* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (79 commits)
powerpc/8xx: Add support for the MPC8xx based boards from TQC
powerpc/85xx: Introduce support for the Freescale P1022DS reference board
powerpc/85xx: Adding DTS for the STx GP3-SSA MPC8555 board
powerpc/85xx: Change deprecated binding for 85xx-based boards
powerpc/tqm85xx: add a quirk for ti1520 PCMCIA bridge
powerpc/tqm85xx: update PCI interrupt-map attribute
powerpc/mpc8308rdb: support for MPC8308RDB board from Freescale
powerpc/fsl_pci: add quirk for mpc8308 pcie bridge
powerpc/85xx: Cleanup QE initialization for MPC85xxMDS boards
powerpc/85xx: Fix booting for P1021MDS boards
powerpc/85xx: Fix SWIOTLB initalization for MPC85xxMDS boards
powerpc/85xx: kexec for SMP 85xx BookE systems
powerpc/5200/i2c: improve i2c bus error recovery
of/xilinxfb: update tft compatible versions
powerpc/fsl-diu-fb: Support setting display mode using EDID
powerpc/5121: doc/dts-bindings: update doc of FSL DIU bindings
powerpc/5121: shared DIU framebuffer support
powerpc/5121: move fsl-diu-fb.h to include/linux
powerpc/5121: fsl-diu-fb: fix issue with re-enabling DIU area descriptor
powerpc/512x: add clock structure for Video-IN (VIU) unit
...
Instead of instantiating a whole thread_struct on the stack use only the
required parts of it.
Signed-off-by: Andreas Schwab <schwab@linux-m68k.org>
Tested-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
When CPU hotplug is used, some CPUs may be offline at the time a kexec is
performed. The subsequent kernel may expect these CPUs to be already running,
and will declare them stuck. On pseries, there's also a soft-offline (cede)
state that CPUs may be in; this can also cause problems as the kexeced kernel
may ask RTAS if they're online -- and RTAS would say they are. The CPU will
either appear stuck, or will cause a crash as we replace its cede loop beneath
it.
This patch kicks each present offline CPU awake before the kexec, so that
none are forever lost to these assumptions in the subsequent kernel.
Now, the behaviour is that all available CPUs that were offlined are now
online & usable after the kexec. This mimics the behaviour of a full reboot
(on which all CPUs will be restarted).
Signed-off-by: Matt Evans <matt@ozlabs.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Tidies some typos, KERN_INFO-ise an info msg, and add a debug msg showing
when the final sequence starts.
Also adds a comment to kexec_prepare_cpus_wait() to make note of a possible
problem; the need for kexec to deal with CPUs that failed to originally start
up.
Signed-off-by: Matt Evans <matt@ozlabs.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Currently we look pretty stupid when printing out a bunch of things in
prom_init.c. eg.
Max number of cores passed to firmware: 0x0000000000000080
So I've change this to print in decimal:
Max number of cores passed to firmware: 128 (NR_CPUS = 256)
This required adding a prom_print_dec() function and changing some
prom_printk() calls from %x to %lu.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We already defined start_cpu_decrementer() to invoke decrementer for AP as
the following path:
start_secondary() -> secondary_cpu_time_init() -> start_cpu_decrementer()
So remove these incorrect codes introduced from commit:
e7f75ad0 powerpc/47x: Base ppc476 support
And actually we really should not enable decrementer before calling set_dec().
Signed-off-by: Tiejun Chen <tiejun.chen@windriver.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Fix sizes of variables so correct values are exported via /proc.
Cast variable in comparison to avoid compiler error.
Signed-off-by: Matthew McClintock <msm@freescale.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
With dynamic PACAs, the kexecing CPU's PACA won't lie within the kernel
static data and there is a chance that something may stomp it when preparing
to kexec. This patch switches this final CPU to a static PACA just before
we pull the switch.
Signed-off-by: Matt Evans <matt@ozlabs.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We should use perf_sample_data_init() to initialize struct
perf_sample_data. As explained in the description of commit dc1d628a
("perf: Provide generic perf_sample_data initialization"), it is
possible for userspace to get the kernel to dereference data.raw,
so if it is not initialized, that means that unprivileged userspace
can possibly oops the kernel. Using perf_sample_data_init makes sure
it gets initialized to NULL.
