netlink_getname(), netlink_sendmsg() and netlink_getsockbyportid()
can read nlk->dst_portid and nlk->dst_group while another
thread is changing them.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
On H3 ES1.x two bits in DPLLCR are used to select the DU input dot clock
source. These are bits 20 and 21 for DU2, and bits 22 and 23 for DU1. On
non-ES1.x, only the higher bits are used (bits 21 and 23), and the lower
bits are reserved and should be set to 0.
The current code always sets the lower bits, even on non-ES1.x.
For both DU1 and DU2, on all SoC versions, when writing zeroes to those
bits the input clock is DCLKIN, and thus there's no difference between
ES1.x and non-ES1.x.
For DU1, writing 0b10 to the bits (or only writing the higher bit)
results in using PLL0 as the input clock, so in this case there's also
no difference between ES1.x and non-ES1.x.
However, for DU2, writing 0b10 to the bits results in using PLL0 as the
input clock on ES1.x, whereas on non-ES1.x it results in using PLL1. On
ES1.x you need to write 0b11 to select PLL1.
The current code always writes 0b11 to PLCS0 field to select PLL1 on all
SoC versions, which works but causes an illegal (in the sense of not
allowed by the documentation) write to a reserved bit field.
To remove the illegal bit write on PLSC0 we need to handle the input dot
clock selection differently for ES1.x and non-ES1.x.
Add a new quirk, RCAR_DU_QUIRK_H3_ES1_PLL, for this. This way we can
always set the bit 21 on PLSC0 when choosing the PLL as the source
clock, and additionally set the bit 20 when on ES1.x.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
rcar_du_crtc.c does a soc_device_match() in
rcar_du_crtc_set_display_timing() to find out if the SoC is H3 ES1.x, and
if so, apply a workaround.
We will need another H3 ES1.x check in the following patch, so rather than
adding more soc_device_match() calls, let's add a rcar_du_device_info
entry for the ES1, and a quirk flag,
RCAR_DU_QUIRK_H3_ES1_PCLK_STABILITY, for the workaround.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Skip interference with an ongoing transaction, do not perform garbage
collection on inactive elements. Reset annotated previous end interval
if the expired element is marked as busy (control plane removed the
element right before expiration).
Fixes: 8d8540c4f5 ("netfilter: nft_set_rbtree: add timeout support")
Reviewed-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
...instead of a tree descent, which became overly complicated in an
attempt to cover cases where expired or inactive elements would affect
comparisons with the new element being inserted.
Further, it turned out that it's probably impossible to cover all those
cases, as inactive nodes might entirely hide subtrees consisting of a
complete interval plus a node that makes the current insertion not
overlap.
To speed up the overlap check, descent the tree to find a greater
element that is closer to the key value to insert. Then walk down the
node list for overlap detection. Starting the overlap check from
rb_first() unconditionally is slow, it takes 10 times longer due to the
full linear traversal of the list.
Moreover, perform garbage collection of expired elements when walking
down the node list to avoid bogus overlap reports.
For the insertion operation itself, this essentially reverts back to the
implementation before commit 7c84d41416 ("netfilter: nft_set_rbtree:
Detect partial overlaps on insertion"), except that cases of complete
overlap are already handled in the overlap detection phase itself, which
slightly simplifies the loop to find the insertion point.
Based on initial patch from Stefano Brivio, including text from the
original patch description too.
Fixes: 7c84d41416 ("netfilter: nft_set_rbtree: Detect partial overlaps on insertion")
Reviewed-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The Asus U46E backlight tables have a set of interesting problems:
1. Its ACPI tables do make _OSI ("Windows 2012") checks, so
acpi_osi_is_win8() should return true.
But the tables have 2 sets of _OSI calls, one from the usual global
_INI method setting a global OSYS variable and a second set of _OSI
calls from a MSOS method and the MSOS method is the only one calling
_OSI ("Windows 2012").
