Saeed Mahameed says:
====================
mlx5-updates-2018-03-30
This series contains updates to mlx5 core and mlx5e netdev drivers.
The main highlight of this series is the RX optimizations for striding RQ path,
introduced by Tariq.
First Four patches are trivial misc cleanups.
- Spelling mistake fix
- Dead code removal
- Warning messages
RX optimizations for striding RQ:
1) RX refactoring, cleanups and micro optimizations
- MTU calculation simplifications, obsoletes some WQEs-to-packets translation
functions and helps delete ~60 LOC.
- Do not busy-wait a pending UMR completion.
- post the new values of UMR WQE inline, instead of using a data pointer.
- use pre-initialized structures to save calculations in datapath.
2) Use linear SKB in Striding RQ "build_skb", (Using linear SKB has many advantages):
- Saves a memcpy of the headers.
- No page-boundary checks in datapath.
- No filler CQEs.
- Significantly smaller CQ.
- SKB data continuously resides in linear part, and not split to
small amount (linear part) and large amount (fragment).
This saves datapath cycles in driver and improves utilization
of SKB fragments in GRO.
- The fragments of a resulting GRO SKB follow the IP forwarding
assumption of equal-size fragments.
implementation details:
HW writes the packets to the beginning of a stride,
i.e. does not keep headroom. To overcome this we make sure we can
extend backwards and use the last bytes of stride i-1.
Extra care is needed for stride 0 as it has no preceding stride.
We make sure headroom bytes are available by shifting the buffer
pointer passed to HW by headroom bytes.
This configuration now becomes default, whenever capable.
Of course, this implies turning LRO off.
Performance testing:
ConnectX-5, single core, single RX ring, default MTU.
UDP packet rate, early drop in TC layer:
--------------------------------------------
| pkt size | before | after | ratio |
--------------------------------------------
| 1500byte | 4.65 Mpps | 5.96 Mpps | 1.28x |
| 500byte | 5.23 Mpps | 5.97 Mpps | 1.14x |
| 64byte | 5.94 Mpps | 5.96 Mpps | 1.00x |
--------------------------------------------
TCP streams: ~20% gain
3) Support XDP over Striding RQ:
Now that linear SKB is supported over Striding RQ,
we can support XDP by setting stride size to PAGE_SIZE
and headroom to XDP_PACKET_HEADROOM.
Striding RQ is capable of a higher packet-rate than
conventional RQ.
Performance testing:
ConnectX-5, 24 rings, default MTU.
CQE compression ON (to reduce completions BW in PCI).
XDP_DROP packet rate:
--------------------------------------------------
| pkt size | XDP rate | 100GbE linerate | pct% |
--------------------------------------------------
| 64byte | 126.2 Mpps | 148.0 Mpps | 85% |
| 128byte | 80.0 Mpps | 84.8 Mpps | 94% |
| 256byte | 42.7 Mpps | 42.7 Mpps | 100% |
| 512byte | 23.4 Mpps | 23.4 Mpps | 100% |
--------------------------------------------------
4) Remove mlx5 page_ref bulking in Striding RQ and use page_ref_inc only when needed.
Without this bulking, we have:
- no atomic ops on WQE allocation or free
- one atomic op per SKB
- In the default MTU configuration (1500, stride size is 2K),
the non-bulking method execute 2 atomic ops as before
- For larger MTUs with stride size of 4K, non-bulking method
executes only a single op.
- For XDP (stride size of 4K, no SKBs), non-bulking have no atomic ops per packet at all.
Performance testing:
ConnectX-5, Intel(R) Xeon(R) CPU E5-2680 v3 @ 2.50GHz.
Single core packet rate (64 bytes).
Early drop in TC: no degradation.
XDP_DROP:
before: 14,270,188 pps
after: 20,503,603 pps, 43% improvement.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
David Howells says:
====================
rxrpc: Fixes and more traces
Here are some patches that add some more tracepoints to AF_RXRPC and fix
some issues therein:
(1) Fix the use of VERSION packets to keep firewall routes open.
(2) Fix the incorrect current time usage in a tracepoint.
(3) Fix Tx ring annotation corruption.
(4) Fix accidental conversion of call-level abort into connection-level
abort.
(5) Fix calculation of resend time.
