dev->chipid is used in lan78xx_init_mac_address before it's initialized:
lan78xx_reset() {
lan78xx_init_mac_address()
lan78xx_read_eeprom()
lan78xx_read_raw_eeprom() <- dev->chipid is used here
dev->chipid = ... <- dev->chipid is initialized correctly here
}
Reorder initialization so that dev->chipid is set before calling
lan78xx_init_mac_address().
Fixes: a0db7d10b7 ("lan78xx: Add to handle mux control per chip id")
Signed-off-by: I Viswanath <viswanathiyyappan@gmail.com>
Reviewed-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Reviewed-by: Khalid Aziz <khalid@kernel.org>
Link: https://patch.msgid.link/20251013181648.35153-1-viswanathiyyappan@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Marc Kleine-Budde says:
====================
pull-request: can 2025-10-14
The first 2 paches are by Celeste Liu and target the gS_usb driver.
The first patch remove the limitation to 3 CAN interface per USB
device. The second patch adds the missing population of
net_device->dev_port.
The next 4 patches are by me and fix the m_can driver. They add a
missing pm_runtime_disable(), fix the CAN state transition back to
Error Active and fix the state after ifup and suspend/resume.
Another patch by me targets the m_can driver, too and replaces Dong
Aisheng's old email address.
The next 2 patches are by Vincent Mailhol and update the CAN
networking Documentation.
Tetsuo Handa contributes the last patch that add missing cleanup calls
in the NETDEV_UNREGISTER notification handler.
* tag 'linux-can-fixes-for-6.18-20251014' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can:
can: j1939: add missing calls in NETDEV_UNREGISTER notification handler
can: add Transmitter Delay Compensation (TDC) documentation
can: remove false statement about 1:1 mapping between DLC and length
can: m_can: replace Dong Aisheng's old email address
can: m_can: fix CAN state in system PM
can: m_can: m_can_chip_config(): bring up interface in correct state
can: m_can: m_can_handle_state_errors(): fix CAN state transition to Error Active
can: m_can: m_can_plat_remove(): add missing pm_runtime_disable()
can: gs_usb: gs_make_candev(): populate net_device->dev_port
can: gs_usb: increase max interface to U8_MAX
====================
Link: https://patch.msgid.link/20251014122140.990472-1-mkl@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Bringing a linked netdevsim device down and then up causes communication
failure because both interfaces lack carrier. Basically a ifdown/ifup on
the interface make the link broken.
Commit 3762ec05a9 ("netdevsim: add NAPI support") added supported
for NAPI, calling netif_carrier_off() in nsim_stop(). This patch
re-enables the carrier symmetrically on nsim_open(), in case the device
is linked and the peer is up.
Signed-off-by: Breno Leitao <leitao@debian.org>
Fixes: 3762ec05a9 ("netdevsim: add NAPI support")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20251014-netdevsim_fix-v2-1-53b40590dae1@debian.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Completion napi can free out-of-order tx descriptors if hw QoS is
enabled and packets with different priority are queued to same DMA ring.
Take into account possible out-of-order reports checking if the tx queue
is full using circular buffer head/tail pointer instead of the number of
queued packets.
Fixes: 23020f0493 ("net: airoha: Introduce ethernet support for EN7581 SoC")
Suggested-by: Simon Horman <horms@kernel.org>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20251012-airoha-tx-busy-queue-v2-1-a600b08bab2d@kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
During interface toggle operations (ifdown/ifup), the driver currently
resets the local helper variable 'phy_link' to -1. This causes the link
state machine to incorrectly interpret the state as a link change event,
resulting in spurious "Link is down" messages being logged when the
interface is brought back up.
Preserve the phy_link state across interface toggles to avoid treating
the -1 sentinel value as a legitimate link state transition.
Fixes: 88131a812b ("amd-xgbe: Perform phy connect/disconnect at dev open/stop")
Signed-off-by: Raju Rangoju <Raju.Rangoju@amd.com>
Reviewed-by: Dawid Osuchowski <dawid.osuchowski@linux.intel.com>
Link: https://patch.msgid.link/20251010065142.1189310-1-Raju.Rangoju@amd.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
There was backward compatibility in the terms of mailbox API. Various
drivers from various OSes supporting 10G adapters from Intel portfolio
could easily negotiate mailbox API.
This convention has been broken since introducing API 1.4.
Commit 0062e7cc95 ("ixgbevf: add VF IPsec offload code") added support
for IPSec which is specific only for the kernel ixgbe driver. None of the
rest of the Intel 10G PF/VF drivers supports it. And actually lack of
support was not included in the IPSec implementation - there were no such
code paths. No possibility to negotiate support for the feature was
introduced along with introduction of the feature itself.
Commit 339f289641 ("ixgbevf: Add support for new mailbox communication
between PF and VF") increasing API version to 1.5 did the same - it
introduced code supported specifically by the PF ESX driver. It altered API
version for the VF driver in the same time not touching the version
defined for the PF ixgbe driver. It led to additional discrepancies,
as the code provided within API 1.6 cannot be supported for Linux ixgbe
driver as it causes crashes.
The issue was noticed some time ago and mitigated by Jake within the commit
d0725312ad ("ixgbevf: stop attempting IPSEC offload on Mailbox API 1.5").
As a result we have regression for IPsec support and after increasing API
to version 1.6 ixgbevf driver stopped to support ESX MBX.
To fix this mess add new mailbox op asking PF driver about supported
features. Basing on a response determine whether to set support for IPSec
and ESX-specific enhanced mailbox.
New mailbox op, for compatibility purposes, must be added within new API
revision, as API version of OOT PF & VF drivers is already increased to
1.6 and doesn't incorporate features negotiate op.
Features negotiation mechanism gives possibility to be extended with new
features when needed in the future.
Reported-by: Jacob Keller <jacob.e.keller@intel.com>
Closes: https://lore.kernel.org/intel-wired-lan/20241101-jk-ixgbevf-mailbox-v1-5-fixes-v1-0-f556dc9a66ed@intel.com/
Fixes: 0062e7cc95 ("ixgbevf: add VF IPsec offload code")
Fixes: 339f289641 ("ixgbevf: Add support for new mailbox communication between PF and VF")
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Jedrzej Jagielski <jedrzej.jagielski@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/20251009-jk-iwl-net-2025-10-01-v3-4-ef32a425b92a@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When the driver requests Tx timestamp value, one of the first steps is
to clone SKB using skb_get. It increases the reference counter for that
SKB to prevent unexpected freeing by another component.
