dev->chipid is used in lan78xx_init_mac_address before it's initialized:
lan78xx_reset() {
lan78xx_init_mac_address()
lan78xx_read_eeprom()
lan78xx_read_raw_eeprom() <- dev->chipid is used here
dev->chipid = ... <- dev->chipid is initialized correctly here
}
Reorder initialization so that dev->chipid is set before calling
lan78xx_init_mac_address().
Fixes: a0db7d10b7 ("lan78xx: Add to handle mux control per chip id")
Signed-off-by: I Viswanath <viswanathiyyappan@gmail.com>
Reviewed-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Reviewed-by: Khalid Aziz <khalid@kernel.org>
Link: https://patch.msgid.link/20251013181648.35153-1-viswanathiyyappan@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The function lan78xx_write_raw_eeprom failed to properly propagate EEPROM
write timeout errors (-ETIMEDOUT). In the timeout fallthrough path, it first
attempted to restore the pin configuration for LED outputs and then
returned only the status of that restore operation, discarding the
original timeout error saved in ret.
As a result, callers could mistakenly treat EEPROM write operation as
successful even though the EEPROM write had actually timed out with no
or partial data write.
To fix this, handle errors in restoring the LED pin configuration separately.
If the restore succeeds, return any prior EEPROM write timeout error saved
in ret to the caller.
Suggested-by: Oleksij Rempel <o.rempel@pengutronix.de>
Fixes: 8b1b2ca83b ("net: usb: lan78xx: Improve error handling in EEPROM and OTP operations")
cc: stable@vger.kernel.org
Signed-off-by: Bhanu Seshu Kumar Valluri <bhanuseshukumar@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prevent USB runtime PM (autosuspend) for AX88772* in bind.
usbnet enables runtime PM (autosuspend) by default, so disabling it via
the usb_driver flag is ineffective. On AX88772B, autosuspend shows no
measurable power saving with current driver (no link partner, admin
up/down). The ~0.453 W -> ~0.248 W drop on v6.1 comes from phylib powering
the PHY off on admin-down, not from USB autosuspend.
The real hazard is that with runtime PM enabled, ndo_open() (under RTNL)
may synchronously trigger autoresume (usb_autopm_get_interface()) into
asix_resume() while the USB PM lock is held. Resume paths then invoke
phylink/phylib and MDIO, which also expect RTNL, leading to possible
deadlocks or PM lock vs MDIO wake issues.
To avoid this, keep the device runtime-PM active by taking a usage
reference in ax88772_bind() and dropping it in unbind(). A non-zero PM
usage count blocks runtime suspend regardless of userspace policy
(.../power/control - pm_runtime_allow/forbid), making this approach
robust against sysfs overrides.
Holding a runtime-PM usage ref does not affect system-wide suspend;
system sleep/resume callbacks continue to run as before.
Fixes: 4a2c7217cd ("net: usb: asix: ax88772: manage PHY PM from MAC")
Reported-by: Hubert Wiśniewski <hubert.wisniewski.25632@gmail.com>
Closes: https://lore.kernel.org/all/DCGHG5UJT9G3.2K1GHFZ3H87T0@gmail.com
Tested-by: Hubert Wiśniewski <hubert.wisniewski.25632@gmail.com>
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Closes: https://lore.kernel.org/all/b5ea8296-f981-445d-a09a-2f389d7f6fdd@samsung.com
Cc: stable@vger.kernel.org
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://patch.msgid.link/20251005081203.3067982-1-o.rempel@pengutronix.de
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Syzbot reported read of uninitialized variable BUG with following call stack.
lan78xx 8-1:1.0 (unnamed net_device) (uninitialized): EEPROM read operation timeout
=====================================================
BUG: KMSAN: uninit-value in lan78xx_read_eeprom drivers/net/usb/lan78xx.c:1095 [inline]
BUG: KMSAN: uninit-value in lan78xx_init_mac_address drivers/net/usb/lan78xx.c:1937 [inline]
BUG: KMSAN: uninit-value in lan78xx_reset+0x999/0x2cd0 drivers/net/usb/lan78xx.c:3241
lan78xx_read_eeprom drivers/net/usb/lan78xx.c:1095 [inline]
lan78xx_init_mac_address drivers/net/usb/lan78xx.c:1937 [inline]
lan78xx_reset+0x999/0x2cd0 drivers/net/usb/lan78xx.c:3241
lan78xx_bind+0x711/0x1690 drivers/net/usb/lan78xx.c:3766
lan78xx_probe+0x225c/0x3310 drivers/net/usb/lan78xx.c:4707
Local variable sig.i.i created at:
lan78xx_read_eeprom drivers/net/usb/lan78xx.c:1092 [inline]
lan78xx_init_mac_address drivers/net/usb/lan78xx.c:1937 [inline]
lan78xx_reset+0x77e/0x2cd0 drivers/net/usb/lan78xx.c:3241
lan78xx_bind+0x711/0x1690 drivers/net/usb/lan78xx.c:3766
The function lan78xx_read_raw_eeprom failed to properly propagate EEPROM
read timeout errors (-ETIMEDOUT). In the fallthrough path, it first
attempted to restore the pin configuration for LED outputs and then
returned only the status of that restore operation, discarding the
original timeout error.