The MSOS method only gets called in the following cases:
1. From some Asus specific WMI methods
2. From _DOD, which only runs after acpi_video_get_backlight_type()
has already been called by the i915 driver
3. From other ACPI video bus methods which never run (see below)
4. From some EC query callbacks
So when i915 calls acpi_video_get_backlight_type() MSOS has never run
and acpi_osi_is_win8() returns false, so acpi_video_get_backlight_type()
returns acpi_video as the desired backlight type, which causes
the intel_backlight device to not register.
2. _DOD effectively does this:
Return (Package (0x01)
{
0x0400
})
causing acpi_video_device_in_dod() to return false, which causes
the acpi_video backlight device to not register.
Leaving the user with no backlight device at all. Note that before 6.1.y
the i915 driver would register the intel_backlight device unconditionally
and since that then was the only backlight device userspace would use that.
Add a backlight=native DMI quirk for this special laptop to restore
the old (and working) behavior of the intel_backlight device registering.
Fixes: fb1836c913 ("ACPI: video: Prefer native over vendor")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The HP EliteBook 8460p predates Windows 8, so it defaults to using
acpi_video# for backlight control.
Starting with the 6.1.y kernels the native radeon_bl0 backlight is hidden
in this case instead of relying on userspace preferring acpi_video# over
native backlight devices.
It turns out that for the acpi_video# interface to work on
the HP EliteBook 8460p, the brightness needs to be set at least once
through the native interface, which now no longer is done breaking
backlight control.
The native interface however always works without problems, so add
a quirk to use native backlight on the EliteBook 8460p to fix this.
Fixes: fb1836c913 ("ACPI: video: Prefer native over vendor")
Link: https://bugzilla.redhat.com/show_bug.cgi?id=2161428
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The HP Pavilion g6-1d80nr predates Windows 8, so it defaults to using
acpi_video# for backlight control, but this is non functional on
this model.
Add a DMI quirk to use the native backlight interface which does
work properly.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Pull VFIO fixes from Alex Williamson:
- Honor reserved regions when testing for IOMMU find grained super page
support, avoiding a regression on s390 for a firmware device where
the existence of the mapping, even if unused can trigger an error
state. (Niklas Schnelle)
- Fix a deadlock in releasing KVM references by using the alternate
.release() rather than .destroy() callback for the kvm-vfio device.
(Yi Liu)
* tag 'vfio-v6.2-rc6' of https://github.com/awilliam/linux-vfio:
kvm/vfio: Fix potential deadlock on vfio group_lock
vfio/type1: Respect IOMMU reserved regions in vfio_test_domain_fgsp()
Pull EFI fixes from Ard Biesheuvel:
"Another couple of EFI fixes, of which the first two were already in
-next when I sent out the previous PR, but they caused some issues on
non-EFI boots so I let them simmer for a bit longer.
- ensure the EFI ResetSystem and ACPI PRM calls are recognized as
users of the EFI runtime, and therefore protected against
exceptions
- account for the EFI runtime stack in the stacktrace code
- remove Matthew Garrett's MAINTAINERS entry for efivarfs"
* tag 'efi-fixes-for-v6.2-2' of git://git.kernel.org/pub/scm/linux/kernel/git/efi/efi:
efi: Remove Matthew Garrett as efivarfs maintainer
arm64: efi: Account for the EFI runtime stack in stack unwinder
arm64: efi: Avoid workqueue to check whether EFI runtime is live
The definition of intel_selftest_modify_policy() does not match the
declaration, as gcc-13 points out:
drivers/gpu/drm/i915/selftests/intel_scheduler_helpers.c:29:5: error: conflicting types for 'intel_selftest_modify_policy' due to enum/integer mismatch; have 'int(struct intel_engine_cs *, struct intel_selftest_saved_policy *, u32)' {aka 'int(struct intel_engine_cs *, struct intel_selftest_saved_policy *, unsigned int)'} [-Werror=enum-int-mismatch]
29 | int intel_selftest_modify_policy(struct intel_engine_cs *engine,
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~
In file included from drivers/gpu/drm/i915/selftests/intel_scheduler_helpers.c:11:
drivers/gpu/drm/i915/selftests/intel_scheduler_helpers.h:28:5: note: previous declaration of 'intel_selftest_modify_policy' with type 'int(struct intel_engine_cs *, struct intel_selftest_saved_policy *, enum selftest_scheduler_modify)'
28 | int intel_selftest_modify_policy(struct intel_engine_cs *engine,
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~
Change the type in the definition to match.