However, there may be a case where the index is requested, SKB is
assigned and never consumed by PTP flows - for example due to reset during
running PTP apps.
Add a check in release timestamping function to verify if the SKB
assigned to Tx timestamp latch was freed, and release remaining SKBs.
Fixes: 4901e83a94 ("idpf: add Tx timestamp capabilities negotiation")
Signed-off-by: Milena Olech <milena.olech@intel.com>
Signed-off-by: Anton Nadezhdin <anton.nadezhdin@intel.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Tested-by: Samuel Salin <Samuel.salin@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/20251009-jk-iwl-net-2025-10-01-v3-1-ef32a425b92a@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
After resume from S4 (hibernate), RTL8168H/RTL8111H truncates incoming
packets. Packet captures show messages like "IP truncated-ip - 146 bytes
missing!".
The issue is caused by RxConfig not being properly re-initialized after
resume. Re-initializing the RxConfig register before the chip
re-initialization sequence avoids the truncation and restores correct
packet reception.
This follows the same pattern as commit ef9da46dde ("r8169: fix data
corruption issue on RTL8402").
Fixes: 6e1d0b8988 ("r8169:add support for RTL8168H and RTL8107E")
Signed-off-by: Linmao Li <lilinmao@kylinos.cn>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://patch.msgid.link/20251009122549.3955845-1-lilinmao@kylinos.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There is no error handling for `dma_map_single()` failures.
Add error handling by checking `dma_mapping_error()` and freeing
the `skb` using `dev_kfree_skb()` (process context) when it fails.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Yeounsu Moon <yyyynoom@gmail.com>
Tested-on: D-Link DGE-550T Rev-A3
Suggested-by: Simon Horman <horms@kernel.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Limit tx/rx buffer address to 32-bit address space for board with more
than 4GB DRAM.
Fixes: 804775dfc2 ("net: ethernet: mtk_eth_soc: add support for Wireless Ethernet Dispatch (WED)")
Fixes: 6757d345dd ("net: ethernet: mtk_wed: introduce hw_rro support for MT7988")
Tested-by: Daniel Pawlik <pawlik.dan@gmail.com>
Tested-by: Matteo Croce <teknoraver@meta.com>
Signed-off-by: Rex Lu <rex.lu@mediatek.com>
Co-developed-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function lan78xx_write_raw_eeprom failed to properly propagate EEPROM
write timeout errors (-ETIMEDOUT). In the timeout fallthrough path, it first
attempted to restore the pin configuration for LED outputs and then
returned only the status of that restore operation, discarding the
original timeout error saved in ret.
As a result, callers could mistakenly treat EEPROM write operation as
successful even though the EEPROM write had actually timed out with no
or partial data write.
To fix this, handle errors in restoring the LED pin configuration separately.
If the restore succeeds, return any prior EEPROM write timeout error saved
in ret to the caller.
Suggested-by: Oleksij Rempel <o.rempel@pengutronix.de>
Fixes: 8b1b2ca83b ("net: usb: lan78xx: Improve error handling in EEPROM and OTP operations")
cc: stable@vger.kernel.org
Signed-off-by: Bhanu Seshu Kumar Valluri <bhanuseshukumar@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from Paolo Abeni:
"Including fixes from netfilter.
Current release - regressions:
- mlx5: fix pre-2.40 binutils assembler error
Current release - new code bugs:
- net: psp: don't assume reply skbs will have a socket
- eth: fbnic: fix missing programming of the default descriptor
Previous releases - regressions:
- page_pool: fix PP_MAGIC_MASK to avoid crashing on some 32-bit arches
- tcp:
- take care of zero tp->window_clamp in tcp_set_rcvlowat()
- don't call reqsk_fastopen_remove() in tcp_conn_request()
- eth:
- ice: release xa entry on adapter allocation failure
- usb: asix: hold PM usage ref to avoid PM/MDIO + RTNL deadlock
Previous releases - always broken:
- netfilter: validate objref and objrefmap expressions
- sctp: fix a null dereference in sctp_disposition sctp_sf_do_5_1D_ce()
- eth:
- mlx4: prevent potential use after free in mlx4_en_do_uc_filter()
- mlx5: prevent tunnel mode conflicts between FDB and NIC IPsec tables
- ocelot: fix use-after-free caused by cyclic delayed work
Misc:
- add support for MediaTek PCIe 5G HP DRMR-H01"
* tag 'net-6.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (38 commits)
net: airoha: Fix loopback mode configuration for GDM2 port
selftests: drv-net: pp_alloc_fail: add necessary optoins to config
selftests: drv-net: pp_alloc_fail: lower traffic expectations
selftests: drv-net: fix linter warnings in pp_alloc_fail
eth: fbnic: fix reporting of alloc_failed qstats
selftests: drv-net: xdp: add test for interface level qstats
selftests: drv-net: xdp: rename netnl to ethnl
eth: fbnic: fix saving stats from XDP_TX rings on close
eth: fbnic: fix accounting of XDP packets
eth: fbnic: fix missing programming of the default descriptor
selftests: netfilter: query conntrack state to check for port clash resolution
selftests: netfilter: nft_fib.sh: fix spurious test failures
bridge: br_vlan_fill_forward_path_pvid: use br_vlan_group_rcu()
netfilter: nft_objref: validate objref and objrefmap expressions
net: pse-pd: tps23881: Fix current measurement scaling
net/mlx5: fix pre-2.40 binutils assembler error
net/mlx5e: Do not fail PSP init on missing caps
net/mlx5e: Prevent tunnel reformat when tunnel mode not allowed
net/mlx5: Prevent tunnel mode conflicts between FDB and NIC IPsec tables
net: usb: asix: hold PM usage ref to avoid PM/MDIO + RTNL deadlock
...
