Saeed Mahameed says:
====================
mlx5-updates-2020-02-27
mlx5 misc updates and minor cleanups:
1) Use per vport tables for mirroring
2) Improve log messages for SW steering (DR)
3) Add devlink fdb_large_groups parameter
4) E-Switch, Allow goto earlier chain
5) Don't allow forwarding between uplink representors
6) Add support for devlink-port in non-representors mode
7) Minor misc cleanups
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The mptcp conflict was overlapping additions.
The SMC conflict was an additional and removal happening at the same
time.
Signed-off-by: David S. Miller <davem@davemloft.net>
When using port mirroring, we forward the traffic to another table and
use that table to forward to the mirrored vport. Since the hardware
loses the values of reg c, and in particular reg c0, we fail the match
on the input vport which previously existed in reg c0. To overcome this
situation, we use a set of per vport tables, positioned at the lowest
priority, and forward traffic to those tables. Since these tables are
per vport, we can avoid matching on reg c0.
Fixes: c01cfd0f11 ("net/mlx5: E-Switch, Add match on vport metadata for rule in fast path")
Signed-off-by: Eli Cohen <eli@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Reviewed-by: Paul Blakey <paulb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Pull networking fixes from David Miller:
1) Fix leak in nl80211 AP start where we leak the ACL memory, from
Johannes Berg.
2) Fix double mutex unlock in mac80211, from Andrei Otcheretianski.
3) Fix RCU stall in ipset, from Jozsef Kadlecsik.
4) Fix devlink locking in devlink_dpipe_table_register, from Madhuparna
Bhowmik.
5) Fix race causing TX hang in ll_temac, from Esben Haabendal.
6) Stale eth hdr pointer in br_dev_xmit(), from Nikolay Aleksandrov.
7) Fix TX hash calculation bounds checking wrt. tc rules, from Amritha
Nambiar.
8) Size netlink responses properly in schedule action code to take into
consideration TCA_ACT_FLAGS. From Jiri Pirko.
9) Fix firmware paths for mscc PHY driver, from Antoine Tenart.
10) Don't register stmmac notifier multiple times, from Aaro Koskinen.
11) Various rmnet bug fixes, from Taehee Yoo.
12) Fix vsock deadlock in vsock transport release, from Stefano
Garzarella.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (61 commits)
net: dsa: mv88e6xxx: Fix masking of egress port
mlxsw: pci: Wait longer before accessing the device after reset
sfc: fix timestamp reconstruction at 16-bit rollover points
vsock: fix potential deadlock in transport->release()
unix: It's CONFIG_PROC_FS not CONFIG_PROCFS
net: rmnet: fix packet forwarding in rmnet bridge mode
net: rmnet: fix bridge mode bugs
net: rmnet: use upper/lower device infrastructure
net: rmnet: do not allow to change mux id if mux id is duplicated
net: rmnet: remove rcu_read_lock in rmnet_force_unassociate_device()
net: rmnet: fix suspicious RCU usage
net: rmnet: fix NULL pointer dereference in rmnet_changelink()
net: rmnet: fix NULL pointer dereference in rmnet_newlink()
net: phy: marvell: don't interpret PHY status unless resolved
mlx5: register lag notifier for init network namespace only
unix: define and set show_fdinfo only if procfs is enabled
hinic: fix a bug of rss configuration
hinic: fix a bug of setting hw_ioctxt
hinic: fix a irq affinity bug
net/smc: check for valid ib_client_data
...
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Propagate the resolved link configuration down via DSA's
phylink_mac_link_up() operation to allow split PCS/MAC to work.
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Propagate the resolved link parameters via the mac_link_up() call for
MACs that do not automatically track their PCS state. We propagate the
link parameters via function arguments so that inappropriate members
of struct phylink_link_state can't be accessed, and creating a new
structure just for this adds needless complexity to the API.
