The commit a43ac325c7 ("PCI: Set up bridge resources earlier") moved
bridge window resources set up earlier than before. The change was
necessary to support another change that got pulled on the last minute
due to breaking s390 and other systems.
The presence of valid bridge window resources earlier than before allows
pci_assign_unassigned_root_bus_resources() call from pci_host_probe()
assign the bridge windows. Some host bridges, however, have to wait first
for the link up event before they can enumerate successfully (see e.g.
qcom_pcie_global_irq_thread()) and thus the bus has not been enumerated yet
while calling pci_host_probe().
Calling pci_assign_unassigned_root_bus_resources() without results from
enumeration can result in sizing bridge windows with too small sizes which
cannot be later corrected after the enumeration has completed because
bridge windows have become pinned in place by the other resources.
Interestingly, it seems pci_read_bridge_bases() is not called at all in the
problematic case and the bridge window resource type setup is done by
pci_bridge_check_ranges() and sizing by the usual resource fitting logic.
The root problem behind all this looks pretty generic. If resource fitting
is called too early, the hotplug reservation and old size lower bounding
cause the bridge windows to be assigned without children but with non-zero
size, which leads to these pinning problems. As such, this can likely be
solved on the general level but the solution does not look trivial.
As the commit a43ac325c7 ("PCI: Set up bridge resources earlier") was
prequisite for other change that did not end up into kernel yet, revert it
to resolve the resource assignment failures and give time to code and test
a generic solution.
Fixes: a43ac325c7 ("PCI: Set up bridge resources earlier")
Reported-by: Val Packett <val@packett.cool>
Link: https://lore.kernel.org/r/017ff8df-511c-4da8-b3cf-edf2cb7f1a67@packett.cool
Reported-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/df266709-a9b3-4fd8-af3a-c22eb3c9523a@roeck-us.net
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://patch.msgid.link/20251014163602.17138-1-ilpo.jarvinen@linux.intel.com
Pull pci fix from Bjorn Helgaas:
- Fix a resource lookup regression that broke enumeration of hotplugged
Thunderbolt devices on several platforms (Yangyu Chen)
* tag 'pci-v6.18-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci:
PCI: Fix regression in pci_bus_distribute_available_resources()
The refactoring in 4292a1e45f ("PCI: Refactor distributing available
memory to use loops") switched pci_bus_distribute_available_resources() to
operate on an array of bridge windows. That accidentally looked up bus
resources via pci_bus_resource_n() and then passed those pointers to helper
routines that expect the resource to belong to the device. As soon as we
execute that code, pci_resource_num() warned because the resource wasn't in
the bridge's resource array.
This happens on my AMD Strix Halo machine with Thunderbolt device; the
error message is shown below:
WARNING: CPU: 6 PID: 272 at drivers/pci/pci.h:471 pci_bus_distribute_available_resources+0x6ad/0x6d0
CPU: 6 UID: 0 PID: 272 Comm: irq/33-pciehp Not tainted 6.17.0+ #1 PREEMPT(voluntary)
Hardware name: PELADN YO Series/YO1, BIOS 1.04 05/15/2025
RIP: 0010:pci_bus_distribute_available_resources+0x6ad/0x6d0
Call Trace:
pci_bus_distribute_available_resources+0x590/0x6d0
pci_bridge_distribute_available_resources+0x62/0xb0
pci_assign_unassigned_bridge_resources+0x65/0x1b0
pciehp_configure_device+0x92/0x160
pciehp_handle_presence_or_link_change+0x1b5/0x350
pciehp_ist+0x147/0x1c0
Fix the regression by always fetching the resource directly from the bridge
with pci_resource_n(bridge, PCI_BRIDGE_RESOURCES + i). This restores the
original behaviour while keeping the refactored structure. Then we can
successfully assign resources to the Thunderbolt device.
Fixes: 4292a1e45f ("PCI: Refactor distributing available memory to use loops")
Reported-by: Kenneth R. Crudup <kenny@panix.com>
Closes: https://lore.kernel.org/r/dd551b81-9e81-480b-aab3-7cf8b8bbc1d0@panix.com
Signed-off-by: Yangyu Chen <cyy@cyyself.name>
[bhelgaas: trim timestamps, etc from commit log]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Tested-By: Kenneth R. Crudup <kenny@panix.com>
Link: https://lore.kernel.org/r/F833CC81-7C60-48FC-A31C-B9999DCC6FA2@icloud.com
Link: https://patch.msgid.link/tencent_8C54420E1B0FF8D804C1B4651DF970716309@qq.com
Pull more power management updates from Rafael Wysocki:
"These are cpufreq fixes and cleanups on top of the material merged
previously, a power management core code fix and updates of the
runtime PM framework including unit tests, documentation updates and
introduction of auto-cleanup macros for runtime PM "resume and get"
and "get without resuming" operations.
Specifics:
- Make cpufreq drivers setting the default CPU transition latency to
CPUFREQ_ETERNAL specify a proper default transition latency value
instead which addresses a regression introduced during the 6.6
cycle that broke CPUFREQ_ETERNAL handling (Rafael Wysocki)
- Make the cpufreq CPPC driver use a proper transition delay value
when CPUFREQ_ETERNAL is returned by cppc_get_transition_latency()
to indicate an error condition (Rafael Wysocki)
- Make cppc_get_transition_latency() return a negative error code to
indicate error conditions instead of using CPUFREQ_ETERNAL for this
purpose and drop CPUFREQ_ETERNAL that has no other users (Rafael
Wysocki, Gopi Krishna Menon)
- Fix device leak in the mediatek cpufreq driver (Johan Hovold)
- Set target frequency on all CPUs sharing a policy during frequency
updates in the tegra186 cpufreq driver and make it initialize all
cores to max frequencies (Aaron Kling)
- Rust cpufreq helper cleanup (Thorsten Blum)
- Make pm_runtime_put*() family of functions return 1 when the given
device is already suspended which is consistent with the
documentation (Brian Norris)
- Add basic kunit tests for runtime PM API contracts and update
return values in kerneldoc comments for the runtime PM API (Brian
Norris, Dan Carpenter)
- Add auto-cleanup macros for runtime PM "resume and get" and "get
without resume" operations, use one of them in the PCI core and
drop the existing "free" macro introduced for similar purpose, but
somewhat cumbersome to use (Rafael Wysocki)
- Make the core power management code avoid waiting on device links
marked as SYNC_STATE_ONLY which is consistent with the handling of
those device links elsewhere (Pin-yen Lin)"
* tag 'pm-6.18-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
docs/zh_CN: Fix malformed table
docs/zh_TW: Fix malformed table
PM: runtime: Fix error checking for kunit_device_register()
PM: runtime: Introduce one more usage counter guard
cpufreq: Drop unused symbol CPUFREQ_ETERNAL
ACPI: CPPC: Do not use CPUFREQ_ETERNAL as an error value
cpufreq: CPPC: Avoid using CPUFREQ_ETERNAL as transition delay
cpufreq: Make drivers using CPUFREQ_ETERNAL specify transition latency
PM: runtime: Drop DEFINE_FREE() for pm_runtime_put()
PCI/sysfs: Use runtime PM guard macro for auto-cleanup
PM: runtime: Add auto-cleanup macros for "resume and get" operations
cpufreq: tegra186: Initialize all cores to max frequencies
cpufreq: tegra186: Set target frequency for all cpus in policy
rust: cpufreq: streamline find_supply_names
cpufreq: mediatek: fix device leak on probe failure
