Add a real platform bus device as a parent for
the srom class devices, to prevent non-platform
devices hanging from the bus root.
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Pull slave-dmaengine fixes from Vinod Koul:
"Two small fixes for omap dmaengine driver which fixes cyclic suspend
and resume"
* 'fixes' of git://git.infradead.org/users/vkoul/slave-dma:
dmaengine: omap-dma: Restore the CLINK_CTRL in resume path
dmaengine: omap-dma: Add memory barrier to dma_resume path
Pull ARM SoC fixes from Olof Johansson:
"Here's our last set of fixes for 3.17. Most of these are for TI
platforms, fixing some noisy Kconfig issues, runtime clock and power
issues on several platforms and NAND timings on DRA7.
There are also a couple of bug fixes for i.MX, one for QCOM and a
small fix to avoid section mismatch noise on PXA.
Diffstat looks large, partially due to some tables being updated and
thus touching many lines. The qcom gsbi change also restructures
clock management a bit and thus touches a bunch of lines.
All in all, a bit more changes than we'd like at this point, but
nothing stands out as risky either so it seems like the right thing to
send it up now instead of holding it to the merge window"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
drivers/soc: qcom: do not disable the iface clock in probe
ARM: imx: fix .is_enabled() of shared gate clock
ARM: OMAP3: Fix I/O chain clock line assertion timed out error
ARM: keystone: dts: fix bindings for pcie and usb clock nodes
bus: omap_l3_noc: Fix connID for OMAP4
ARM: DT: imx53: fix lvds channel 1 port
ARM: dts: cm-t54: fix serial console power supply.
ARM: dts: dra7-evm: Fix NAND GPMC timings
ARM: pxa: fix section mismatch warning for pxa_timer_nodt_init
ARM: OMAP: Fix Kconfig warning for omap1
Pull x86 fixes from Ingo Molnar:
"This has:
- EFI revert to fix a boot regression
- early_ioremap() fix for boot failure
- KASLR fix for possible boot failures
- EFI fix for corrupted string printing
- remove a misleading EFI bootup 'failed!' error message
Unfortunately it's all rather close to the merge window"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/efi: Truncate 64-bit values when calling 32-bit OutputString()
x86/efi: Delete misleading efi_printk() error message
Revert "efi/x86: efistub: Move shared dependencies to <asm/efi.h>"
x86/kaslr: Avoid the setup_data area when picking location
x86 early_ioremap: Increase FIX_BTMAPS_SLOTS to 8
Pull input fix from Dmitry Torokhov:
"A small fixup to i8042 adding Asus X450LCP to the nomux list"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: i8042 - fix Asus X450LCP touchpad detection
Merge fixes from Andrew Morton:
"9 fixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
mm: softdirty: keep bit when zapping file pte
fs/cachefiles: add missing \n to kerror conversions
genalloc: fix device node resource counter
drivers/rtc/rtc-efi.c: add missing module alias
mm, slab: initialize object alignment on cache creation
mm: softdirty: addresses before VMAs in PTE holes aren't softdirty
ocfs2/dlm: do not get resource spinlock if lockres is new
nilfs2: fix data loss with mmap()
ocfs2: free vol_label in ocfs2_delete_osb()
Pull ACPI and power management fixes from Rafael Wysocki:
"These are regression fixes (ACPI hotplug, cpufreq, hibernation, ACPI
LPSS driver), fixes for stuff that never worked correctly (ACPI GPIO
support in some cases and a wrong sign of an error code in the ACPI
core in one place), and one blacklist item for ACPI backlight
handling.
Specifics:
- Revert of a recent hibernation core commit that introduced a NULL
pointer dereference during resume for at least one user (Rafael J
Wysocki).
- Fix for the ACPI LPSS (Low-Power Subsystem) driver to disable
asynchronous PM callback execution for LPSS devices during system
suspend/resume (introduced in 3.16) which turns out to break
ordering expectations on some systems. From Fu Zhonghui.
- cpufreq core fix related to the handling of sysfs nodes during
system suspend/resume that has been broken for intel_pstate since
3.15 from Lan Tianyu.
- Restore the generation of "online" uevents for ACPI container
devices that was removed in 3.14, but some user space utilities
turn out to need them (Rafael J Wysocki).
- The cpufreq core fails to release a lock in an error code path
after changes made in 3.14. Fix from Prarit Bhargava.
- ACPICA and ACPI/GPIO fixes to make the handling of ACPI GPIO
operation regions (which means AML using GPIOs) work correctly in
all cases from Bob Moore and Srinivas Pandruvada.