(6) Remove a couple of unused variables.
(7) Fix a bunch of checker warnings and an error. Note that not all
warnings can be quashed as checker doesn't seem to correctly handle
seqlocks.
(8) Fix a potential race between call destruction and socket/net
destruction.
(9) Add a tracepoint to track rxrpc_local refcounting.
(10) Fix an apparent leak of rxrpc_local objects.
(11) Add a tracepoint to track rxrpc_peer refcounting.
(12) Fix a leak of rxrpc_peer objects.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
gcc points out that the combined length of the fixed-length inputs to
l->name is larger than the destination buffer size:
net/tipc/link.c: In function 'tipc_link_create':
net/tipc/link.c:465:26: error: '%s' directive writing up to 32 bytes
into a region of size between 26 and 58 [-Werror=format-overflow=]
sprintf(l->name, "%s:%s-%s:unknown", self_str, if_name, peer_str);
net/tipc/link.c:465:2: note: 'sprintf' output 11 or more bytes
(assuming 75) into a destination of size 60
sprintf(l->name, "%s:%s-%s:unknown", self_str, if_name, peer_str);
A detailed analysis reveals that the theoretical maximum length of
a link name is:
max self_str + 1 + max if_name + 1 + max peer_str + 1 + max if_name =
16 + 1 + 15 + 1 + 16 + 1 + 15 = 65
Since we also need space for a trailing zero we now set MAX_LINK_NAME
to 68.
Just to be on the safe side we also replace the sprintf() call with
snprintf().
Fixes: 25b0b9c4e8 ("tipc: handle collisions of 32-bit node address
hash values")
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The three address type structs in the user API have names that in
reality reflect the specific, non-Linux environment where they were
originally created.
We now give them more intuitive names, in accordance with how TIPC is
described in the current documentation.
struct tipc_portid -> struct tipc_socket_addr
struct tipc_name -> struct tipc_service_addr
struct tipc_name_seq -> struct tipc_service_range
To avoid confusion, we also update some commmets and macro names to
match the new terminology.
For compatibility, we add macros that map all old names to the new ones.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current Striding RQ HW feature utilizes the RX buffers so that
there is no wasted room between the strides. This maximises
the memory utilization.
This prevents the use of build_skb() (which requires headroom
and tailroom), and demands to memcpy the packets headers into
the skb linear part.
In this patch, whenever a set of conditions holds, we apply
an RQ configuration that allows combining the use of linear SKB
on top of a Striding RQ.
To use build_skb() with Striding RQ, the following must hold:
1. packet does not cross a page boundary.
2. there is enough headroom and tailroom surrounding the packet.
We can satisfy 1 and 2 by configuring:
stride size = MTU + headroom + tailoom.
This is possible only when:
a. (MTU - headroom - tailoom) does not exceed PAGE_SIZE.
b. HW LRO is turned off.
Using linear SKB has many advantages:
- Saves a memcpy of the headers.
- No page-boundary checks in datapath.
- No filler CQEs.
- Significantly smaller CQ.
- SKB data continuously resides in linear part, and not split to
small amount (linear part) and large amount (fragment).
This saves datapath cycles in driver and improves utilization
of SKB fragments in GRO.
- The fragments of a resulting GRO SKB follow the IP forwarding
assumption of equal-size fragments.
Some implementation details:
HW writes the packets to the beginning of a stride,
i.e. does not keep headroom. To overcome this we make sure we can
extend backwards and use the last bytes of stride i-1.
Extra care is needed for stride 0 as it has no preceding stride.
We make sure headroom bytes are available by shifting the buffer
pointer passed to HW by headroom bytes.
This configuration now becomes default, whenever capable.
Of course, this implies turning LRO off.
Performance testing:
ConnectX-5, single core, single RX ring, default MTU.