Rx processing under normal circumstances has 3 rings - 2 buffer
rings (heads, payloads) and a completion ring. All the rings
have a struct fbnic_ring. Make sure we expose alloc_failed
counter from the buffer rings, previously only the alloc_failed
from the completion ring was reported, even tho all ring types
may increment this counter (buffer rings in __fbnic_fill_bdq()).
This makes the pp_alloc_fail.py test pass, it expects the qstat
to be incrementing as page pool injections happen.
Reviewed-by: Simon Horman <horms@kernel.org>
Fixes: 67dc4eb5fc ("eth: fbnic: report software Rx queue stats")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/20251007232653.2099376-7-kuba@kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
When rings are freed - stats get added to the device level stat
structs. Save the stats from the XDP_TX ring just as Tx stats.
Previously they would be saved to Rx and Tx stats. So we'd not
see XDP_TX packets as Rx during runtime but after an down/up cycle
the packets would appear in stats.
Correct the helper used by ethtool code which does a runtime
config switch.
Reviewed-by: Simon Horman <horms@kernel.org>
Fixes: 5213ff0863 ("eth: fbnic: Collect packet statistics for XDP")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/20251007232653.2099376-4-kuba@kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Make XDP-handled packets appear in the Rx stats. The driver has been
counting XDP_TX packets on the Tx ring, but there wasn't much accounting
on the Rx side (the Rx bytes appear to be incremented on XDP_TX but
XDP_DROP / XDP_ABORT are only counted as Rx drops).
Counting XDP_TX packets (not just bytes) in Rx stats looks like
a simple bug of omission.
The XDP_DROP handling appears to be intentional. Whether XDP_DROP
packets should be counted in interface-level Rx stats is a bit
unclear historically. When we were defining qstats, however,
we clarified based on operational experience that in this context:
name: rx-packets
doc: |
Number of wire packets successfully received and passed to the stack.
For drivers supporting XDP, XDP is considered the first layer
of the stack, so packets consumed by XDP are still counted here.
fbnic does not obey this requirement. Since XDP support has been added
in current release cycle, instead of splitting interface and qstat
handling - make them both follow the qstat definition.
Another small tweak here is that we count bytes as received on the wire
rather than post-XDP bytes (xdp_get_buff_len() vs skb->len).
Reviewed-by: Simon Horman <horms@kernel.org>
Fixes: 5213ff0863 ("eth: fbnic: Collect packet statistics for XDP")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/20251007232653.2099376-3-kuba@kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
XDP_TX typically uses no offloads. To optimize XDP we added a "default
descriptor" feature to the chip, which allows us to send XDP frames with
just the buffer descriptors (DMA address + length). All the metadata
descriptors are derived from the queue config.
Commit under Fixes missed adding setting the defaults up when transplanting
the code from the prototype driver. Importantly after reset the "request
completion" bit is not set. Packets still get sent but there's no
completion, so ring is not cleaned up. We can send one ring's worth
of packets and then will start dropping all frames that got the XDP_TX
action from the XDP prog.
Reviewed-by: Simon Horman <horms@kernel.org>
Fixes: 168deb7b31 ("eth: fbnic: Add support for XDP_TX action")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/20251007232653.2099376-2-kuba@kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
A suspend/resume cycle on a down interface results in the interface
coming up in Error Active state. A suspend/resume cycle on an Up
interface will always result in Error Active state, regardless of the
actual CAN state.
During suspend, only set running interfaces to CAN_STATE_SLEEPING.
During resume only touch the CAN state of running interfaces. For
wakeup sources, set the CAN state depending on the Protocol Status
Regitser (PSR), for non wakeup source interfaces m_can_start() will do
the same.
Fixes: e0d1f4816f ("can: m_can: add Bosch M_CAN controller support")
Reviewed-by: Markus Schneider-Pargmann <msp@baylibre.com>
Link: https://patch.msgid.link/20250929-m_can-fix-state-handling-v4-4-682b49b49d9a@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
In some SoCs (observed on the STM32MP15) the M_CAN IP core keeps the
CAN state and CAN error counters over an internal reset cycle. An
external reset is not always possible, due to the shared reset with
the other CAN core. This caused the core not always be in Error Active
state when bringing up the controller.
Instead of always setting the CAN state to Error Active in
m_can_chip_config(), fix this by reading and decoding the Protocol
Status Regitser (PSR) and set the CAN state accordingly.
Fixes: e0d1f4816f ("can: m_can: add Bosch M_CAN controller support")
Reviewed-by: Markus Schneider-Pargmann <msp@baylibre.com>
Link: https://patch.msgid.link/20250929-m_can-fix-state-handling-v4-3-682b49b49d9a@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The CAN Error State is determined by the receive and transmit error
counters. The CAN error counters decrease when reception/transmission
is successful, so that a status transition back to the Error Active
status is possible. This transition is not handled by
m_can_handle_state_errors().
Add the missing detection of the Error Active state to
m_can_handle_state_errors() and extend the handling of this state in
m_can_handle_state_change().
Fixes: e0d1f4816f ("can: m_can: add Bosch M_CAN controller support")
Fixes: cd0d83eab2 ("can: m_can: m_can_handle_state_change(): fix state change")
Reviewed-by: Markus Schneider-Pargmann <msp@baylibre.com>
Link: https://patch.msgid.link/20250929-m_can-fix-state-handling-v4-2-682b49b49d9a@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Commit 227619c3ff ("can: m_can: move runtime PM enable/disable to
m_can_platform") moved the PM runtime enable from the m_can core
driver into the m_can_platform.
That patch forgot to move the pm_runtime_disable() to
m_can_plat_remove(), so that unloading the m_can_platform driver
causes an "Unbalanced pm_runtime_enable!" error message.
Add the missing pm_runtime_disable() to m_can_plat_remove() to fix the
problem.
Cc: Patrik Flykt <patrik.flykt@linux.intel.com>
Fixes: 227619c3ff ("can: m_can: move runtime PM enable/disable to m_can_platform")
Reviewed-by: Markus Schneider-Pargmann <msp@baylibre.com>
Link: https://patch.msgid.link/20250929-m_can-fix-state-handling-v4-1-682b49b49d9a@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The gs_usb driver supports USB devices with more than 1 CAN channel.
