This pull request contains Broadcom ARM/ARM64/MIPS based SoCs changes
for 5.1, please pull the following:
- Stefan updates the BCM2835 SoC driver with downstream properties and
uses that to implement a reboot notifier to tell the VC4 firmware when
Linux on the ARM CPU is rebooting
- Eric adds a proper power domain driver for the BCM283x SoCs and
updates a bunch of drivers to have a better and clearer Device Tree
definition to support power domains/breaking up of functionality. This
requires converting the existing watchdog driver into a MFD and then
breaking up the functionality into separate drivers and finally
updating the DTS files to leverage the power domains information.
- Wei provides a fix for making a symbol static
* tag 'arm-soc/for-5.1/drivers' of https://github.com/Broadcom/stblinux:
ARM: bcm283x: Switch V3D over to using the PM driver instead of firmware.
ARM: bcm283x: Extend the WDT DT node out to cover the whole PM block. (v4)
soc: bcm: bcm2835-pm: Make local symbol static
soc: bcm: Make PM driver default for BCM2835
soc: bcm: bcm2835-pm: Add support for power domains under a new binding.
bcm2835-pm: Move bcm2835-watchdog's DT probe to an MFD.
dt-bindings: soc: Add a new binding for the BCM2835 PM node. (v4)
firmware: raspberrypi: notify VC4 firmware of a reboot
soc: bcm2835: sync firmware properties with downstream
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reset controller changes for v5.1
This adds the include/linux/reset directory to MAINTAINERS for reset
specific headers and adds headers for sunxi and socfpga in there to
get rid of a few extern function declarations.
There is a new reset driver for the Broadcom STB reset controller and
the i.MX7 system reset controller driver is extended to support i.MX8MQ
as well. Finally, there is a new header with reset id constants for
the Meson G12A SoC, which has a reset controller identical to Meson AXG
and thus can reuse its driver and DT bindings.
* tag 'reset-for-5.1' of git://git.pengutronix.de/git/pza/linux:
dt-bindings: reset: meson: add g12a bindings
reset: imx7: Add support for i.MX8MQ IP block variant
reset: imx7: Add plubming to support multiple IP variants
reset: Add Broadcom STB SW_INIT reset controller driver
dt-bindings: reset: Add document for Broadcom STB reset controller
reset: socfpga: declare socfpga_reset_init in a header file
reset: sunxi: declare sun6i_reset_init in a header file
MAINTAINERS: use include/linux/reset for reset controller related headers
dt-bindings: reset: imx7: Document usage on i.MX8MQ SoCs
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The GRAFX domain only contains V3D, and this driver should be the only
accessor of V3D (firmware usage gets disabled when V3D is in the DT),
so we can safely make Linux control the GRAFX and GRAFX_V3D power
domains.
Signed-off-by: Eric Anholt <eric@anholt.net>
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
It was covering part of the PM block's range, up to the WDT regs. To
support the rest of the PM block's functionality, we need the full
register range plus the AXI Async Bridge regs for PM sequencing.
This doesn't convert any of the consumers over to the new binding yet,
since we will need to be careful in coordinating our usage of firmware
services that might power domains on and off versus the bcm2835-pm
driver's access of those same domains.
Signed-off-by: Eric Anholt <eric@anholt.net>
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Avoid declaring extern functions in c files. To make sure function
definition and usage don't get out of sync, declare socfpga_reset_init
in a common header.
Suggested-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Dinh Nguyen <dinguyen@kernel.org>
Avoid declaring extern functions in c files. To make sure function
definition and usage don't get out of sync, declare sun6i_reset_init
in a common header.
Suggested-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Pull x86 fixes from Thomas Gleixner:
"A set of fixes for x86:
- Fix the swapped outb() parameters in the KASLR code
- Fix the PKEY handling at fork which missed to preserve the pkey
state for the child. Comes with a test case to validate that.
- Fix the entry stack handling for XEN PV to respect that XEN PV
systems enter the function already on the current thread stack and
not on the trampoline.
- Fix kexec load failure caused by using a stale value when the
kexec_buf structure is reused for subsequent allocations.