UDP packet rate, early drop in TC layer:
--------------------------------------------
| pkt size | before | after | ratio |
--------------------------------------------
| 1500byte | 4.65 Mpps | 5.96 Mpps | 1.28x |
| 500byte | 5.23 Mpps | 5.97 Mpps | 1.14x |
| 64byte | 5.94 Mpps | 5.96 Mpps | 1.00x |
--------------------------------------------
TCP streams: ~20% gain
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
1. This function is not used anywhere in mlx5 driver
2. It has a memcpy statement that makes no sense and produces build
warning with gcc8
drivers/net/ethernet/mellanox/mlx5/core/transobj.c: In function 'mlx5_core_query_xsrq':
drivers/net/ethernet/mellanox/mlx5/core/transobj.c:347:3: error: 'memcpy' source argument is the same as destination [-Werror=restrict]
Fixes: 01949d0109 ("net/mlx5_core: Enable XRCs and SRQs when using ISSI > 0")
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Pablo Neira Ayuso says:
====================
Netfilter/IPVS updates for net-next
The following patchset contains Netfilter/IPVS updates for your net-next
tree. This batch comes with more input sanitization for xtables to
address bug reports from fuzzers, preparation works to the flowtable
infrastructure and assorted updates. In no particular order, they are:
1) Make sure userspace provides a valid standard target verdict, from
Florian Westphal.
2) Sanitize error target size, also from Florian.
3) Validate that last rule in basechain matches underflow/policy since
userspace assumes this when decoding the ruleset blob that comes
from the kernel, from Florian.
4) Consolidate hook entry checks through xt_check_table_hooks(),
patch from Florian.
5) Cap ruleset allocations at 512 mbytes, 134217728 rules and reject
very large compat offset arrays, so we have a reasonable upper limit
and fuzzers don't exercise the oom-killer. Patches from Florian.
6) Several WARN_ON checks on xtables mutex helper, from Florian.
7) xt_rateest now has a hashtable per net, from Cong Wang.
8) Consolidate counter allocation in xt_counters_alloc(), from Florian.
9) Earlier xt_table_unlock() call in {ip,ip6,arp,eb}tables, patch
from Xin Long.
10) Set FLOW_OFFLOAD_DIR_* to IP_CT_DIR_* definitions, patch from
Felix Fietkau.
11) Consolidate code through flow_offload_fill_dir(), also from Felix.
12) Inline ip6_dst_mtu_forward() just like ip_dst_mtu_maybe_forward()
to remove a dependency with flowtable and ipv6.ko, from Felix.
13) Cache mtu size in flow_offload_tuple object, this is safe for
forwarding as f87c10a8aa describes, from Felix.
14) Rename nf_flow_table.c to nf_flow_table_core.o, to simplify too
modular infrastructure, from Felix.
15) Add rt0, rt2 and rt4 IPv6 routing extension support, patch from
Ahmed Abdelsalam.
16) Remove unused parameter in nf_conncount_count(), from Yi-Hung Wei.
17) Support for counting only to nf_conncount infrastructure, patch
from Yi-Hung Wei.
18) Add strict NFT_CT_{SRC_IP,DST_IP,SRC_IP6,DST_IP6} key datatypes
to nft_ct.
19) Use boolean as return value from ipt_ah and from IPVS too, patch
from Gustavo A. R. Silva.
20) Remove useless parameters in nfnl_acct_overquota() and
nf_conntrack_broadcast_help(), from Taehee Yoo.
21) Use ipv6_addr_is_multicast() from xt_cluster, also from Taehee Yoo.
22) Statify nf_tables_obj_lookup_byhandle, patch from Fengguang Wu.
23) Fix typo in xt_limit, from Geert Uytterhoeven.
24) Do no use VLAs in Netfilter code, again from Gustavo.
25) Use ADD_COUNTER from ebtables, from Taehee Yoo.
26) Bitshift support for CONNMARK and MARK targets, from Jack Ma.
27) Use pr_*() and add pr_fmt(), from Arushi Singhal.
28) Add synproxy support to ctnetlink.
29) ICMP type and IGMP matching support for ebtables, patches from
Matthias Schiffer.
30) Support for the revision infrastructure to ebtables, from
Bernie Harris.
31) String match support for ebtables, also from Bernie.
32) Documentation for the new flowtable infrastructure.
33) Use generic comparison functions in ebt_stp, from Joe Perches.
34) Demodularize filter chains in nftables.
35) Register conntrack hooks in case nftables NAT chain is added.
36) Merge assignments with return in a couple of spots in the
Netfilter codebase, also from Arushi.
37) Document that xtables percpu counters are stored in the same
memory area, from Ben Hutchings.