Fixes: 617e87c05c ("drm/i915/selftest: Fix hangcheck self test for GuC submission")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Andi Shyti <andi.shyti@linux.intel.com>
Signed-off-by: Andi Shyti <andi.shyti@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230117163743.1003219-1-arnd@kernel.org
(cherry picked from commit 8d7eb8ed3f)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Commit 0d0e7d1eea ("drm/i915/mtl: Define engine context layouts")
added the engine context for Meteor Lake. In a second revision of the
patch it was believed the xcs offsets were wrong due to a tagging
issue in the spec. The first version was actually correct, as shown
by the intel_lrc_live_selftests/live_lrc_layout test:
i915: Running gt_lrc
i915: Running intel_lrc_live_selftests/live_lrc_layout
bcs0: LRI command mismatch at dword 1, expected 1108101d found 11081019
[drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:236:DP-1] disconnected
bcs0: HW register image:
[0000] 00000000 1108101d 00022244 ffff0008 00022034 00000088 00022030 00000088
...
bcs0: SW register image:
[0000] 00000000 11081019 00022244 00090009 00022034 00000000 00022030 00000000
The difference in the 2 additional dwords (0x1d vs 0x19) are the offsets
0x120 / 0x124 that are indeed part of the context image.
Bspec: 45585
Fixes: 0d0e7d1eea ("drm/i915/mtl: Define engine context layouts")
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230111235531.3353815-2-radhakrishna.sripada@intel.com
(cherry picked from commit ca54a9a32d)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
ctrl->ops is used by nvme_alloc_admin_tag_set() but set by
nvme_init_ctrl() so reorder the calls to avoid a NULL pointer
dereference.
Fixes: 6dfba1c09c ("nvme-fc: use the tagset alloc/free helpers")
Signed-off-by: Ross Lagerwall <ross.lagerwall@citrix.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
nfsd_file_cache_purge is called when the server is shutting down, in
which case, tearing things down is generally fine, but it also gets
called when the exports cache is flushed.
Instead of walking the cache and freeing everything unconditionally,
handle it the same as when we have a notification of conflicting access.
Fixes: ac3a2585f0 ("nfsd: rework refcounting in filecache")
Reported-by: Ruben Vestergaard <rubenv@drcmr.dk>
Reported-by: Torkil Svensgaard <torkil@drcmr.dk>
Reported-by: Shachar Kagan <skagan@nvidia.com>
Signed-off-by: Jeff Layton <jlayton@kernel.org>
Tested-by: Shachar Kagan <skagan@nvidia.com>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Commit 1d2e9b67b0 ("ARM: 9265/1: pass -march= only to compiler") added
a __thumb2__ define to ASFLAGS to avoid build errors in the crypto code,
which relies on __thumb2__ for preprocessing. Commit 59e2cf8d21 ("ARM:
9275/1: Drop '-mthumb' from AFLAGS_ISA") followed up on this by removing
-mthumb from AFLAGS so that __thumb2__ would not be defined when the
default target was ARMv7 or newer.
Unfortunately, the second commit's fix assumes that the toolchain
defaults to -mno-thumb / -marm, which is not the case for Debian's
arm-linux-gnueabihf target, which defaults to -mthumb:
$ echo | arm-linux-gnueabihf-gcc -dM -E - | grep __thumb
#define __thumb2__ 1
#define __thumb__ 1
This target is used by several CI systems, which will still see
redefined macro warnings, despite '-mthumb' not being present in the
flags:
<command-line>: warning: "__thumb2__" redefined
<built-in>: note: this is the location of the previous definition
Remove the global AFLAGS __thumb2__ define and move it to the crypto
folder where it is required by the imported OpenSSL algorithms; the rest
of the kernel should use the internal CONFIG_THUMB2_KERNEL symbol to
know whether or not Thumb2 is being used or not. Be sure that __thumb2__
is undefined first so that there are no macro redefinition warnings.