- Fix for a wrong sign of the ACPI core's create_modalias() return
value in case of an error from Mika Westerberg.
- ACPI backlight blacklist entry for ThinkPad X201s from Aaron Lu"
* tag 'pm+acpi-3.17-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
Revert "PM / Hibernate: Iterate over set bits instead of PFNs in swsusp_free()"
gpio / ACPI: Use pin index and bit length
ACPICA: Update to GPIO region handler interface.
ACPI / platform / LPSS: disable async suspend/resume of LPSS devices
cpufreq: release policy->rwsem on error
cpufreq: fix cpufreq suspend/resume for intel_pstate
ACPI / scan: Correct error return value of create_modalias()
ACPI / video: disable native backlight for ThinkPad X201s
ACPI / hotplug: Generate online uevents for ACPI containers
Pull i2c fixes from Wolfram Sang:
"This is probably not the kind of pull request you want to see that
late in the cycle. Yet, the ACPI refactorization was problematic
again and caused another two issues which need fixing. My holidays
with limited internet (plus travelling) and the developer's illness
didn't help either :(
The details:
- ACPI code was refactored out into a seperate file and as a
side-effect, the i2c-core module got renamed. Jean Delvare
rightfully complained about the rename being problematic for
distributions. So, Mika and I thought the least problematic way to
deal with it is to move all the code back into the main i2c core
source file. This is mainly a huge code move with some #ifdeffery
applied. No functional code changes. Our personal tests and the
testbots did not find problems. (I was thinking about reverting,
too, yet that would also have ~800 lines changed)
- The new ACPI code also had a NULL pointer exception, thanks to
Peter for finding and fixing it.
- Mikko fixed a locking problem by decoupling clock_prepare and
clock_enable.
- Addy learnt that the datasheet was wrong and reimplemented the
frequency setup according to the new algorithm.
- Fan fixed an off-by-one error when copying data
- Janusz fixed a copy'n'paste bug which gave a wrong error message
- Sergei made sure that "don't touch" bits are not accessed"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: acpi: Fix NULL Pointer dereference
i2c: move acpi code back into the core
i2c: rk3x: fix divisor calculation for SCL frequency
i2c: mxs: fix error message in pio transfer
i2c: ismt: use correct length when copy buffer
i2c: rcar: fix RCAR_IRQ_ACK_{RECV|SEND}
i2c: tegra: Move clk_prepare/clk_set_rate to probe
* pm-cpufreq:
cpufreq: release policy->rwsem on error
cpufreq: fix cpufreq suspend/resume for intel_pstate
* pm-sleep:
Revert "PM / Hibernate: Iterate over set bits instead of PFNs in swsusp_free()"
Pull gpio fixes from Linus Walleij:
"Two GPIO fixes:
- GPIO direction flags where handled wrong in the new descriptor-
based API, so direction changes did not always "take".
- Fix a handler installation race in the generic GPIO irqchip code"
* tag 'gpio-v3.17-4' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpio: Fix potential NULL handler data in chained irqchip handler
gpio: Fix gpio direction flags not getting set
Pull EFI fixes from Matt Fleming:
* Revert the static library changes from the merge window since they're
causing issues for Macbooks and Fedora + Grub2 (Matt Fleming)
* Delete the misleading "setup_efi_pci() failed!" message which some
people are seeing when booting EFI (Matt Fleming)
* Fix printing strings from the 32-bit EFI boot stub by only passing
32-bit addresses to the firmware (Matt Fleming)
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Pull devicetree bug fixes and documentation from Grant Likely:
"Several bug fix commits for issues found in the v3.17 rc series.
Most of these are minor in that they aren't actively dangerous, but
they have been seen in the wild. The one important fix is commit
7dbe5849fb ("of: make sure of_alias is initialized before accessing
it"), without which some powerpc platforms will fail to find stdout
for the console"
* tag 'devicetree-for-linus' of git://git.secretlab.ca/git/linux:
of/fdt: fix memory range check
of: Fix memory block alignment in early_init_dt_add_memory_arch()
of: make sure of_alias is initialized before accessing it
of: Documentation regarding attaching OF Selftest testdata
of: Disabling OF functions that use sysfs if CONFIG_SYSFS disabled
of: correct of_console_check()'s return value
If adapter->dev.parent == NULL there is a NULL pointer dereference in
acpi_i2c_install_space_handler and acpi_i2c_remove_space_handler.