As a result, callers could mistakenly treat the data buffer as valid
even though the EEPROM read had actually timed out with no data or partial
data.
To fix this, handle errors in restoring the LED pin configuration separately.
If the restore succeeds, return any prior EEPROM timeout error correctly
to the caller.
Reported-by: syzbot+62ec8226f01cb4ca19d9@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=62ec8226f01cb4ca19d9
Fixes: 8b1b2ca83b ("net: usb: lan78xx: Improve error handling in EEPROM and OTP operations")
Signed-off-by: Bhanu Seshu Kumar Valluri <bhanuseshukumar@gmail.com>
Reviewed-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://patch.msgid.link/20250930084902.19062-1-bhanuseshukumar@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Cross-merge networking fixes after downstream PR (net-6.17-rc8).
Conflicts:
tools/testing/selftests/drivers/net/bonding/Makefile
87951b5664 selftests: bonding: add test for passive LACP mode
c2377f1763 selftests: bonding: add test for LACP actor port priority
Adjacent changes:
drivers/net/ethernet/cadence/macb.h
fca3dc859b net: macb: remove illusion about TBQPH/RBQPH being per-queue
89934dbf16 net: macb: Add TAPRIO traffic scheduling support
drivers/net/ethernet/cadence/macb_main.c
fca3dc859b net: macb: remove illusion about TBQPH/RBQPH being per-queue
89934dbf16 net: macb: Add TAPRIO traffic scheduling support
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
syzbot reported WARNING in rtl8150_start_xmit/usb_submit_urb.
This is the sequence of events that leads to the warning:
rtl8150_start_xmit() {
netif_stop_queue();
usb_submit_urb(dev->tx_urb);
}
rtl8150_set_multicast() {
netif_stop_queue();
netif_wake_queue(); <-- wakes up TX queue before URB is done
}
rtl8150_start_xmit() {
netif_stop_queue();
usb_submit_urb(dev->tx_urb); <-- double submission
}
rtl8150_set_multicast being the ndo_set_rx_mode callback should not be
calling netif_stop_queue and notif_start_queue as these handle
TX queue synchronization.
The net core function dev_set_rx_mode handles the synchronization
for rtl8150_set_multicast making it safe to remove these locks.
Reported-and-tested-by: syzbot+78cae3f37c62ad092caa@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=78cae3f37c62ad092caa
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Tested-by: Michal Pecio <michal.pecio@gmail.com>
Signed-off-by: I Viswanath <viswanathiyyappan@gmail.com>
Link: https://patch.msgid.link/20250924134350.264597-1-viswanathiyyappan@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Cross-merge networking fixes after downstream PR (net-6.17-rc4).
No conflicts.
Adjacent changes:
drivers/net/ethernet/intel/idpf/idpf_txrx.c
02614eee26 ("idpf: do not linearize big TSO packets")
6c4e684802 ("idpf: remove obsolete stashing code")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Without setting phy_mask for ax88772 mdio bus, current driver may create
at most 32 mdio phy devices with phy address range from 0x00 ~ 0x1f.
DLink DUB-E100 H/W Ver B1 is such a device. However, only one main phy
device will bind to net phy driver. This is creating issue during system
suspend/resume since phy_polling_mode() in phy_state_machine() will
directly deference member of phydev->drv for non-main phy devices. Then
NULL pointer dereference issue will occur. Due to only external phy or
internal phy is necessary, add phy_mask for ax88772 mdio bus to workarnoud
the issue.
Closes: https://lore.kernel.org/netdev/20250806082931.3289134-1-xu.yang_2@nxp.com
Fixes: e532a096be ("net: usb: asix: ax88772: add phylib support")
Cc: stable@vger.kernel.org
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Tested-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://patch.msgid.link/20250811092931.860333-1-xu.yang_2@nxp.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Merge in late fixes to prepare for the 6.17 net-next PR.