Link: https://github.com/ClangBuiltLinux/linux/issues/1772
Reported-by: "kernelci.org bot" <bot@kernelci.org>
Suggested-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Tested-by: Nick Desaulniers <ndesaulniers@google.com>
Fixes: 59e2cf8d21 ("ARM: 9275/1: Drop '-mthumb' from AFLAGS_ISA")
Fixes: 1d2e9b67b0 ("ARM: 9265/1: pass -march= only to compiler")
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
If we're using ring provided buffers with multishot receive, and we end
up doing an io-wq based issue at some points that also needs to select
a buffer, we'll lose the initially assigned buffer group as
io_ring_buffer_select() correctly clears the buffer group list as the
issue isn't serialized by the ctx uring_lock. This is fine for normal
receives as the request puts the buffer and finishes, but for multishot,
we will re-arm and do further receives. On the next trigger for this
multishot receive, the receive will try and pick from a buffer group
whose value is the same as the buffer ID of the las receive. That is
obviously incorrect, and will result in a premature -ENOUFS error for
the receive even if we had available buffers in the correct group.
Cache the buffer group value at prep time, so we can restore it for
future receives. This only needs doing for the above mentioned case, but
just do it by default to keep it easier to read.
Cc: stable@vger.kernel.org
Fixes: b3fdea6ecb ("io_uring: multishot recv")
Fixes: 9bb66906f2 ("io_uring: support multishot in recvmsg")
Cc: Dylan Yudaken <dylany@meta.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The majority of the driver already uses struct iosys_map to encapsulate
accesses to I/O remapped vs. system memory. Accesses via the screen base
pointer still use __iomem annotations, which can lead to inconsistencies
and conflicts with subsequent patches.
Convert the screen base to a struct iosys_map as well for consistency
and to avoid these issues.
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230120173103.4002342-5-thierry.reding@gmail.com
When proxying IPv6 NDP requests, the adverts to the initial multicast
solicits are correct and working. On the other hand, when later a
reachability confirmation is requested (on unicast), no reply is sent.
This causes the neighbor entry expiring on the sending node, which is
mostly a non-issue, as a new multicast request is sent. There are
routers, where the multicast requests are intentionally delayed, and in
these environments the current implementation causes periodic packet
loss for the proxied endpoints.
The root cause is the erroneous decrease of the hop limit, as this
is checked in ndisc.c and no answer is generated when it's 254 instead
of the correct 255.
Cc: stable@vger.kernel.org
Fixes: 46c7655f0b ("ipv6: decrease hop limit counter in ip6_forward()")
Signed-off-by: Gergely Risko <gergely.risko@gmail.com>
Tested-by: Gergely Risko <gergely.risko@gmail.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean say:
====================
ethtool support for IEEE 802.3 MAC Merge layer
Change log
----------
v3->v4:
- add missing opening bracket in ocelot_port_mm_irq()
- moved cfg.verify_time range checking so that it actually takes place
for the updated rather than old value
v3 at:
https://patchwork.kernel.org/project/netdevbpf/cover/20230117085947.2176464-1-vladimir.oltean@nxp.com/
v2->v3:
- made get_mm return int instead of void
- deleted ETHTOOL_A_MM_SUPPORTED
- renamed ETHTOOL_A_MM_ADD_FRAG_SIZE to ETHTOOL_A_MM_TX_MIN_FRAG_SIZE
- introduced ETHTOOL_A_MM_RX_MIN_FRAG_SIZE
- cleaned up documentation
- rebased on top of PLCA changes
- renamed ETHTOOL_STATS_SRC_* to ETHTOOL_MAC_STATS_SRC_*
v2 at:
https://patchwork.kernel.org/project/netdevbpf/cover/20230111161706.1465242-1-vladimir.oltean@nxp.com/
v1->v2:
I've decided to focus just on the MAC Merge layer for now, which is why
I am able to submit this patch set as non-RFC.