In old kernel before 3.15, it uses net_device->dev_id to distinguish
different channel in userspace, which was done in commit
acff76fa45 ("can: gs_usb: gs_make_candev(): set netdev->dev_id").
But since 3.15, the correct way is populating net_device->dev_port.
And according to documentation, if network device support multiple
interface, lack of net_device->dev_port SHALL be treated as a bug.
Fixes: acff76fa45 ("can: gs_usb: gs_make_candev(): set netdev->dev_id")
Cc: stable@vger.kernel.org
Signed-off-by: Celeste Liu <uwu@coelacanthus.name>
Link: https://patch.msgid.link/20250930-gs-usb-populate-net_device-dev_port-v1-1-68a065de6937@coelacanthus.name
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This issue was found by Runcheng Lu when develop HSCanT USB to CAN FD
converter[1]. The original developers may have only 3 interfaces
device to test so they write 3 here and wait for future change.
During the HSCanT development, we actually used 4 interfaces, so the
limitation of 3 is not enough now. But just increase one is not
future-proofed. Since the channel index type in gs_host_frame is u8,
just make canch[] become a flexible array with a u8 index, so it
naturally constraint by U8_MAX and avoid statically allocate 256
pointer for every gs_usb device.
[1]: https://github.com/cherry-embedded/HSCanT-hardware
Fixes: d08e973a77 ("can: gs_usb: Added support for the GS_USB CAN devices")
Reported-by: Runcheng Lu <runcheng.lu@hpmicro.com>
Cc: stable@vger.kernel.org
Reviewed-by: Vincent Mailhol <mailhol@kernel.org>
Signed-off-by: Celeste Liu <uwu@coelacanthus.name>
Link: https://patch.msgid.link/20250930-gs-usb-max-if-v5-1-863330bf6666@coelacanthus.name
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The TPS23881 improves on the TPS23880 with current sense resistors reduced
from 255 mOhm to 200 mOhm. This has a direct impact on the scaling of the
current measurement. However, the latest TPS23881 data sheet from May 2023
still shows the scaling of the TPS23880 model.
Fixes: 7f076ce3f1 ("net: pse-pd: tps23881: Add support for power limit and measurement features")
Signed-off-by: Thomas Wismer <thomas.wismer@scs.ch>
Acked-by: Kory Maincent <kory.maincent@bootlin.com>
Link: https://patch.msgid.link/20251006204029.7169-2-thomas@wismer.xyz
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Pull hyperv updates from Wei Liu:
- Unify guest entry code for KVM and MSHV (Sean Christopherson)
- Switch Hyper-V MSI domain to use msi_create_parent_irq_domain()
(Nam Cao)
- Add CONFIG_HYPERV_VMBUS and limit the semantics of CONFIG_HYPERV
(Mukesh Rathor)
- Add kexec/kdump support on Azure CVMs (Vitaly Kuznetsov)
- Deprecate hyperv_fb in favor of Hyper-V DRM driver (Prasanna
Kumar T S M)
- Miscellaneous enhancements, fixes and cleanups (Abhishek Tiwari,
Alok Tiwari, Nuno Das Neves, Wei Liu, Roman Kisel, Michael Kelley)
* tag 'hyperv-next-signed-20251006' of git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux:
hyperv: Remove the spurious null directive line
MAINTAINERS: Mark hyperv_fb driver Obsolete
fbdev/hyperv_fb: deprecate this in favor of Hyper-V DRM driver
Drivers: hv: Make CONFIG_HYPERV bool
Drivers: hv: Add CONFIG_HYPERV_VMBUS option
Drivers: hv: vmbus: Fix typos in vmbus_drv.c
Drivers: hv: vmbus: Fix sysfs output format for ring buffer index
Drivers: hv: vmbus: Clean up sscanf format specifier in target_cpu_store()
x86/hyperv: Switch to msi_create_parent_irq_domain()
mshv: Use common "entry virt" APIs to do work in root before running guest
entry: Rename "kvm" entry code assets to "virt" to genericize APIs
entry/kvm: KVM: Move KVM details related to signal/-EINTR into KVM proper
mshv: Handle NEED_RESCHED_LAZY before transferring to guest
x86/hyperv: Add kexec/kdump support on Azure CVMs
Drivers: hv: Simplify data structures for VMBus channel close message
Drivers: hv: util: Cosmetic changes for hv_utils_transport.c
mshv: Add support for a new parent partition configuration
clocksource: hyper-v: Skip unnecessary checks for the root partition
hyperv: Add missing field to hv_output_map_device_interrupt
PSP support requires a set of cap bits to be set, otherwise an init
error is logged.
But logging an error when PSP cannot be initialized is too much, and not
in line with other features. If a feature cannot be initialized because
it is not supported, that's not an error. An error should only be
printed when the feature cannot be initialized because of an actual
error.
Fixes: 89ee2d92f6 ("net/mlx5e: Support PSP offload functionality")
Signed-off-by: Cosmin Ratiu <cratiu@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/1759652999-858513-4-git-send-email-tariqt@nvidia.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
When configuring IPsec packet offload in tunnel mode, the driver tries
to create tunnel reformat objects unconditionally. This is incorrect,
because tunnel mode is only permitted under specific encapsulation
settings, and that decision is already made when the flow table is
created.
The offending commit attempted to block this case in the state add
path, but the check there happens too late and does not prevent the
reformat from being configured.
Fix by taking short reservations for both the eswitch mode and the
encap at the start of state setup. This preserves the block ordering
(mode --> encap) used later: the mode is blocked during RX/TX get, and
the encap is blocked during flow-table creation. This lets us fail
early if either reservation cannot be obtained, it means a mode
transition is underway or a conflicting configuration already owns
encap. If both succeed, the flow-table path later takes the ownership
and the reservations are released on exit.