This is present since introduction of this code:
366047515c "i2c: rework kernel config I2C_ACPI" or even
da3c6647ee "I2C/ACPI: Clean up I2C ACPI code and Add CONFIG_I2C_ACPI"
The adapter->dev.parent == NULL case is valid for the i2c_stub,
so loading i2c_stub with ACPI_I2C_OPREGION enabled results in an oops.
This is also valid at least for i2c_tiny_usb and i2c_robotfuzz_osif.
Fix by checking whether it is null before calling ACPI_HANDLE.
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Commit 5d98e61d33 ("I2C/ACPI: Add i2c ACPI operation region support")
renamed the i2c-core module. This may cause regressions for
distributions, so put the ACPI code back into the core.
Reported-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Tested-by: Lan Tianyu <tianyu.lan@intel.com>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
In cases where board has below memory DT node
memory{
device_type = "memory";
reg = <0x80000000 0x80000000>;
};
Check on the memory range in fdt.c will always fail because it is
comparing MAX_PHYS_ADDR with base + size, in fact it should compare
it with base + size - 1.
This issue was originally noticed on Qualcomm IFC6410 board.
Without this patch kernel shows up noticed unnecessary warnings
[ 0.000000] Machine model: Qualcomm APQ8064/IFC6410
[ 0.000000] Ignoring memory range 0xffffffff - 0x100000000
[ 0.000000] cma: Reserved 64 MiB at ab800000
as a result the size get reduced to 0x7fffffff which looks wrong.
This patch fixes the check involved in generating this warning and
as a result it also fixes the wrong size calculation.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
[grant.likely: adjust new size calculation also]
Signed-off-by: Grant Likely <grant.likely@linaro.org>
We need to add this module to the nomux table to be able to detect the
touchpad.
Cc: stablevger.kernel.org
Signed-off-by: Marcos Paulo de Souza <marcos.souza.org@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull drm fixes from Dave Airlie:
"Some final radeon and i915 fixes, black screens mostly"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/radeon/cik: use a separate counter for CP init timeout
drm/i915/hdmi: fix hdmi audio state readout
drm/i915: Don't leak command parser tables on suspend/resume
drm/radeon: add PX quirk for asus K53TK
drm/radeon: add a backlight quirk for Amilo Xi 2550
drm/radeon: add a module parameter for backlight control (v2)
drm/radeon: Update IH_RB_RPTR register after each processed interrupt
drm/radeon: Make IH ring overflow debugging output more useful
drm/radeon: Clear RB_OVERFLOW bit earlier
Fix code when the operation region callback is for an gpio, which
is not at index 0 and for partial pins in a GPIO definition.
For example:
Name (GMOD, ResourceTemplate ()
{
//3 Outputs that define the Power mode of the device
GpioIo (Exclusive, PullDown, , , , "\\_SB.GPI2") {10, 11, 12}
})
}
If opregion callback calls is for:
- Set pin 10, then address = 0 and bit length = 1
- Set pin 11, then address = 1 and bit length = 1
- Set for both pin 11 and pin 12, then address = 1, bit length = 2
This change requires updated ACPICA gpio operation handler code to
send the pin index and bit length.
Fixes: 473ed7be0d (gpio / ACPI: Add support for ACPI GPIO operation regions)
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Cc: 3.15+ <stable@vger.kernel.org> # 3.15+: 75ec6e55f1 ACPICA: Update to GPIO region handler interface.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Changes to correct several GPIO issues:
1) The update_rule in a GPIO field definition is now ignored;
a read-modify-write operation is never performed for GPIO fields.
(Internally, this means that the field assembly/disassembly
code is completely bypassed for GPIO.)
2) The Address parameter passed to a GPIO region handler is
now the bit offset of the field from a previous Connection()
operator. Thus, it becomes a "Pin Number Index" into the
Connection() resource descriptor.
3) The bit_width parameter passed to a GPIO region handler is
now the exact bit width of the GPIO field. Thus, it can be
interpreted as "number of pins".
Overall, we can now say that the region handler interface
to GPIO handlers is a raw "bit/pin" addressed interface, not
a byte-addressed interface like the system_memory handler interface.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Cc: 3.15+ <stable@vger.kernel.org> # 3.15+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
- fix a backlight regression resulting in dark screen
- add a PX quirk to avoid a hang with runtime pm
- fix an init issue on the CIK compute rings
- fix IH ring buffer overflows gracefully
* 'drm-fixes-3.17' of git://people.freedesktop.org/~agd5f/linux:
drm/radeon/cik: use a separate counter for CP init timeout
drm/radeon: add PX quirk for asus K53TK
drm/radeon: add a backlight quirk for Amilo Xi 2550
drm/radeon: add a module parameter for backlight control (v2)
drm/radeon: Update IH_RB_RPTR register after each processed interrupt
drm/radeon: Make IH ring overflow debugging output more useful
drm/radeon: Clear RB_OVERFLOW bit earlier
On some systems (Asus T100 in particular) there are strict ordering
dependencies between LPSS devices with respect to power management
that break if they suspend/resume asynchronously.