38) Revert mark_source_chains() sanity checks that break existing
rulesets, from Florian Westphal.
39) Use is_zero_ether_addr() in the ipset codebase, from Joe Perches.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, driver registers it from pernet_operations::init method,
and this breaks modularity, because initialization of net namespace
and netdevice notifiers are orthogonal actions. We don't have
per-namespace netdevice notifiers; all of them are global for all
devices in all namespaces.
Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's common practice to store MAC addresses for network interfaces into
nvmem devices. However the code to actually do this in the kernel lacks,
so this patch adds of_get_nvmem_mac_address() for drivers to obtain the
address from an nvmem cell provider.
This is particulary useful on devices where the ethernet interface cannot
be configured by the bootloader, for example because it's in an FPGA.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for having DSA transition entirely to PHYLINK, we need to pass a
PHY interface type to the mac_link_{up,down} callbacks because we may have to
make decisions on that (e.g: turn on/off RGMII interfaces etc.). We do not pass
an entire phylink_link_state because not all parameters (pause, duplex etc.) are
defined when the link is down, only link and interface are.
Update mvneta accordingly since it currently implements phylink_mac_ops.
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NETIF_F_HW_VLAN_[CS]TAG_FILTER features require more than just a bit
flip in dev->features in order to keep the driver in a consistent state.
These features notify the driver of each added/removed vlan, but toggling
of vlan-filter does not notify the driver accordingly for each of the
existing vlans.
This patch implements a similar solution to NETIF_F_RX_UDP_TUNNEL_PORT
behavior (which notifies the driver about UDP ports in the same manner
that vids are reported).
Each toggling of the features propagates to the 8021q module, which
iterates over the vlans and call add/kill ndo accordingly.
Signed-off-by: Gal Pressman <galp@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Register conntrack hooks if the user adds NAT chains. Users get confused
with the existing behaviour since they will see no packets hitting this
chain until they add the first rule that refers to conntrack.
This patch adds new ->init() and ->free() indirections to chain types
that can be used by NAT chains to invoke the conntrack dependency.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
One module per supported filter chain family type takes too much memory
for very little code - too much modularization - place all chain filter
definitions in one single file.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Use WARN_ON() instead since it should not happen that neither family
goes over NFPROTO_NUMPROTO nor there is already a chain of this type
already registered.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Use nft_ prefix. By when I added chain types, I forgot to use the
nftables prefix. Rename enum nft_chain_type to enum nft_chain_types too,
otherwise there is an overlap.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Currently ebtables assumes that the revision number of all match
modules is 0, which is an issue when trying to use existing
xtables matches with ebtables. The solution is to modify ebtables
to allow extensions to specify a revision number, similar to
iptables. This gets passed down to the kernel, which is then able
to find the match module correctly.
To main binary backwards compatibility, the size of the ebt_entry
structures is not changed, only the size of the name field is
decreased by 1 byte to make room for the revision field.
Signed-off-by: Bernie Harris <bernie.harris@alliedtelesis.co.nz>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Johannes Berg says:
====================
We have a fair number of patches, but many of them are from the
first bullet here:
* EAPoL-over-nl80211 from Denis - this will let us fix
some long-standing issues with bridging, races with
encryption and more
* DFS offload support from the qtnfmac folks
* regulatory database changes for the new ETSI adaptivity
requirements
* various other fixes and small enhancements
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the required driver support for updating the flash or
non volatile memory of the adapter. At highlevel, flash upgrade comprises
of reading the flash images from the input file, validating the images and
writing them to the respective paritions.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This FW contains several fixes and features
RDMA Features
- SRQ support
- XRC support
- Memory window support
- RDMA low latency queue support
- RDMA bonding support
RDMA bug fixes
- RDMA remote invalidate during retransmit fix
- iWARP MPA connect interop issue with RTR fix
- iWARP Legacy DPM support
- Fix MPA reject flow
- iWARP error handling
- RQ WQE validation checks
MISC
- Fix some HSI types endianity
- New Restriction: vlan insertion in core_tx_bd_data can't be set
for LB packets
ETH
- HW QoS offload support
- Fix vlan, dcb and sriov flow of VF sending a packet with
inband VLAN tag instead of default VLAN
- Allow GRE version 1 offloads in RX flow
- Allow VXLAN steering
iSCSI / FcoE
- Fix bd availability checking flow
- Support 256th sge proerly in iscsi/fcoe retransmit
- Performance improvement
- Fix handle iSCSI command arrival with AHS and with immediate
- Fix ipv6 traffic class configuration
DEBUG
- Update debug utilities
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: Manish Rangankar <Manish.Rangankar@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Acked-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Saeed Mahameed says:
====================
mlx5-updates-2018-03-27 (Misc updates & SQ recovery)
This series contains Misc updates and cleanups for mlx5e rx path
and SQ recovery feature for tx path.
