_dma[entry].buf
is a valid buffer address.
The expected behavior that saves DMA buffer address of this non-paged
data to tx_q->tx_skbuff_dma[entry].buf is:
tx_q->tx_skbuff_dma[N + 0].buf = NULL;
tx_q->tx_skbuff_dma[N + 1].buf = NULL;
tx_q->tx_skbuff_dma[N + 2].buf = dma_map_single();
Unfortunately, the current code misbehaves like this:
tx_q->tx_skbuff_dma[N + 0].buf = dma_map_single();
tx_q->tx_skbuff_dma[N + 1].buf = NULL;
tx_q->tx_skbuff_dma[N + 2].buf = NULL;
On the stmmac_tx_clean() side, when dma_desc[N + 0] is closed by the
DMA engine, tx_q->tx_skbuff_dma[N + 0].buf is a valid buffer address
obviously, then the DMA buffer will be unmapped immediately.
There may be a rare case that the DMA engine does not finish the
pending dma_desc[N + 1], dma_desc[N + 2] yet. Now things will go
horribly wrong, DMA is going to access a unmapped/unreferenced memory
region, corrupted data will be transmited or iommu fault will be
triggered :(
In contrast, the for-loop that maps SKB fragments behaves perfectly
as expected, and that is how the driver should do for both non-paged
data and paged frags actually.
This patch corrects DMA map/unmap sequences by fixing the array index
for tx_q->tx_skbuff_dma[entry].buf when assigning DMA buffer address.
Tested and verified on DWXGMAC CORE 3.20a
Reported-by: Suraj Jaiswal <quic_jsuraj@quicinc.com>
Fixes: f748be531d ("stmmac: support new GMAC4")
Signed-off-by: Furong Xu <0x1207@gmail.com>
Reviewed-by: Hariprasad Kelam <hkelam@marvell.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20241021061023.2162701-1-0x1207@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
KASAN reports the following UAF. The metadata_dst, which is used to
store the SCI value for macsec offload, is already freed by
metadata_dst_free() in macsec_free_netdev(), while driver still use it
for sending the packet.
To fix this issue, dst_release() is used instead to release
metadata_dst. So it is not freed instantly in macsec_free_netdev() if
still referenced by skb.
BUG: KASAN: slab-use-after-free in mlx5e_xmit+0x1e8f/0x4190 [mlx5_core]
Read of size 2 at addr ffff88813e42e038 by task kworker/7:2/714
[...]
Workqueue: mld mld_ifc_work
Call Trace:
<TASK>
dump_stack_lvl+0x51/0x60
print_report+0xc1/0x600
kasan_report+0xab/0xe0
mlx5e_xmit+0x1e8f/0x4190 [mlx5_core]
dev_hard_start_xmit+0x120/0x530
sch_direct_xmit+0x149/0x11e0
__qdisc_run+0x3ad/0x1730
__dev_queue_xmit+0x1196/0x2ed0
vlan_dev_hard_start_xmit+0x32e/0x510 [8021q]
dev_hard_start_xmit+0x120/0x530
__dev_queue_xmit+0x14a7/0x2ed0
macsec_start_xmit+0x13e9/0x2340
dev_hard_start_xmit+0x120/0x530
__dev_queue_xmit+0x14a7/0x2ed0
ip6_finish_output2+0x923/0x1a70
ip6_finish_output+0x2d7/0x970
ip6_output+0x1ce/0x3a0
NF_HOOK.constprop.0+0x15f/0x190
mld_sendpack+0x59a/0xbd0
mld_ifc_work+0x48a/0xa80
process_one_work+0x5aa/0xe50
worker_thread+0x79c/0x1290
kthread+0x28f/0x350
ret_from_fork+0x2d/0x70
ret_from_fork_asm+0x11/0x20
</TASK>
Allocated by task 3922:
kasan_save_stack+0x20/0x40
kasan_save_track+0x10/0x30
__kasan_kmalloc+0x77/0x90
__kmalloc_noprof+0x188/0x400
metadata_dst_alloc+0x1f/0x4e0
macsec_newlink+0x914/0x1410
__rtnl_newlink+0xe08/0x15b0
rtnl_newlink+0x5f/0x90
rtnetlink_rcv_msg+0x667/0xa80
netlink_rcv_skb+0x12c/0x360
netlink_unicast+0x551/0x770
netlink_sendmsg+0x72d/0xbd0
__sock_sendmsg+0xc5/0x190
____sys_sendmsg+0x52e/0x6a0
___sys_sendmsg+0xeb/0x170
__sys_sendmsg+0xb5/0x140
do_syscall_64+0x4c/0x100
entry_SYSCALL_64_after_hwframe+0x4b/0x53
Freed by task 4011:
kasan_save_stack+0x20/0x40
kasan_save_track+0x10/0x30
kasan_save_free_info+0x37/0x50
poison_slab_object+0x10c/0x190
__kasan_slab_free+0x11/0x30
kfree+0xe0/0x290
macsec_free_netdev+0x3f/0x140
netdev_run_todo+0x450/0xc70
rtnetlink_rcv_msg+0x66f/0xa80
netlink_rcv_skb+0x12c/0x360
netlink_unicast+0x551/0x770
netlink_sendmsg+0x72d/0xbd0