This conversion should have been included in commit dc1d628a, but it
got missed.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The recent AMCC 405EX Rev D without Security uses a PVR value
that matches the old 405EXr Rev A/B with Security.
The 405EX Rev D without Security would be shown
incorrectly as an 405EXr. The pvr_mask of 0xffff0004
is no longer sufficient to distinguish the 405EX from 405EXr.
This patch replaces 2 entries in the cpu_specs table
and adds 8 more, each using pvr_mask of 0xffff000f
and appropriate pvr_value to distinguish the AMCC
PowerPC 405EX and 405EXr instances.
The cpu_name for these entries now includes the
Rev, in similar fashion to the 440GX.
Signed-off-by: Lee Nipper <lee.nipper@gmail.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Oooops... we missed these. We incorrectly converted strings
used when parsing the device-tree on pseries, thus breaking
access to drconf memory and hotplug memory.
While at it, also revert some variable names that represent
something the FW calls "lmb" and thus don't need to be converted
to "memblock".
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
---
via following scripts
FILES=$(find * -type f | grep -vE 'oprofile|[^K]config')
sed -i \
-e 's/lmb/memblock/g' \
-e 's/LMB/MEMBLOCK/g' \
$FILES
for N in $(find . -name lmb.[ch]); do
M=$(echo $N | sed 's/lmb/memblock/g')
mv $N $M
done
and remove some wrong change like lmbench and dlmb etc.
also move memblock.c from lib/ to mm/
Suggested-by: Ingo Molnar <mingo@elte.hu>
Acked-by: "H. Peter Anvin" <hpa@zytor.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We patch the TLB miss exception vectors to point to alternate
functions when using HW page table on BookE.
However, we were patching in a new branch in the first instruction
of the exception handler instead of the second one, thus overriding
the nop that is in the first instruction.
This cause problems when single stepping as we rely on that nop for
the single step to stop properly within the exception vector range
rather than on the target of the branch.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We use a similar technique to ppc32: We set a thread local flag
to indicate that we are about to enter or have entered the stop
state, and have fixup code in the async interrupt entry code that
reacts to this flag to make us return to a different location
(sets NIP to LINK in our case).
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
--
v2. Fix lockdep bug
Re-mask interrupts when coming back from idle
When booting a relocatable kernel it needs to jump to the correct
start address, which for BookE parts is usually unchanged
regardless of the physical memory offset.
Recent changes cause problems with how we calculate the start
address, it was always adding the RMO into the start address
which is incorrect. This patch only adds in the RMO offset
if we are in the kexec code path, as it needs the RMO to work
correctly.
Instead of adding the RMO offset in in the common code path, we
can just set r6 to the RMO offset in the kexec code path instead
of to zero, and finally perform the masking in the common code
path
Signed-off-by: Matthew McClintock <msm@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
If we are soft disabled and receive a doorbell exception we don't process
it immediately. This means we need to check on the way out of irq restore
if there are any doorbell exceptions to process.
The problem is at that point we don't know what our regs are, and that
in turn makes xmon unhappy. To workaround the problem, instead of checking
for and processing doorbells, we check for any doorbells and if there were
any we send ourselves another.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
include/asm-generic/irq_regs.h declares per-cpu irq_regs variables and
get_irq_regs() and set_irq_regs() helper functions to maintain them.
These can be used to access the proper pt_regs structure related to the
current interrupt entry (if any).
In the powerpc arch code, this is used to maintain irq regs on
decrementer and external interrupt exceptions. However, for the
doorbell exceptions used by the msgsnd/msgrcv IPI mechanism of newer
BookE CPUs, the irq_regs are not kept up to date.
In particular this means that xmon will not work properly on SMP,
because the secondary xmon instances started by IPI will blow up when
they cannot retrieve the irq regs.
This patch fixes the problem by adding calls to maintain the irq regs
across doorbell exceptions.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Note that critical doorbells are an unimplemented stub just like
other critical or machine check handlers, since we haven't done
support for "levelled" exceptions yet.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The decrementer on BookE acts as a level interrupt and doesn't
need to be re-triggered when going negative. It doesn't go
negative anyways (unless programmed to auto-reload with a
negative value) as it stops when reaching 0.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The doorbells use the content of the PIR register to match messages
from other CPUs. This may or may not be the same as our linux CPU
number, so using that as the "target" is no right.