From Tariq: (RX updates)
- Disable Striding RQ when PCI devices, striding RQ limits the use
of CQE compression feature, which is very critical for slow PCI
devices performance, in this change we will prefer CQE compression
over Striding RQ only on specific "slow" PCIe links.
- RX path cleanups
- Private flag to enable/disable striding RQ
From Eran: (TX fast recovery)
- TX timeout logic improvements, fast SQ recovery and TX error reporting
if a HW error occurs while transmitting on a specific SQ, the driver will
ignore such error and will wait for TX timeout to occur and reset all
the rings. Instead, the current series improves the resiliency for such
HW errors by detecting TX completions with errors, which will report them
and perform a fast recover for the specific faulty SQ even before a TX
timeout is detected.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
rtnl_lock() is used everywhere, and contention is very high.
When someone wants to iterate over alive net namespaces,
he/she has no a possibility to do that without exclusive lock.
But the exclusive rtnl_lock() in such places is overkill,
and it just increases the contention. Yes, there is already
for_each_net_rcu() in kernel, but it requires rcu_read_lock(),
and this can't be sleepable. Also, sometimes it may be need
really prevent net_namespace_list growth, so for_each_net_rcu()
is not fit there.
This patch introduces new rw_semaphore, which will be used
instead of rtnl_mutex to protect net_namespace_list. It is
sleepable and allows not-exclusive iterations over net
namespaces list. It allows to stop using rtnl_lock()
in several places (what is made in next patches) and makes
less the time, we keep rtnl_mutex. Here we just add new lock,
while the explanation of we can remove rtnl_lock() there are
in next patches.
Fine grained locks generally are better, then one big lock,
so let's do that with net_namespace_list, while the situation
allows that.
Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit implements the TX side of NL80211_CMD_CONTROL_PORT_FRAME.
Userspace provides the raw EAPoL frame using NL80211_ATTR_FRAME.
Userspace should also provide the destination address and the protocol
type to use when sending the frame. This is used to implement TX of
Pre-authentication frames. If CONTROL_PORT_ETHERTYPE_NO_ENCRYPT is
specified, then the driver will be asked not to encrypt the outgoing
frame.
A new EXT_FEATURE flag is introduced so that nl80211 code can check
whether a given wiphy has capability to pass EAPoL frames over nl80211.
Signed-off-by: Denis Kenzior <denkenz@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This commit also adds cfg80211_rx_control_port function. This is used
to generate a CMD_CONTROL_PORT_FRAME event out to userspace. The
conn_owner_nlportid is used as the unicast destination. This means that
userspace must specify NL80211_ATTR_SOCKET_OWNER flag if control port
over nl80211 routing is requested in NL80211_CMD_CONNECT,
NL80211_CMD_ASSOCIATE, NL80211_CMD_START_AP or IBSS/mesh join.
Signed-off-by: Denis Kenzior <denkenz@gmail.com>
[johannes: fix return value of cfg80211_rx_control_port()]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In general regulatory self managed devices maintain their own
regulatory profiles thus it doesn't have to query the regulatory database
on country change.
ETSI has recently introduced a new channel access mechanism for 5GHz
that all wlan devices need to comply with.
These values are stored in the regulatory database.
There are self managed devices which can't maintain these
values on their own. Add API to allow self managed regulatory devices
to query the regulatory database for high band wmm rule.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
[johannes: fix documentation]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
ETSI EN 301 893 v2.1.1 (2017-05) standard defines a new channel access
mechanism that all devices (WLAN and LAA) need to comply with.
The regulatory database can now be loaded into the kernel and also
has the option to load optional data.