PM: sleep: Do not wait on SYNC_STATE_ONLY device links
PM: runtime: Update kerneldoc return codes
PM: runtime: Make put{,_sync}() return 1 when already suspended
PM: runtime: Add basic kunit tests for API contracts
Pull hyperv updates from Wei Liu:
- Unify guest entry code for KVM and MSHV (Sean Christopherson)
- Switch Hyper-V MSI domain to use msi_create_parent_irq_domain()
(Nam Cao)
- Add CONFIG_HYPERV_VMBUS and limit the semantics of CONFIG_HYPERV
(Mukesh Rathor)
- Add kexec/kdump support on Azure CVMs (Vitaly Kuznetsov)
- Deprecate hyperv_fb in favor of Hyper-V DRM driver (Prasanna
Kumar T S M)
- Miscellaneous enhancements, fixes and cleanups (Abhishek Tiwari,
Alok Tiwari, Nuno Das Neves, Wei Liu, Roman Kisel, Michael Kelley)
* tag 'hyperv-next-signed-20251006' of git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux:
hyperv: Remove the spurious null directive line
MAINTAINERS: Mark hyperv_fb driver Obsolete
fbdev/hyperv_fb: deprecate this in favor of Hyper-V DRM driver
Drivers: hv: Make CONFIG_HYPERV bool
Drivers: hv: Add CONFIG_HYPERV_VMBUS option
Drivers: hv: vmbus: Fix typos in vmbus_drv.c
Drivers: hv: vmbus: Fix sysfs output format for ring buffer index
Drivers: hv: vmbus: Clean up sscanf format specifier in target_cpu_store()
x86/hyperv: Switch to msi_create_parent_irq_domain()
mshv: Use common "entry virt" APIs to do work in root before running guest
entry: Rename "kvm" entry code assets to "virt" to genericize APIs
entry/kvm: KVM: Move KVM details related to signal/-EINTR into KVM proper
mshv: Handle NEED_RESCHED_LAZY before transferring to guest
x86/hyperv: Add kexec/kdump support on Azure CVMs
Drivers: hv: Simplify data structures for VMBus channel close message
Drivers: hv: util: Cosmetic changes for hv_utils_transport.c
mshv: Add support for a new parent partition configuration
clocksource: hyper-v: Skip unnecessary checks for the root partition
hyperv: Add missing field to hv_output_map_device_interrupt
Merge runtime PM framework updates and a core power management code fix
for 6.18-rc1:
- Make pm_runtime_put*() family of functions return 1 when the
given device is already suspended which is consistent with the
documentation (Brian Norris)
- Add basic kunit tests for runtime PM API contracts and update return
values in kerneldoc coments for the runtime PM API (Brian Norris,
Dan Carpenter)
- Add auto-cleanup macros for runtime PM "resume and get" and "get
without resume" operations, use one of them in the PCI core and
drop the existing "free" macro introduced for similar purpose, but
somewhat cumbersome to use (Rafael Wysocki)
- Make the core power management code avoid waiting on device links
marked as SYNC_STATE_ONLY which is consistent with the handling of
those device links elsewhere (Pin-yen Lin)
* pm-core:
PM: sleep: Do not wait on SYNC_STATE_ONLY device links
* pm-runtime:
PM: runtime: Fix error checking for kunit_device_register()
PM: runtime: Introduce one more usage counter guard
PM: runtime: Drop DEFINE_FREE() for pm_runtime_put()
PCI/sysfs: Use runtime PM guard macro for auto-cleanup
PM: runtime: Add auto-cleanup macros for "resume and get" operations
PM: runtime: Update kerneldoc return codes
PM: runtime: Make put{,_sync}() return 1 when already suspended
PM: runtime: Add basic kunit tests for API contracts
Pull pci updates from Bjorn Helgaas:
"Enumeration:
- Add PCI_FIND_NEXT_CAP() and PCI_FIND_NEXT_EXT_CAP() macros that
take config space accessor functions.
Implement pci_find_capability(), pci_find_ext_capability(), and
dwc, dwc endpoint, and cadence capability search interfaces with
them (Hans Zhang)
- Leave parent unit address 0 in 'interrupt-map' so that when we
build devicetree nodes to describe PCI functions that contain
multiple peripherals, we can build this property even when
interrupt controllers lack 'reg' properties (Lorenzo Pieralisi)
- Add a Xeon 6 quirk to disable Extended Tags and limit Max Read
Request Size to 128B to avoid a performance issue (Ilpo Järvinen)
- Add sysfs 'serial_number' file to expose the Device Serial Number
(Matthew Wood)
- Fix pci_acpi_preserve_config() memory leak (Nirmoy Das)
Resource management:
- Align m68k pcibios_enable_device() with other arches (Ilpo
Järvinen)
- Remove sparc pcibios_enable_device() implementations that don't do
anything beyond what pci_enable_resources() does (Ilpo Järvinen)
- Remove mips pcibios_enable_resources() and use
pci_enable_resources() instead (Ilpo Järvinen)
- Clean up bridge window sizing and assignment (Ilpo Järvinen),
including:
- Leave non-claimed bridge windows disabled
- Enable bridges even if a window wasn't assigned because not all
windows are required by downstream devices
- Preserve bridge window type when releasing the resource, since
the type is needed for reassignment
- Consolidate selection of bridge windows into two new
interfaces, pbus_select_window() and
pbus_select_window_for_type(), so this is done consistently
- Compute bridge window start and end earlier to avoid logging
stale information
MSI:
- Add quirk to disable MSI on RDC PCI to PCIe bridges (Marcos Del Sol
Vives)
Error handling:
- Align AER with EEH by allowing drivers to request a Bus Reset on
Non-Fatal Errors (in addition to the reset on Fatal Errors that we
already do) (Lukas Wunner)
- If error recovery fails, emit FAILED_RECOVERY uevents for the
devices, not for the bridge leading to them.
This makes them correspond to BEGIN_RECOVERY uevents (Lukas Wunner)
- Align AER with EEH by calling err_handler.error_detected()
callbacks to notify drivers if error recovery fails (Lukas Wunner)
- Align AER with EEH by restoring device error_state to
pci_channel_io_normal before the err_handler.slot_reset() callback.
This is earlier than before the err_handler.resume() callback
(Lukas Wunner)
- Emit a BEGIN_RECOVERY uevent when driver's
err_handler.error_detected() requests a reset, as well as when it
says recovery is complete or can be done without a reset (Niklas
Schnelle)
- Align s390 with AER and EEH by emitting uevents during error
recovery (Niklas Schnelle)
- Align EEH with AER and s390 by emitting BEGIN_RECOVERY,
SUCCESSFUL_RECOVERY, or FAILED_RECOVERY uevents depending on the
result of err_handler.error_detected() (Niklas Schnelle)
- Fix a NULL pointer dereference in aer_ratelimit() when ACPI GHES
error information identifies a device without an AER Capability
(Breno Leitao)
- Update error decoding and TLP Log printing for new errors in
current PCIe base spec (Lukas Wunner)
- Update error recovery documentation to match the current code
and use consistent nomenclature (Lukas Wunner)
ASPM:
- Enable all ClockPM and ASPM states for devicetree platforms, since
there's typically no firmware that enables ASPM
This is a risky change that may uncover hardware or configuration
defects at boot-time rather than when users enable ASPM via sysfs
later. Booting with "pcie_aspm=off" prevents this enabling
(Manivannan Sadhasivam)
- Remove the qcom code that enabled ASPM (Manivannan Sadhasivam)
Power management:
- If a device has already been disconnected, e.g., by a hotplug
removal, don't bother trying to resume it to D0 when detaching the
driver.
This avoids annoying "Unable to change power state from D3cold to
D0" messages (Mario Limonciello)
- Ensure devices are powered up before config reads for
'max_link_width', 'current_link_speed', 'current_link_width',
'secondary_bus_number', and 'subordinate_bus_number' sysfs files.