Conflicts:
net/core/neighbour.c
1bbb76a899 ("neighbour: Fix null-ptr-deref in neigh_flush_dev().")
13a936bb99 ("neighbour: Protect tbl->phash_buckets[] with a dedicated mutex.")
03dc03fa04 ("neighbor: Add NTF_EXT_VALIDATED flag for externally validated entries")
Adjacent changes:
drivers/net/usb/usbnet.c
0d9cfc9b8c ("net: usbnet: Avoid potential RCU stall on LINK_CHANGE event")
2c04d279e8 ("net: usb: Convert tasklet API to new bottom half workqueue mechanism")
net/ipv6/route.c
31d7d67ba1 ("ipv6: annotate data-races around rt->fib6_nsiblings")
1caf272972 ("ipv6: adopt dst_dev() helper")
3b3ccf9ed0 ("net: Remove unnecessary NULL check for lwtunnel_fill_encap()")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The Gemalto Cinterion PLS83-W modem (cdc_ether) is emitting confusing link
up and down events when the WWAN interface is activated on the modem-side.
Interrupt URBs will in consecutive polls grab:
* Link Connected
* Link Disconnected
* Link Connected
Where the last Connected is then a stable link state.
When the system is under load this may cause the unlink_urbs() work in
__handle_link_change() to not complete before the next usbnet_link_change()
call turns the carrier on again, allowing rx_submit() to queue new SKBs.
In that event the URB queue is filled faster than it can drain, ending up
in a RCU stall:
rcu: INFO: rcu_sched detected expedited stalls on CPUs/tasks: { 0-.... } 33108 jiffies s: 201 root: 0x1/.
rcu: blocking rcu_node structures (internal RCU debug):
Sending NMI from CPU 1 to CPUs 0:
NMI backtrace for cpu 0
Call trace:
arch_local_irq_enable+0x4/0x8
local_bh_enable+0x18/0x20
__netdev_alloc_skb+0x18c/0x1cc
rx_submit+0x68/0x1f8 [usbnet]
rx_alloc_submit+0x4c/0x74 [usbnet]
usbnet_bh+0x1d8/0x218 [usbnet]
usbnet_bh_tasklet+0x10/0x18 [usbnet]
tasklet_action_common+0xa8/0x110
tasklet_action+0x2c/0x34
handle_softirqs+0x2cc/0x3a0
__do_softirq+0x10/0x18
____do_softirq+0xc/0x14
call_on_irq_stack+0x24/0x34
do_softirq_own_stack+0x18/0x20
__irq_exit_rcu+0xa8/0xb8
irq_exit_rcu+0xc/0x30
el1_interrupt+0x34/0x48
el1h_64_irq_handler+0x14/0x1c
el1h_64_irq+0x68/0x6c
_raw_spin_unlock_irqrestore+0x38/0x48
xhci_urb_dequeue+0x1ac/0x45c [xhci_hcd]
unlink1+0xd4/0xdc [usbcore]
usb_hcd_unlink_urb+0x70/0xb0 [usbcore]
usb_unlink_urb+0x24/0x44 [usbcore]
unlink_urbs.constprop.0.isra.0+0x64/0xa8 [usbnet]
__handle_link_change+0x34/0x70 [usbnet]
usbnet_deferred_kevent+0x1c0/0x320 [usbnet]
process_scheduled_works+0x2d0/0x48c
worker_thread+0x150/0x1dc
kthread+0xd8/0xe8
ret_from_fork+0x10/0x20
Get around the problem by delaying the carrier on to the scheduled work.
This needs a new flag to keep track of the necessary action.
The carrier ok check cannot be removed as it remains required for the
LINK_RESET event flow.
Fixes: 4b49f58fff ("usbnet: handle link change")
Cc: stable@vger.kernel.org
Signed-off-by: John Ernberg <john.ernberg@actia.se>
Link: https://patch.msgid.link/20250723102526.1305339-1-john.ernberg@actia.se
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Implement ethtool .get_pauseparam and .set_pauseparam handlers for
configuring flow control on smsc95xx. The driver now supports enabling
or disabling transmit and receive pause frames, with or without
autonegotiation. Pause settings are applied during link-up based on
current PHY state and user configuration.
Previously, the driver used phy_get_pause() during link-up handling,
but lacked initialization and an ethtool interface to configure pause
modes. As a result, flow control support was effectively non-functional.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250718075157.297923-1-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This commit remove duplicate assignments for net->pcpu_stat_type
in usbnet_probe().