In theory it should be possible to follow those dependencies in the
async suspend/resume case too (the ACPI tables tell as that the
dependencies are there), but since we're missing infrastructure
for that at the moment, disable async suspend/resume for all of
the LPSS devices for the time being.
Link: http://marc.info/?l=linux-acpi&m=141158962321905&w=2
Fixes: 8ce62f85a8 (ACPI / platform / LPSS: Enable async suspend/resume of LPSS devices)
Signed-off-by: Li Aubrey <aubrey.li@linux.intel.com>
Signed-off-by: Fu Zhonghui <zhonghui.fu@linux.intel.com>
Cc: 3.16+ <stable@vger.kernel.org> # 3.16+
[ rjw: Changelog ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Pull networking fixes from David Miller:
"Here is a quick pull request primarily meant to address the deconfig
fallout from changing SCSI_NETLINK from being used via 'select' to
being used via 'depends'.
I applied a set of 5 patches written by Michal Marek, and then I
carefully audited all of the remaining config files, basically:
1) I scanned every arch config file, and if it mentioned CONFIG_INET
or CONFIG_UNIX, I made sure it had CONFIG_NET=y
2) After that, I scanned every arch config file, and if it did not
have CONFIG_NET=y I made sure it did not reference any networking
config options.
Finally, we have some late breaking wireless fixes in here from John
Linville and co"
[ And there's a sparc bpf fix snuck in too ]
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
sparc: bpf_jit: fix loads from negative offsets
parisc: Update defconfigs which were missing CONFIG_NET.
powerpc: Update defconfigs which were missing CONFIG_NET.
s390: Update defconfigs which were missing CONFIG_NET.
mips: Update some more defconfigs which were missing CONFIG_NET.
sparc: Set CONFIG_NET=y in defconfigs
sh: Set CONFIG_NET=y in defconfigs
powerpc: Set CONFIG_NET=y in defconfigs
parisc: Set CONFIG_NET=y in defconfigs
mips: Set CONFIG_NET=y in defconfigs
brcmfmac: Fix off by one bug in brcmf_count_20mhz_channels()
ath9k: Fix NULL pointer dereference on early irq
net: rfkill: gpio: Fix clock status
NFC: st21nfca: Fix potential depmod dependency cycle
NFC: st21nfcb: Fix depmod dependency cycle
NFC: microread: Potential overflows in microread_target_discovered()
John W. Linville says:
====================
pull request: wireless 2014-09-23
Please consider pulling this one last batch of fixes intended for the 3.17 stream!
For the NFC bits, Samuel says:
"Hopefully not too late for a handful of NFC fixes:
- 2 potential build failures for ST21NFCA and ST21NFCB, triggered by a
depmod dependenyc cycle.
- One potential buffer overflow in the microread driver."
On top of that...
Emil Goode provides a fix for a brcmfmac off-by-one regression which
was introduced in the 3.17 cycle.
Loic Poulain fixes a polarity mismatch for a variable assignment
inside of rfkill-gpio.
Wojciech Dubowik prevents a NULL pointer dereference in ath9k.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull PCI fixes from Bjorn Helgaas:
"Here are a few fixes that should be in v3.17.
- Reverting "Don't scan random busses" covers up a CardBus regression
having to do with allocating CardBus bus numbers.
- Reverting "Make sure bus numbers stay within parents bounds" covers
up an ACPI _CRS bug that makes us reconfigure a bridge, causing a
broken device behind it to stop responding.
- The pciehp timeout change fixes some code we added in v3.17.
Without the fix, we can send a new hotplug command too early,
before the timeout has expired.
I hope for better fixes for the reverts, but those will have to come
after v3.17"
* tag 'pci-v3.17-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI: pciehp: Fix pcie_wait_cmd() timeout
Revert "PCI: Make sure bus number resources stay within their parents bounds"
Revert "PCI: Don't scan random busses in pci_scan_bridge()"
Pull crypto fixes from Herbert Xu:
"This fixes three issues:
- if ccp is loaded on a machine without ccp, it will incorrectly
activate causing all requests to fail. Fixed by preventing ccp
from loading if hardware isn't available.