This prevents using invalid data (~0) in drivers or lspci and,
depending on how the PCIe controller reports errors, may avoid
error interrupts or crashes (Brian Norris)
Virtualization:
- Add rescan/remove locking when enabling/disabling SR-IOV, which
avoids list corruption on s390, where disabling SR-IOV also
generates hotplug events (Niklas Schnelle)
Peer-to-peer DMA:
- Free struct p2p_pgmap, not a member within it, in the
pci_p2pdma_add_resource() error path (Sungho Kim)
Endpoint framework:
- Document sysfs interface for BAR assignment of vNTB endpoint
functions (Jerome Brunet)
- Fix array underflow in endpoint BAR test case (Dan Carpenter)
- Skip endpoint IRQ test if the IRQ is out of range to avoid false
errors (Christian Bruel)
- Fix endpoint test case for controllers with fixed-size BARs smaller
than requested by the test (Marek Vasut)
- Restore inbound translation when disabling doorbell so the endpoint
doorbell test case can be run more than once (Niklas Cassel)
- Avoid a NULL pointer dereference when releasing DMA channels in
endpoint DMA test case (Shin'ichiro Kawasaki)
- Convert tegra194 interrupt number to MSI vector to fix endpoint
Kselftest MSI_TEST test case (Niklas Cassel)
- Reset tegra194 BARs when running in endpoint mode so the BAR tests
don't overwrite the ATU settings in BAR4 (Niklas Cassel)
- Handle errors in tegra194 BPMP transactions so we don't mistakenly
skip future PERST# assertion (Vidya Sagar)
AMD MDB PCIe controller driver:
- Update DT binding example to separate PERST# to a Root Port stanza
to make multiple Root Ports possible in the future (Sai Krishna
Musham)
- Add driver support for PERST# being described in a Root Port
stanza, falling back to the host bridge if not found there (Sai
Krishna Musham)
Freescale i.MX6 PCIe controller driver:
- Enable the 3.3V Vaux supply if available so devices can request
wakeup with either Beacon or WAKE# (Richard Zhu)
MediaTek PCIe Gen3 controller driver:
- Add optional sys clock ready time setting to avoid sys_clk_rdy
signal glitching in MT6991 and MT8196 (AngeloGioacchino Del Regno)
- Add DT binding and driver support for MT6991 and MT8196
(AngeloGioacchino Del Regno)
NVIDIA Tegra PCIe controller driver:
- When asserting PERST#, disable the controller instead of mistakenly
disabling the PLL twice (Nagarjuna Kristam)
- Convert struct tegra_msi mask_lock to raw spinlock to avoid a lock
nesting error (Marek Vasut)
Qualcomm PCIe controller driver:
- Select PCI Power Control Slot driver so slot voltage rails can be
turned on/off if described in Root Port devicetree node (Qiang Yu)
- Parse only PCI bridge child nodes in devicetree, skipping unrelated
nodes such as OPP (Operating Performance Points), which caused
probe failures (Krishna Chaitanya Chundru)
- Add 8.0 GT/s and 32.0 GT/s equalization settings (Ziyue Zhang)
- Consolidate Root Port 'phy' and 'reset' properties in struct
qcom_pcie_port, regardless of whether we got them from the Root
Port node or the host bridge node (Manivannan Sadhasivam)
- Fetch and map the ELBI register space in the DWC core rather than
in each driver individually (Krishna Chaitanya Chundru)
- Enable ECAM mechanism in DWC core by setting up iATU with 'CFG
Shift Feature' and use this in the qcom driver (Krishna Chaitanya
Chundru)
- Add SM8750 compatible to qcom,pcie-sm8550.yaml (Krishna Chaitanya
Chundru)
- Update qcom,pcie-x1e80100.yaml to allow fifth PCIe host on Qualcomm
Glymur, which is compatible with X1E80100 but doesn't have the
cnoc_sf_axi clock (Qiang Yu)
Renesas R-Car PCIe controller driver:
- Fix a typo that prevented correct PHY initialization (Marek Vasut)
- Add a missing 1ms delay after PWR reset assertion as required by
the V4H manual (Marek Vasut)
- Assure reset has completed before DBI access to avoid SError (Marek
Vasut)
- Fix inverted PHY initialization check, which sometimes led to
timeouts and failure to start the controller (Marek Vasut)
- Pass the correct IRQ domain to generic_handle_domain_irq() to fix a
regression when converting to msi_create_parent_irq_domain()
(Claudiu Beznea)
- Drop the spinlock protecting the PMSR register - it's no longer
required since pci_lock already serializes accesses (Marek Vasut)
- Convert struct rcar_msi mask_lock to raw spinlock to avoid a lock
nesting error (Marek Vasut)
SOPHGO PCIe controller driver:
- Check for existence of struct cdns_pcie.ops before using it to
allow Cadence drivers that don't need to supply ops (Chen Wang)
- Add DT binding and driver for the SOPHGO SG2042 PCIe controller
(Chen Wang)
STMicroelectronics STM32MP25 PCIe controller driver:
- Update pinctrl documentation of initial states and use in runtime
suspend/resume (Christian Bruel)
- Add pinctrl_pm_select_init_state() for use by stm32 driver, which
needs it during resume (Christian Bruel)
- Add devicetree bindings and drivers for the STMicroelectronics
STM32MP25 in host and endpoint modes (Christian Bruel)
Synopsys DesignWare PCIe controller driver:
- Add support for x16 in devicetree 'num-lanes' property (Konrad
Dybcio)
- Verify that if DT specifies a single IRQ for all eDMA channels, it
is named 'dma' (Niklas Cassel)
TI J721E PCIe driver:
- Add MODULE_DEVICE_TABLE() so driver can be autoloaded (Siddharth
Vadapalli)
- Power controller off before configuring the glue layer so the
controller latches the correct values on power-on (Siddharth
Vadapalli)
TI Keystone PCIe controller driver:
- Use devm_request_irq() so 'ks-pcie-error-irq' is freed when driver
exits with error (Siddharth Vadapalli)
- Add Peripheral Virtualization Unit (PVU), which restricts DMA from
PCIe devices to specific regions of host memory, to the ti,am65
binding (Jan Kiszka)
Xilinx NWL PCIe controller driver:
- Clear bootloader E_ECAM_CONTROL before merging in the new driver
value to avoid writing invalid values (Jani Nurminen)"
* tag 'pci-v6.18-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci: (141 commits)
PCI/AER: Avoid NULL pointer dereference in aer_ratelimit()
MAINTAINERS: Add entry for ST STM32MP25 PCIe drivers
PCI: stm32-ep: Add PCIe Endpoint support for STM32MP25
dt-bindings: PCI: Add STM32MP25 PCIe Endpoint bindings
PCI: stm32: Add PCIe host support for STM32MP25
PCI: xilinx-nwl: Fix ECAM programming
PCI: j721e: Fix incorrect error message in probe()
PCI: keystone: Use devm_request_irq() to free "ks-pcie-error-irq" on exit
dt-bindings: PCI: qcom,pcie-x1e80100: Set clocks minItems for the fifth Glymur PCIe Controller
PCI: dwc: Support 16-lane operation
PCI: Add lockdep assertion in pci_stop_and_remove_bus_device()
PCI/IOV: Add PCI rescan-remove locking when enabling/disabling SR-IOV
PCI: rcar-host: Convert struct rcar_msi mask_lock into raw spinlock
PCI: tegra194: Rename 'root_bus' to 'root_port_bus' in tegra_pcie_downstream_dev_to_D0()
PCI: tegra: Convert struct tegra_msi mask_lock into raw spinlock
PCI: rcar-gen4: Fix inverted break condition in PHY initialization
PCI: rcar-gen4: Assure reset occurs before DBI access
PCI: rcar-gen4: Add missing 1ms delay after PWR reset assertion
PCI: Set up bridge resources earlier
PCI: rcar-host: Drop PMSR spinlock
...
Pull USB / Thunderbolt updates from Greg KH:
"Here is the big set of USB and thunderbolt drivers for 6.18-rc1. It
was another normal development cycle, with lots of the usual drivers
getting updates:
- Thunderbolt driver cleanups and additions
- dwc3 driver updates
- dwc2 driver updates
- typec driver updates
- xhci driver updates and additions
- offload USB engine updates for better power management
- unused tracepoint removals
- usb gadget fixes and updates as more users start to rely on these
drivers instead of the "old" function gadget drivers
- new USB device ids
- other minor driver USB driver updates
- new USB I/O driver framework and driver additions"
The last item, the usb i/o driver, has an i2c and gpio driver added
through this tree. Those drivers were acked by the respective
subsystem maintainers.