Signed-off-by: Zqiang <qiang.zhang@linux.dev>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Oleksij reported that:
The smsc95xx driver fails after one down/up cycle, like this:
$ nmcli device set enu1u1 managed no
$ p a a 10.10.10.1/24 dev enu1u1
$ ping -c 4 10.10.10.3
$ ip l s dev enu1u1 down
$ ip l s dev enu1u1 up
$ ping -c 4 10.10.10.3
The second ping does not reach the host. Networking also fails on other interfaces.
Enable the work by replacing the disable_work_sync() with cancel_work_sync().
[Jun Miao: completely write the commit changelog]
Fixes: 2c04d279e8 ("net: usb: Convert tasklet API to new bottom half workqueue mechanism")
Reported-by: Oleksij Rempel <o.rempel@pengutronix.de>
Tested-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Zqiang <qiang.zhang@linux.dev>
Signed-off-by: Jun Miao <jun.miao@intel.com>
Link: https://patch.msgid.link/20250708081653.307815-1-jun.miao@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If no PHY device is found (e.g., for LAN7801 in fixed-link mode),
lan78xx_phy_init() may proceed to dereference a NULL phydev pointer,
leading to a crash.
Update the logic to perform MAC configuration first, then check for the presence
of a PHY. For the fixed-link case, set up the fixed link and return early,
bypassing any code that assumes a valid phydev pointer.
It is safe to move lan78xx_mac_prepare_for_phy() earlier because this function
only uses information from dev->interface, which is configured by
lan78xx_get_phy() beforehand. The function does not access phydev or any data
set up by later steps.
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Fixes: e110bc8258 ("net: usb: lan78xx: Convert to PHYLINK for improved PHY and MAC management")
Link: https://patch.msgid.link/20250626103731.3986545-1-o.rempel@pengutronix.de
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Migrate tasklet APIs to the new bottom half workqueue mechanism. It
replaces all occurrences of tasklet usage with the appropriate workqueue
APIs throughout the usbnet driver. This transition ensures compatibility
with the latest design and enhances performance.
Signed-off-by: Jun Miao <jun.miao@intel.com>
Link: https://patch.msgid.link/20250618173923.950510-1-jun.miao@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Refactor Energy-Efficient Ethernet (EEE) support in the LAN78xx driver to
fully integrate with the phylink Low Power Idle (LPI) API. This includes:
- Replacing direct calls to `phy_ethtool_get_eee` and `phy_ethtool_set_eee`
with `phylink_ethtool_get_eee` and `phylink_ethtool_set_eee`.
- Implementing `.mac_enable_tx_lpi` and `.mac_disable_tx_lpi` to control
LPI transitions via phylink.
- Configuring `lpi_timer_default` to align with recommended values from
LAN7800 documentation.
- ensure EEE is disabled on controller reset
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/20250618122602.3156678-6-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Refactor lan78xx_get_link_ksettings and lan78xx_set_link_ksettings to
use the phylink API (phylink_ethtool_ksettings_get and
phylink_ethtool_ksettings_set) instead of directly interfacing with the
PHY. This change simplifies the code and ensures better integration with
the phylink framework for link management.
Additionally, the explicit calls to usb_autopm_get_interface() and
usb_autopm_put_interface() have been removed. These were originally
needed to manage USB power management during register accesses. However,
lan78xx_mdiobus_read() and lan78xx_mdiobus_write() already handle USB
auto power management internally, ensuring that the interface remains
active when necessary. Since there are no other direct register accesses
in these functions that require explicit power management handling, the
extra calls have become redundant and are no longer needed.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/20250618122602.3156678-5-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The EVENT_LINK_RESET macro currently triggers deferred work after a PHY
interrupt. Prior to PHYLINK conversion, this work included reconfiguring
the MAC and PHY, effectively performing a 'link reset'.
However, after porting the driver to the PHYLINK framework, the logic
associated with this event now solely handles the acknowledgment of
the PHY interrupt. The MAC and PHY reconfiguration is now managed by
PHYLINK's dedicated callbacks.
To accurately reflect its current, narrowed functionality, rename
EVENT_LINK_RESET to EVENT_PHY_INT_ACK.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/20250618122602.3156678-3-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Convert the LAN78xx USB Ethernet driver to use the PHYLINK framework for
managing PHY and MAC interactions. This improves consistency with other
network drivers, simplifies pause frame handling, and enables cleaner
suspend/resume support.