- Fix a bogus sizeof() in the memory encryption code
- Enforce PCI dependency for the Intel Low Power Subsystem
- Enforce PCI_LOCKLESS_CONFIG when PCI is enabled"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/Kconfig: Select PCI_LOCKLESS_CONFIG if PCI is enabled
x86/entry/64/compat: Fix stack switching for XEN PV
x86/kexec: Fix a kexec_file_load() failure
x86/mm/mem_encrypt: Fix erroneous sizeof()
x86/selftests/pkeys: Fork() to check for state being preserved
x86/pkeys: Properly copy pkey state at fork()
x86/kaslr: Fix incorrect i8254 outb() parameters
x86/intel/lpss: Make PCI dependency explicit
Pull x86 timer fixes from Thomas Gleixner:
"Two commits which were missed to be sent during the merge window.
- The TSC calibration fix turns out to be more urgent as recent
Skylake-X systems seem to have massive trouble with calibration
disturbance. This should go back into stable for that reason and it
the risk of breakage is rather low.
- Drop an unused define"
* 'x86-timers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/hpet: Remove unused FSEC_PER_NSEC define
x86/tsc: Make calibration refinement more robust
Pull KVM fixes from Paolo Bonzini:
"Quite a few fixes for x86: nested virtualization save/restore, AMD
nested virtualization and virtual APIC, 32-bit fixes, an important fix
to restore operation on older processors, and a bunch of hyper-v
bugfixes. Several are marked stable.
There are also fixes for GCC warnings and for a GCC/objtool interaction"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: x86: Mark expected switch fall-throughs
KVM: x86: fix TRACE_INCLUDE_PATH and remove -I. header search paths
KVM: selftests: check returned evmcs version range
x86/kvm/hyper-v: nested_enable_evmcs() sets vmcs_version incorrectly
KVM: VMX: Move vmx_vcpu_run()'s VM-Enter asm blob to a helper function
kvm: selftests: Fix region overlap check in kvm_util
kvm: vmx: fix some -Wmissing-prototypes warnings
KVM: nSVM: clear events pending from svm_complete_interrupts() when exiting to L1
svm: Fix AVIC incomplete IPI emulation
svm: Add warning message for AVIC IPI invalid target
KVM: x86: WARN_ONCE if sending a PV IPI returns a fatal error
KVM: x86: Fix PV IPIs for 32-bit KVM host
x86/kvm/hyper-v: recommend using eVMCS only when it is enabled
x86/kvm/hyper-v: don't recommend doing reset via synthetic MSR
kvm: x86/vmx: Use kzalloc for cached_vmcs12
KVM: VMX: Use the correct field var when clearing VM_ENTRY_LOAD_IA32_PERF_GLOBAL_CTRL
KVM: x86: Fix single-step debugging
x86/kvm/hyper-v: don't announce GUEST IDLE MSR support
Pull dma-mapping fix from Christoph Hellwig:
"Fix a xen-swiotlb regression on arm64"
* tag 'dma-mapping-5.0-2' of git://git.infradead.org/users/hch/dma-mapping:
arm64/xen: fix xen-swiotlb cache flushing
In preparation to enabling -Wimplicit-fallthrough, mark switch
cases where we are expecting to fall through.
This patch fixes the following warnings:
arch/x86/kvm/lapic.c:1037:27: warning: this statement may fall through [-Wimplicit-fallthrough=]
arch/x86/kvm/lapic.c:1876:3: warning: this statement may fall through [-Wimplicit-fallthrough=]
arch/x86/kvm/hyperv.c:1637:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
arch/x86/kvm/svm.c:4396:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
arch/x86/kvm/mmu.c:4372:36: warning: this statement may fall through [-Wimplicit-fallthrough=]
arch/x86/kvm/x86.c:3835:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
arch/x86/kvm/x86.c:7938:23: warning: this statement may fall through [-Wimplicit-fallthrough=]
arch/x86/kvm/vmx/vmx.c:2015:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
arch/x86/kvm/vmx/vmx.c:1773:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
Warning level 3 was used: -Wimplicit-fallthrough=3
This patch is part of the ongoing efforts to enabling -Wimplicit-fallthrough.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The header search path -I. in kernel Makefiles is very suspicious;
it allows the compiler to search for headers in the top of $(srctree),
where obviously no header file exists.
The reason of having -I. here is to make the incorrectly set
TRACE_INCLUDE_PATH working.
As the comment block in include/trace/define_trace.h says,
TRACE_INCLUDE_PATH should be a relative path to the define_trace.h
Fix the TRACE_INCLUDE_PATH, and remove the iffy include paths.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Commit e2e871ab2f ("x86/kvm/hyper-v: Introduce nested_get_evmcs_version()
helper") broke EVMCS enablement: to set vmcs_version we now call
nested_get_evmcs_version() but this function checks
enlightened_vmcs_enabled flag which is not yet set so we end up returning
zero.