All of these have been in linux-next for a while"
* tag 'usb-6.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (132 commits)
usb: vhci-hcd: Prevent suspending virtually attached devices
USB: serial: option: add SIMCom 8230C compositions
thunderbolt: Fix use-after-free in tb_dp_dprx_work
usb: xhci: align PORTSC trace with one-based port numbering
usb: xhci: correct indentation for PORTSC tracing function
usb: xhci: improve TR Dequeue Pointer mask
usb: xhci-pci: add support for hosts with zero USB3 ports
usb: xhci: Update a comment about Stop Endpoint retries
Revert "usb: xhci: Avoid Stop Endpoint retry loop if the endpoint seems Running"
usb: gadget: f_rndis: Refactor bind path to use __free()
usb: gadget: f_ecm: Refactor bind path to use __free()
usb: gadget: f_acm: Refactor bind path to use __free()
usb: gadget: f_ncm: Refactor bind path to use __free()
usb: gadget: Introduce free_usb_request helper
usb: gadget: Store endpoint pointer in usb_request
usb: host: xhci-rcar: Add Renesas RZ/G3E USB3 Host driver support
usb: host: xhci-plat: Add .post_resume_quirk for struct xhci_plat_priv
usb: host: xhci-rcar: Move R-Car reg definitions
dt-bindings: usb: Document Renesas RZ/G3E USB3HOST
usb: gadget: f_fs: Fix epfile null pointer access after ep enable.
...
- Clear bootloader E_ECAM_CONTROL before merging in the new driver value
(Jani Nurminen)
* pci/controller/xilinx-nwl:
PCI: xilinx-nwl: Fix ECAM programming
- Correct the devm_kcalloc() argument order (Alok Tiwari)
- When asserting PERST#, disable the controller instead of mistakenly
disabling the PLL twice (Nagarjuna Kristam)
- Convert struct tegra_msi mask_lock to raw spinlock to avoid a lock
nesting error (Marek Vasut)
- Rename 'root_bus' to 'root_port_bus' for clarity (Manivannan Sadhasivam)
* pci/controller/tegra:
PCI: tegra194: Rename 'root_bus' to 'root_port_bus' in tegra_pcie_downstream_dev_to_D0()
PCI: tegra: Convert struct tegra_msi mask_lock into raw spinlock
PCI: tegra194: Fix duplicate PLL disable in pex_ep_event_pex_rst_assert()
PCI: tegra: Fix devm_kcalloc() argument order for port->phys allocation
- Update pinctrl documentation of initial states and use in runtime
suspend/resume (Christian Bruel)
- Add pinctrl_pm_select_init_state() for use by stm32 driver, which needs
it during resume (Christian Bruel)
- Add devicetree bindings and drivers for the STMicroelectronics STM32MP25
in host and endpoint modes (Christian Bruel)
* pci/controller/stm32:
MAINTAINERS: Add entry for ST STM32MP25 PCIe drivers
PCI: stm32-ep: Add PCIe Endpoint support for STM32MP25
dt-bindings: PCI: Add STM32MP25 PCIe Endpoint bindings
PCI: stm32: Add PCIe host support for STM32MP25
dt-bindings: PCI: Add STM32MP25 PCIe Root Complex bindings
pinctrl: Add pinctrl_pm_select_init_state helper function
Documentation: pinctrl: Describe PM helper functions for standard states.
- Check for existence of struct cdns_pcie.ops before using it to allow
Cadence drivers that don't need to supply ops (Chen Wang)
- Add DT binding and driver for the Sophgo SG2042 PCIe controller (Chen
Wang)
* pci/controller/sophgo:
PCI: sg2042: Add Sophgo SG2042 PCIe driver
PCI: cadence: Check for the existence of cdns_pcie::ops before using it
dt-bindings: pci: Add Sophgo SG2042 PCIe host
- Pass the correct IRQ domain to generic_handle_domain_irq() to fix a
regression when converting to msi_create_parent_irq_domain() (Claudiu
Beznea)
- Drop the spinlock protecting the PMSR register; it's no longer required
since pci_lock already serializes accesses (Marek Vasut)
- Convert struct rcar_msi mask_lock to raw spinlock to avoid a lock nesting
error (Marek Vasut)
* pci/controller/rcar-host:
PCI: rcar-host: Convert struct rcar_msi mask_lock into raw spinlock
PCI: rcar-host: Drop PMSR spinlock
PCI: rcar-host: Pass proper IRQ domain to generic_handle_domain_irq()
- Fix a typo that prevented correct PHY initialization (Marek Vasut)
- Add a missing 1ms delay after PWR reset assertion as required by the V4H
manual (Marek Vasut)
- Assure reset has completed before DBI access to avoid SError (Marek
Vasut)
- Fix inverted PHY initialization check, which sometimes led to timeouts
and failure to start the controller (Marek Vasut)
* pci/controller/rcar-gen4:
PCI: rcar-gen4: Fix inverted break condition in PHY initialization
PCI: rcar-gen4: Assure reset occurs before DBI access
PCI: rcar-gen4: Add missing 1ms delay after PWR reset assertion
PCI: rcar-gen4: Fix PHY initialization
- Select PCI Power Control Slot driver so slot voltage rails can be turned
on/off if described in Root Port device tree node (Qiang Yu)
- Parse only PCI bridge child nodes in device tree, skipping unrelated
nodes such as OPP (Operating Performance Points), which caused probe
failures (Krishna Chaitanya Chundru)
- Add 8.0 GT/s and 32.0 GT/s equalization settings (Ziyue Zhang)
- Fix typo in CURSOR macro names (Ziyue Zhang)
- Consolidate Root Port 'phy' and 'reset' properties in struct
qcom_pcie_port, regardless of whether we got them from the Root Port node
or the host bridge node (Manivannan Sadhasivam)
- Fetch and map the ELBI register space in the DWC core rather than in each
driver individually (Krishna Chaitanya Chundru)
- Enable ECAM mechanism in DWC core by setting up iATU with 'CFG Shift
Feature' and use this in the qcom driver (Krishna Chaitanya Chundru)
* pci/controller/qcom:
PCI: dwc: Support ECAM mechanism by enabling iATU 'CFG Shift Feature'
PCI: qcom: Prepare for the DWC ECAM enablement
PCI: dwc: Prepare the driver for enabling ECAM mechanism using iATU 'CFG Shift Feature'
PCI: dwc: Add support for ELBI resource mapping
PCI: qcom: Move host bridge 'phy' and 'reset' pointers to struct qcom_pcie_port
PCI: qcom: Fix macro typo for CURSOR
PCI: qcom: Add equalization settings for 8.0 GT/s and 32.0 GT/s
PCI: qcom: Restrict port parsing only to PCIe bridge child nodes
PCI: qcom: Select PCI Power Control Slot driver
- Return -ENOMEM directly instead of using dev_err_probe() (Xichao Zhao)
* pci/controller/plda:
PCI: plda: Remove dev_err_probe() when the errno is -ENOMEM
- Add optional sys clock ready time setting to avoid sys_clk_rdy signal
glitching in MT6991 and MT8196 (AngeloGioacchino Del Regno)
- Add DT binding and driver support for MT6991 and MT8196 (AngeloGioacchino
Del Regno)
* pci/controller/mediatek-gen3:
PCI: mediatek-gen3: Add support for MediaTek MT8196 SoC
dt-bindings: PCI: mediatek-gen3: Add support for MT6991/MT8196
PCI: mediatek-gen3: Implement sys clock ready time setting
- Use kcalloc() instead of kzalloc() to avoid potential integer overflow
(Qianfeng Rong)
- Use devm_request_irq() so 'ks-pcie-error-irq' is freed when driver exits
with error (Siddharth Vadapalli)
* pci/controller/keystone:
PCI: keystone: Use devm_request_irq() to free "ks-pcie-error-irq" on exit
PCI: keystone: Use kcalloc() instead of kzalloc()
- Add MODULE_DEVICE_TABLE() so driver can be autoloaded (Siddharth
Vadapalli)
- Power controller off before configuring the glue layer so the controller