Key changes:
- Replace all PHYLIB-based logic with PHYLINK equivalents:
- Replace phy_connect()/phy_disconnect() with phylink_connect_phy()
- Replace phy_start()/phy_stop() with phylink_start()/phylink_stop()
- Replace pauseparam handling with phylink_ethtool_get/set_pauseparam()
- Introduce lan78xx_phylink_setup() to configure PHYLINK
- Add phylink MAC operations:
- lan78xx_mac_config()
- lan78xx_mac_link_up()
- lan78xx_mac_link_down()
- Remove legacy link state handling:
- lan78xx_link_status_change()
- lan78xx_link_reset()
- Handle fixed-link fallback for LAN7801 using phylink_set_fixed_link()
- Replace deprecated flow control handling with phylink-managed logic
Power management:
- Switch suspend/resume paths to use phylink_suspend()/phylink_resume()
- Ensure proper use of rtnl_lock() where required
- Note: full runtime testing of power management is currently limited
due to hardware setup constraints
Note: Conversion of EEE (Energy Efficient Ethernet) handling to the
PHYLINK-managed API will be done in a follow-up patch. For now, the
legacy EEE enable logic is preserved in mac_link_up().
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/20250618122602.3156678-2-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Pull networking fixes from Jakub Kicinski:
"Including fixes from bluetooth and wireless.
Current release - regressions:
- af_unix: allow passing cred for embryo without SO_PASSCRED/SO_PASSPIDFD
Current release - new code bugs:
- eth: airoha: correct enable mask for RX queues 16-31
- veth: prevent NULL pointer dereference in veth_xdp_rcv when peer
disappears under traffic
- ipv6: move fib6_config_validate() to ip6_route_add(), prevent
invalid routes
Previous releases - regressions:
- phy: phy_caps: don't skip better duplex match on non-exact match
- dsa: b53: fix untagged traffic sent via cpu tagged with VID 0
- Revert "wifi: mwifiex: Fix HT40 bandwidth issue.", it caused
transient packet loss, exact reason not fully understood, yet
Previous releases - always broken:
- net: clear the dst when BPF is changing skb protocol (IPv4 <> IPv6)
- sched: sfq: fix a potential crash on gso_skb handling
- Bluetooth: intel: improve rx buffer posting to avoid causing issues
in the firmware
- eth: intel: i40e: make reset handling robust against multiple
requests
- eth: mlx5: ensure FW pages are always allocated on the local NUMA
node, even when device is configure to 'serve' another node
- wifi: ath12k: fix GCC_GCC_PCIE_HOT_RST definition for WCN7850,
prevent kernel crashes
- wifi: ath11k: avoid burning CPU in ath11k_debugfs_fw_stats_request()
for 3 sec if fw_stats_done is not set"
* tag 'net-6.16-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (70 commits)
selftests: drv-net: rss_ctx: Add test for ntuple rules targeting default RSS context
net: ethtool: Don't check if RSS context exists in case of context 0
af_unix: Allow passing cred for embryo without SO_PASSCRED/SO_PASSPIDFD.
ipv6: Move fib6_config_validate() to ip6_route_add().
net: drv: netdevsim: don't napi_complete() from netpoll
net/mlx5: HWS, Add error checking to hws_bwc_rule_complex_hash_node_get()
veth: prevent NULL pointer dereference in veth_xdp_rcv
net_sched: remove qdisc_tree_flush_backlog()
net_sched: ets: fix a race in ets_qdisc_change()
net_sched: tbf: fix a race in tbf_change()
net_sched: red: fix a race in __red_change()
net_sched: prio: fix a race in prio_tune()
net_sched: sch_sfq: reject invalid perturb period
net: phy: phy_caps: Don't skip better duplex macth on non-exact match
MAINTAINERS: Update Kuniyuki Iwashima's email address.
selftests: net: add test case for NAT46 looping back dst
net: clear the dst when changing skb protocol
net/mlx5e: Fix number of lanes to UNKNOWN when using data_rate_oper
net/mlx5e: Fix leak of Geneve TLV option object
net/mlx5: HWS, make sure the uplink is the last destination
...
If we sanitize error returns, the debug statements need
to come before that so that we don't lose information.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Fixes: 405b0d6107 ("net: usb: aqc111: fix error handling of usbnet read calls")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
In mii_nway_restart() the code attempts to call
mii->mdio_read which is ch9200_mdio_read(). ch9200_mdio_read()
utilises a local buffer called "buff", which is initialised
with control_read(). However "buff" is conditionally
initialised inside control_read():
if (err == size) {
memcpy(data, buf, size);
}
If the condition of "err == size" is not met, then
"buff" remains uninitialised. Once this happens the
uninitialised "buff" is accessed and returned during
ch9200_mdio_read():
return (buff[0] | buff[1] << 8);
The problem stems from the fact that ch9200_mdio_read()
ignores the return value of control_read(), leading to
uinit-access of "buff".