Fixes: 146c196b60 ("net/mlx5e: Create IPsec table with tunnel support only when encap is disabled")
Signed-off-by: Carolina Jubran <cjubran@nvidia.com>
Reviewed-by: Jianbo Liu <jianbol@nvidia.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/1759652999-858513-3-git-send-email-tariqt@nvidia.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
When creating IPsec flow tables with tunnel mode enabled, the driver
uses mlx5_eswitch_block_encap() to prevent tunnel encapsulation
conflicts across different domains (NIC_RX/NIC_TX and FDB), since the
firmware doesn’t allow both at the same time.
Currently, the driver attempts to reserve tunnel mode unconditionally
for both NIC and FDB IPsec tables. This can lead to conflicting tunnel
mode setups, for example, if a flow table was created in the FDB
domain with tunnel offload enabled, and we later try to create another
one in the NIC, or vice versa.
To resolve this, adjust the blocking logic so that tunnel mode is only
reserved by NIC flows. This ensures that tunnel offload is exclusively
used in either the NIC or the FDB, and avoids unintended offload
conflicts.
Fixes: 1762f132d5 ("net/mlx5e: Support IPsec packet offload for RX in switchdev mode")
Fixes: c6c2bf5db4 ("net/mlx5e: Support IPsec packet offload for TX in switchdev mode")
Signed-off-by: Carolina Jubran <cjubran@nvidia.com>
Reviewed-by: Jianbo Liu <jianbol@nvidia.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/1759652999-858513-2-git-send-email-tariqt@nvidia.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Prevent USB runtime PM (autosuspend) for AX88772* in bind.
usbnet enables runtime PM (autosuspend) by default, so disabling it via
the usb_driver flag is ineffective. On AX88772B, autosuspend shows no
measurable power saving with current driver (no link partner, admin
up/down). The ~0.453 W -> ~0.248 W drop on v6.1 comes from phylib powering
the PHY off on admin-down, not from USB autosuspend.
The real hazard is that with runtime PM enabled, ndo_open() (under RTNL)
may synchronously trigger autoresume (usb_autopm_get_interface()) into
asix_resume() while the USB PM lock is held. Resume paths then invoke
phylink/phylib and MDIO, which also expect RTNL, leading to possible
deadlocks or PM lock vs MDIO wake issues.
To avoid this, keep the device runtime-PM active by taking a usage
reference in ax88772_bind() and dropping it in unbind(). A non-zero PM
usage count blocks runtime suspend regardless of userspace policy
(.../power/control - pm_runtime_allow/forbid), making this approach
robust against sysfs overrides.
Holding a runtime-PM usage ref does not affect system-wide suspend;
system sleep/resume callbacks continue to run as before.
Fixes: 4a2c7217cd ("net: usb: asix: ax88772: manage PHY PM from MAC")
Reported-by: Hubert Wiśniewski <hubert.wisniewski.25632@gmail.com>
Closes: https://lore.kernel.org/all/DCGHG5UJT9G3.2K1GHFZ3H87T0@gmail.com
Tested-by: Hubert Wiśniewski <hubert.wisniewski.25632@gmail.com>
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Closes: https://lore.kernel.org/all/b5ea8296-f981-445d-a09a-2f389d7f6fdd@samsung.com
Cc: stable@vger.kernel.org
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://patch.msgid.link/20251005081203.3067982-1-o.rempel@pengutronix.de
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The sparx5 driver programs UC/MC/BC flooding in sparx5_update_fwd() by
unconditionally applying bridge_fwd_mask to all flood PGIDs. Any bridge
topology change that triggers sparx5_update_fwd() (for example enslaving
another port) therefore reinstalls flooding in hardware for already
bridged ports, regardless of their per-port flood flags.
This results in clobbering of the flood masks, and desynchronization
between software and hardware: the bridge still reports “flood off” for
the port, but hardware has flooding enabled due to unconditional PGID
reprogramming.
Steps to reproduce:
$ ip link add br0 type bridge
$ ip link set br0 up
$ ip link set eth0 master br0
$ ip link set eth0 up
$ bridge link set dev eth0 flood off
$ ip link set eth1 master br0
$ ip link set eth1 up
At this point, flooding is silently re-enabled for eth0. Software still
shows “flood off” for eth0, but hardware has flooding enabled.
To fix this, flooding is now set explicitly during bridge join/leave,
through sparx5_port_attr_bridge_flags():
On bridge join, UC/MC/BC flooding is enabled by default.
On bridge leave, UC/MC/BC flooding is disabled.
sparx5_update_fwd() no longer touches the flood PGIDs, clobbering
the flood masks, and desynchronizing software and hardware.
Initialization of the flooding PGIDs have been moved to
sparx5_start(). This is required as flooding PGIDs defaults to
0x3fffffff in hardware and the initialization was previously handled
in sparx5_update_fwd(), which was removed.
With this change, user-configured flooding flags persist across bridge
updates and are no longer overridden by sparx5_update_fwd().
Fixes: d6fce51419 ("net: sparx5: add switching support")
Signed-off-by: Daniel Machon <daniel.machon@microchip.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20251003-fix-flood-fwd-v1-1-48eb478b2904@microchip.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
When accessing an MDIO register using single-byte smbus accesses, we have to
perform 2 consecutive operations targeting the same address,
first accessing the MSB then the LSB of the 16 bit register:
read_1_byte(addr); <- returns MSB of register at address 'addr'
read_1_byte(addr); <- returns LSB
Some PHY devices present in SFP such as the Broadcom 5461 don't like
seeing foreign i2c transactions in-between these 2 smbus accesses, and
will return the MSB a second time when trying to read the LSB :
read_1_byte(addr); <- returns MSB
i2c_transaction_for_other_device_on_the_bus();
read_1_byte(addr); <- returns MSB again
Given the already fragile nature of accessing PHYs/SFPs with single-byte
smbus accesses, it's safe to say that this Broadcom PHY may not be the
only one acting like this.
Let's therefore hold the i2c bus lock while performing our smbus
transactions to avoid interleaved accesses.
Fixes: d4bd3aca33 ("net: mdio: mdio-i2c: Add support for single-byte SMBus operations")
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Kory Maincent <kory.maincent@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20251003070311.861135-1-maxime.chevallier@bootlin.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
When ice_adapter_new() fails, the reserved XArray entry created by
xa_insert() is not released. This causes subsequent insertions at
the same index to return -EBUSY, potentially leading to
NULL pointer dereferences.
