USP0 has multiple functions, and has RX and TX frame sync signals,
for some scenarios like audio PCM, we don't need both of them.
so here we add two possibilities for USP0 only holding one of TX
and RX frame sync.
commit 8385af02ba only added this group for prima2, and missed
atlas6. This patch fixes it.
Signed-off-by: Rongjun Ying <rongjun.ying@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
For some silicons, the pin configuration register can control
the output of the pin when the pad including the pin enter
low power mode.
For example, the pin can be "Drive 1", "Drive 0", "Float" when
the pad including the pin enter low power mode.
It is very useful when you want to control the power leakeage
when the SOC enter low power mode, and can save more power for
the low power mode.
Signed-off-by: Chao Xie <chao.xie@marvell.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When an IRQ is started on a GPIO line, mark this GPIO as IRQ in
the gpiolib so we can keep track of the usage centrally.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@traphandler.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
A QSPI function set consists of 3 groups:
- qspi_ctrl (2 control wires)
- qspi_data2 (2 data wires, for Single/Dual SPI)
- qspi_data4 (4 data wires, for Quad SPI)
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
ST pin controller does not have hardware support for detecting edge
triggered interrupts, It only has level triggering support.
This patch attempts to fake up edge triggers from hw level trigger
support in software. With this facility now the gpios can be easily used
for keypads, otherwise it would be difficult for drivers like keypads to
work with level trigger interrupts.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch add interrupt support to the pincontroller driver.
ST Pincontroller GPIO bank can have one of the two possible types of
interrupt-wirings.
First type is via irqmux, single interrupt is used by multiple gpio
banks. This reduces number of overall interrupts numbers required. All
these banks belong to a single pincontroller.
_________
| |----> [gpio-bank (n) ]
| |----> [gpio-bank (n + 1)]
[irqN]-- | irq-mux |----> [gpio-bank (n + 2)]
| |----> [gpio-bank (... )]
|_________|----> [gpio-bank (n + 7)]
Second type has a dedicated interrupt per gpio bank.
[irqN]----> [gpio-bank (n)]
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Pull vfs fixes from Al Viro:
"A couple of fixes, both -stable fodder. The O_SYNC bug is fairly
old..."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
fix a kmap leak in virtio_console
fix O_SYNC|O_APPEND syncing the wrong range on write()
While we are at it, don't do kmap() under kmap_atomic(), *especially*
for a page we'd allocated with GFP_KERNEL. It's spelled "page_address",
and had that been more than that, we'd have a real trouble - kmap_high()
can block, and doing that while holding kmap_atomic() is a Bad Idea(tm).
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Pull pinctrl fixes from Linus Walleij:
"First round of pin control fixes for v3.14:
- Protect pinctrl_list_add() with the proper mutex. This was
identified by RedHat. Caused nasty locking warnings was rootcased
by Stanislaw Gruszka.
- Avoid adding dangerous debugfs files when either half of the
subsystem is unused: pinmux or pinconf.
- Various fixes to various drivers: locking, hardware particulars, DT
parsing, error codes"
* tag 'pinctrl-v3.14-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: tegra: return correct error type
pinctrl: do not init debugfs entries for unimplemented functionalities
pinctrl: protect pinctrl_list add
pinctrl: sirf: correct the pin index of ac97_pins group
pinctrl: imx27: fix offset calculation in imx_read_2bit
pinctrl: vt8500: Change devicetree data parsing
pinctrl: imx27: fix wrong offset to ICONFB
pinctrl: at91: use locked variant of irq_set_handler
On archs like S390 or um this driver cannot build nor work.
Make it depend on HAS_IOMEM to bypass build failures.