To fix this we should check the return value of
control_read() and return early on error.
Reported-by: syzbot <syzbot+3361c2d6f78a3e0892f9@syzkaller.appspotmail.com>
Closes: https://syzkaller.appspot.com/bug?extid=3361c2d6f78a3e0892f9
Tested-by: syzbot <syzbot+3361c2d6f78a3e0892f9@syzkaller.appspotmail.com>
Fixes: 4a476bd6d1 ("usbnet: New driver for QinHeng CH9200 devices")
Cc: stable@vger.kernel.org
Signed-off-by: Qasim Ijaz <qasdev00@gmail.com>
Link: https://patch.msgid.link/20250526183607.66527-1-qasdev00@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Pull networking updates from Paolo Abeni:
"Core:
- Implement the Device Memory TCP transmit path, allowing zero-copy
data transmission on top of TCP from e.g. GPU memory to the wire.
- Move all the IPv6 routing tables management outside the RTNL scope,
under its own lock and RCU. The route control path is now 3x times
faster.
- Convert queue related netlink ops to instance lock, reducing again
the scope of the RTNL lock. This improves the control plane
scalability.
- Refactor the software crc32c implementation, removing unneeded
abstraction layers and improving significantly the related
micro-benchmarks.
- Optimize the GRO engine for UDP-tunneled traffic, for a 10%
performance improvement in related stream tests.
- Cover more per-CPU storage with local nested BH locking; this is a
prep work to remove the current per-CPU lock in local_bh_disable()
on PREMPT_RT.
- Introduce and use nlmsg_payload helper, combining buffer bounds
verification with accessing payload carried by netlink messages.
Netfilter:
- Rewrite the procfs conntrack table implementation, improving
considerably the dump performance. A lot of user-space tools still
use this interface.
- Implement support for wildcard netdevice in netdev basechain and
flowtables.
- Integrate conntrack information into nft trace infrastructure.
- Export set count and backend name to userspace, for better
introspection.
BPF:
- BPF qdisc support: BPF-qdisc can be implemented with BPF struct_ops
programs and can be controlled in similar way to traditional qdiscs
using the "tc qdisc" command.
- Refactor the UDP socket iterator, addressing long standing issues
WRT duplicate hits or missed sockets.
Protocols:
- Improve TCP receive buffer auto-tuning and increase the default
upper bound for the receive buffer; overall this improves the
single flow maximum thoughput on 200Gbs link by over 60%.
- Add AFS GSSAPI security class to AF_RXRPC; it provides transport
security for connections to the AFS fileserver and VL server.
- Improve TCP multipath routing, so that the sources address always
matches the nexthop device.
- Introduce SO_PASSRIGHTS for AF_UNIX, to allow disabling SCM_RIGHTS,
and thus preventing DoS caused by passing around problematic FDs.
- Retire DCCP socket. DCCP only receives updates for bugs, and major
distros disable it by default. Its removal allows for better
organisation of TCP fields to reduce the number of cache lines hit
in the fast path.
- Extend TCP drop-reason support to cover PAWS checks.
Driver API:
- Reorganize PTP ioctl flag support to require an explicit opt-in for
the drivers, avoiding the problem of drivers not rejecting new
unsupported flags.
- Converted several device drivers to timestamping APIs.
- Introduce per-PHY ethtool dump helpers, improving the support for
dump operations targeting PHYs.
Tests and tooling:
- Add support for classic netlink in user space C codegen, so that
ynl-c can now read, create and modify links, routes addresses and
qdisc layer configuration.
- Add ynl sub-types for binary attributes, allowing ynl-c to output
known struct instead of raw binary data, clarifying the classic
netlink output.
- Extend MPTCP selftests to improve the code-coverage.
- Add tests for XDP tail adjustment in AF_XDP.
New hardware / drivers:
- OpenVPN virtual driver: offload OpenVPN data channels processing to
the kernel-space, increasing the data transfer throughput WRT the
user-space implementation.
- Renesas glue driver for the gigabit ethernet RZ/V2H(P) SoC.
- Broadcom asp-v3.0 ethernet driver.
- AMD Renoir ethernet device.
- ReakTek MT9888 2.5G ethernet PHY driver.
- Aeonsemi 10G C45 PHYs driver.