In order to be able to comply with ETSI standard, we add wmm_rule into
regulatory rule and add the option to read its value from the regulatory
database.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
[johannes: fix memory leak in error path]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Denis Kenzior <denkenz@gmail.com>
[johannes: fix race with wdev lock/unlock by just acquiring once]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Denis Kenzior <denkenz@gmail.com>
[johannes: fix race with wdev lock/unlock by just acquiring once]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently bw and smps_mode are u8 type value in sta_opmode_info
structure. This values filled in mac80211 from ieee80211_sta_rx_bandwidth
and ieee80211_smps_mode. These enum values are specific to mac80211 and
userspace/cfg80211 doesn't know about that. This will lead to incorrect
result/assumption by the user space application.
Change bw and smps_mode parameters to their respective enums in nl80211.
Signed-off-by: Tamizh chelvam <tamizhr@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Move mlx5_ib dump error CQE implementation to mlx5 CQ header file in
order to use it in a downstream patch from mlx5e.
In addition, use print_hex_dump instead of manual dumping of the buffer.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Move query SQ state function from mlx5_ib to mlx5_core in order to
have it in shared code.
It will be used in a downstream patch from mlx5e.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Add a tracepoint to track rxrpc calls moving into the completed state and
to log the completion type and the recorded error value and abort code.
Signed-off-by: David Howells <dhowells@redhat.com>
In rxrpc and afs, use the debug_ids that are monotonically allocated to
various objects as they're allocated rather than pointers as kernel
pointers are now hashed making them less useful. Further, the debug ids
aren't reused anywhere nearly as quickly.
In addition, allow kernel services that use rxrpc, such as afs, to take
numbers from the rxrpc counter, assign them to their own call struct and
pass them in to rxrpc for both client and service calls so that the trace
lines for each will have the same ID tag.
Signed-off-by: David Howells <dhowells@redhat.com>
Add a tracepoint to trace packet resend events and to dump the Tx
annotation buffer for added illumination.
Signed-off-by: David Howells <dhowells@rdhat.com>
This adds comments to different places to improve
readability.
Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
net_sem is some undefined area name, so it will be better
to make the area more defined.
Rename it to pernet_ops_rwsem for better readability and
better intelligibility.
Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Synchronous pernet_operations are not allowed anymore.
All are asynchronous. So, drop the structure member.
Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Saeed Mahameed says:
====================
mlx5-updates-2018-03-22 (Misc updates)
This series includes misc updates for mlx5 core and netdev dirver,
Highlights:
From Inbar, three patches to add support for PFC stall prevention
statistics and enable/disable through new ethtool tunable, as requested
from previous submission.
From Moshe, four patches, added more drop counters:
- drop counter for netdev steering miss
- drop counter for when VF logical link is down
- drop counter for when netdev logical link is down.
From Or, three patches to support vlan push/pop offload via tc HW action,
for newer HW (Connectx-5 and onward) via HW steering flow actions rather
than the emulated path for the older HW brands.
And five more misc small trivial patches.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
After Commit dae399d7fd ("sctp: hold transport instead of assoc
when lookup assoc in rx path"), it put transport instead of asoc
in sctp_has_association. Variable 'asoc' is not used any more.
So this patch is to remove it, while at it, it also changes the
return type of sctp_has_association to bool, and does the same
for it's caller sctp_endpoint_is_peeled_off.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Newer NICs (ConnectX-5 and onward) can apply vlan pop or push as an
action taking place during flow steering. Add the core bits for that.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Added the following packets dropped while vport down statistics:
Rx dropped while vport down - counts packets which were steered by
e-switch to a vport, but dropped since the vport was down. This counter
will be shown on ip link tool as part of the vport rx_dropped counter.
Tx dropped while vport down - counts packets which were transmitted by
a vport, but dropped due to vport logical link down. This counter
will be shown on ip link tool as part of the vport tx_dropped counter.
The counters are read from FW by command QUERY_VNIC_ENV.
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Added the following packets drop counter:
Rx steering missed dropped packets - counts packets which were dropped
due to miss on NIC rx steering rules.
This counter will be shown on ethtool as a new counter called
rx_steer_missed_packets.
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Add support for new FW command QUERY_VNIC_ENV.
The command is used by the driver to query vnic diagnostic statistics
from FW.
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