latches the correct values on power-on (Siddharth Vadapalli)
- Correct the error message when j721e_pcie_ctrl_init() fails (Alok Tiwari)
* pci/controller/j721e:
PCI: j721e: Fix incorrect error message in probe()
PCI: j721e: Fix programming sequence of "strap" settings
PCI: j721e: Fix module autoloading
- Enable the 3.3V Vaux supply if available so devices can request wakeup
with either Beacon or WAKE# (Richard Zhu)
* pci/controller/imx6:
PCI: imx6: Enable the Vaux supply if available
- Verify that if DT specifies a single IRQ for all eDMA channels, it is
named 'dma' (Niklas Cassel)
- Remove qcom edma.nr_irqs initialization, which is redundant since
dw_pcie_edma_irq_verify() initializes it based on whether the DT contains
'dma' (single IRQ) or 'dmaX' (multiple IRQs) (Niklas Cassel)
* pci/controller/dwc-edma:
PCI: qcom-ep: Remove redundant edma.nr_irqs initialization
PCI: dwc: Verify the single eDMA IRQ in dw_pcie_edma_irq_verify()
- Update DT binding example to separate PERST# to a Root Port stanza to
make multiple Root Ports possible in the future (Sai Krishna Musham)
- Add driver support for Root Port PERST# (Sai Krishna Musham)
* pci/controller/amd-mdb:
PCI: amd-mdb: Add support for PCIe RP PERST# signal handling
dt-bindings: PCI: amd-mdb: Add example usage of reset-gpios for PCIe RP PERST#
- Check for errors returned from pci_epc_get(), which returns IS_ERR(), not
NULL on error (Dan Carpenter)
- Fix pci_endpoint_test_ioctl() array underflow (Dan Carpenter)
- Document sysfs interface for BAR assignment of vNTB endpoint functions
(Jerome Brunet)
- Drop superfluous pci_epc_features initialization for unsupported
features; we only have to mention features that *are* supported (Niklas
Cassel)
- Skip IRQ tests if the IRQ is out of range (Christian Bruel)
- Fix pci-epf-test for controllers with fixed-size BARs smaller than
requested by the test (Marek Vasut)
- Restore inbound translation when disabling doorbell so the doorbell test
case can be run more than once (Niklas Cassel)
- Check for NULL before releasing DMA channels to avoid a NULL pointer
dereference (Shin'ichiro Kawasaki)
- Convert tegra194 interrupt number to MSI vector to fix endpoint Kselftest
MSI_TEST test case (Niklas Cassel)
- Set tegra_pcie_epc_features.msi_capable so the pci_endpoint_test can use
the optimal IRQ type (Niklas Cassel)
- Reset tegra194 BARs when running in endpoint mode so the BAR tests don't
overwrite the ATU settings in BAR4 (Niklas Cassel)
- Handle errors in tegra194 BPMP transactions so we don't mistakenly skip
future PERST# assertion (Vidya Sagar)
* pci/endpoint:
PCI: tegra194: Handle errors in BPMP response
PCI: tegra194: Reset BARs when running in PCIe endpoint mode
PCI: tegra194: Set pci_epc_features::msi_capable to true
PCI: tegra194: Fix broken tegra_pcie_ep_raise_msi_irq()
PCI: endpoint: pci-epf-test: Add NULL check for DMA channels before release
PCI: endpoint: pci-epf-test: Fix doorbell test support
PCI: endpoint: pci-epf-test: Limit PCIe BAR size for fixed BARs
selftests: pci_endpoint: Skip IRQ test if IRQ is out of range.
misc: pci_endpoint_test: Cleanup extra 0 initialization
misc: pci_endpoint_test: Skip IRQ tests if irq is out of range
PCI: endpoint: Drop superfluous pci_epc_features initialization
Documentation: PCI: endpoint: Document BAR assignment
misc: pci_endpoint_test: Fix array underflow in pci_endpoint_test_ioctl()
PCI: endpoint: pci-ep-msi: Fix NULL vs IS_ERR() check in pci_epf_write_msi_msg()
- Simplify __pci_find_next_cap_ttl() by replacing magic numbers with
#defines, extracting fields with FIELD_GET(), etc (Hans Zhang)
- Convert __pci_find_next_cap_ttl() to a PCI_FIND_NEXT_CAP() macro that
takes a config space accessor function so we can also use it in cases
where the usual config accessors aren't available (Hans Zhang)
- Similarly convert pci_find_next_ext_capability() to a
PCI_FIND_NEXT_EXT_CAP() macro (Hans Zhang)
- Implement dwc, dwc endpoint, and cadence capability search interfaces on
top of PCI_FIND_NEXT_CAP() and PCI_FIND_NEXT_EXT_CAP(), replacing the
previous duplicated code (Hans Zhang)
- Search for capabilities in the cadence core instead of hard-coding their
offsets, which are subject to change (Hans Zhang)
* pci/capability-search:
PCI: cadence: Use cdns_pcie_find_*capability() to avoid hardcoding offsets
PCI: cadence: Implement capability search using PCI core APIs
PCI: dwc: ep: Implement capability search using PCI core APIs
PCI: dwc: Implement capability search using PCI core APIs
PCI: Refactor extended capability search into PCI_FIND_NEXT_EXT_CAP()
PCI: Refactor capability search into PCI_FIND_NEXT_CAP()
PCI: Clean up __pci_find_next_cap_ttl() readability
- Add rescan/remove locking when enabling/disabling SR-IOV, which solves
list corruption on s390, where disabling SR-IOV also generates hotplug
events (Niklas Schnelle)
- Add lockdep assertion in pci_stop_and_remove_bus_device() to catch
device removal without appropriate locking (Niklas Schnelle)
* pci/virtualization:
PCI: Add lockdep assertion in pci_stop_and_remove_bus_device()
PCI/IOV: Add PCI rescan-remove locking when enabling/disabling SR-IOV
- Ensure relaxed tail alignment does not increase min_align when computing
bridge window size, to fix a regression (Ilpo Järvinen)
- Fix bridge window size computation to fix a regression for devices with
undefined PCI class, e.g., Samsung [144d:a5a5] (Ilpo Järvinen)
- Fix error handling during resource resize to fix a regression in amdgpu
(Ilpo Järvinen)
- Align m68k pcibios_enable_device() with other arches (Ilpo Järvinen)
- Remove several sparc pcibios_enable_device() implementations that don't
do anything beyond what pci_enable_resources() does (Ilpo Järvinen)
- Remove mips pcibios_enable_resources() and use pci_enable_resources()
instead (Ilpo Järvinen)
- Refactor and simplify find_bus_resource_of_type() (Ilpo Järvinen)
- Claim bridge windows before setting them up (Ilpo Järvinen)
- Disable non-claimed bridge windows so the kernel's view matches the
hardware configuration (Ilpo Järvinen)
- Use pci_release_resource() instead of release_resource() to reduce code
duplication and increase consistency (Ilpo Järvinen)
- Enable bridges even if bridge window assignment fails (Ilpo Järvinen)
- Preserve bridge window resource type flags when assignment fails because
we may need it later (Ilpo Järvinen)
- Add bridge window selection functions to make the selection consistent
across the several places that do this (Ilpo Järvinen)
- Warn if bridge window cannot be released when resizing BAR (Ilpo
Järvinen)
- Set up bridge resources before enumerating children so we can check
whether child resources are inside bridge windows (Ilpo Järvinen)
* pci/resource:
PCI: Set up bridge resources earlier
PCI: Don't print stale information about resource
PCI: Alter misleading recursion to pci_bus_release_bridge_resources()
PCI: Pass bridge window to pci_bus_release_bridge_resources()
PCI: Add pci_setup_one_bridge_window()