Drivers:
- Ethernet high-speed NICs:
- nVidia/Mellanox (mlx5):
- refactor the steering table handling to significantly
reduce the amount of memory used
- add support for complex matches in H/W flow steering
- improve flow streeing error handling
- convert to netdev instance locking
- Intel (100G, ice, igb, ixgbe, idpf):
- ice: add switchdev support for LLDP traffic over VF
- ixgbe: add firmware manipulation and regions devlink support
- igb: introduce support for frame transmission premption
- igb: adds persistent NAPI configuration
- idpf: introduce RDMA support
- idpf: add initial PTP support
- Meta (fbnic):
- extend hardware stats coverage
- add devlink dev flash support
- Broadcom (bnxt):
- add support for RX-side device memory TCP
- Wangxun (txgbe):
- implement support for udp tunnel offload
- complete PTP and SRIOV support for AML 25G/10G devices
- Ethernet NICs embedded and virtual:
- Google (gve):
- add device memory TCP TX support
- Amazon (ena):
- support persistent per-NAPI config
- Airoha:
- add H/W support for L2 traffic offload
- add per flow stats for flow offloading
- RealTek (rtl8211): add support for WoL magic packet
- Synopsys (stmmac):
- dwmac-socfpga 1000BaseX support
- add Loongson-2K3000 support
- introduce support for hardware-accelerated VLAN stripping
- Broadcom (bcmgenet):
- expose more H/W stats
- Freescale (enetc, dpaa2-eth):
- enetc: add MAC filter, VLAN filter RSS and loopback support
- dpaa2-eth: convert to H/W timestamping APIs
- vxlan: convert FDB table to rhashtable, for better scalabilty
- veth: apply qdisc backpressure on full ring to reduce TX drops
- Ethernet switches:
- Microchip (kzZ88x3): add ETS scheduler support
- Ethernet PHYs:
- RealTek (rtl8211):
- add support for WoL magic packet
- add support for PHY LEDs
- CAN:
- Adds RZ/G3E CANFD support to the rcar_canfd driver.
- Preparatory work for CAN-XL support.
- Add self-tests framework with support for CAN physical interfaces.
- WiFi:
- mac80211:
- scan improvements with multi-link operation (MLO)
- Qualcomm (ath12k):
- enable AHB support for IPQ5332
- add monitor interface support to QCN9274
- add multi-link operation support to WCN7850
- add 802.11d scan offload support to WCN7850
- monitor mode for WCN7850, better 6 GHz regulatory
- Qualcomm (ath11k):
- restore hibernation support
- MediaTek (mt76):
- WiFi-7 improvements
- implement support for mt7990
- Intel (iwlwifi):
- enhanced multi-link single-radio (EMLSR) support on 5 GHz links
- rework device configuration
- RealTek (rtw88):
- improve throughput for RTL8814AU
- RealTek (rtw89):
- add multi-link operation support
- STA/P2P concurrency improvements
- support different SAR configs by antenna
- Bluetooth:
- introduce HCI Driver protocol
- btintel_pcie: do not generate coredump for diagnostic events
- btusb: add HCI Drv commands for configuring altsetting
- btusb: add RTL8851BE device 0x0bda:0xb850
- btusb: add new VID/PID 13d3/3584 for MT7922
- btusb: add new VID/PID 13d3/3630 and 13d3/3613 for MT7925
- btnxpuart: implement host-wakeup feature"
* tag 'net-next-6.16' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1611 commits)
selftests/bpf: Fix bpf selftest build warning
selftests: netfilter: Fix skip of wildcard interface test
net: phy: mscc: Stop clearing the the UDPv4 checksum for L2 frames
net: openvswitch: Fix the dead loop of MPLS parse
calipso: Don't call calipso functions for AF_INET sk.
selftests/tc-testing: Add a test for HFSC eltree double add with reentrant enqueue behaviour on netem
net_sched: hfsc: Address reentrant enqueue adding class to eltree twice
octeontx2-pf: QOS: Refactor TC_HTB_LEAF_DEL_LAST callback
octeontx2-pf: QOS: Perform cache sync on send queue teardown
net: mana: Add support for Multi Vports on Bare metal
net: devmem: ncdevmem: remove unused variable
net: devmem: ksft: upgrade rx test to send 1K data
net: devmem: ksft: add 5 tuple FS support
net: devmem: ksft: add exit_wait to make rx test pass
net: devmem: ksft: add ipv4 support
net: devmem: preserve sockc_err
page_pool: fix ugly page_pool formatting
net: devmem: move list_add to net_devmem_bind_dmabuf.
selftests: netfilter: nft_queue.sh: include file transfer duration in log message
net: phy: mscc: Fix memory leak when using one step timestamping
...
Pull irq cleanups from Thomas Gleixner:
"A set of cleanups for the generic interrupt subsystem:
- Consolidate on one set of functions for the interrupt domain code
to get rid of pointlessly duplicated code with only marginal
different semantics.