Tested-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull HID subsystem fixes from Jiri Kosina:
- syzkaller-reported error handling fixes in various drivers, from
various people
- increase of HID report buffer size to 8K, which is apparently needed
by certain modern devices
- a few new device-ID-specific fixes / quirks
- battery charging status reporting fix in logitech-hidpp, from Filipe
Laíns
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/hid/hid:
HID: hid-bigbenff: fix race condition for scheduled work during removal
HID: hid-bigbenff: call hid_hw_stop() in case of error
HID: hid-bigbenff: fix general protection fault caused by double kfree
HID: i2c-hid: add Trekstor Surfbook E11B to descriptor override
HID: alps: Fix an error handling path in 'alps_input_configured()'
HID: hiddev: Fix race in in hiddev_disconnect()
HID: core: increase HID report buffer size to 8KiB
HID: core: fix off-by-one memset in hid_report_raw_event()
HID: apple: Add support for recent firmware on Magic Keyboards
HID: ite: Only bind to keyboard USB interface on Acer SW5-012 keyboard dock
HID: logitech-hidpp: BatteryVoltage: only read chargeStatus if extPower is active
Add a helper to change the owner of a device's sysfs entries. This
needs to happen when the ownership of a device is changed, e.g. when
moving network devices between network namespaces.
This function will be used to correctly account for ownership changes,
e.g. when moving network devices between network namespaces.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Christian Brauner <christian.brauner@ubuntu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a helper to change the owner of sysfs objects.
This function will be used to correctly account for kobject ownership
changes, e.g. when moving network devices between network namespaces.
This mirrors how a kobject is added through driver core which in its guts is
done via kobject_add_internal() which in summary creates the main directory via
create_dir(), populates that directory with the groups associated with the
ktype of the kobject (if any) and populates the directory with the basic
attributes associated with the ktype of the kobject (if any). These are the
basic steps that are associated with adding a kobject in sysfs.
Any additional properties are added by the specific subsystem itself (not by
driver core) after it has registered the device. So for the example of network
devices, a network device will e.g. register a queue subdirectory under the
basic sysfs directory for the network device and than further subdirectories
within that queues subdirectory. But that is all specific to network devices
and they call the corresponding sysfs functions to do that directly when they
create those queue objects. So anything that a subsystem adds outside of what
driver core does must also be changed by it (That's already true for removal of
files it created outside of driver core.) and it's the same for ownership
changes.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Christian Brauner <christian.brauner@ubuntu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add helpers to change the owner of sysfs groups.
This function will be used to correctly account for kobject ownership
changes, e.g. when moving network devices between network namespaces.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Christian Brauner <christian.brauner@ubuntu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a helper to change the owner of a sysfs link.
This function will be used to correctly account for kobject ownership
changes, e.g. when moving network devices between network namespaces.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Christian Brauner <christian.brauner@ubuntu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add helpers to change the owner of a sysfs files.
This function will be used to correctly account for kobject ownership
changes, e.g. when moving network devices between network namespaces.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Christian Brauner <christian.brauner@ubuntu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contains Netfilter fixes:
1) Perform garbage collection from workqueue to fix rcu detected
stall in ipset hash set types, from Jozsef Kadlecsik.
2) Fix the forceadd evaluation path, also from Jozsef.
3) Fix nft_set_pipapo selftest, from Stefano Brivio.
4) Crash when add-flush-add element in pipapo set, also from Stefano.
Add test to cover this crash.
5) Remove sysctl entry under mutex in hashlimit, from Cong Wang.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull tracing and bootconfig updates:
"Fixes and changes to bootconfig before it goes live in a release.