Reorder the operations as suggested by Przemek Kitszel:
1. Check if adapter already exists (xa_load)
2. Reserve the XArray slot (xa_reserve)
3. Allocate the adapter (ice_adapter_new)
4. Store the adapter (xa_store)
Fixes: 0f0023c649 ("ice: do not init struct ice_adapter more times than needed")
Suggested-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Suggested-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Haotian Zhang <vulab@iscas.ac.cn>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/20251001115336.1707-1-vulab@iscas.ac.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The origin code calls cancel_delayed_work() in ocelot_stats_deinit()
to cancel the cyclic delayed work item ocelot->stats_work. However,
cancel_delayed_work() may fail to cancel the work item if it is already
executing. While destroy_workqueue() does wait for all pending work items
in the work queue to complete before destroying the work queue, it cannot
prevent the delayed work item from being rescheduled within the
ocelot_check_stats_work() function. This limitation exists because the
delayed work item is only enqueued into the work queue after its timer
expires. Before the timer expiration, destroy_workqueue() has no visibility
of this pending work item. Once the work queue appears empty,
destroy_workqueue() proceeds with destruction. When the timer eventually
expires, the delayed work item gets queued again, leading to the following
warning:
workqueue: cannot queue ocelot_check_stats_work on wq ocelot-switch-stats
WARNING: CPU: 2 PID: 0 at kernel/workqueue.c:2255 __queue_work+0x875/0xaf0
...
RIP: 0010:__queue_work+0x875/0xaf0
...
RSP: 0018:ffff88806d108b10 EFLAGS: 00010086
RAX: 0000000000000000 RBX: 0000000000000101 RCX: 0000000000000027
RDX: 0000000000000027 RSI: 0000000000000004 RDI: ffff88806d123e88
RBP: ffffffff813c3170 R08: 0000000000000000 R09: ffffed100da247d2
R10: ffffed100da247d1 R11: ffff88806d123e8b R12: ffff88800c00f000
R13: ffff88800d7285c0 R14: ffff88806d0a5580 R15: ffff88800d7285a0
FS: 0000000000000000(0000) GS:ffff8880e5725000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007fe18e45ea10 CR3: 0000000005e6c000 CR4: 00000000000006f0
Call Trace:
<IRQ>
? kasan_report+0xc6/0xf0
? __pfx_delayed_work_timer_fn+0x10/0x10
? __pfx_delayed_work_timer_fn+0x10/0x10
call_timer_fn+0x25/0x1c0
__run_timer_base.part.0+0x3be/0x8c0
? __pfx_delayed_work_timer_fn+0x10/0x10
? rcu_sched_clock_irq+0xb06/0x27d0
? __pfx___run_timer_base.part.0+0x10/0x10
? try_to_wake_up+0xb15/0x1960
? _raw_spin_lock_irq+0x80/0xe0
? __pfx__raw_spin_lock_irq+0x10/0x10
tmigr_handle_remote_up+0x603/0x7e0
? __pfx_tmigr_handle_remote_up+0x10/0x10
? sched_balance_trigger+0x1c0/0x9f0
? sched_tick+0x221/0x5a0
? _raw_spin_lock_irq+0x80/0xe0
? __pfx__raw_spin_lock_irq+0x10/0x10
? tick_nohz_handler+0x339/0x440
? __pfx_tmigr_handle_remote_up+0x10/0x10
__walk_groups.isra.0+0x42/0x150
tmigr_handle_remote+0x1f4/0x2e0
? __pfx_tmigr_handle_remote+0x10/0x10
? ktime_get+0x60/0x140
? lapic_next_event+0x11/0x20
? clockevents_program_event+0x1d4/0x2a0
? hrtimer_interrupt+0x322/0x780
handle_softirqs+0x16a/0x550
irq_exit_rcu+0xaf/0xe0
sysvec_apic_timer_interrupt+0x70/0x80
</IRQ>
...
The following diagram reveals the cause of the above warning:
CPU 0 (remove) | CPU 1 (delayed work callback)
mscc_ocelot_remove() |
ocelot_deinit() | ocelot_check_stats_work()
ocelot_stats_deinit() |
cancel_delayed_work()| ...
| queue_delayed_work()
destroy_workqueue() | (wait a time)
| __queue_work() //UAF
The above scenario actually constitutes a UAF vulnerability.
The ocelot_stats_deinit() is only invoked when initialization
failure or resource destruction, so we must ensure that any
delayed work items cannot be rescheduled.
Replace cancel_delayed_work() with disable_delayed_work_sync()
to guarantee proper cancellation of the delayed work item and
ensure completion of any currently executing work before the
workqueue is deallocated.
A deadlock concern was considered: ocelot_stats_deinit() is called
in a process context and is not holding any locks that the delayed
work item might also need. Therefore, the use of the _sync() variant
is safe here.
This bug was identified through static analysis. To reproduce the
issue and validate the fix, I simulated ocelot-switch device by
writing a kernel module and prepared the necessary resources for
the virtual ocelot-switch device's probe process. Then, removing
the virtual device will trigger the mscc_ocelot_remove() function,
which in turn destroys the workqueue.
Fixes: a556c76adc ("net: mscc: Add initial Ocelot switch support")
Signed-off-by: Duoming Zhou <duoming@zju.edu.cn>
Link: https://patch.msgid.link/20251001011149.55073-1-duoming@zju.edu.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Pull pci updates from Bjorn Helgaas:
"Enumeration:
- Add PCI_FIND_NEXT_CAP() and PCI_FIND_NEXT_EXT_CAP() macros that
take config space accessor functions.