PCI: Refactor remove_dev_resources() to use pbus_select_window()
PCI: Refactor distributing available memory to use loops
PCI: Use pbus_select_window_for_type() during mem window sizing
PCI: Use pbus_select_window() in space available checker
PCI: Rename resource variable from r to res
PCI: Use pbus_select_window_for_type() during IO window sizing
PCI: Use pbus_select_window() during BAR resize
PCI: Warn if bridge window cannot be released when resizing BAR
PCI: Fix finding bridge window in pci_reassign_bridge_resources()
PCI: Add bridge window selection functions
PCI: Add defines for bridge window indexing
PCI: Preserve bridge window resource type flags
PCI: Enable bridge even if bridge window fails to assign
PCI: Use pci_release_resource() instead of release_resource()
PCI: Disable non-claimed bridge window
PCI: Always claim bridge window before its setup
PCI: Refactor find_bus_resource_of_type() logic checks
PCI: Move find_bus_resource_of_type() earlier
MIPS: PCI: Use pci_enable_resources()
sparc/PCI: Remove pcibios_enable_device() as they do nothing extra
m68k/PCI: Use pci_enable_resources() in pcibios_enable_device()
PCI: Fix failure detection during resource resize
PCI: Fix pdev_resources_assignable() disparity
PCI: Ensure relaxed tail alignment does not increase min_align
- Fix a double cleanup of regulators if devm_add_action_or_reset() fails
(Geert Uytterhoeven)
* pci/pwrctrl:
PCI/pwrctrl: Fix device leak at device stop
PCI/pwrctrl: Fix device and OF node leak at bus scan
PCI/pwrctrl: Fix device leak at registration
PCI/pwrctrl: Fix double cleanup on devm_add_action_or_reset() failure
- If a device has already been disconnected, e.g., by a hotplug removal,
don't bother trying to resume it to D0 when detaching the driver (Mario
Limonciello)
- Ensure devices are powered up before config reads for 'max_link_width',
'current_link_speed', 'current_link_width', 'secondary_bus_number', and
'subordinate_bus_number' sysfs files (Brian Norris)
* pci/pm:
PCI/sysfs: Ensure devices are powered for config reads
PCI/PM: Skip resuming to D0 if device is disconnected
- Free struct p2p_pgmap, not a member within it, in the
pci_p2pdma_add_resource() error path (Sungho Kim)
- Make pci_has_p2pmem() static (Leon Romanovsky)
* pci/p2pdma:
PCI/P2PDMA: Reduce scope of pci_has_p2pmem()
PCI/P2PDMA: Fix incorrect pointer usage in devm_kfree() call
- Leave parent unit address 0 in 'interrupt-map' so we can build this
property even when interrupt controllers lack 'reg' properties (Lorenzo
Pieralisi)
* pci/of:
PCI: of: Update parent unit address generation in of_pci_prop_intr_map()
- Use PCI_HEADER_TYPE_* defines, not hard-coded values (Ilpo Järvinen)
- Clean up early_dump_pci_device() to avoid hard-coded values (Ilpo
Järvinen)
- Clean up pci_scan_child_bus_extend() loop to avoid hard-coded values
(Ilpo Järvinen)
- Add a Xeon 6 quirk to disable Extended Tags and limit Max Read Request
Size to 128B to avoid a performance issue (Ilpo Järvinen)
* pci/enumeration:
PCI: Add Extended Tag + MRRS quirk for Xeon 6
PCI: Clean up pci_scan_child_bus_extend() loop
PCI: Clean up early_dump_pci_device()
PCI: Use header type defines in pci_setup_device()
- Enable all ClockPM and ASPM states for devicetree platforms, since
there's typically no firmware that enables ASPM (Manivannan Sadhasivam)
- Remove the qcom code that enabled ASPM (Manivannan Sadhasivam)
* pci/aspm:
PCI: qcom: Remove custom ASPM enablement code
PCI/ASPM: Enable all ClockPM and ASPM states for devicetree platforms
Pull drm updates from Dave Airlie:
"cross-subsystem:
- i2c-hid: Make elan touch controllers power on after panel is
enabled
- dt bindings for STM32MP25 SoC
- pci vgaarb: use screen_info helpers
- rust pin-init updates
- add MEI driver for late binding firmware update/load
uapi:
- add ioctl for reassigning GEM handles
- provide boot_display attribute on boot-up devices
core:
- document DRM_MODE_PAGE_FLIP_EVENT
- add vendor specific recovery method to drm device wedged uevent
gem:
- Simplify gpuvm locking
ttm:
- add interface to populate buffers
sched:
- Fix race condition in trace code
atomic:
- Reallow no-op async page flips
display:
- dp: Fix command length
video:
- Improve pixel-format handling for struct screen_info
rust:
- drop Opaque<> from ioctl args
- Alloc:
- BorrowedPage type and AsPageIter traits
- Implement Vmalloc::to_page() and VmallocPageIter
- DMA/Scatterlist:
- Add dma::DataDirection and type alias for dma_addr_t
- Abstraction for struct scatterlist and sg_table
- DRM:
- simplify use of generics
- add DriverFile type alias
- drop Object::SIZE
- Rust:
- pin-init tree merge
- Various methods for AsBytes and FromBytes traits
gpuvm:
- Support madvice in Xe driver
gpusvm:
- fix hmm_pfn_to_map_order usage in gpusvm
bridge:
- Improve and fix ref counting on bridge management
- cdns-dsi: Various improvements to mode setting
- Support Solomon SSD2825 plus DT bindings
- Support Waveshare DSI2DPI plus DT bindings
- Support Content Protection property
- display-connector: Improve DP display detection
- Add support for Radxa Ra620 plus DT bindings
- adv7511: Provide SPD and HDMI infoframes
- it6505: Replace crypto_shash with sha()
- synopsys: Add support for DW DPTX Controller plus DT bindings
- adv7511: Write full Audio infoframe
- ite6263: Support vendor-specific infoframes
- simple: Add support for Realtek RTD2171 DP-to-HDMI plus DT bindings
panel:
- panel-edp: Support mt8189 Chromebooks; Support BOE NV140WUM-N64;
Support SHP LQ134Z1; Fixes
- panel-simple: Support Olimex LCD-OLinuXino-5CTS plus DT bindings
- Support Samsung AMS561RA01
- Support Hydis HV101HD1 plus DT bindings
- ilitek-ili9881c: Refactor mode setting; Add support for Bestar
BSD1218-A101KL68 LCD plus DT bindings
- lvds: Add support for Ampire AMP19201200B5TZQW-T03 to DT bindings
- edp: Add support for additonal mt8189 Chromebook panels
- lvds: Add DT bindings for EDT ETML0700Z8DHA
amdgpu:
- add CRIU support for gem objects
- RAS updates
- VCN SRAM load fixes
- EDID read fixes
- eDP ALPM support
- Documentation updates
- Rework PTE flag generation
- DCE6 fixes
- VCN devcoredump cleanup
- MMHUB client id fixes
- VCN 5.0.1 RAS support
- SMU 13.0.x updates
- Expanded PCIe DPC support
- Expanded VCN reset support
- VPE per queue reset support
- give kernel jobs unique id for tracing
- pre-populate exported buffers
- cyan skillfish updates
- make vbios build number available in sysfs
- userq updates
- HDCP updates
- support MMIO remap page as ttm pool
- JPEG parser updates
- DCE6 DC updates
- use devm for i2c buses
- GPUVM locking updates
- Drop non-DC DCE11 code
- improve fallback handling for pixel encoding
amdkfd:
- SVM/page migration fixes
- debugfs fixes
- add CRIO support for gem objects
- SVM updates
radeon:
- use dev_warn_once in CS parsers
xe:
- add madvise interface
- add DRM_IOCTL_XE_VM_QUERY_MEMORY_RANGE_ATTRS to query VMA count
and memory attributes
- drop L# bank mask reporting from media GT3 on Xe3+.