Change in API of bootconfig (before it comes live in a release):
- Have a magic value "BOOTCONFIG" in initrd to know a bootconfig
exists
- Set CONFIG_BOOT_CONFIG to 'n' by default
- Show error if "bootconfig" on cmdline but not compiled in
- Prevent redefining the same value
- Have a way to append values
- Added a SELECT BLK_DEV_INITRD to fix a build failure
Synthetic event fixes:
- Switch to raw_smp_processor_id() for recording CPU value in preempt
section. (No care for what the value actually is)
- Fix samples always recording u64 values
- Fix endianess
- Check number of values matches number of fields
- Fix a printing bug
Fix of trace_printk() breaking postponed start up tests
Make a function static that is only used in a single file"
* tag 'trace-v5.6-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
bootconfig: Fix CONFIG_BOOTTIME_TRACING dependency issue
bootconfig: Add append value operator support
bootconfig: Prohibit re-defining value on same key
bootconfig: Print array as multiple commands for legacy command line
bootconfig: Reject subkey and value on same parent key
tools/bootconfig: Remove unneeded error message silencer
bootconfig: Add bootconfig magic word for indicating bootconfig explicitly
bootconfig: Set CONFIG_BOOT_CONFIG=n by default
tracing: Clear trace_state when starting trace
bootconfig: Mark boot_config_checksum() static
tracing: Disable trace_printk() on post poned tests
tracing: Have synthetic event test use raw_smp_processor_id()
tracing: Fix number printing bug in print_synth_event()
tracing: Check that number of vals matches number of synth event fields
tracing: Make synth_event trace functions endian-correct
tracing: Make sure synth_event_trace() example always uses u64
Jozsef Kadlecsik says:
====================
ipset patches for nf
The first one is larger than usual, but the issue could not be solved simpler.
Also, it's a resend of the patch I submitted a few days ago, with a one line
fix on top of that: the size of the comment extensions was not taken into
account at reporting the full size of the set.
- Fix "INFO: rcu detected stall in hash_xxx" reports of syzbot
by introducing region locking and using workqueue instead of timer based
gc of timed out entries in hash types of sets in ipset.
- Fix the forceadd evaluation path - the bug was also uncovered by the syzbot.
====================
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Add cookie argument to devlink_trap_report() allowing driver to pass in
the user cookie. Pass on the cookie down to drop monitor code.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
If driver passed along the cookie, push it through Netlink.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend struct flow_action_entry in order to hold TC action cookie
specified by user inserting the action.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The icmpv6_send function has long had a static inline implementation
with an empty body for CONFIG_IPV6=n, so that code calling it doesn't
need to be ifdef'd. The new icmpv6_ndo_send function, which is intended
for drivers as a drop-in replacement with an identical function
signature, should follow the same pattern. Without this patch, drivers
that used to work with CONFIG_IPV6=n now result in a linker error.
Cc: Chen Zhou <chenzhou10@huawei.com>
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: 0b41713b60 ("icmp: introduce helper for nat'd source address in network device context")
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Johannes Berg says:
====================
A new set of changes:
* lots of small documentation fixes, from Jérôme Pouiller
* beacon protection (BIGTK) support from Jouni Malinen
* some initial code for TID configuration, from Tamizh chelvam
* I reverted some new API before it's actually used, because
it's wrong to mix controlled port and preauth
* a few other cleanups/fixes
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
It appears most ethernet drivers follow one of two main strategies
for mdio bus/phy management. A monolithic model where the net driver
itself creates, probes and uses the phy, and one where an external
mdio/phy driver instantiates the mdio bus/phy and the net driver
only attaches to a known phy. Usually in this latter model the phys
are discovered via DT relationships or simply phy name/address
hardcoding.
This is a shame because modern well behaved mdio buses are self
describing and can be probed. The mdio layer itself is fully capable
of this, yet there isn't a clean way for a standalone net driver
to attach and enumerate the discovered devices. This is because
outside of of_mdio_find_bus() there isn't a straightforward way
to acquire the mii_bus pointer.
So, lets add a mdio_find_bus which can return the mii_bus based
only on its name.
Signed-off-by: Jeremy Linton <jeremy.linton@arm.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Special handling is needed in bareudp module for IP & MPLS as they
support more than one ethertypes.