v1 (RFC) at:
https://patchwork.kernel.org/project/netdevbpf/cover/20220816222920.1952936-1-vladimir.oltean@nxp.com/
What is being introduced
------------------------
TL;DR: a MAC Merge layer as defined by IEEE 802.3-2018, clause 99
(interspersing of express traffic). This is controlled through ethtool
netlink (ETHTOOL_MSG_MM_GET, ETHTOOL_MSG_MM_SET). The raw ethtool
commands are posted here:
https://patchwork.kernel.org/project/netdevbpf/cover/20230111153638.1454687-1-vladimir.oltean@nxp.com/
The MAC Merge layer has its own statistics counters
(ethtool --include-statistics --show-mm swp0) as well as two member
MACs, the statistics of which can be queried individually, through a new
ethtool netlink attribute, corresponding to:
$ ethtool -I --show-pause eno2 --src aggregate
$ ethtool -S eno2 --groups eth-mac eth-phy eth-ctrl rmon -- --src pmac
The core properties of the MAC Merge layer are described in great detail
in patches 02/12 and 03/12. They can be viewed in "make htmldocs" format.
Devices for which the API is supported
--------------------------------------
I decided to start with the Ethernet switch on NXP LS1028A (Felix)
because of the smaller patch set. I also have support for the ENETC
controller pending.
I would like to get confirmation that the UAPI being proposed here will
not restrict any use cases known by other hardware vendors.
Why is support for preemptible traffic classes not here?
--------------------------------------------------------
There is legitimate concern whether the 802.1Q portion of the standard
(which traffic classes go to the eMAC and which to the pMAC) should be
modeled in Linux using tc or using another UAPI. I think that is
stalling the entire series, but should be discussed separately instead.
Removing FP adminStatus support makes me confident enough to submit this
patch set without an RFC tag (meaning: I wouldn't mind if it was merged
as is).
What is submitted here is sufficient for an LLDP daemon to do its job.
I've patched openlldp to advertise and configure frame preemption:
https://github.com/vladimiroltean/openlldp/tree/frame-preemption-v3
In case someone wants to try it out, here are some commands I've used.
# Configure the interfaces to receive and transmit LLDP Data Units
lldptool -L -i eno0 adminStatus=rxtx
lldptool -L -i swp0 adminStatus=rxtx
# Enable the transmission of certain TLVs on switch's interface
lldptool -T -i eno0 -V addEthCap enableTx=yes
lldptool -T -i swp0 -V addEthCap enableTx=yes
# Query LLDP statistics on switch's interface
lldptool -S -i swp0
# Query the received neighbor TLVs
lldptool -i swp0 -t -n -V addEthCap
Additional Ethernet Capabilities TLV
Preemption capability supported
Preemption capability enabled
Preemption capability active
Additional fragment size: 60 octets
So using this patch set, lldpad will be able to advertise and configure
frame preemption, but still, no data packet will be sent as preemptible
over the link, because there is no UAPI to control which traffic classes
are sent as preemptible and which as express.
Preemptable or preemptible?
---------------------------
IEEE 802.3 uses "preemptable" throughout. IEEE 802.1Q uses "preemptible"
throughout. Because the definition of "preemptible" falls under 802.1Q's
jurisdiction and 802.3 just references it, I went with the 802.1Q naming
even where supporting an 802.3 feature. Also, checkpatch agrees with this.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Due to the fact that the kernel-side data structures have been carried
over from the ioctl-based ethtool, we are now in the situation where we
have an ethnl_update_bool32() function, but the plain function that
operates on a boolean value kept in an actual u8 netlink attribute
doesn't exist.
With new ethtool features that are exposed solely over netlink, the
kernel data structures will use the "bool" type, so we will need this
kind of helper. Introduce it now; it's needed for things like
verify-disabled for the MAC merge configuration.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The original goal with drm_edid_connector_update() was to have a single
call for updating the connector and adding probed modes, in this order,
but that turned out to be problematic. Drivers that need to update the
connector in the .detect() callback would end up updating the probed
modes as well. Turns out the callback may be called so many times that
the probed mode list fills up without bounds, and this is amplified by
add_alternate_cea_modes() duplicating the CEA modes on every call,
actually running out of memory on some machines.