Implement pci_find_capability(), pci_find_ext_capability(), and
dwc, dwc endpoint, and cadence capability search interfaces with
them (Hans Zhang)
- Leave parent unit address 0 in 'interrupt-map' so that when we
build devicetree nodes to describe PCI functions that contain
multiple peripherals, we can build this property even when
interrupt controllers lack 'reg' properties (Lorenzo Pieralisi)
- Add a Xeon 6 quirk to disable Extended Tags and limit Max Read
Request Size to 128B to avoid a performance issue (Ilpo Järvinen)
- Add sysfs 'serial_number' file to expose the Device Serial Number
(Matthew Wood)
- Fix pci_acpi_preserve_config() memory leak (Nirmoy Das)
Resource management:
- Align m68k pcibios_enable_device() with other arches (Ilpo
Järvinen)
- Remove sparc pcibios_enable_device() implementations that don't do
anything beyond what pci_enable_resources() does (Ilpo Järvinen)
- Remove mips pcibios_enable_resources() and use
pci_enable_resources() instead (Ilpo Järvinen)
- Clean up bridge window sizing and assignment (Ilpo Järvinen),
including:
- Leave non-claimed bridge windows disabled
- Enable bridges even if a window wasn't assigned because not all
windows are required by downstream devices
- Preserve bridge window type when releasing the resource, since
the type is needed for reassignment
- Consolidate selection of bridge windows into two new
interfaces, pbus_select_window() and
pbus_select_window_for_type(), so this is done consistently
- Compute bridge window start and end earlier to avoid logging
stale information
MSI:
- Add quirk to disable MSI on RDC PCI to PCIe bridges (Marcos Del Sol
Vives)
Error handling:
- Align AER with EEH by allowing drivers to request a Bus Reset on
Non-Fatal Errors (in addition to the reset on Fatal Errors that we
already do) (Lukas Wunner)
- If error recovery fails, emit FAILED_RECOVERY uevents for the
devices, not for the bridge leading to them.
This makes them correspond to BEGIN_RECOVERY uevents (Lukas Wunner)
- Align AER with EEH by calling err_handler.error_detected()
callbacks to notify drivers if error recovery fails (Lukas Wunner)
- Align AER with EEH by restoring device error_state to
pci_channel_io_normal before the err_handler.slot_reset() callback.
This is earlier than before the err_handler.resume() callback
(Lukas Wunner)
- Emit a BEGIN_RECOVERY uevent when driver's
err_handler.error_detected() requests a reset, as well as when it
says recovery is complete or can be done without a reset (Niklas
Schnelle)
- Align s390 with AER and EEH by emitting uevents during error
recovery (Niklas Schnelle)
- Align EEH with AER and s390 by emitting BEGIN_RECOVERY,
SUCCESSFUL_RECOVERY, or FAILED_RECOVERY uevents depending on the
result of err_handler.error_detected() (Niklas Schnelle)
- Fix a NULL pointer dereference in aer_ratelimit() when ACPI GHES
error information identifies a device without an AER Capability
(Breno Leitao)
- Update error decoding and TLP Log printing for new errors in
current PCIe base spec (Lukas Wunner)
- Update error recovery documentation to match the current code
and use consistent nomenclature (Lukas Wunner)
ASPM:
- Enable all ClockPM and ASPM states for devicetree platforms, since
there's typically no firmware that enables ASPM
This is a risky change that may uncover hardware or configuration
defects at boot-time rather than when users enable ASPM via sysfs
later. Booting with "pcie_aspm=off" prevents this enabling
(Manivannan Sadhasivam)
- Remove the qcom code that enabled ASPM (Manivannan Sadhasivam)
Power management:
- If a device has already been disconnected, e.g., by a hotplug
removal, don't bother trying to resume it to D0 when detaching the
driver.
This avoids annoying "Unable to change power state from D3cold to
D0" messages (Mario Limonciello)
- Ensure devices are powered up before config reads for
'max_link_width', 'current_link_speed', 'current_link_width',
'secondary_bus_number', and 'subordinate_bus_number' sysfs files.
This prevents using invalid data (~0) in drivers or lspci and,
depending on how the PCIe controller reports errors, may avoid
error interrupts or crashes (Brian Norris)
Virtualization:
- Add rescan/remove locking when enabling/disabling SR-IOV, which
avoids list corruption on s390, where disabling SR-IOV also
generates hotplug events (Niklas Schnelle)
Peer-to-peer DMA:
- Free struct p2p_pgmap, not a member within it, in the
pci_p2pdma_add_resource() error path (Sungho Kim)
Endpoint framework:
- Document sysfs interface for BAR assignment of vNTB endpoint
functions (Jerome Brunet)
- Fix array underflow in endpoint BAR test case (Dan Carpenter)
- Skip endpoint IRQ test if the IRQ is out of range to avoid false
errors (Christian Bruel)
- Fix endpoint test case for controllers with fixed-size BARs smaller
than requested by the test (Marek Vasut)
- Restore inbound translation when disabling doorbell so the endpoint
doorbell test case can be run more than once (Niklas Cassel)
- Avoid a NULL pointer dereference when releasing DMA channels in
endpoint DMA test case (Shin'ichiro Kawasaki)
- Convert tegra194 interrupt number to MSI vector to fix endpoint
Kselftest MSI_TEST test case (Niklas Cassel)
- Reset tegra194 BARs when running in endpoint mode so the BAR tests
don't overwrite the ATU settings in BAR4 (Niklas Cassel)
- Handle errors in tegra194 BPMP transactions so we don't mistakenly
skip future PERST# assertion (Vidya Sagar)
AMD MDB PCIe controller driver:
- Update DT binding example to separate PERST# to a Root Port stanza
to make multiple Root Ports possible in the future (Sai Krishna
Musham)
- Add driver support for PERST# being described in a Root Port
stanza, falling back to the host bridge if not found there (Sai
Krishna Musham)
Freescale i.MX6 PCIe controller driver:
- Enable the 3.3V Vaux supply if available so devices can request
wakeup with either Beacon or WAKE# (Richard Zhu)
MediaTek PCIe Gen3 controller driver:
- Add optional sys clock ready time setting to avoid sys_clk_rdy
signal glitching in MT6991 and MT8196 (AngeloGioacchino Del Regno)
- Add DT binding and driver support for MT6991 and MT8196
(AngeloGioacchino Del Regno)
NVIDIA Tegra PCIe controller driver:
- When asserting PERST#, disable the controller instead of mistakenly
disabling the PLL twice (Nagarjuna Kristam)
- Convert struct tegra_msi mask_lock to raw spinlock to avoid a lock
nesting error (Marek Vasut)
Qualcomm PCIe controller driver:
- Select PCI Power Control Slot driver so slot voltage rails can be
turned on/off if described in Root Port devicetree node (Qiang Yu)
- Parse only PCI bridge child nodes in devicetree, skipping unrelated
nodes such as OPP (Operating Performance Points), which caused
probe failures (Krishna Chaitanya Chundru)
- Add 8.0 GT/s and 32.0 GT/s equalization settings (Ziyue Zhang)
- Consolidate Root Port 'phy' and 'reset' properties in struct
qcom_pcie_port, regardless of whether we got them from the Root
Port node or the host bridge node (Manivannan Sadhasivam)
- Fetch and map the ELBI register space in the DWC core rather than
in each driver individually (Krishna Chaitanya Chundru)
- Enable ECAM mechanism in DWC core by setting up iATU with 'CFG
Shift Feature' and use this in the qcom driver (Krishna Chaitanya
Chundru)
- Add SM8750 compatible to qcom,pcie-sm8550.yaml (Krishna Chaitanya
Chundru)
- Update qcom,pcie-x1e80100.yaml to allow fifth PCIe host on Qualcomm
Glymur, which is compatible with X1E80100 but doesn't have the
cnoc_sf_axi clock (Qiang Yu)
Renesas R-Car PCIe controller driver:
- Fix a typo that prevented correct PHY initialization (Marek Vasut)
- Add a missing 1ms delay after PWR reset assertion as required by
the V4H manual (Marek Vasut)
- Assure reset has completed before DBI access to avoid SError (Marek
Vasut)
- Fix inverted PHY initialization check, which sometimes led to
timeouts and failure to start the controller (Marek Vasut)
- Pass the correct IRQ domain to generic_handle_domain_irq() to fix a
regression when converting to msi_create_parent_irq_domain()
(Claudiu Beznea)
- Drop the spinlock protecting the PMSR register - it's no longer
required since pci_lock already serializes accesses (Marek Vasut)
- Convert struct rcar_msi mask_lock to raw spinlock to avoid a lock
nesting error (Marek Vasut)
SOPHGO PCIe controller driver:
- Check for existence of struct cdns_pcie.ops before using it to
allow Cadence drivers that don't need to supply ops (Chen Wang)
- Add DT binding and driver for the SOPHGO SG2042 PCIe controller
(Chen Wang)
STMicroelectronics STM32MP25 PCIe controller driver:
- Update pinctrl documentation of initial states and use in runtime
suspend/resume (Christian Bruel)
- Add pinctrl_pm_select_init_state() for use by stm32 driver, which
needs it during resume (Christian Bruel)
- Add devicetree bindings and drivers for the STMicroelectronics
STM32MP25 in host and endpoint modes (Christian Bruel)
Synopsys DesignWare PCIe controller driver:
- Add support for x16 in devicetree 'num-lanes' property (Konrad
Dybcio)
- Verify that if DT specifies a single IRQ for all eDMA channels, it
is named 'dma' (Niklas Cassel)
TI J721E PCIe driver:
- Add MODULE_DEVICE_TABLE() so driver can be autoloaded (Siddharth
Vadapalli)
- Power controller off before configuring the glue layer so the
controller latches the correct values on power-on (Siddharth
Vadapalli)
TI Keystone PCIe controller driver:
- Use devm_request_irq() so 'ks-pcie-error-irq' is freed when driver
exits with error (Siddharth Vadapalli)
- Add Peripheral Virtualization Unit (PVU), which restricts DMA from
PCIe devices to specific regions of host memory, to the ti,am65
binding (Jan Kiszka)
Xilinx NWL PCIe controller driver:
- Clear bootloader E_ECAM_CONTROL before merging in the new driver
value to avoid writing invalid values (Jani Nurminen)"
* tag 'pci-v6.18-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci: (141 commits)
PCI/AER: Avoid NULL pointer dereference in aer_ratelimit()
MAINTAINERS: Add entry for ST STM32MP25 PCIe drivers
PCI: stm32-ep: Add PCIe Endpoint support for STM32MP25
dt-bindings: PCI: Add STM32MP25 PCIe Endpoint bindings
PCI: stm32: Add PCIe host support for STM32MP25
PCI: xilinx-nwl: Fix ECAM programming
PCI: j721e: Fix incorrect error message in probe()
PCI: keystone: Use devm_request_irq() to free "ks-pcie-error-irq" on exit
dt-bindings: PCI: qcom,pcie-x1e80100: Set clocks minItems for the fifth Glymur PCIe Controller
PCI: dwc: Support 16-lane operation
PCI: Add lockdep assertion in pci_stop_and_remove_bus_device()
PCI/IOV: Add PCI rescan-remove locking when enabling/disabling SR-IOV
PCI: rcar-host: Convert struct rcar_msi mask_lock into raw spinlock
PCI: tegra194: Rename 'root_bus' to 'root_port_bus' in tegra_pcie_downstream_dev_to_D0()
PCI: tegra: Convert struct tegra_msi mask_lock into raw spinlock
PCI: rcar-gen4: Fix inverted break condition in PHY initialization
PCI: rcar-gen4: Assure reset occurs before DBI access
PCI: rcar-gen4: Add missing 1ms delay after PWR reset assertion
PCI: Set up bridge resources earlier
PCI: rcar-host: Drop PMSR spinlock
...
Pull virtio updates from Michael Tsirkin:
"Just fixes and cleanups this time around. The mapping cleanups are
preparing the ground for new features, though"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
virtio-vdpa: Drop redundant conversion to bool
vduse: Use fixed 4KB bounce pages for non-4KB page size
vduse: switch to use virtio map API instead of DMA API
vdpa: introduce map ops
vdpa: support virtio_map
virtio: introduce map ops in virtio core
virtio_ring: rename dma_handle to map_handle
virtio: introduce virtio_map container union
virtio: rename dma helpers
virtio_ring: switch to use dma_{map|unmap}_page()
virtio_ring: constify virtqueue pointer for DMA helpers
virtio_balloon: Remove redundant __GFP_NOWARN
vhost: vringh: Fix copy_to_iter return value check
vhost: vringh: Modify the return value check