__sock_sendmsg+0xc5/0x190
____sys_sendmsg+0x52e/0x6a0
___sys_sendmsg+0xeb/0x170
__sys_sendmsg+0xb5/0x140
do_syscall_64+0x4c/0x100
entry_SYSCALL_64_after_hwframe+0x4b/0x53
Fixes: 0a28bfd497 ("net/macsec: Add MACsec skb_metadata_dst Tx Data path support")
Signed-off-by: Jianbo Liu <jianbol@nvidia.com>
Reviewed-by: Patrisious Haddad <phaddad@nvidia.com>
Reviewed-by: Chris Mi <cmi@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Link: https://patch.msgid.link/20241021100309.234125-1-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If more than 255 colocated APs exist for the set of all
APs found during 2.4/5 GHz scanning, then the 6 GHz scan
construction will loop forever since the loop variable
has type u8, which can never reach the number found when
that's bigger than 255, and is stored in a u32 variable.
Also move it into the loops to have a smaller scope.
Using a u32 there is fine, we limit the number of APs in
the scan list and each has a limit on the number of RNR
entries due to the frame size. With a limit of 1000 scan
results, a frame size upper bound of 4096 (really it's
more like ~2300) and a TBTT entry size of at least 11,
we get an upper bound for the number of ~372k, well in
the bounds of a u32.
Cc: stable@vger.kernel.org
Fixes: eae94cf82d ("iwlwifi: mvm: add support for 6GHz")
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=219375
Link: https://patch.msgid.link/20241023091744.f4baed5c08a1.I8b417148bbc8c5d11c101e1b8f5bf372e17bf2a7@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Revert commit dfdfe4be18 ("wifi: iwlwifi: remove retry loops in
start"), it turns out that there's an issue with the PNVM load
notification from firmware not getting processed, that this patch
has been somewhat successfully papering over. Since this is being
reported, revert the loop removal for now.
We will later at least clean this up to only attempt to retry if
there was a timeout, but currently we don't even bubble up the
failure reason to the correct layer, only returning NULL.
Fixes: dfdfe4be18 ("wifi: iwlwifi: remove retry loops in start")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Link: https://patch.msgid.link/20241022092212.4aa82a558a00.Ibdeff9c8f0d608bc97fc42024392ae763b6937b7@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When we add the vif (and its default link) in fw restart we may
override the link that already exists. We take care of this but if
link 0 is a valid MLO link, then we will re-create a default link on
mvmvif->link[0] and we'll loose the real link we had there.
In non-MLO, we need to re-create the default link upon the interface
creation, this is fine. In MLO, we'll just wait for change_vif_links()
to re-build the links.
Fixes: bf976c814c ("wifi: iwlwifi: mvm: implement link change ops")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20241010140328.385bfea1b2e9.I4a127312285ccb529cc95cc4edf6fbe1e0a136ad@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
iwl_mvm_send_ap_tx_power_constraint_cmd is a no-op if the link is not
active (we need to know the band etc.)
However, for the station case it will be called just before we set the
link to active (by calling iwl_mvm_link_changed with
the LINK_CONTEXT_MODIFY_ACTIVE bit set in the 'changed' flags and
active = true), so it will end up doing nothing.
Fix this by calling iwl_mvm_send_ap_tx_power_constraint_cmd before
iwl_mvm_link_changed.
Fixes: 6b82f4e119 ("wifi: iwlwifi: mvm: handle TPE advertised by AP")
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20241010140328.5c235fccd3f1.I2d40dea21e5547eba458565edcb4c354d094d82a@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
wireless fixes for v6.12-rc5
The first set of wireless fixes for v6.12. We have been busy and have
not been able to send this earlier, so there are more fixes than
usual. The fixes are all over, both in stack and in drivers, but
nothing special really standing out.