- not all IRQs were enabled for the qat driver, leading to potential
stalls when it is used
- disabled buggy AVX CTR implementation in aesni"
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: aesni - disable "by8" AVX CTR optimization
crypto: ccp - Check for CCP before registering crypto algs
crypto: qat - Enable all 32 IRQs
Pull media fixes from Mauro Carvalho Chehab:
"For some last time fixes:
- a regression detected on Kernel 3.16 related to VBI Teletext
application breakage on drivers using videobuf2 (see
https://bugzilla.kernel.org/show_bug.cgi?id=84401). The bug was
noticed on saa7134 (migrated to VB2 on 3.16), but also affects
em28xx (migrated on 3.9 to VB2);
- two additional sanity checks at videobuf2;
- two fixups to restore proper VBI support at the em28xx driver;
- two Kernel oops fixups (at cx24123 and cx2341x drivers);
- a bug at adv7604 where an if was doing just the opposite as it
would be expected;
- some documentation fixups to match the behavior defined at the
Kernel"
* tag 'media/v3.17-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
[media] em28xx-v4l: get rid of field "users" in struct em28xx_v4l2"
[media] em28xx: fix VBI handling logic
[media] DocBook media: improve the poll() documentation
[media] DocBook media: fix the poll() 'no QBUF' documentation
[media] vb2: fix VBI/poll regression
[media] cx2341x: fix kernel oops
[media] cx24123: fix kernel oops due to missing parent pointer
[media] adv7604: fix inverted condition
[media] media/radio: fix radio-miropcm20.c build with io.h header file
[media] vb2: fix plane index sanity check in vb2_plane_cookie()
[media] DocBook media: update version number and V4L2 changes
[media] DocBook media: fix fieldname in struct v4l2_subdev_selection
[media] vb2: fix vb2 state check when start_streaming fails
[media] videobuf2-core.h: fix comment
[media] videobuf2-core: add comments before the WARN_ON
[media] videobuf2-dma-sg: fix for wrong GFP mask to sg_alloc_table_from_pages
Pull bugfixes for md/raid1 from Neil Brown:
"It is amazing how much easier it is to find bugs when you know one is
there. Two bug reports resulted in finding 7 bugs!
All are tagged for -stable. Those that can't cause (rare) data
corruption, cause lockups.
Particularly, but not only, fixing new "resync" code"
* tag 'md/3.17-more-fixes' of git://git.neil.brown.name/md:
md/raid1: fix_read_error should act on all non-faulty devices.
md/raid1: count resync requests in nr_pending.
md/raid1: update next_resync under resync_lock.
md/raid1: Don't use next_resync to determine how far resync has progressed
md/raid1: make sure resync waits for conflicting writes to complete.
md/raid1: clean up request counts properly in close_sync()
md/raid1: be more cautious where we read-balance during resync.
md/raid1: intialise start_next_window for READ case to avoid hang
There is possibility with misconfigured pins that interrupt occurs instantly
after setting irq_set_chained_handler() in gpiochip_set_chained_irqchip().
Now if handler gets called before irq_set_handler_data() the handler gets
NULL handler data.
Fix this by moving irq_set_handler_data() call before
irq_set_chained_handler() in gpiochip_set_chained_irqchip().
Cc: Stable <stable@vger.kernel.org> # 3.15+
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
If the ccp is built as a built-in module, then ccp-crypto (whether
built as a module or a built-in module) will be able to load and
it will register its crypto algorithms. If the system does not have
a CCP this will result in -ENODEV being returned whenever a command
is attempted to be queued by the registered crypto algorithms.
Add an API, ccp_present(), that checks for the presence of a CCP
on the system. The ccp-crypto module can use this to determine if it
should register it's crypto alogorithms.
Cc: stable@vger.kernel.org
Reported-by: Scot Doyle <lkml14@scotdoyle.com>
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Tested-by: Scot Doyle <lkml14@scotdoyle.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
since commit 31964ffebb ("tty: serial: msm: Remove direct access to GSBI")'
serial hangs if earlyprintk are enabled.
This hang is noticed only when the GSBI driver is probed and all the
earlyprintks before gsbi probe are seen on the console.
The reason why it hangs is because GSBI driver disables hclk in its
probe function without realizing that the serial IP might be in use by
a bootconsole. As gsbi driver disables the clock in probe the
bootconsole locks up.
Turning off hclk's could be dangerous if there are system components
like earlyprintk using the hclk.