Instead, we sample the PIR register at boot on every processor
and use that value subsequently when sending IPIs.
We also use a per-cpu message mask rather than a global array which
should limit cache line contention.
Note: We could use the CPU number in the device-tree instead of
the PIR register, as they are supposed to be equivalent. This
might prove useful if doorbells are to be used to kick CPUs out
of FW at boot time, thus before we can sample the PIR. This is
however not the case now and using the PIR just works.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Our handling of debug interrupts on Book3E 64-bit is not quite
the way it should be just yet. This is a workaround to let gdb
work at least for now. We ensure that when context switching,
we set the appropriate DBCR0 value for the new task. We also
make sure that we turn off MSR[DE] within the kernel, and set
it as part of the bits that get set when going back to userspace.
In the long run, we will probably set the userspace DBCR0 on the
exception exit code path and ensure we have some proper kernel
value to set on the way into the kernel, a bit like ppc32 does,
but that will take more work.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Currently the irqs for the i8042, which historically provides keyboard and
mouse (aux) support, is hardwired in the driver rather than parsing the
dts. This patch modifies the powerpc legacy IO code to attempt to parse
the device tree for this information, failing back to the hardcoded values
if it fails.
Signed-off-by: Martyn Welch <martyn.welch@ge.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Now we dynamically allocate the paca array, it takes an extra load
whenever we want to access another cpu's paca. One place we do that a lot
is per cpu variables. A simple example:
DEFINE_PER_CPU(unsigned long, vara);
unsigned long test4(int cpu)
{
return per_cpu(vara, cpu);
}
This takes 4 loads, 5 if you include the actual load of the per cpu variable:
ld r11,-32760(r30) # load address of paca pointer
ld r9,-32768(r30) # load link address of percpu variable
sldi r3,r29,9 # get offset into paca (each entry is 512 bytes)
ld r0,0(r11) # load paca pointer
add r3,r0,r3 # paca + offset
ld r11,64(r3) # load paca[cpu].data_offset
ldx r3,r9,r11 # load per cpu variable
If we remove the ppc64 specific per_cpu_offset(), we get the generic one
which indexes into a statically allocated array. This removes one load and
one add:
ld r11,-32760(r30) # load address of __per_cpu_offset
ld r9,-32768(r30) # load link address of percpu variable
sldi r3,r29,3 # get offset into __per_cpu_offset (each entry 8 bytes)
ldx r11,r11,r3 # load __per_cpu_offset[cpu]
ldx r3,r9,r11 # load per cpu variable
Having all the offsets in one array also helps when iterating over a per cpu
variable across a number of cpus, such as in the scheduler. Before we would
need to load one paca cacheline when calculating each per cpu offset. Now we
have 16 (128 / sizeof(long)) per cpu offsets in each cacheline.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Partition hibernation will use some of the same code as is
currently used for Live Partition Migration. This function
further abstracts this code such that code outside of rtas.c
can utilize it. It also changes the error field in the suspend
me data structure to be an atomic type, since it is set and
checked on different cpus without any barriers or locking.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Since the decrementer and timekeeping code was moved over to using
the generic clockevents and timekeeping infrastructure, several
variables and functions have been obsolete and effectively unused.
This deletes them.
In particular, wakeup_decrementer() is no longer needed since the
generic code reprograms the decrementer as part of the process of
resuming the timekeeping code, which happens during sysdev resume.
Thus the wakeup_decrementer calls in the suspend_enter methods for
52xx platforms have been removed. The call in the powermac cpu
frequency change code has been replaced by set_dec(1), which will
cause a timer interrupt as soon as interrupts are enabled, and the
generic code will then reprogram the decrementer with the correct
value.
This also simplifies the generic_suspend_en/disable_irqs functions
and makes them static since they are not referenced outside time.c.