- Update the documentation accordingly and consolidate the coding
style of the irqdomain header"
* tag 'irq-cleanups-2025-05-25' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (46 commits)
irqdomain: Consolidate coding style
irqdomain: Fix kernel-doc and add it to Documentation
Documentation: irqdomain: Update it
Documentation: irq-domain.rst: Simple improvements
Documentation: irq/concepts: Minor improvements
Documentation: irq/concepts: Add commas and reflow
irqdomain: Improve kernel-docs of functions
irqdomain: Make struct irq_domain_info variables const
irqdomain: Use irq_domain_instantiate()'s return value as initializers
irqdomain: Drop irq_linear_revmap()
pinctrl: keembay: Switch to irq_find_mapping()
irqchip/armada-370-xp: Switch to irq_find_mapping()
gpu: ipu-v3: Switch to irq_find_mapping()
gpio: idt3243x: Switch to irq_find_mapping()
sh: Switch to irq_find_mapping()
powerpc: Switch to irq_find_mapping()
irqdomain: Drop irq_domain_add_*() functions
powerpc: Switch irq_domain_add_nomap() to use fwnode
thermal: Switch to irq_domain_create_linear()
soc: Switch to irq_domain_create_*()
...
Syzkaller, courtesy of syzbot, identified an error (see report [1]) in
aqc111 driver, caused by incomplete sanitation of usb read calls'
results. This problem is quite similar to the one fixed in commit
920a9fa27e ("net: asix: add proper error handling of usb read errors").
For instance, usbnet_read_cmd() may read fewer than 'size' bytes,
even if the caller expected the full amount, and aqc111_read_cmd()
will not check its result properly. As [1] shows, this may lead
to MAC address in aqc111_bind() being only partly initialized,
triggering KMSAN warnings.
Fix the issue by verifying that the number of bytes read is
as expected and not less.
[1] Partial syzbot report:
BUG: KMSAN: uninit-value in is_valid_ether_addr include/linux/etherdevice.h:208 [inline]
BUG: KMSAN: uninit-value in usbnet_probe+0x2e57/0x4390 drivers/net/usb/usbnet.c:1830
is_valid_ether_addr include/linux/etherdevice.h:208 [inline]
usbnet_probe+0x2e57/0x4390 drivers/net/usb/usbnet.c:1830
usb_probe_interface+0xd01/0x1310 drivers/usb/core/driver.c:396
call_driver_probe drivers/base/dd.c:-1 [inline]
really_probe+0x4d1/0xd90 drivers/base/dd.c:658
__driver_probe_device+0x268/0x380 drivers/base/dd.c:800
...
Uninit was stored to memory at:
dev_addr_mod+0xb0/0x550 net/core/dev_addr_lists.c:582
__dev_addr_set include/linux/netdevice.h:4874 [inline]
eth_hw_addr_set include/linux/etherdevice.h:325 [inline]
aqc111_bind+0x35f/0x1150 drivers/net/usb/aqc111.c:717
usbnet_probe+0xbe6/0x4390 drivers/net/usb/usbnet.c:1772
usb_probe_interface+0xd01/0x1310 drivers/usb/core/driver.c:396
...
Uninit was stored to memory at:
ether_addr_copy include/linux/etherdevice.h:305 [inline]
aqc111_read_perm_mac drivers/net/usb/aqc111.c:663 [inline]
aqc111_bind+0x794/0x1150 drivers/net/usb/aqc111.c:713
usbnet_probe+0xbe6/0x4390 drivers/net/usb/usbnet.c:1772
usb_probe_interface+0xd01/0x1310 drivers/usb/core/driver.c:396
call_driver_probe drivers/base/dd.c:-1 [inline]
...
Local variable buf.i created at:
aqc111_read_perm_mac drivers/net/usb/aqc111.c:656 [inline]
aqc111_bind+0x221/0x1150 drivers/net/usb/aqc111.c:713
usbnet_probe+0xbe6/0x4390 drivers/net/usb/usbnet.c:1772
Reported-by: syzbot+3b6b9ff7b80430020c7b@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=3b6b9ff7b80430020c7b
Tested-by: syzbot+3b6b9ff7b80430020c7b@syzkaller.appspotmail.com
Fixes: df2d59a2ab ("net: usb: aqc111: Add support for getting and setting of MAC address")
Signed-off-by: Nikita Zhandarovich <n.zhandarovich@fintech.ru>
Link: https://patch.msgid.link/20250520113240.2369438-1-n.zhandarovich@fintech.ru
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