MPLS has 2 ethertypes. 0x8847 for MPLS unicast and 0x8848 for MPLS multicast.
While decapsulating MPLS packet from UDP packet the tunnel destination IP
address is checked to determine the ethertype. The ethertype of the packet
will be set to 0x8848 if the tunnel destination IP address is a multicast
IP address. The ethertype of the packet will be set to 0x8847 if the
tunnel destination IP address is a unicast IP address.
IP has 2 ethertypes.0x0800 for IPV4 and 0x86dd for IPv6. The version
field of the IP header tunnelled will be checked to determine the ethertype.
This special handling to tunnel additional ethertypes will be disabled
by default and can be enabled using a flag called multiproto. This flag can
be used only with ethertypes 0x8847 and 0x0800.
Signed-off-by: Martin Varghese <martin.varghese@nokia.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Bareudp tunnel module provides a generic L3 encapsulation
tunnelling module for tunnelling different protocols like MPLS,
IP,NSH etc inside a UDP tunnel.
Signed-off-by: Martin Varghese <martin.varghese@nokia.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add packet traps that can report packets that were dropped during ACL
processing.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull kvm fixes from Paolo Bonzini:
"Bugfixes, including the fix for CVE-2020-2732 and a few issues found
by 'make W=1'"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: s390: rstify new ioctls in api.rst
KVM: nVMX: Check IO instruction VM-exit conditions
KVM: nVMX: Refactor IO bitmap checks into helper function
KVM: nVMX: Don't emulate instructions in guest mode
KVM: nVMX: Emulate MTF when performing instruction emulation
KVM: fix error handling in svm_hardware_setup
KVM: SVM: Fix potential memory leak in svm_cpu_init()
KVM: apic: avoid calculating pending eoi from an uninitialized val
KVM: nVMX: clear PIN_BASED_POSTED_INTR from nested pinbased_ctls only when apicv is globally disabled
KVM: nVMX: handle nested posted interrupts when apicv is disabled for L1
kvm: x86: svm: Fix NULL pointer dereference when AVIC not enabled
KVM: VMX: Add VMX_FEATURE_USR_WAIT_PAUSE
KVM: nVMX: Hold KVM's srcu lock when syncing vmcs12->shadow
KVM: x86: don't notify userspace IOAPIC on edge-triggered interrupt EOI
kvm/emulate: fix a -Werror=cast-function-type
KVM: x86: fix incorrect comparison in trace event
KVM: nVMX: Fix some obsolete comments and grammar error
KVM: x86: fix missing prototypes
KVM: x86: enable -Werror
This patch adds support to configure per TID retry configuration
through the NL80211_TID_CONFIG_ATTR_RETRY_SHORT and
NL80211_TID_CONFIG_ATTR_RETRY_LONG attributes. This TID specific
retry configuration will have more precedence than phy level
configuration.
Signed-off-by: Tamizh chelvam <tamizhr@codeaurora.org>
Link: https://lore.kernel.org/r/1579506687-18296-3-git-send-email-tamizhr@codeaurora.org
[rebase completely on top of my previous API changes]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Make some changes to the TID-config API:
* use u16 in nl80211 (only, and restrict to using 8 bits for now),
to avoid issues in the future if we ever want to use higher TIDs.
* reject empty TIDs mask (via netlink policy)
* change feature advertising to not use extended feature flags but
have own mechanism for this, which simplifies the code
* fix all variable names from 'tid' to 'tids' since it's a mask
* change to cfg80211_ name prefixes, not ieee80211_
* fix some minor docs/spelling things.