drivers/built-in.o: In function `dw_wdt_drv_probe':
drivers/watchdog/dw_wdt.c:302: undefined reference to `devm_ioremap_resource'
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Pull media fixes from Mauro Carvalho Chehab:
"A series of small fixes. Mostly driver ones. There is one core
regression fix on a patch that was meant to fix some race issues on
vb2, but that actually caused more harm than good. So, we're just
reverting it for now"
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
[media] adv7842: Composite free-run platfrom-data fix
[media] v4l2-dv-timings: fix GTF calculation
[media] hdpvr: Fix memory leak in debug
[media] af9035: add ID [2040:f900] Hauppauge WinTV-MiniStick 2
[media] mxl111sf: Fix compile when CONFIG_DVB_USB_MXL111SF is unset
[media] mxl111sf: Fix unintentional garbage stack read
[media] cx24117: use a valid dev pointer for dev_err printout
[media] cx24117: remove dead code in always 'false' if statement
[media] update Michael Krufky's email address
[media] vb2: Check if there are buffers before streamon
[media] Revert "[media] videobuf_vm_{open,close} race fixes"
[media] go7007-loader: fix usb_dev leak
[media] media: bt8xx: add missing put_device call
[media] exynos4-is: Compile in fimc-lite runtime PM callbacks conditionally
[media] exynos4-is: Compile in fimc runtime PM callbacks conditionally
[media] exynos4-is: Fix error paths in probe() for !pm_runtime_enabled()
[media] s5p-jpeg: Fix wrong NV12 format parameters
[media] s5k5baf: allow to handle arbitrary long i2c sequences
Pull hwmon fixes from Guenter Roeck:
"Fix PMBus driver problem with some multi-page voltage sensors and fix
da9055 interrupt initialization"
* tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (da9055) Remove use of regmap_irq_get_virq()
hwmon: (pmbus) Support per-page exponent in linear mode
Pull ACPI and power management fixes from Rafael Wysocki:
"These include a fix for a recent ACPI hotplug regression, four
concurrency related fixes and one PCI device removal fix for
ACPI-based PCI hotplug (ACPIPHP), intel_pstate fix that should go into
stable, three simple ACPI cleanups and a new entry for the ACPI video
blacklist.
Specifics:
- Fix for a recent ACPI hotplug regression causing a NULL pointer
dereference to occur while handling ACPI eject notifications for
already ejected devices. From Toshi Kani.
- Four concurrency-related fixes for ACPIPHP. Two of them add
missing locking and the other two fix race conditions related to
reference counting.
- ACPIPHP fix to avoid NULL pointer dereferences during device
removal involving Virtual Funcions.
- intel_pstate fix to make it compute the percentage of time the CPU
is busy properly. From Dirk Brandewie.
- Removal of two unnecessary NULL pointer checks in ACPI code and a
fix for sscanf() format string from Dan Carpenter and Luis G.F.
- New ACPI video blacklist entry for HP EliteBook Revolve 810 from
Mika Westerberg"
* tag 'pm+acpi-3.14-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI / hotplug: Fix panic on eject to ejected device
ACPI / battery: Fix incorrect sscanf() string in acpi_battery_init_alarm()
ACPI / proc: remove unneeded NULL check
ACPI / utils: remove a pointless NULL check
ACPI / video: Add HP EliteBook Revolve 810 to the blacklist
intel_pstate: Take core C0 time into account for core busy calculation
ACPI / hotplug / PCI: Fix bridge removal race vs dock events
ACPI / hotplug / PCI: Fix bridge removal race in handle_hotplug_event()
ACPI / hotplug / PCI: Scan root bus under the PCI rescan-remove lock
ACPI / hotplug / PCI: Move PCI rescan-remove locking to hotplug_event()
ACPI / hotplug / PCI: Remove entries from bus->devices in reverse order
Remove use of regmap_irq_get_virq() in driver probe which was
conflicting with use of platform_get_irq_byname().
platform_get_irq_byname() already returns the VIRQ number due
to MFD core translation so using regmap_irq_get_virq() on that
returned value results in an incorrect IRQ being requested.
The driver probes then fail because of this.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Pull drm fixes from Dave Airlie:
"A few regression fixes already, one for my own stupidity, and mgag200
typo fix, vmwgfx fixes and ttm regression fixes, and a radeon register
checker update for older cards to handle geom shaders"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/radeon: allow geom rings to be setup on r600/r700 (v2)
drm/mgag200,ast,cirrus: fix regression with drm_can_sleep conversion
drm/ttm: Don't clear page metadata of imported sg pages
drm/ttm: Fix TTM object open regression
vmwgfx: Fix unitialized stack read in vmw_setup_otable_base
drm/vmwgfx: Reemit context bindings when necessary v2
drm/vmwgfx: Detect old user-space drivers and set up legacy emulation v2
drm/vmwgfx: Emulate legacy shaders on guest-backed devices v2
drm/vmwgfx: Fix legacy surface reference size copyback
drm/vmwgfx: Fix SET_SHADER_CONST emulation on guest-backed devices
drm/vmwgfx: Fix regression caused by "drm/ttm: make ttm reservation calls behave like reservation calls"
drm/vmwgfx: Don't commit staged bindings if execbuf fails
drm/mgag200: fix typo causing bw limits to be ignored on some chips
Commit c420619 "pinctrl: pinconf: remove checks on ops->pin_config_get"
removed the check on (ops != NULL) when performing pinconf_pins_show() or
pinconf_groups_show(). As these entries are always enabled, even if
pinconf is not supported, reading will result in an oops due to NULL
ops.