Fix the issue by re-arranging things in nested_enable_evmcs().
Fixes: e2e871ab2f ("x86/kvm/hyper-v: Introduce nested_get_evmcs_version() helper")
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
...along with the function's STACK_FRAME_NON_STANDARD tag. Moving the
asm blob results in a significantly smaller amount of code that is
marked with STACK_FRAME_NON_STANDARD, which makes it far less likely
that gcc will split the function and trigger a spurious objtool warning.
As a bonus, removing STACK_FRAME_NON_STANDARD from vmx_vcpu_run() allows
the bulk of code to be properly checked by objtool.
Because %rbp is not loaded via VMCS fields, vmx_vcpu_run() must manually
save/restore the host's RBP and load the guest's RBP prior to calling
vmx_vmenter(). Modifying %rbp triggers objtool's stack validation code,
and so vmx_vcpu_run() is tagged with STACK_FRAME_NON_STANDARD since it's
impossible to avoid modifying %rbp.
Unfortunately, vmx_vcpu_run() is also a gigantic function that gcc will
split into separate functions, e.g. so that pieces of the function can
be inlined. Splitting the function means that the compiled Elf file
will contain one or more vmx_vcpu_run.part.* functions in addition to
a vmx_vcpu_run function. Depending on where the function is split,
objtool may warn about a "call without frame pointer save/setup" in
vmx_vcpu_run.part.* since objtool's stack validation looks for exact
names when whitelisting functions tagged with STACK_FRAME_NON_STANDARD.
Up until recently, the undesirable function splitting was effectively
blocked because vmx_vcpu_run() was tagged with __noclone. At the time,
__noclone had an unintended side effect that put vmx_vcpu_run() into a
separate optimization unit, which in turn prevented gcc from inlining
the function (or any of its own function calls) and thus eliminated gcc's
motivation to split the function. Removing the __noclone attribute
allowed gcc to optimize vmx_vcpu_run(), exposing the objtool warning.
Kudos to Qian Cai for root causing that the fnsplit optimization is what
caused objtool to complain.
Fixes: 453eafbe65 ("KVM: VMX: Move VM-Enter + VM-Exit handling to non-inline sub-routines")
Tested-by: Qian Cai <cai@lca.pw>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
We get some warnings when building kernel with W=1:
arch/x86/kvm/vmx/vmx.c:426:5: warning: no previous prototype for ‘kvm_fill_hv_flush_list_func’ [-Wmissing-prototypes]
arch/x86/kvm/vmx/nested.c:58:6: warning: no previous prototype for ‘init_vmcs_shadow_fields’ [-Wmissing-prototypes]
Make them static to fix this.
Signed-off-by: Yi Wang <wang.yi59@zte.com.cn>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
kvm-unit-tests' eventinj "NMI failing on IDT" test results in NMI being
delivered to the host (L1) when it's running nested. The problem seems to
be: svm_complete_interrupts() raises 'nmi_injected' flag but later we
decide to reflect EXIT_NPF to L1. The flag remains pending and we do NMI
injection upon entry so it got delivered to L1 instead of L2.
It seems that VMX code solves the same issue in prepare_vmcs12(), this was
introduced with code refactoring in commit 5f3d579997 ("KVM: nVMX: Rework
event injection and recovery").
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
In case of incomplete IPI with invalid interrupt type, the current
SVM driver does not properly emulate the IPI, and fails to boot
FreeBSD guests with multiple vcpus when enabling AVIC.
Fix this by update APIC ICR high/low registers, which also
emulate sending the IPI.
Signed-off-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Print warning message when IPI target ID is invalid due to one of
the following reasons:
* In logical mode: cluster > max_cluster (64)
* In physical mode: target > max_physical (512)
* Address is not present in the physical or logical ID tables
Signed-off-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
KVM hypercalls return a negative value error code in case of a fatal
error, e.g. when the hypercall isn't supported or was made with invalid
parameters. WARN_ONCE on fatal errors when sending PV IPIs as any such
error all but guarantees an SMP system will hang due to a missing IPI.