The MV88E6393X family of devices can run its cycle counter off
an internal 250MHz clock instead of an external 125MHz one.
Add support for this cycle counter period by adding another set
of coefficients and lowering the periodic cycle counter read interval
to compensate for faster overflows at the increased frequency.
Otherwise, the PHC runs at 2x real time in userspace and cannot be
synchronized.
Fixes: de776d0d31 ("net: dsa: mv88e6xxx: add support for mv88e6393x family")
Signed-off-by: Shenghao Yang <me@shenghaoyang.info>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Instead of relying on a fixed mapping of hardware family to cycle
counter frequency, pull this information from the
MV88E6XXX_TAI_CLOCK_PERIOD register.
This lets us support switches whose cycle counter frequencies depend on
board design.
Fixes: de776d0d31 ("net: dsa: mv88e6xxx: add support for mv88e6393x family")
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Shenghao Yang <me@shenghaoyang.info>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Instead of having them as individual fields in ptp_ops, wrap the
coefficients in a separate struct so they can be referenced together.
Fixes: de776d0d31 ("net: dsa: mv88e6xxx: add support for mv88e6393x family")
Signed-off-by: Shenghao Yang <me@shenghaoyang.info>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The existing code moves VF to the same namespace as the synthetic NIC
during netvsc_register_vf(). But, if the synthetic device is moved to a
new namespace after the VF registration, the VF won't be moved together.
To make the behavior more consistent, add a namespace check for synthetic
NIC's NETDEV_REGISTER event (generated during its move), and move the VF
if it is not in the same namespace.
Cc: stable@vger.kernel.org
Fixes: c0a41b887c ("hv_netvsc: move VF to same namespace as netvsc device")
Suggested-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/1729275922-17595-1-git-send-email-haiyangz@microsoft.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The well-known errata regarding EEE not being functional on various KSZ
switches has been refactored a few times. Recently the refactoring has
excluded several switches that the errata should also apply to.
Disable EEE for additional switches with this errata and provide
additional comments referring to the public errata document.
The original workaround for the errata was applied with a register
write to manually disable the EEE feature in MMD 7:60 which was being
applied for KSZ9477/KSZ9897/KSZ9567 switch ID's.
Then came commit 26dd2974c5 ("net: phy: micrel: Move KSZ9477 errata
fixes to PHY driver") and commit 6068e6d7ba ("net: dsa: microchip:
remove KSZ9477 PHY errata handling") which moved the errata from the
switch driver to the PHY driver but only for PHY_ID_KSZ9477 (PHY ID)
however that PHY code was dead code because an entry was never added
for PHY_ID_KSZ9477 via MODULE_DEVICE_TABLE.
This was apparently realized much later and commit 54a4e5c163 ("net:
phy: micrel: add Microchip KSZ 9477 to the device table") added the
PHY_ID_KSZ9477 to the PHY driver but as the errata was only being
applied to PHY_ID_KSZ9477 it's not completely clear what switches
that relates to.
Later commit 6149db4997 ("net: phy: micrel: fix KSZ9477 PHY issues
after suspend/resume") breaks this again for all but KSZ9897 by only
applying the errata for that PHY ID.
Following that this was affected with commit 08c6d8bae48c("net: phy:
Provide Module 4 KSZ9477 errata (DS80000754C)") which removes
the blatant register write to MMD 7:60 and replaces it by
setting phydev->eee_broken_modes = -1 so that the generic phy-c45 code
disables EEE but this is only done for the KSZ9477_CHIP_ID (Switch ID).
Lastly commit 0411f73c13 ("net: dsa: microchip: disable EEE for
KSZ8567/KSZ9567/KSZ9896/KSZ9897.") adds some additional switches
that were missing to the errata due to the previous changes.
This commit adds an additional set of switches.
Fixes: 0411f73c13 ("net: dsa: microchip: disable EEE for KSZ8567/KSZ9567/KSZ9896/KSZ9897.")
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://patch.msgid.link/20241018160658.781564-1-tharvey@gateworks.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
It was reported that after resume from suspend a PCI error is logged
and connectivity is broken. Error message is:
PCI error (cmd = 0x0407, status_errs = 0x0000)
The message seems to be a red herring as none of the error bits is set,
and the PCI command register value also is normal. Exception handling
for a PCI error includes a chip reset what apparently brakes connectivity
here. The interrupt status bit triggering the PCI error handling isn't
actually used on PCIe chip versions, so it's not clear why this bit is
set by the chip. Fix this by ignoring this bit on PCIe chip versions.