This patch fixes the issue by delegating the clock management to
probe and remove functions in gsbi rather than disabling the clock in probe.
More detailed problem description can be found here:
http://www.spinics.net/lists/linux-arm-msm/msg10589.html
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Pull infiniband/rdma fixes from Roland Dreier:
"Last late set of InfiniBand/RDMA fixes for 3.17:
- fixes for the new memory region re-registration support
- iSER initiator error path fixes
- grab bag of small fixes for the qib and ocrdma hardware drivers
- larger set of fixes for mlx4, especially in RoCE mode"
* tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (26 commits)
IB/mlx4: Fix VF mac handling in RoCE
IB/mlx4: Do not allow APM under RoCE
IB/mlx4: Don't update QP1 in native mode
IB/mlx4: Avoid accessing netdevice when building RoCE qp1 header
mlx4: Fix mlx4 reg/unreg mac to work properly with 0-mac addresses
IB/core: When marshaling uverbs path, clear unused fields
IB/mlx4: Avoid executing gid task when device is being removed
IB/mlx4: Fix lockdep splat for the iboe lock
IB/mlx4: Get upper dev addresses as RoCE GIDs when port comes up
IB/mlx4: Reorder steps in RoCE GID table initialization
IB/mlx4: Don't duplicate the default RoCE GID
IB/mlx4: Avoid null pointer dereference in mlx4_ib_scan_netdevs()
IB/iser: Bump version to 1.4.1
IB/iser: Allow bind only when connection state is UP
IB/iser: Fix RX/TX CQ resource leak on error flow
RDMA/ocrdma: Use right macro in query AH
RDMA/ocrdma: Resolve L2 address when creating user AH
mlx4: Correct error flows in rereg_mr
IB/qib: Correct reference counting in debugfs qp_stats
IPoIB: Remove unnecessary port query
...
Pull parisc fixes from Helge Deller:
"We avoid using -mfast-indirect-calls for 64bit kernel builds to
prevent building an unbootable kernel due to latest gcc changes.
In the pdc_stable/firmware-access driver we fix a few possible stack
overflows and we now call secure_computing_strict() instead of
secure_computing() which fixes upcoming SECCOMP patches in the
for-next trees"
* 'parisc-3.17-7' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: Only use -mfast-indirect-calls option for 32-bit kernel builds
parisc: pdc_stable.c: Avoid potential stack overflows
parisc: pdc_stable.c: Cleaning up unnecessary use of memset in conjunction with strncpy
parisc: ptrace: use secure_computing_strict()
This reverts commit f23cf8bd5c ("efi/x86: efistub: Move shared
dependencies to <asm/efi.h>") as well as the x86 parts of commit
f4f75ad574 ("efi: efistub: Convert into static library").
The road leading to these two reverts is long and winding.
The above two commits were merged during the v3.17 merge window and
turned the common EFI boot stub code into a static library. This
necessitated making some symbols global in the x86 boot stub which
introduced new entries into the early boot GOT.
The problem was that we weren't fixing up the newly created GOT entries
before invoking the EFI boot stub, which sometimes resulted in hangs or
resets. This failure was reported by Maarten on his Macbook pro.
The proposed fix was commit 9cb0e39423 ("x86/efi: Fixup GOT in all
boot code paths"). However, that caused issues for Linus when booting
his Sony Vaio Pro 11. It was subsequently reverted in commit
f3670394c2.
So that leaves us back with Maarten's Macbook pro not booting.
At this stage in the release cycle the least risky option is to revert
the x86 EFI boot stub to the pre-merge window code structure where we
explicitly #include efi-stub-helper.c instead of linking with the static
library. The arm64 code remains unaffected.
We can take another swing at the x86 parts for v3.18.
Conflicts:
arch/x86/include/asm/efi.h
Tested-by: Josh Boyer <jwboyer@fedoraproject.org>
Tested-by: Maarten Lankhorst <maarten.lankhorst@canonical.com>
Tested-by: Leif Lindholm <leif.lindholm@linaro.org> [arm64]
Tested-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>,
Cc: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Pull hwmon fixes from Guenter Roeck:
- Fix a resource leak in tmp103 driver
- Add support for two more processors to fam15h_power driver
- Also fix a bug in the same driver to only report the power level on
chips which actually support reporting it
* tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (tmp103) Fix resource leak bug in tmp103 temperature sensor driver
hwmon: (fam15h_power) Add support for two more processors
hwmon: (fam15h_power) Make actual power reporting conditional
In the brcmf_count_20mhz_channels function we are looping through a list
of channels received from firmware. Since the index of the first channel
is 0 the condition leads to an off by one bug. This is causing us to hit
the WARN_ON_ONCE(1) calls in the brcmu_d11n_decchspec function, which is
how I discovered the bug.