Fixes: aaffcfd1e8 ("KVM: X86: Implement PV IPIs in linux guest")
Cc: stable@vger.kernel.org
Cc: Wanpeng Li <wanpengli@tencent.com>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The recognition of the KVM_HC_SEND_IPI hypercall was unintentionally
wrapped in "#ifdef CONFIG_X86_64", causing 32-bit KVM hosts to reject
any and all PV IPI requests despite advertising the feature. This
results in all KVM paravirtualized guests hanging during SMP boot due
to IPIs never being delivered.
Fixes: 4180bf1b65 ("KVM: X86: Implement "send IPI" hypercall")
Cc: stable@vger.kernel.org
Cc: Wanpeng Li <wanpengli@tencent.com>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
We shouldn't probably be suggesting using Enlightened VMCS when it's not
enabled (not supported from guest's point of view). Hyper-V on KVM seems
to be fine either way but let's be consistent.
Fixes: 2bc39970e9 ("x86/kvm/hyper-v: Introduce KVM_GET_SUPPORTED_HV_CPUID")
Reviewed-by: Liran Alon <liran.alon@oracle.com>
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
System reset through synthetic MSR is not recommended neither by genuine
Hyper-V nor my QEMU.
Fixes: 2bc39970e9 ("x86/kvm/hyper-v: Introduce KVM_GET_SUPPORTED_HV_CPUID")
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Reviewed-by: Liran Alon <liran.alon@oracle.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Fix a recently introduced bug that results in the wrong VMCS control
field being updated when applying a IA32_PERF_GLOBAL_CTRL errata.
Fixes: c73da3fcab ("KVM: VMX: Properly handle dynamic VM Entry/Exit controls")
Reported-by: Harald Arnesen <harald@skogtun.org>
Tested-by: Harald Arnesen <harald@skogtun.org>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The single-step debugging of KVM guests on x86 is broken: if we run
gdb 'stepi' command at the breakpoint when the guest interrupts are
enabled, RIP always jumps to native_apic_mem_write(). Then other
nasty effects follow.
Long investigation showed that on Jun 7, 2017 the
commit c8401dda2f ("KVM: x86: fix singlestepping over syscall")
introduced the kvm_run.debug corruption: kvm_vcpu_do_singlestep() can
be called without X86_EFLAGS_TF set.
Let's fix it. Please consider that for -stable.
Signed-off-by: Alexander Popov <alex.popov@linux.com>
Cc: stable@vger.kernel.org
Fixes: c8401dda2f ("KVM: x86: fix singlestepping over syscall")
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
HV_X64_MSR_GUEST_IDLE_AVAILABLE appeared in kvm_vcpu_ioctl_get_hv_cpuid()
by mistake: it announces support for HV_X64_MSR_GUEST_IDLE (0x400000F0)
which we don't support in KVM (yet).
Fixes: 2bc39970e9 ("x86/kvm/hyper-v: Introduce KVM_GET_SUPPORTED_HV_CPUID")
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Xen-swiotlb hooks into the arm/arm64 arch code through a copy of the DMA
DMA mapping operations stored in the struct device arch data.
Switching arm64 to use the direct calls for the merged DMA direct /
swiotlb code broke this scheme. Replace the indirect calls with
direct-calls in xen-swiotlb as well to fix this problem.
Fixes: 356da6d0cd ("dma-mapping: bypass indirect calls for dma-direct")
Reported-by: Julien Grall <julien.grall@arm.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Stefano Stabellini <sstabellini@kernel.org>
Pull s390 fixes from Martin Schwidefsky:
- Do not claim to run under z/VM if the hypervisor can not be
identified
- Fix crashes due to outdated ASCEs in CR1
- Avoid a deadlock in regard to CPU hotplug
- Really fix the vdso mapping issue for compat tasks
- Avoid crash on restart due to an incorrect stack address
* tag 's390-5.0-2' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/smp: Fix calling smp_call_ipl_cpu() from ipl CPU
s390/vdso: correct vdso mapping for compat tasks
s390/smp: fix CPU hotplug deadlock with CPU rescan
s390/mm: always force a load of the primary ASCE on context switch
s390/early: improve machine detection
After commit
5d32a66541 ("PCI/ACPI: Allow ACPI to be built without CONFIG_PCI set")
dependencies on CONFIG_PCI that previously were satisfied implicitly
through dependencies on CONFIG_ACPI have to be specified directly.