The preempt_enable/disable calls are removed because the generic
code has disabled all but the boot cpu at the point where these
functions are called, so we can't be moved to another cpu.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Currently it is possible for userspace to see the result of
gettimeofday() going backwards by 1 microsecond, assuming that
userspace is using the gettimeofday() in the VDSO. The VDSO
gettimeofday() algorithm computes the time in "xsecs", which are
units of 2^-20 seconds, or approximately 0.954 microseconds,
using the algorithm
now = (timebase - tb_orig_stamp) * tb_to_xs + stamp_xsec
and then converts the time in xsecs to seconds and microseconds.
The kernel updates the tb_orig_stamp and stamp_xsec values every
tick in update_vsyscall(). If the length of the tick is not an
integer number of xsecs, then some precision is lost in converting
the current time to xsecs. For example, with CONFIG_HZ=1000, the
tick is 1ms long, which is 1048.576 xsecs. That means that
stamp_xsec will advance by either 1048 or 1049 on each tick.
With the right conditions, it is possible for userspace to get
(timebase - tb_orig_stamp) * tb_to_xs being 1049 if the kernel is
slightly late in updating the vdso_datapage, and then for stamp_xsec
to advance by 1048 when the kernel does update it, and for userspace
to then see (timebase - tb_orig_stamp) * tb_to_xs being zero due to
integer truncation. The result is that time appears to go backwards
by 1 microsecond.
To fix this we change the VDSO gettimeofday to use a new field in the
VDSO datapage which stores the nanoseconds part of the time as a
fractional number of seconds in a 0.32 binary fraction format.
(Or put another way, as a 32-bit number in units of 0.23283 ns.)
This is convenient because we can use the mulhwu instruction to
convert it to either microseconds or nanoseconds.
Since it turns out that computing the time of day using this new field
is simpler than either using stamp_xsec (as gettimeofday does) or
stamp_xtime.tv_nsec (as clock_gettime does), this converts both
gettimeofday and clock_gettime to use the new field. The existing
__do_get_tspec function is converted to use the new field and take
a parameter in r7 that indicates the desired resolution, 1,000,000
for microseconds or 1,000,000,000 for nanoseconds. The __do_get_xsec
function is then unused and is deleted.
The new algorithm is
now = ((timebase - tb_orig_stamp) << 12) * tb_to_xs
+ (stamp_xtime_seconds << 32) + stamp_sec_fraction
with 'now' in units of 2^-32 seconds. That is then converted to
seconds and either microseconds or nanoseconds with
seconds = now >> 32
partseconds = ((now & 0xffffffff) * resolution) >> 32
The 32-bit VDSO code also makes a further simplification: it ignores
the bottom 32 bits of the tb_to_xs value, which is a 0.64 format binary
fraction. Doing so gets rid of 4 multiply instructions. Assuming
a timebase frequency of 1GHz or less and an update interval of no
more than 10ms, the upper 32 bits of tb_to_xs will be at least
4503599, so the error from ignoring the low 32 bits will be at most
2.2ns, which is more than an order of magnitude less than the time
taken to do gettimeofday or clock_gettime on our fastest processors,
so there is no possibility of seeing inconsistent values due to this.
This also moves update_gtod() down next to its only caller, and makes
update_vsyscall use the time passed in via the wall_time argument rather
than accessing xtime directly. At present, wall_time always points to
xtime, but that could change in future.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
crash_kexec_wait_realmode() is defined only if CONFIG_PPC_STD_MMU_64
and CONFIG_SMP, but is called if CONFIG_PPC_STD_MMU_64 even if !CONFIG_SMP.
Fix the conditional compilation around the invocation.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Acked-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
When SPARSE_IRQ is set, irq_to_desc() can
return NULL. While the code here has a
check for NULL, it's not really correct.
Fix it by separating the check for it.
This fixes CPU hot unplug for me.
Reported-by: Alastair Bridgewater <alastair.bridgewater@gmail.com>
Cc: stable@kernel.org [2.6.32+]
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
If we configure with CONFIG_SMP=n or set NR_CPUS less than the number of
SMT threads we will set the max cores property to 0 in the
ibm,client-architecture-support structure. On new versions of firmware that
understand this property it obliges and terminates our partition.
Use DIV_ROUND_UP so we handle not only the CONFIG_SMP=n case but also the
case where NR_CPUS isn't a multiple of the number of SMT threads.