Introduced by:
commit b48d891676
("brcmfmac: rework wiphy structure setup")
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Emil Goode <emilgoode@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the audio stream is paused or suspended we stop the sDMA and when it
is unpaused/resumed we start the channel without reconfiguring it.
The omap_dma_stop() clears the link configuration when we pause the dma, but
it is not setting it back on start. This will result only one audio buffer
to be played back and the DMA will stop, since the linking is disabled.
We need to restore the CLINK_CTRL register in case of resume.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Add mb() call to resume path to ensure the necessary barrier.
Resume can happen after waking up from suspend for example.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Ring init and cleanup are not balanced because we re-init the rings on
resume without having cleaned them up on suspend. This leads to the
driver leaking the parser's hash tables with a kmemleak signature such
as this:
unreferenced object 0xffff880405960980 (size 32):
comm "systemd-udevd", pid 516, jiffies 4294896961 (age 10202.044s)
hex dump (first 32 bytes):
d0 85 46 c0 ff ff ff ff 00 00 00 00 00 00 00 00 ..F.............
98 60 28 04 04 88 ff ff 00 00 00 00 00 00 00 00 .`(.............
backtrace:
[<ffffffff81816f9e>] kmemleak_alloc+0x4e/0xb0
[<ffffffff811fa678>] kmem_cache_alloc_trace+0x168/0x2f0
[<ffffffffc03e20a5>] i915_cmd_parser_init_ring+0x2a5/0x3e0 [i915]
[<ffffffffc04088a2>] intel_init_ring_buffer+0x202/0x470 [i915]
[<ffffffffc040c998>] intel_init_vebox_ring_buffer+0x1e8/0x2b0 [i915]
[<ffffffffc03eff59>] i915_gem_init_hw+0x2f9/0x3a0 [i915]
[<ffffffffc03f0057>] i915_gem_init+0x57/0x1d0 [i915]
[<ffffffffc045e26a>] i915_driver_load+0xc0a/0x10e0 [i915]
[<ffffffffc02e0d5d>] drm_dev_register+0xad/0x100 [drm]
[<ffffffffc02e3b9f>] drm_get_pci_dev+0x8f/0x200 [drm]
[<ffffffffc03c934b>] i915_pci_probe+0x3b/0x60 [i915]
[<ffffffff81436725>] local_pci_probe+0x45/0xa0
[<ffffffff81437a69>] pci_device_probe+0xd9/0x130
[<ffffffff81524f4d>] driver_probe_device+0x12d/0x3e0
[<ffffffff815252d3>] __driver_attach+0x93/0xa0
[<ffffffff81522e1b>] bus_for_each_dev+0x6b/0xb0
This patch extends the current convention of checking whether a
resource is already allocated before allocating it during ring init.
Longer term it might make sense to only init the rings once.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=83794
Tested-by: Kari Suvanto <kari.tj.suvanto@gmail.com>
Signed-off-by: Brad Volkin <bradley.d.volkin@intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: stable@vger.kernel.org
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
pcie_poll_cmd() take msecs instead of jiffies, so convert timeout to msecs.
Fixes: 40b960831c ("PCI: pciehp: Compute timeout from hotplug command start time")
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Pull networking fixes from David Miller:
1) If the user gives us a msg_namelen of 0, don't try to interpret
anything pointed to by msg_name. From Ani Sinha.
2) Fix some bnx2i/bnx2fc randconfig compilation errors.
The gist of the issue is that we firstly have drivers that span both
SCSI and networking. And at the top of that chain of dependencies
we have things like SCSI_FC_ATTRS and SCSI_NETLINK which are
selected.
But since select is a sledgehammer and ignores dependencies,
everything to select's SCSI_FC_ATTRS and/or SCSI_NETLINK has to also
explicitly select their dependencies and so on and so forth.
Generally speaking 'select' is supposed to only be used for child
nodes, those which have no dependencies of their own. And this
whole chain of dependencies in the scsi layer violates that rather
strongly.
So just make SCSI_NETLINK depend upon it's dependencies, and so on
and so forth for the things selecting it (either directly or
indirectly).
From Anish Bhatt and Randy Dunlap.
3) Fix generation of blackhole routes in IPSEC, from Steffen Klassert.
4) Actually notice netdev feature changes in rtl_open() code, from
Hayes Wang.