PCI_LOCKLESS_CONFIG depends on PCI but this dependency has not been
mentioned in the Kconfig so add an explicit dependency here and fix
WARNING: unmet direct dependencies detected for PCI_LOCKLESS_CONFIG
Depends on [n]: PCI [=n]
Selected by [y]:
- X86 [=y]
Fixes: 5d32a66541 ("PCI/ACPI: Allow ACPI to be built without CONFIG_PCI set")
Signed-off-by: Sinan Kaya <okaya@kernel.org>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-acpi@vger.kernel.org
Cc: x86-ml <x86@kernel.org>
Link: https://lkml.kernel.org/r/20190121231958.28255-2-okaya@kernel.org
Pull ARC architecture updates from Vineet Gupta:
- Perf support for raw events
- boot log printing: return stack, action points
- fix memset to avoid prefetchw bleeding past end of buffer
- do_page_fault fix for mmap_sem held while returning to userspace
- other misc fixes
* tag 'arc-5.0-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
ARCv2: lib: memeset: fix doing prefetchw outside of buffer
ARC: mm: do_page_fault fixes#1: relinquish mmap_sem if signal arrives while handle_mm_fault
ARC: show_regs: lockdep: re-enable preemption
ARC: show_regs: lockdep: avoid page allocator...
ARC: perf: avoid kernel killing where it is possible
ARC: perf: move HW events mapping to separate function
ARC: perf: introduce Kernel PMU events support
ARC: perf: trivial code cleanup
ARC: perf: map generic branches to correct hardware condition
ARC: adjust memblock_reserve of kernel memory
arc: remove redundant kernel-space generic-y
ARC: fix __ffs return value to avoid build warnings
ARC: boot log: print Action point details
ARCv2: boot log: BPU return stack depth
Commit 594cc251fd ("make 'user_access_begin()' do 'access_ok()'")
makes the access_ok() check part of the user_access_begin() preceding a
series of 'unsafe' accesses. This has the desirable effect of ensuring
that all 'unsafe' accesses have been range-checked, without having to
pick through all of the callsites to verify whether the appropriate
checking has been made.
However, the consolidated range check does not inhibit speculation, so
it is still up to the caller to ensure that they are not susceptible to
any speculative side-channel attacks for user addresses that ultimately
fail the access_ok() check.
This is an oversight, so use __uaccess_begin_nospec() to ensure that
speculation is inhibited until the access_ok() check has passed.
Reported-by: Julien Thierry <julien.thierry@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull arm64 fixes from Will Deacon:
"Three arm64 fixes for -rc3.
We've plugged a couple of nasty issues involving KASLR-enabled
kernels, and removed a redundant #define that was introduced as part
of the KHWASAN fixes from akpm at -rc2.
- Fix broken kpti page-table rewrite in bizarre KASLR configuration
- Fix module loading with KASLR
- Remove redundant definition of ARCH_SLAB_MINALIGN"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
kasan, arm64: remove redundant ARCH_SLAB_MINALIGN define
arm64: kaslr: ensure randomized quantities are clean to the PoC
arm64: kpti: Update arm64_kernel_use_ng_mappings() when forced on
Pull MIPS fixes from Paul Burton:
- Fix IPI handling for Lantiq SoCs, which was broken by changes made
back in v4.12.
- Enable OF/DT serial support in ath79_defconfig to give us working
serial by default.
- Fix 64b builds for the Jazz platform.
- Set up a struct device for the BCM47xx SoC to allow BCM47xx drivers
to perform DMA again following the major DMA mapping changes made in
v4.19.
- Disable MSI on Cavium Octeon systems when the pcie_disable command
line parameter introduced in v3.3 is used, in order to avoid
inadvetently accessing PCIe controller registers despite the command
line.
- Fix a build failure for Cavium Octeon kernels with kexec enabled,
introduced in v4.20.
- Fix a regression in the behaviour of semctl/shmctl/msgctl IPC
syscalls for kernels including n32 support but not o32 support caused
by some cleanup in v3.19.
* tag 'mips_fixes_5.0_2' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux:
MIPS: OCTEON: fix kexec support
mips: fix n32 compat_ipc_parse_version
Disable MSI also when pcie-octeon.pcie_disable on
MIPS: BCM47XX: Setup struct device for the SoC
MIPS: jazz: fix 64bit build
MIPS: ath79: Enable OF serial ports in the default config
MIPS: lantiq: Use CP0_LEGACY_COMPARE_IRQ
MIPS: lantiq: Fix IPI interrupt handling
Pull Devicetree fix from Rob Herring:
"A single build fix for powerpc due to device_node.type removal"
* tag 'devicetree-fixes-for-5.0-2' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
powerpc: chrp: Use of_node_is_type to access device_type
Pull powerpc fixes from Michael Ellerman:
"A couple of weeks of fixes.