Signed-off-by: Anton Blanchard <anton@samba.org>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Just whitelist these extra compiler generated symbols.
Fixes these errors:
Error: External symbol '_restgpr0_14' referenced from prom_init.c
Error: External symbol '_restgpr0_20' referenced from prom_init.c
Error: External symbol '_restgpr0_22' referenced from prom_init.c
Error: External symbol '_restgpr0_24' referenced from prom_init.c
Error: External symbol '_restgpr0_25' referenced from prom_init.c
Error: External symbol '_restgpr0_26' referenced from prom_init.c
Error: External symbol '_restgpr0_27' referenced from prom_init.c
Error: External symbol '_restgpr0_28' referenced from prom_init.c
Error: External symbol '_restgpr0_29' referenced from prom_init.c
Error: External symbol '_restgpr0_31' referenced from prom_init.c
Error: External symbol '_savegpr0_14' referenced from prom_init.c
Error: External symbol '_savegpr0_20' referenced from prom_init.c
Error: External symbol '_savegpr0_22' referenced from prom_init.c
Error: External symbol '_savegpr0_24' referenced from prom_init.c
Error: External symbol '_savegpr0_25' referenced from prom_init.c
Error: External symbol '_savegpr0_26' referenced from prom_init.c
Error: External symbol '_savegpr0_27' referenced from prom_init.c
Error: External symbol '_savegpr0_28' referenced from prom_init.c
Error: External symbol '_savegpr0_29' referenced from prom_init.c
Error: External symbol '_savegpr0_31' referenced from prom_init.c
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Segher Boessenkool <segher@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
When power_pmu_disable() removes the given event from a particular index into
cpuhw->event[], it shuffles down higher event[] entries. But, this array is
paired with cpuhw->events[] and cpuhw->flags[] so should shuffle them
similarly.
If these arrays get out of sync, code such as power_check_constraints() will
fail. This caused a bug where events were temporarily disabled and then failed
to be re-enabled; subsequent code tried to write_pmc() with its (disabled) idx
of 0, causing a message "oops trying to write PMC0". This triggers this bug on
POWER7, running a miss-heavy test:
perf record -e L1-dcache-load-misses -e L1-dcache-store-misses ./misstest
Signed-off-by: Matt Evans <matt@ozlabs.org>
Acked-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
At present, hw_breakpoint_slots() returns 1 regardless of what
type of breakpoint is specified in the type argument. Since we
don't define CONFIG_HAVE_MIXED_BREAKPOINTS_REGS, there are
separate values for TYPE_INST and TYPE_DATA, and hw_breakpoint_slots()
returns 1 for both, effectively advertising instruction breakpoint
support which doesn't exist.
This fixes it by making hw_breakpoint_slots return 1 for TYPE_DATA
and 0 for TYPE_INST. This moves hw_breakpoint_slots() from the
powerpc hw_breakpoint.h to hw_breakpoint.c because the definitions
of TYPE_INST and TYPE_DATA aren't available in <asm/hw_breakpoint.h>.
They are defined in <linux/hw_breakpoint.h> but we can't include
that header in <asm/hw_breakpoint.h>, and nor can we rely on
<linux/hw_breakpoint.h> being included before <asm/hw_breakpoint.h>.
Since hw_breakpoint_slots() is only called at boot time, there is
no performance impact from making it a real function rather than
a static inline.
Signed-off-by: Paul Mackerras <paulus@samba.org>
The code we had to clear the MSR_SE bit was not doing anything because
the caller (ultimately single_step_exception() in traps.c) had already
cleared. Instead of trying to leave MSR_SE set if the TIF_SINGLESTEP
flag is set (which indicates that the process is being single-stepped
by ptrace), we instead return NOTIFY_DONE in that case, which means
the caller will generate a SIGTRAP for the process.
Signed-off-by: Paul Mackerras <paulus@samba.org>
The code would accept an access to an address one byte past the end
of the requested range as legitimate, due to having a "<=" rather than
a "<". This fixes that and cleans up the code a bit.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Many a times, the requested breakpoint length can be less than the
fixed breakpoint length i.e. 8 bytes supported by PowerPC 64-bit
server (Book III S) processors. This could lead to extraneous
interrupts resulting in false breakpoint notifications. This
detects and discards such interrupts for non-ptrace requests.