Fixes: 0e4851502f ("r8169: merge with version 8.001.00 of Realtek's r8168 driver")
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=219388
Tested-by: Atlas Yu <atlas.yu@canonical.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/78e2f535-438f-4212-ad94-a77637ac6c9c@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The fix for MAC addresses broke detection of the naming convention
because it gave network devices no random MAC before bind()
was called. This means that the check for the local assignment bit
was always negative as the address was zeroed from allocation,
instead of from overwriting the MAC with a unique hardware address.
The correct check for whether bind() has altered the MAC is
done with is_zero_ether_addr
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Reported-by: Greg Thelen <gthelen@google.com>
Diagnosed-by: John Sperbeck <jsperbeck@google.com>
Fixes: bab8eb0dd4 ("usbnet: modern method to get random MAC")
Link: https://patch.msgid.link/20241017071849.389636-1-oneukum@suse.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Static analysis on linux-next has detected the following issue
in function virtnet_stats_ctx_init, in drivers/net/virtio_net.c :
if (vi->device_stats_cap & VIRTIO_NET_STATS_TYPE_CVQ) {
queue_type = VIRTNET_Q_TYPE_CQ;
ctx->bitmap[queue_type] |= VIRTIO_NET_STATS_TYPE_CVQ;
ctx->desc_num[queue_type] += ARRAY_SIZE(virtnet_stats_cvq_desc);
ctx->size[queue_type] += sizeof(struct virtio_net_stats_cvq);
}
ctx->bitmap is declared as a u32 however it is being bit-wise or'd with
VIRTIO_NET_STATS_TYPE_CVQ and this is defined as 1 << 32:
include/uapi/linux/virtio_net.h:#define VIRTIO_NET_STATS_TYPE_CVQ (1ULL << 32)
..and hence the bit-wise or operation won't set any bits in ctx->bitmap
because 1ULL < 32 is too wide for a u32.
In fact, the field is read into a u64:
u64 offset, bitmap;
....
bitmap = ctx->bitmap[queue_type];
so to fix, it is enough to make bitmap an array of u64.
Fixes: 941168f8b4 ("virtio_net: support device stats")
Reported-by: "Colin King (gmail)" <colin.i.king@gmail.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Link: https://patch.msgid.link/53e2bd6728136d5916e384a7840e5dc7eebff832.1729099611.git.mst@redhat.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
In mac_probe() there are multiple calls to of_find_device_by_node(),
fman_bind() and fman_port_bind() which takes references to of_dev->dev.
Not all references taken by these calls are released later on error path
in mac_probe() and in mac_remove() which lead to reference leaks.
Add references release.
Fixes: 3933961682 ("fsl/fman: Add FMan MAC driver")
Signed-off-by: Aleksandr Mishin <amishin@t-argos.ru>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
In mac_probe() there are calls to of_find_device_by_node() which takes
references to of_dev->dev. These references are not saved and not released
later on error path in mac_probe() and in mac_remove().
Add new fields into mac_device structure to save references taken for
future use in mac_probe() and mac_remove().
This is a preparation for further reference leaks fix.
Signed-off-by: Aleksandr Mishin <amishin@t-argos.ru>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
mv88e6393x_port_set_policy doesn't correctly shift the ptr value when
converting the policy format between the old and new styles, so the
target register ends up with the ptr being written over the data bits.
Shift the pointer to align with the format expected by
mv88e6393x_port_policy_write().
Fixes: 6584b26020 ("net: dsa: mv88e6xxx: implement .port_set_policy for Amethyst")
Signed-off-by: Peter Rashleigh <peter@rashleigh.ca>
Reviewed-by: Simon Horman <horms@kernel.org>
Message-ID: <20241016040822.3917-1-peter@rashleigh.ca>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
build_skb() returns NULL in case of a memory allocation failure so handle
it inside __octep_oq_process_rx() to avoid NULL pointer dereference.
__octep_oq_process_rx() is called during NAPI polling by the driver. If
skb allocation fails, keep on pulling packets out of the Rx DMA queue: we
shouldn't break the polling immediately and thus falsely indicate to the
octep_napi_poll() that the Rx pressure is going down. As there is no
associated skb in this case, don't process the packets and don't push them
up the network stack - they are skipped.
Helper function is implemented to unmmap/flush all the fragment buffers
used by the dropped packet. 'alloc_failures' counter is incremented to
mark the skb allocation error in driver statistics.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: 37d79d0596 ("octeon_ep: add Tx/Rx processing and interrupt support")
Suggested-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Aleksandr Mishin <amishin@t-argos.ru>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