There's one fix for an oops on Power9 machines with Open CAPI
adapters.
And a fix for probable memory corruption in some of the new NPU code,
caught by smatch though and not seen in the wild.
Plus a few other minor fixes.
There's one non-fix which is the perf_regs change. That was sent
during the merge window but I accidentally only merged the first of
two patches in the series. It's been in linux-next so hopefully
doesn't conflict with anything in acme's tree.
Thanks to: Alexey Kardashevskiy, Andrew Donnellan, Breno Leitao,
Christian Lamparter, Christophe Leroy, Dan Carpenter, Frederic Barrat,
Greg Kurz, Jason A. Donenfeld, Madhavan Srinivasan"
* tag 'powerpc-5.0-3' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/syscalls: Fix syscall tracing
powerpc/pseries: Fix build break due to pnv_npu2_init()
powerpc/4xx/ocm: Fix fix for phys_addr_t printf warnings
powerpc/powernv/npu: Fix oops in pnv_try_setup_npu_table_group()
powerpc/tm: Limit TM code inside PPC_TRANSACTIONAL_MEM
powerpc/8xx: fix setting of pagetable for Abatron BDI debug tool.
powerpc/powernv/npu: Allocate enough memory in pnv_try_setup_npu_table_group()
powerpc/perf: Update perf_regs structure to include MMCRA
Pull xen fixes from Juergen Gross:
- Several fixes for the Xen pvcalls drivers (1 fix for the backend and
8 for the frontend).
- A fix for a rather longstanding bug in the Xen sched_clock()
interface which led to weird time jumps when migrating the system.
- A fix for avoiding accesses to x2apic MSRs in Xen PV guests.
* tag 'for-linus-5.0-rc3-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen: Fix x86 sched_clock() interface for xen
pvcalls-front: fix potential null dereference
always clear the X2APIC_ENABLE bit for PV guest
pvcalls-front: Avoid get_free_pages(GFP_KERNEL) under spinlock
xen/pvcalls: remove set but not used variable 'intf'
pvcalls-back: set -ENOTCONN in pvcalls_conn_back_read
pvcalls-front: don't return error when the ring is full
pvcalls-front: properly allocate sk
pvcalls-front: don't try to free unallocated rings
pvcalls-front: read all data before closing the connection
Pull ACPI fixes from Rafael Wysocki:
"These fix an ACPI initialization ordering issue introduced in the 4.17
time frame and causing functional problems to appear on multiple
systems and fix some fallout of the recent change to enable building
kernels with ACPI support and without PCI.
Specifics:
- Restore the ACPI initialization ordering changed implicitly by the
module-level AML handling rework during the 4.17 development cycle
that caused the EC address space handler based on information from
ECDT to be set up before loading AML definition blocks, making it
effectively not accessible by AML on some systems that don't work
as expected any more (Rafael Wysocki).
- Add direct dependencies on PCI to Kconfig in multiple places for
code that depends on both ACPI and PCI, but the PCI dependency was
implicitly satisfied by the ACPI dependency before, to prevent
invalid configurations from being created, for example by
randconfig (Sinan Kaya)"
* tag 'acpi-5.0-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI: EC: Look for ECDT EC after calling acpi_load_tables()
drivers: thermal: int340x_thermal: Make PCI dependency explicit
x86/intel/lpss: Make PCI dependency explicit
platform/x86: apple-gmux: Make PCI dependency explicit
platform/x86: intel_pmc: Make PCI dependency explicit
platform/x86: intel_ips: make PCI dependency explicit
vga-switcheroo: make PCI dependency explicit
ata: pata_acpi: Make PCI dependency explicit
ACPI / LPSS: Make PCI dependency explicit
ARCv2 optimized memset uses PREFETCHW instruction for prefetching the
next cache line but doesn't ensure that the line is not past the end of
the buffer. PRETECHW changes the line ownership and marks it dirty,
which can cause issues in SMP config when next line was already owned by
other core. Fix the issue by avoiding the PREFETCHW
Some more details:
The current code has 3 logical loops (ignroing the unaligned part)
(a) Big loop for doing aligned 64 bytes per iteration with PREALLOC
(b) Loop for 32 x 2 bytes with PREFETCHW
(c) any left over bytes
loop (a) was already eliding the last 64 bytes, so PREALLOC was
safe. The fix was removing PREFETCW from (b).