Kudos to Imre Deak <imre.deak@intel.com> for explaining this to me.
Go back to having separate drm_edid_connector_update() and
drm_edid_connector_add_modes() calls. The former may be called from
.detect(), .force(), or .get_modes(), but the latter only from
.get_modes().
Unlike drm_add_edid_modes(), have drm_edid_connector_add_modes() update
the probed modes from the EDID property instead of the passed in
EDID. This is mainly to enforce two things:
1) drm_edid_connector_update() must be called before
drm_edid_connector_add_modes().
Display info and quirks are needed for parsing the modes, and we
don't want to call update_display_info() again to ensure the info is
available, like drm_add_edid_modes() does.
2) The same EDID is used for both updating the connector and adding the
probed modes.
Fortunately, the change is easy, because no driver has actually adopted
drm_edid_connector_update(). Not even i915, and that's mainly because of
the problem described above.
Cc: Imre Deak <imre.deak@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/e86fff1579f14ebf6334692526c8f6831cd02cac.1674144945.git.jani.nikula@intel.com
Separate the parsing of display info and modes from the HDMI VSDB. This
is prerequisite work for overall better separation of the two parsing
steps.
The info parsing is about figuring out whether the sink supports HDMI
infoframes. Since they were added in HDMI 1.4, assume the sink supports
HDMI infoframes if it has the HDMI_Video_present bit set (introduced in
HDMI 1.4). For details, see commit f1781e9bb2 ("drm/edid: Allow HDMI
infoframe without VIC or S3D").
The logic is not exactly the same, but since it was somewhat heuristic
to begin with, assume this is close enough.
v2:
- Simplify to only check HDMI_Video_present bit (Ville)
- Drop cea_db_raw_size() helper (Ville)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/238e15f7ab15a86f7fd1812271dcaec9bc6e1506.1674144945.git.jani.nikula@intel.com
Same to i.MX8mp LDB, i.MX93 LDB is controlled by mediamix blk-ctrl
through LDB_CTRL and LVDS_CTRL registers. i.MX93 LDB supports only
one LVDS channel(channel 0) and it's LVDS_CTRL register bit1 is used
as LVDS_EN instead of CH1_EN. Add i.MX93 LDB support in the existing
i.MX8mp LDB bridge driver by adding i.MX93 LDB compatible string and
device data(to reflect different register offsets and LVDS_CTRL register
bit1 definition).
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Liu Ying <victor.liu@nxp.com>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230123021449.969243-3-victor.liu@nxp.com
Same to i.MX8mp LDB, i.MX93 LDB is controlled by mediamix blk-ctrl
through 'ldb' register and 'lvds' register. Also, the 'ldb' clock
is required. i.MX93 LDB supports only one LVDS channel(channel 0,
a.k.a, LVDS Channel-A in the device tree binding documentation), while
i.MX8mp LDB supports at most two. Add i.MX93 LDB device tree binding
in the existing i.MX8mp LDB device tree binding documentation.
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Liu Ying <victor.liu@nxp.com>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230123021449.969243-2-victor.liu@nxp.com
Pull scheduler fixes from Borislav Petkov:
- Make sure the scheduler doesn't use stale frequency scaling values
when latter get disabled due to a value error
- Fix a NULL pointer access on UP configs
- Use the proper locking when updating CPU capacity
* tag 'sched_urgent_for_v6.2_rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/aperfmperf: Erase stale arch_freq_scale values when disabling frequency invariance readings
sched/core: Fix NULL pointer access fault in sched_setaffinity() with non-SMP configs
sched/fair: Fixes for capacity inversion detection
sched/uclamp: Fix a uninitialized variable warnings
Pull EDAC fixes from Borislav Petkov:
- Respect user-supplied polling value in the EDAC device code
- Fix a use-after-free issue in qcom_edac
* tag 'edac_urgent_for_v6.2_rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/ras/ras:
EDAC/qcom: Do not pass llcc_driv_data as edac_device_ctl_info's pvt_info
EDAC/device: Respect any driver-supplied workqueue polling value
Pull perf fix from Borislav Petkov:
- Add Emerald Rapids model support to more perf machinery
* tag 'perf_urgent_for_v6.2_rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/x86/intel/cstate: Add Emerald Rapids
perf/x86/intel: Add Emerald Rapids
Pull gfs2 writepage fix from Andreas Gruenbacher:
- Fix a regression introduced by commit "gfs2: stop using
generic_writepages in gfs2_ail1_start_one".