Change-Id: Ia234d464b3f914cdeab82f540e018855be580dce
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
IEEE P802.11-REVmd/D3.0 adds support for protecting Beacon frames using
a new set of keys (BIGTK; key index 6..7) similarly to the way
group-addressed Robust Management frames are protected (IGTK; key index
4..5). Extend cfg80211 and nl80211 to allow the new BIGTK to be
configured. Add an extended feature flag to indicate driver support for
the new key index values to avoid array overflows in driver
implementations and also to indicate to user space when this
functionality is available.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Link: https://lore.kernel.org/r/20200222132548.20835-2-jouni@codeaurora.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Pull irq fixes from Thomas Gleixner:
"Two fixes for the irq core code which are follow ups to the recent MSI
fixes:
- The WARN_ON which was put into the MSI setaffinity callback for
paranoia reasons actually triggered via a callchain which escaped
when all the possible ways to reach that code were analyzed.
The proc/irq/$N/*affinity interfaces have a quirk which came in
when ALPHA moved to the generic interface: In case that the written
affinity mask does not contain any online CPU it calls into ALPHAs
magic auto affinity setting code.
A few years later this mechanism was also made available to x86 for
no good reasons and in a way which circumvents all sanity checks
for interrupts which cannot have their affinity set from process
context on X86 due to the way the X86 interrupt delivery works.
It would be possible to make this work properly, but there is no
point in doing so. If the interrupt is not yet started then the
affinity setting has no effect and if it is started already then it
is already assigned to an online CPU so there is no point to
randomly move it to some other CPU. Just return EINVAL as the code
has done before that change forever.
- The new MSI quirk bit in the irq domain flags turned out to be
already occupied, which escaped the author and the reviewers
because the already in use bits were 0,6,2,3,4,5 listed in that
order.
That bit 6 was simply overlooked because the ordering was straight
forward linear otherwise. So the new bit ended up being a
duplicate.
Fix it up by switching the oddball 6 to the obvious 1"
* tag 'irq-urgent-2020-02-22' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
genirq/irqdomain: Make sure all irq domain flags are distinct
genirq/proc: Reject invalid affinity masks (again)
Pull SCSI fixes from James Bottomley:
"Four non-core fixes.
Two are reverts of target fixes which turned out to have unwanted side
effects, one is a revert of an RDMA fix with the same problem and the
final one fixes an incorrect warning about memory allocation failures
in megaraid_sas (the driver actually reduces the allocation size until
it succeeds)"
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: Revert "target: iscsi: Wait for all commands to finish before freeing a session"
scsi: Revert "RDMA/isert: Fix a recently introduced regression related to logout"
scsi: megaraid_sas: silence a warning
scsi: Revert "target/core: Inline transport_lun_remove_cmd()"
In the case of huge hash:* types of sets, due to the single spinlock of
a set the processing of the whole set under spinlock protection could take
too long.
There were four places where the whole hash table of the set was processed
from bucket to bucket under holding the spinlock:
- During resizing a set, the original set was locked to exclude kernel side
add/del element operations (userspace add/del is excluded by the
nfnetlink mutex). The original set is actually just read during the
resize, so the spinlocking is replaced with rcu locking of regions.
However, thus there can be parallel kernel side add/del of entries.
In order not to loose those operations a backlog is added and replayed
after the successful resize.
- Garbage collection of timed out entries was also protected by the spinlock.
In order not to lock too long, region locking is introduced and a single
region is processed in one gc go. Also, the simple timer based gc running
is replaced with a workqueue based solution. The internal book-keeping
(number of elements, size of extensions) is moved to region level due to
the region locking.
- Adding elements: when the max number of the elements is reached, the gc
was called to evict the timed out entries. The new approach is that the gc
is called just for the matching region, assuming that if the region
(proportionally) seems to be full, then the whole set does. We could scan
the other regions to check every entry under rcu locking, but for huge
sets it'd mean a slowdown at adding elements.
- Listing the set header data: when the set was defined with timeout
support, the garbage collector was called to clean up timed out entries
to get the correct element numbers and set size values. Now the set is
scanned to check non-timed out entries, without actually calling the gc
for the whole set.
Thanks to Florian Westphal for helping me to solve the SOFTIRQ-safe ->
SOFTIRQ-unsafe lock order issues during working on the patch.