Another potential issue (applicable to configs with 32 or 128 byte L1
cache line) is that PREALLOC assumes 64 byte cache line and may not do
the right thing specially for 32b. While it would be easy to adapt,
there are no known configs with those lie sizes, so for now, just
compile out PREALLOC in such cases.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Cc: stable@vger.kernel.org #4.4+
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
[vgupta: rewrote changelog, used asm .macro vs. "C" macro]
do_page_fault() forgot to relinquish mmap_sem if a signal came while
handling handle_mm_fault() - due to say a ctl+c or oom etc.
This would later cause a deadlock by acquiring it twice.
This came to light when running libc testsuite tst-tls3-malloc test but
is likely also the cause for prior seen LTP failures. Using lockdep
clearly showed what the issue was.
| # while true; do ./tst-tls3-malloc ; done
| Didn't expect signal from child: got `Segmentation fault'
| ^C
| ============================================
| WARNING: possible recursive locking detected
| 4.17.0+ #25 Not tainted
| --------------------------------------------
| tst-tls3-malloc/510 is trying to acquire lock:
| 606c7728 (&mm->mmap_sem){++++}, at: __might_fault+0x28/0x5c
|
|but task is already holding lock:
|606c7728 (&mm->mmap_sem){++++}, at: do_page_fault+0x9c/0x2a0
|
| other info that might help us debug this:
| Possible unsafe locking scenario:
|
| CPU0
| ----
| lock(&mm->mmap_sem);
| lock(&mm->mmap_sem);
|
| *** DEADLOCK ***
|
------------------------------------------------------------
What the change does is not obvious (note to myself)
prior code was
| do_page_fault
|
| down_read() <-- lock taken
| handle_mm_fault <-- signal pending as this runs
| if fatal_signal_pending
| if VM_FAULT_ERROR
| up_read
| if user_mode
| return <-- lock still held, this was the BUG
New code
| do_page_fault
|
| down_read() <-- lock taken
| handle_mm_fault <-- signal pending as this runs
| if fatal_signal_pending
| if VM_FAULT_RETRY
| return <-- not same case as above, but still OK since
| core mm already relinq lock for FAULT_RETRY
| ...
|
| < Now falls through for bug case above >
|
| up_read() <-- lock relinquished
Cc: stable@vger.kernel.org
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
While in the native case entry into the kernel happens on the trampoline
stack, PV Xen kernels get entered with the current thread stack right
away. Hence source and destination stacks are identical in that case,
and special care is needed.
Other than in sync_regs() the copying done on the INT80 path isn't
NMI / #MC safe, as either of these events occurring in the middle of the
stack copying would clobber data on the (source) stack.
There is similar code in interrupt_entry() and nmi(), but there is no fixup
required because those code paths are unreachable in XEN PV guests.
[ tglx: Sanitized subject, changelog, Fixes tag and stable mail address. Sigh ]
Fixes: 7f2590a110 ("x86/entry/64: Use a per-CPU trampoline stack for IDT entries")
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Juergen Gross <jgross@suse.com>
Acked-by: Andy Lutomirski <luto@kernel.org>
Cc: Peter Anvin <hpa@zytor.com>
Cc: xen-devel@lists.xenproject.org>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/5C3E1128020000780020DFAD@prv1-mh.provo.novell.com
signal handling core calls show_regs() with preemption disabled which
on ARC takes mmap_sem for mm/vma access, causing lockdep splat.
| [ARCLinux]# ./segv-null-ptr
| potentially unexpected fatal signal 11.
| BUG: sleeping function called from invalid context at kernel/fork.c:1011
| in_atomic(): 1, irqs_disabled(): 0, pid: 70, name: segv-null-ptr
| no locks held by segv-null-ptr/70.
| CPU: 0 PID: 70 Comm: segv-null-ptr Not tainted 4.18.0+ #69
|
| Stack Trace:
| arc_unwind_core+0xcc/0x100
| ___might_sleep+0x17a/0x190
| mmput+0x16/0xb8
| show_regs+0x52/0x310
| get_signal+0x5ee/0x610
| do_signal+0x2c/0x218
| resume_user_mode_begin+0x90/0xd8
Workaround by re-enabling preemption temporarily.
Note that the preemption disabling in core code around show_regs()
was introduced by commit 3a9f84d354 ("signals, debug: fix BUG: using
smp_processor_id() in preemptible code in print_fatal_signal()")
to silence a differnt lockdep seen on x86 bakc in 2009.