* tag 'gfs2-v6.2-rc4-fix' of git://git.kernel.org/pub/scm/linux/kernel/git/gfs2/linux-gfs2:
Revert "gfs2: stop using generic_writepages in gfs2_ail1_start_one"
reclaim_period_ms used to be positive only but the commit 0001725d0f
("KVM: selftests: Add atoi_positive() and atoi_non_negative() for input
validation") incorrectly changed it to non-negative validation.
Change validation to allow only positive input.
Fixes: 0001725d0f ("KVM: selftests: Add atoi_positive() and atoi_non_negative() for input validation")
Signed-off-by: Vipin Sharma <vipinsh@google.com>
Reported-by: Ben Gardon <bgardon@google.com>
Reviewed-by: Ben Gardon <bgardon@google.com>
Reviewed-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20230111183408.104491-1-vipinsh@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When serializing and deserializing kvm_sregs, attributes of the segment
descriptors are stored by user space. For unusable segments,
vmx_segment_access_rights skips all attributes and sets them to 0.
This means we zero out the DPL (Descriptor Privilege Level) for unusable
entries.
Unusable segments are - contrary to their name - usable in 64bit mode and
are used by guests to for example create a linear map through the
NULL selector.
VMENTER checks if SS.DPL is correct depending on the CS segment type.
For types 9 (Execute Only) and 11 (Execute Read), CS.DPL must be equal to
SS.DPL [1].
We have seen real world guests setting CS to a usable segment with DPL=3
and SS to an unusable segment with DPL=3. Once we go through an sregs
get/set cycle, SS.DPL turns to 0. This causes the virtual machine to crash
reproducibly.
This commit changes the attribute logic to always preserve attributes for
unusable segments. According to [2] SS.DPL is always saved on VM exits,
regardless of the unusable bit so user space applications should have saved
the information on serialization correctly.
[3] specifies that besides SS.DPL the rest of the attributes of the
descriptors are undefined after VM entry if unusable bit is set. So, there
should be no harm in setting them all to the previous state.
[1] Intel SDM Vol 3C 26.3.1.2 Checks on Guest Segment Registers
[2] Intel SDM Vol 3C 27.3.2 Saving Segment Registers and Descriptor-Table
Registers
[3] Intel SDM Vol 3C 26.3.2.2 Loading Guest Segment Registers and
Descriptor-Table Registers
Cc: Alexander Graf <graf@amazon.de>
Cc: stable@vger.kernel.org
Signed-off-by: Hendrik Borghorst <hborghor@amazon.de>
Reviewed-by: Jim Mattson <jmattson@google.com>
Reviewed-by: Alexander Graf <graf@amazon.com>
Message-Id: <20221114164823.69555-1-hborghor@amazon.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Placing a declaration of evt_reset is pedantically invalid
according to the C standard. While GCC does not really care
and only warns with -Wpedantic, clang ignores the declaration
altogether with an error:
x86_64/xen_shinfo_test.c:965:2: error: expected expression
struct kvm_xen_hvm_attr evt_reset = {
^
x86_64/xen_shinfo_test.c:969:38: error: use of undeclared identifier evt_reset
vm_ioctl(vm, KVM_XEN_HVM_SET_ATTR, &evt_reset);
^
Reported-by: Yu Zhang <yu.c.zhang@linux.intel.com>
Reported-by: Sean Christopherson <seanjc@google.com>
Fixes: a79b53aaaa ("KVM: x86: fix deadlock for KVM_XEN_EVTCHN_RESET", 2022-12-28)
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