Instead of checking for ops, remove the corresponding debugfs entries if
pinconf and/or pinmux are not implemented.
Tested on OMAP3 (pinctrl-single).
Cc: stable@vger.kernel.org
Signed-off-by: Florian Vaussard <florian.vaussard@epfl.ch>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
the evergreen CS parser has allowed this for a while, just port
the code to the r600 one.
This is required before geom shaders can be made work.
v2: agd5f: minor cleanup and add additional 7xx reg.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
A couple of vmwgfx fixes together with missing bits of legacy device
emulation to facilitate old user-space drivers on new devices.
The shader emulation bits are a bit large, but since they mostly touch the
new device code, regressions are unlikely. I figure the gain of having
this from the start clearly outweighs the risc of adding these bits at
this point.
Pull request of 2014-02-05
* tag 'vmwgfx-fixes-3.14-2014-02-05' of git://people.freedesktop.org/~thomash/linux:
vmwgfx: Fix unitialized stack read in vmw_setup_otable_base
drm/vmwgfx: Reemit context bindings when necessary v2
drm/vmwgfx: Detect old user-space drivers and set up legacy emulation v2
drm/vmwgfx: Emulate legacy shaders on guest-backed devices v2
drm/vmwgfx: Fix legacy surface reference size copyback
drm/vmwgfx: Fix SET_SHADER_CONST emulation on guest-backed devices
drm/vmwgfx: Fix regression caused by "drm/ttm: make ttm reservation calls behave like reservation calls"
drm/vmwgfx: Don't commit staged bindings if execbuf fails
Two ttm regression fixes.
Pull request of 2014-02-05
* tag 'ttm-fixes-3.14-2014-02-05' of git://people.freedesktop.org/~thomash/linux:
drm/ttm: Don't clear page metadata of imported sg pages
drm/ttm: Fix TTM object open regression
Pull irq updates from Thomas Gleixner:
"This lot provides:
* Bugfixes for armada irq controller
* Updates to renesas irq chip
* Support for the TI-NSPIRE irq controller
Not strictly a bug fix only pull request, but important updates for
some of the arm Socs which I completely forgot to send last week.
Seems like my obliviousness is getting worse, I just can't remember
when it started"
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip: Add support for TI-NSPIRE irqchip
irqchip: renesas-irqc: Enable mask on suspend
irqchip: renesas-irqc: Use lazy disable
irqchip: armada-370-xp: fix MSI race condition
irqchip: armada-370-xp: fix IPI race condition
Pull Xen fixes from Konrad Rzeszutek Wilk:
"Bug-fixes:
- Revert "xen/grant-table: Avoid m2p_override during mapping" as it
broke Xen ARM build.
- Fix CR4 not being set on AP processors in Xen PVH mode"
* tag 'stable/for-linus-3.14-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen/pvh: set CR4 flags for APs
Revert "xen/grant-table: Avoid m2p_override during mapping"
Pull NVMe driver update from Matthew Wilcox:
"Looks like I missed the merge window ... but these are almost all
bugfixes anyway (the ones that aren't have been baking for months)"
* git://git.infradead.org/users/willy/linux-nvme:
NVMe: Namespace use after free on surprise removal
NVMe: Correct uses of INIT_WORK
NVMe: Include device and queue numbers in interrupt name
NVMe: Add a pci_driver shutdown method
NVMe: Disable admin queue on init failure
NVMe: Dynamically allocate partition numbers
NVMe: Async IO queue deletion
NVMe: Surprise removal handling
NVMe: Abort timed out commands
NVMe: Schedule reset for failed controllers
NVMe: Device resume error handling
NVMe: Cache dev->pci_dev in a local pointer
NVMe: Fix lockdep warnings
NVMe: compat SG_IO ioctl
NVMe: remove deprecated IRQF_DISABLED
NVMe: Avoid shift operation when writing cq head doorbell
These page pointers shouldn't be visible to TTM in the first place, but
until we fix that up, don't clear the page metadata because that
will upset the exporter.