Cc: <stable@vger.kernel.org>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
and use smaller/on-stack buffer instead
The motivation for this change was lockdep splat like below.
| potentially unexpected fatal signal 11.
| BUG: sleeping function called from invalid context at ../mm/page_alloc.c:4317
| in_atomic(): 1, irqs_disabled(): 0, pid: 57, name: segv
| no locks held by segv/57.
| Preemption disabled at:
| [<8182f17e>] get_signal+0x4a6/0x7c4
| CPU: 0 PID: 57 Comm: segv Not tainted 4.17.0+ #23
|
| Stack Trace:
| arc_unwind_core.constprop.1+0xd0/0xf4
| __might_sleep+0x1f6/0x234
| __get_free_pages+0x174/0xca0
| show_regs+0x22/0x330
| get_signal+0x4ac/0x7c4 # print_fatal_signals() -> preempt_disable()
| do_signal+0x30/0x224
| resume_user_mode_begin+0x90/0xd8
So signal handling core calls show_regs() with preemption disabled but
an ensuing GFP_KERNEL page allocator call is flagged by lockdep.
We could have switched to GFP_NOWAIT, but turns out that is not enough
anways and eliding page allocator call leads to less code and
instruction traces to sift thru when debugging pesky crashes.
FWIW, this patch doesn't cure the lockdep splat (which next patch does).
Reviewed-by: William Kucharski <william.kucharski@oracle.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Export all available ARC architected hardware events as
kernel PMU events to make non-generic events accessible.
ARC PMU HW allow us to read the list of all available
events names. So we generate kernel PMU event list
dynamically in arc_pmu_device_probe() using
human-readable events names we got from HW instead of
using pre-defined events list.
-------------------------->8--------------------------
$ perf list
[snip]
arc_pmu/bdata64/ [Kernel PMU event]
arc_pmu/bdcstall/ [Kernel PMU event]
arc_pmu/bdslot/ [Kernel PMU event]
arc_pmu/bfbmp/ [Kernel PMU event]
arc_pmu/bfirqex/ [Kernel PMU event]
arc_pmu/bflgstal/ [Kernel PMU event]
arc_pmu/bflush/ [Kernel PMU event]
-------------------------->8--------------------------
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
* Use BIT(), lower_32_bits(), upper_32_bits() macroses,
fix code style violations.
* Use u32, u64, s64 instead of uint32_t, uint64_t, int64_t
* Fix description comment as this code doesn't belong only to
ARC700 anymore.
* Use SPDX License Identifier.
* Remove useless ifdefs. ifdef around 'arc_pmu_match' structure
declaration is useless as we refer to 'arc_pmu_match' in
several places which aren't guarded with ifdef. Nevertheless
'ARC' option selects 'OF' unconditionally so we can simply
get rid of this ifdef.
Acked-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
So far we've mapped branches to "ijmp" which also counts conditional
branches NOT taken. This makes us different from other architectures
such as ARM which seem to be counting only taken branches.
So use "ijmptak" hardware condition which only counts (all jump
instructions that are taken)
'ijmptak' event is available on both ARCompact and ARCv2 ISA based
cores.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Cc: stable@vger.kernel.org
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
[vgupta: reworked changelog]
In setup_arch_memory we reserve the memory area wherein the kernel
is located. Current implementation may reserve more memory than
it actually required in case of CONFIG_LINUX_LINK_BASE is not
equal to CONFIG_LINUX_RAM_BASE. This happens because we calculate
start of the reserved region relatively to the CONFIG_LINUX_RAM_BASE
and end of the region relatively to the CONFIG_LINUX_RAM_BASE.
For example in case of HSDK board we wasted 256MiB of physical memory:
------------------->8------------------------------
Memory: 770416K/1048576K available (5496K kernel code,
240K rwdata, 1064K rodata, 2200K init, 275K bss,
278160K reserved, 0K cma-reserved)
------------------->8------------------------------
Fix that.
Fixes: 9ed68785f7 ("ARC: mm: Decouple RAM base address from kernel link addr")
Cc: stable@vger.kernel.org #4.14+
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
This commit removes redundant generic-y defines in
arch/arc/include/asm/Kbuild.
It is redundant to define generic-y when arch-specific implementation
exists in arch/$(ARCH)/include/asm/*.h
Remove the following generic-y:
dma-mapping.h
fb.h
kmap_types.h
pci.h
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