5) Fix divide by zero in bond enslaving, from Nikolay Aleksandrov.
6) Missing memory barrier in sunvnet driver, from David Stevens.
7) Don't leave anycast addresses around when ipv6 interface is
destroyed, from Sabrina Dubroca.
8) Don't call efx_{arch}_filter_sync_rx_mode before addr_list_lock is
initialized in SFC driver, from Edward Cree.
9) Fix missing DMA error checking in 3c59x, from Neal Horman.
10) Openvswitch doesn't emit OVS_FLOW_CMD_NEW notifications accidently,
fix from Samuel Gauthier.
11) pch_gbe needs to select NET_PTP_CLASSIFY otherwise we can get a
build error.
12) Fix macvlan regression wherein we stopped emitting
broadcast/multicast frames over software devices. From Nicolas
Dichtel.
13) Fix infiniband bug due to unintended overflow of skb->cb[], from
Eric Dumazet. And add an assertion so this doesn't happen again.
14) dm9000_parse_dt() should return error pointers, not NULL. From
Tobias Klauser.
15) IP tunneling code uses this_cpu_ptr() in preemptible contexts, fix
from Eric Dumazet.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (87 commits)
net: bcmgenet: call bcmgenet_dma_teardown in bcmgenet_fini_dma
net: bcmgenet: fix TX reclaim accounting for fragments
ipv4: do not use this_cpu_ptr() in preemptible context
dm9000: Return an ERR_PTR() in all error conditions of dm9000_parse_dt()
r8169: fix an if condition
r8152: disable ALDPS
ipoib: validate struct ipoib_cb size
net: sched: shrink struct qdisc_skb_cb to 28 bytes
tg3: Work around HW/FW limitations with vlan encapsulated frames
macvlan: allow to enqueue broadcast pkt on virtual device
pch_gbe: 'select' NET_PTP_CLASSIFY.
scsi: Use 'depends' with LIBFC instead of 'select'.
openvswitch: restore OVS_FLOW_CMD_NEW notifications
genetlink: add function genl_has_listeners()
lib: rhashtable: remove second linux/log2.h inclusion
net: allow macvlans to move to net namespace
3c59x: Fix bad offset spec in skb_frag_dma_map
3c59x: Add dma error checking and recovery
sparc: bpf_jit: fix support for ldx/stx mem and SKF_AD_VLAN_TAG
can: at91_can: add missing prepare and unprepare of the clock
...
Pull clock layer fixes from Mike Turquette:
"The fixes for the clock tree are mostly run-time bugs in clock
drivers.
The fixes for TI DRA7 remove divide-by-zero errors. The recently
merged AT91 clock driver fixes some bad error checking and the QCOM
driver fix restores audio for that platform, a clear regression. A
list iteration bug in the framework core was hit recently and is fixed
up here. Finally a compilation warning is fixed for efm32gg, which is
also a regression fix"
* tag 'clk-fixes-for-linus' of git://git.linaro.org/people/mike.turquette/linux:
clk/efm32gg: fix dt init prototype
clk: prevent erronous parsing of children during rate change
clk: rockchip: Fix the clocks for i2c1 and i2c2
clk: qcom: Fix sdc 144kHz frequency entry
clk: at91: fix num_parents test in at91sam9260 slow clk implementation
clk: ti: dra7-atl: Provide error check for incoming parameters in set_rate
clk: ti: divider: Provide error check for incoming parameters in set_rate
We should not be manipulaging the DMA_CTRL registers directly by writing
0 to them to disable DMA. This is an operation that needs to be timed to
make sure the DMA engines have been properly stopped since their state
machine stops on a packet boundary, not immediately.
Make sure that tha bcmgenet_fini_dma() calls bcmgenet_dma_teardown() to
ensure a proper DMA engine state. As a result, we need to reorder the
function bodies to resolve the use dependency.
Fixes: 1c1008c793 ("net: bcmgenet: add main driver file")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The GENET driver supports SKB fragments, and succeeds in transmitting
them properly, but when reclaiming these transmitted fragments, we will
only update the count of free buffer descriptors by 1, even for SKBs
with fragments. This leads to the networking stack thinking it has more
room than the hardware has when pushing new SKBs, and backing off
consequently because we return NETDEV_TX_BUSY.
Fix this by accounting for the SKB nr_frags plus one (itself) and update
ring->free_bds accordingly with that value for each iteration loop in
__bcmgenet_tx_reclaim().
Fixes: 1c1008c793 ("net: bcmgenet: add main driver file")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