- add SLPC power_profile sysfs interface
- add configs attribs to add post/mid context-switch commands
- handle firmware reported hardware errors notifying userspace with
device wedged uevent
- use same dir structure across sysfs/debugfs
- cleanup and future proof vram region init
- add G-states and PCI link states to debugfs
- Add SRIOV support for CCS surfaces on Xe2+
- Enable SRIOV PF mode by default on supported platforms
- move flush to common code
- extended core workarounds for Xe2/3
- use DRM scheduler for delayed GT TLB invalidations
- configs improvements and allow VF device enablement
- prep work to expose mmio regions to userspace
- VF migration support added
- prepare GPU SVM for THP migration
- start fixing XE_PAGE_SIZE vs PAGE_SIZE
- add PSMI support for hw validation
- resize VF bars to max possible size according to number of VFs
- Ensure GT is in C0 during resume
- pre-populate exported buffers
- replace xe_hmm with gpusvm
- add more SVM GT stats to debugfs
- improve fake pci and WA kunnit handle for new platform testing
- Test GuC to GuC comms to add debugging
- use attribute groups to simplify sysfs registration
- add Late Binding firmware code to interact with MEI
i915:
- apply multiple JSL/EHL/Gen7/Gen6 workarounds properly
- protect against overflow in active_engine()
- Use try_cmpxchg64() in __active_lookup()
- include GuC registers in error state
- get rid of dev->struct_mutex
- iopoll: generalize read_poll_timout
- lots more display refactoring
- Reject HBR3 in any eDP Panel
- Prune modes for YUV420
- Display Wa fix, additions, and updates
- DP: Fix 2.7 Gbps link training on g4x
- DP: Adjust the idle pattern handling
- DP: Shuffle the link training code a bit
- Don't set/read the DSI C clock divider on GLK
- Enable_psr kernel parameter changes
- Type-C enabled/disconnected dp-alt sink
- Wildcat Lake enabling
- DP HDR updates
- DRAM detection
- wait PSR idle on dsb commit
- Remove FBC modulo 4 restriction for ADL-P+
- panic: refactor framebuffer allocation
habanalabs:
- debug/visibility improvements
- vmalloc-backed coherent mmap support
- HLDIO infrastructure
nova-core:
- various register!() macro improvements
- minor vbios/firmware fixes/refactoring
- advance firmware boot stages; process Booter and patch signatures
- process GSP and GSP bootloader
- Add r570.144 firmware bindings and update to it
- Move GSP boot code to own module
- Use new pin-init features to store driver's private data in a
single allocation
- Update ARef import from sync::aref
nova-drm:
- Update ARef import from sync::aref
tyr:
- initial driver skeleton for a rust driver for ARM Mali GPUs
- capable of powering up, query metadata and provide it to userspace.
msm:
- GPU and Core:
- in DT bindings describe clocks per GPU type
- GMU bandwidth voting for x1-85
- a623/a663 speedbins
- cleanup some remaining no-iommu leftovers after VM_BIND conversion
- fix GEM obj 32b size truncation
- add missing VM_BIND param validation
- IFPC for x1-85 and a750
- register xml and gen_header.py sync from mesa
- Display:
- add missing bindings for display on SC8180X
- added DisplayPort MST bindings
- conversion from round_rate() to determine_rate()
amdxdna:
- add IOCTL_AMDXDNA_GET_ARRAY
- support user space allocated buffers
- streamline PM interfaces
- Refactoring wrt. hardware contexts
- improve error reporting
nouveau:
- use GSP firmware by default
- improve error reporting
- Pre-populate exported buffers
ast:
- Clean up detection of DRAM config
exynos:
- add DSIM bridge driver support for Exynos7870
- Document Exynos7870 DSIM compatible in dt-binding
panthor:
- Print task/pid on errors
- Add support for Mali G710, G510, G310, Gx15, Gx20, Gx25
- Improve cache flushing
- Fail VM bind if BO has offset
renesas:
- convert to RUNTIME_PM_OPS
rcar-du:
- Make number of lanes configurable
- Use RUNTIME_PM_OPS
- Add support for DSI commands
rocket:
- Add driver for Rockchip NPU plus DT bindings
- Use kfree() and sizeof() correctly
- Test DMA status
rockchip:
- dsi2: Add support for RK3576 plus DT bindings
- Add support for RK3588 DPTX output
tidss:
- Use crtc_ fields for programming display mode
- Remove other drivers from aperture
pixpaper:
- Add support for Mayqueen Pixpaper plus DT bindings
v3d:
- Support querying nubmer of GPU resets for KHR_robustness
stm:
- Clean up logging
- ltdc: Add support support for STM32MP257F-EV1 plus DT bindings
sitronix:
- st7571-i2c: Add support for inverted displays and 2-bit grayscale
tidss:
- Convert to kernel's FIELD_ macros
vesadrm:
- Support 8-bit palette mode
imagination:
- Improve power management
- Add support for TH1520 GPU
- Support Risc-V architectures
v3d:
- Improve job management and locking
vkms:
- Support variants of ARGB8888, ARGB16161616, RGB565, RGB888 and P01x
- Spport YUV with 16-bit components"
* tag 'drm-next-2025-10-01' of https://gitlab.freedesktop.org/drm/kernel: (1455 commits)
drm/amd: Add name to modes from amdgpu_connector_add_common_modes()
drm/amd: Drop some common modes from amdgpu_connector_add_common_modes()
drm/amdgpu: update MODULE_PARM_DESC for freesync_video
drm/amd: Use dynamic array size declaration for amdgpu_connector_add_common_modes()
drm/amd/display: Share dce100_validate_global with DCE6-8
drm/amd/display: Share dce100_validate_bandwidth with DCE6-8
drm/amdgpu: Fix fence signaling race condition in userqueue
amd/amdkfd: enhance kfd process check in switch partition
amd/amdkfd: resolve a race in amdgpu_amdkfd_device_fini_sw
drm/amd/display: Reject modes with too high pixel clock on DCE6-10
drm/amd: Drop unnecessary check in amdgpu_connector_add_common_modes()
drm/amd/display: Only enable common modes for eDP and LVDS
drm/amdgpu: remove the redeclaration of variable i
drm/amdgpu/userq: assign an error code for invalid userq va
drm/amdgpu: revert "rework reserved VMID handling" v2
drm/amdgpu: remove leftover from enforcing isolation by VMID
drm/amdgpu: Add fallback to pipe reset if KCQ ring reset fails
accel/habanalabs: add Infineon version check
accel/habanalabs/gaudi2: read preboot status after recovering from dirty state
accel/habanalabs: add HL_GET_P_STATE passthrough type
...
When platform firmware supplies error information to the OS, e.g., via the
ACPI APEI GHES mechanism, it may identify an error source device that
doesn't advertise an AER Capability and therefore dev->aer_info, which
contains AER stats and ratelimiting data, is NULL.
pci_dev_aer_stats_incr() already checks dev->aer_info for NULL, but
aer_ratelimit() did not, leading to NULL pointer dereferences like this one
from the URL below:
{1}[Hardware Error]: Hardware error from APEI Generic Hardware Error Source: 0
{1}[Hardware Error]: event severity: corrected
{1}[Hardware Error]: device_id: 0000:00:00.0
{1}[Hardware Error]: vendor_id: 0x8086, device_id: 0x2020
{1}[Hardware Error]: aer_cor_status: 0x00001000, aer_cor_mask: 0x00002000
BUG: kernel NULL pointer dereference, address: 0000000000000264
RIP: 0010:___ratelimit+0xc/0x1b0
pci_print_aer+0x141/0x360
aer_recover_work_func+0xb5/0x130
[8086:2020] is an Intel "Sky Lake-E DMI3 Registers" device that claims to
be a Root Port but does not advertise an AER Capability.
Add a NULL check in aer_ratelimit() to avoid the NULL pointer dereference.
Note that this also prevents ratelimiting these events from GHES.
Fixes: a57f2bfb4a ("PCI/AER: Ratelimit correctable and non-fatal error logging")
Link: https://lore.kernel.org/r/buduna6darbvwfg3aogl5kimyxkggu3n4romnmq6sozut6axeu@clnx7sfsy457/
Signed-off-by: Breno Leitao <leitao@debian.org>
[bhelgaas: add crash details to commit log]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Cc: stable@vger.kernel.org
Link: https://patch.msgid.link/20250929-aer_crash_2-v1-1-68ec4f81c356@debian.org
Pull devicetree updates from Rob Herring:
"DT core:
- Update dtc to upstream version v1.7.2-35-g52f07dcca47c
- Add stub for of_get_next_child_with_prefix()
- Convert of_msi_map_id() callers to of_msi_xlate()
DT bindings:
- Convert multiple text board bindings to DT schema format
- Add bindings for synaptics,synaptics_i2c touchscreen controller,
innolux,n133hse-ea1 and nlt,nl12880bc20-spwg-24 displays, and NXP
vf610 reboot controller
- Add new Arm Cortex-A320/A520AE/A720AE and C1-Nano/Pro/Premium/Ultra
CPUs. Add missing Applied Micro CPU compatibles. Add pu-supply and
fsl,soc-operating-points properties for CPU nodes.