We don't change ptrace behaviour to avoid breaking compatability.
[Suggestion from Paul Mackerras <paulus@samba.org> to add a new flag in
'struct arch_hw_breakpoint' to identify extraneous interrupts]
Signed-off-by: K.Prasad <prasad@linux.vnet.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
A signal delivered between a hw_breakpoint_handler() and the
single_step_dabr_instruction() will not have the breakpoint active
while the signal handler is running -- the signal delivery will
set up a new MSR value which will not have MSR_SE set, so we
won't get the signal step interrupt until and unless the signal
handler returns (which it may never do).
To fix this, we restore the breakpoint when delivering a signal --
we clear the MSR_SE bit and set the DABR again. If the signal
handler returns, the DABR interrupt will occur again when the
instruction that we were originally trying to single-step gets
re-executed.
[Paul Mackerras <paulus@samba.org> pointed out the need to do this.]
Signed-off-by: K.Prasad <prasad@linux.vnet.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
If an alignment interrupt occurs on an instruction that is being
single-stepped, the alignment interrupt handler currently handles
the single-step condition by unconditionally sending a SIGTRAP to
the process. Other synchronous interrupts that result in the
instruction being emulated do likewise.
With hw_breakpoint support, the hw_breakpoint code needs to be able
to intercept these single-step events as well as those where the
instruction executes normally and a trace interrupt happens.
Fix this by making emulate_single_step() use the existing
single_step_exception() function instead of calling _exception()
directly. We then make single_step_exception() use the abstracted
clear_single_step() rather than clearing bits in the MSR image
directly so that emulate_single_step() will continue to work
correctly on Book 3E processors.
Signed-off-by: K.Prasad <prasad@linux.vnet.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Implement perf-events based hw-breakpoint interfaces for PowerPC
64-bit server (Book III S) processors. This allows access to a
given location to be used as an event that can be counted or
profiled by the perf_events subsystem.
This is done using the DABR (data breakpoint register), which can
also be used for process debugging via ptrace. When perf_event
hw_breakpoint support is configured in, the perf_event subsystem
manages the DABR and arbitrates access to it, and ptrace then
creates a perf_event when it is requested to set a data breakpoint.
[Adopted suggestions from Paul Mackerras <paulus@samba.org> to
- emulate_step() all system-wide breakpoints and single-step only the
per-task breakpoints
- perform arch-specific cleanup before unregistration through
arch_unregister_hw_breakpoint()
]
Signed-off-by: K.Prasad <prasad@linux.vnet.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
When trying to flash a machine via the update_flash command, Anton received the
following error:
Restarting system.
FLASH: kernel bug...flash list header addr above 4GB
The code in question has a comment that the flash list should be in
the kernel data and therefore under 4GB:
/* NOTE: the "first" block list is a global var with no data
* blocks in the kernel data segment. We do this because
* we want to ensure this block_list addr is under 4GB.
*/
Unfortunately the Kconfig option is marked tristate which means the variable
may not be in the kernel data and could be above 4GB.
Instead of relying on the data segment being below 4GB, use the static
data buffer allocated by the kernel for use by rtas. Since we don't
use the header struct directly anymore, convert it to a simple pointer.
Reported-By: Anton Blanchard <anton@samba.org>
Signed-Off-By: Milton Miller <miltonm@bga.com
Tested-By: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Irq stacks provide an essential protection from stack overflows through
external interrupts, at the cost of two additionals stacks per CPU.
Enable them unconditionally to simplify the kernel build and prevent
people from accidentally disabling them.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
kexec_perpare_cpus_wait() iterates i through NR_CPUS to check
paca[i].kexec_state of each to make sure they have quiesced.
However now we have dynamic PACA allocation, paca[NR_CPUS] is not necessarily
valid and we overrun the array; spurious "cpu is not possible, ignoring"
errors result. This patch iterates for_each_online_cpu so stays
within the bounds of paca[] -- and every CPU is now 'possible'.
Signed-off-by: Matt Evans <matt@ozlabs.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Linus Torvalds