Reported-and-tested-by: Cristoph Haag <haagch.christoph@googleemail.com>
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Jakob Bornecrantz <jakob@vmware.com>
When an eject request is sent to an ejected ACPI device, the following
panic occurs:
ACPI: \_SB_.SCK3.CPU3: ACPI_NOTIFY_EJECT_REQUEST event
BUG: unable to handle kernel NULL pointer dereference at 0000000000000070
IP: [<ffffffff813a7cfe>] acpi_device_hotplug+0x10b/0x33b
:
Call Trace:
[<ffffffff813a24da>] acpi_hotplug_work_fn+0x1c/0x27
[<ffffffff8109cbe5>] process_one_work+0x175/0x430
[<ffffffff8109d7db>] worker_thread+0x11b/0x3a0
This is becase device->handler is NULL in acpi_device_hotplug().
This case was used to fail in acpi_hotplug_notify_cb() as the target
had no acpi_deivce. However, acpi_device now exists after ejection.
Added a check to verify if acpi_device->handler is valid for an
eject request in acpi_hotplug_notify_cb(). Note that handler passed
from an argument is still valid while acpi_device->handler is NULL.
Fixes: 202317a573 (ACPI / scan: Add acpi_device objects for all device nodes in the namespace)
Signed-off-by: Toshi Kani <toshi.kani@hp.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Commit drm/ttm: ttm object security fixes for render nodes introduced a
regression where, if a TTM object was opened multiple times from the same
open file, the caller would spin uninterruptibly in the kernel.
Fix this.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Jakob Bornecrantz <jakob@vmware.com>
One of the error paths in vmw_setup_otable_base causes us to return with
'ret' having never been set to anything causing us to return whatever was
on the stack.
Found with Coverity
Signed-off-by: Dave Jones <davej@fedoraproject.org>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
When a context is first referenced in the command stream, make sure that all
scrubbed (as a result of eviction) bindings are re-emitted. Also make sure that
all bound resources are put on the resource validate list.
This is needed for legacy emulation, since legacy user-space drivers will
typically not re-emit shader bindings. It also removes the requirement for
user-space drivers to re-emit render-target- and texture bindings.
Makes suspend and hibernate now also work with legacy user-space drivers on
guest-backed devices.
v2: Don't rebind on legacy devices.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Jakob Bornecrantz <jakob@vmware.com>
GB aware mesa userspace drivers are detected by the fact that they are
calling the vmw getparam ioctl querying DRM_VMW_PARAM_HW_CAPS to detect
whether the device is Guest-backed object capable. For other drivers,
lie about hardware version and send the 3D capabilities in a format they
expect.
v2:
Use DRM_VMW_PARAM_MAX_MOB_MEMORY to detect gb awareness,
Make sure we don't ovwerwrite bounce buffer or write past user-space buffer
indicated size.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Jakob Bornecrantz <jakob@vmware.com>
Command stream legacy shader creation and destruction is replaced by
NOPs in the command stream, and instead guest-backed shaders are created
and destroyed as part of the command validation process.
v2: Removed some stray debug messages.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Jakob Bornecrantz <jakob@vmware.com>
Surfaces created using the guest-backed surface interface only keeps the
base mip size, so only copy that if the legacy surface reference
ioctl requests the size information.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Jakob Bornecrantz <jakob@vmware.com>
Emulate the SET_SHADER_CONST legacy command on guest-backed devices by
issuing a SET_GB_SHADERCONSTS_INLINE command.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Jakob Bornecrantz <jakob@vmware.com>
If execbuf fails and binding commands are never sent to the device,
don't commit the staged context bindings to the tracker.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Jakob Bornecrantz <jakob@vmware.com>
Fix incorrect sscanf() string in acpi_battery_init_alarm().
Change from %ld to %lu, because 'x' is unsigned long.
Signed-off-by: Luis G.F <luisgf@luisgf.es>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
We already verified that "ldev" was non-NULL earlier and also we
dereference again without checking a three lines later.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
On HP EliteBook Revolve 810 the ACPI backlight device doesn't work as
expected. For example when resuming from system sleep, it seems to lose
backlight settings.
Forcing Intel driver fixes the problem so add this machine the ACPI
video detect blacklist.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