- Add QCom Glymur PDC and tegra264-agic interrupt controllers
- Add samsung,exynos8890-mali GPU to Arm Mali Midgard
- Drop Samsung S3C2410 display related bindings
- Allow separate DP lane and AUX connections in dp-connector
- Add some missing, undocumented vendor prefixes
- Add missing '#address-cells' properties in interrupt controller
bindings which dtc now warns about
- Drop duplicate socfpga-sdram-edac.txt, moxa,moxart-watchdog.txt,
fsl/mpic.txt, ti,opa362.txt, and cavium-thunder2.txt legacy text
bindings which are already covered by existing schemas.
- Various binding fixes for Mediatek platforms in mailbox, regulator,
pinctrl, timer, and display
- Drop work-around for yamllint quoting of values containing ','
- Various spelling, typo, grammar, and duplicated words fixes in DT
bindings and docs
- Add binding guidelines for defining properties at top level of
schemas, lack of node name ABI, and usage of simple-mfd"
* tag 'devicetree-for-6.18' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (81 commits)
dt-bindings: arm: altera: Drop socfpga-sdram-edac.txt
dt-bindings: gpu: Convert nvidia,gk20a to DT schema
dt-bindings: rng: sparc_sun_oracle_rng: convert to DT schema
dt-bindings: vendor-prefixes: update regex for properties without a prefix
dt-bindings: display: bridge: convert megachips-stdpxxxx-ge-b850v3-fw.txt to yaml
scripts: dt_to_config: fix grammar and a typo in --help text
dt-bindings: fix spelling, typos, grammar, duplicated words
docs: dt: fix grammar and spelling
of: base: Add of_get_next_child_with_prefix() stub
dt-bindings: trivial-devices: Add compatible string synaptics,synaptics_i2c
dt-bindings: soc: mediatek: pwrap: Add power-domains property
dt-bindings: pinctrl: mt65xx: Allow gpio-line-names
dt-bindings: media: Convert MediaTek mt8173-vpu bindings to DT schema
dt-bindings: arm: mediatek: Support mt8183-audiosys variant
dt-bindings: mailbox: mediatek,gce-mailbox: Make clock-names optional
dt-bindings: regulator: mediatek,mt6331: Add missing compatible
dt-bindings: regulator: mediatek,mt6331: Fix various regulator names
dt-bindings: regulator: mediatek,mt6332-regulator: Add missing compatible
dt-bindings: pinctrl: mediatek,mt7622-pinctrl: Add missing base reg
dt-bindings: pinctrl: mediatek,mt7622-pinctrl: Add missing pwm_ch7_2
...
Add driver to configure the STM32MP25 SoC PCIe controller based on the
DesignWare PCIe core in endpoint mode. Controller support 2.5 and 5 GT/s
data rates and uses the common reference clock provided by the host.
The PCIe core_clk receives the pipe0_clk from the ComboPHY as input,
and the ComboPHY PLL must be locked for pipe0_clk to be ready.
Consequently, PCIe core registers cannot be accessed until the ComboPHY is
fully initialised and REFCLK is enabled and ready.
Signed-off-by: Christian Bruel <christian.bruel@foss.st.com>
[mani: reworded description]
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
[bhelgaas: squash in https://patch.msgid.link/20250902122641.269725-1-christian.bruel@foss.st.com
to remove redundant link_status checks]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://patch.msgid.link/20250820075411.1178729-7-christian.bruel@foss.st.com
At present VMBus driver is hinged off of CONFIG_HYPERV which entails
lot of builtin code and encompasses too much. It's not always clear
what depends on builtin hv code and what depends on VMBus. Setting
CONFIG_HYPERV as a module and fudging the Makefile to switch to builtin
adds even more confusion. VMBus is an independent module and should have
its own config option. Also, there are scenarios like baremetal dom0/root
where support is built in with CONFIG_HYPERV but without VMBus. Lastly,
there are more features coming down that use CONFIG_HYPERV and add more
dependencies on it.
So, create a fine grained HYPERV_VMBUS option and update Kconfigs for
dependency on VMBus.
Signed-off-by: Mukesh Rathor <mrathor@linux.microsoft.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com> # drivers/pci
Signed-off-by: Wei Liu <wei.liu@kernel.org>
Pull irq chip driver updates from Thomas Gleixner:
- Use the startup/shutdown callbacks for the PCI/MSI per device
interrupt domains.
This allows us to initialize the RISCV PLIC interrupt hierarchy
correctly and provides a mechanism to decouple the masking and
unmasking during run-time from the expensive PCI mask and unmask when
the underlying MSI provider implementation allows the interrupt to be
masked.
- Initialize the RISCV PLIC MSI interrupt hierarchy correctly so that
the affinity assignment works correctly by switching it over to the
startup/shutdown scheme
- Allow MSI providers to opt out from masking a PCI/MSI interrupt at
the PCI device during operation when the provider can mask the
interrupt at the underlying interrupt chip. This reduces the overhead
in scenarios where disable_irq()/enable_irq() is utilized frequently
by a driver.
The PCI/MSI device level [un]masking is only required on startup and
shutdown in this case.
- Remove the conditional mask/unmask logic in the PCI/MSI layer as this
is now handled unconditionally.
- Replace the hardcoded interrupt routing in the Loongson EIOINTC
interrupt driver to respect the firmware settings and spread them out
to different CPU interrupt inputs so that the demultiplexing handler
only needs to read only a single 64-bit status register instead of
four, which significantly reduces the overhead in VMs as the status
register access causes a VM exit.
- Add support for the new AST2700 SCU interrupt controllers
- Use the legacy interrupt domain setup for the Loongson PCH-LPC
interrupt controller, which resembles the x86 legacy PIC setup and
has the same hardcoded legacy requirements.
- The usual set of cleanups, fixes and improvements all over the place
* tag 'irq-drivers-2025-09-29' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (25 commits)
irqchip/loongson-pch-lpc: Use legacy domain for PCH-LPC IRQ controller
PCI/MSI: Remove the conditional parent [un]mask logic
irqchip/msi-lib: Honor the MSI_FLAG_PCI_MSI_MASK_PARENT flag
irqchip/aspeed-scu-ic: Add support for AST2700 SCU interrupt controllers
dt-bindings: interrupt-controller: aspeed: Add AST2700 SCU IC compatibles
dt-bindings: mfd: aspeed: Add AST2700 SCU compatibles
irqchip/aspeed-scu-ic: Refactor driver to support variant-based initialization
irqchip/gic-v5: Fix error handling in gicv5_its_irq_domain_alloc()
irqchip/gic-v5: Fix loop in gicv5_its_create_itt_two_level() cleanup path
irqchip/gic-v5: Delete a stray tab
irqchip/sg2042-msi: Set irq type according to DT configuration
riscv: sophgo: dts: sg2044: Change msi irq type to IRQ_TYPE_EDGE_RISING
riscv: sophgo: dts: sg2042: Change msi irq type to IRQ_TYPE_EDGE_RISING
irqchip/gic-v2m: Handle Multiple MSI base IRQ Alignment
irqchip/renesas-rzg2l: Remove dev_err_probe() if error is -ENOMEM
irqchip: Use int type to store negative error codes
irqchip/gic-v5: Remove the redundant ITS cache invalidation
PCI/MSI: Check MSI_FLAG_PCI_MSI_MASK_PARENT in cond_[startup|shutdown]_parent()
irqchip/loongson-eiointc: Add multiple interrupt pin routing support
irqchip/loongson-eiointc: Route interrupt parsed from bios table
...