Reported-by: syzbot+4b0e9d4ff3cf117837e5@syzkaller.appspotmail.com
Reported-by: syzbot+c27b8d5010f45c666ed1@syzkaller.appspotmail.com
Reported-by: syzbot+68a806795ac89df3aa1c@syzkaller.appspotmail.com
Fixes: 23c42a403a ("netfilter: ipset: Introduction of new commands and protocol version 7")
Signed-off-by: Jozsef Kadlecsik <kadlec@netfilter.org>
Daniel Borkmann says:
====================
pull-request: bpf-next 2020-02-21
The following pull-request contains BPF updates for your *net-next* tree.
We've added 25 non-merge commits during the last 4 day(s) which contain
a total of 33 files changed, 2433 insertions(+), 161 deletions(-).
The main changes are:
1) Allow for adding TCP listen sockets into sock_map/hash so they can be used
with reuseport BPF programs, from Jakub Sitnicki.
2) Add a new bpf_program__set_attach_target() helper for adding libbpf support
to specify the tracepoint/function dynamically, from Eelco Chaudron.
3) Add bpf_read_branch_records() BPF helper which helps use cases like profile
guided optimizations, from Daniel Xu.
4) Enable bpf_perf_event_read_value() in all tracing programs, from Song Liu.
5) Relax BTF mandatory check if only used for libbpf itself e.g. to process
BTF defined maps, from Andrii Nakryiko.
6) Move BPF selftests -mcpu compilation attribute from 'probe' to 'v3' as it has
been observed that former fails in envs with low memlock, from Yonghong Song.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 736b46027e ("net: Add ID (if needed) to sock_reuseport and expose
reuseport_lock") has introduced lazy generation of reuseport group IDs that
survive group resize.
By comparing the identifier we check if BPF reuseport program is not trying
to select a socket from a BPF map that belongs to a different reuseport
group than the one the packet is for.
Because SOCKARRAY used to be the only BPF map type that can be used with
reuseport BPF, it was possible to delay the generation of reuseport group
ID until a socket from the group was inserted into BPF map for the first
time.
Now that SOCK{MAP,HASH} can be used with reuseport BPF we have two options,
either generate the reuseport ID on map update, like SOCKARRAY does, or
allocate an ID from the start when reuseport group gets created.
This patch takes the latter approach to keep sockmap free of calls into
reuseport code. This streamlines the reuseport_id access as its lifetime
now matches the longevity of reuseport object.
The cost of this simplification, however, is that we allocate reuseport IDs
for all SO_REUSEPORT users. Even those that don't use SOCKARRAY in their
setups. With the way identifiers are currently generated, we can have at
most S32_MAX reuseport groups, which hopefully is sufficient. If we ever
get close to the limit, we can switch an u64 counter like sk_cookie.
Another change is that we now always call into SOCKARRAY logic to unlink
the socket from the map when unhashing or closing the socket. Previously we
did it only when at least one socket from the group was in a BPF map.
It is worth noting that this doesn't conflict with sockmap tear-down in
case a socket is in a SOCK{MAP,HASH} and belongs to a reuseport
group. sockmap tear-down happens first:
prot->unhash
`- tcp_bpf_unhash
|- tcp_bpf_remove
| `- while (sk_psock_link_pop(psock))
| `- sk_psock_unlink
| `- sock_map_delete_from_link
| `- __sock_map_delete
| `- sock_map_unref
| `- sk_psock_put
| `- sk_psock_drop
| `- rcu_assign_sk_user_data(sk, NULL)
`- inet_unhash
`- reuseport_detach_sock
`- bpf_sk_reuseport_detach
`- WRITE_ONCE(sk->sk_user_data, NULL)
Suggested-by: Martin Lau <kafai@fb.com>
Signed-off-by: Jakub Sitnicki <jakub@cloudflare.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20200218171023.844439-10-jakub@cloudflare.com
