Add the usual trampoline functionality from the generic DSA layer down
to the drivers for MST state changes.
When a state changes to disabled/blocking/listening, make sure to fast
age any dynamic entries in the affected VLANs (those controlled by the
MSTI in question).
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add the usual trampoline functionality from the generic DSA layer down
to the drivers for VLAN MSTI migrations.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This is useful for switchdev drivers who are offloading MST states
into hardware. As an example, a driver may wish to flush the FDB for a
port when it transitions from forwarding to blocking - which means
that the previous state must be discoverable.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This is useful for switchdev drivers that might want to refuse to join
a bridge where MST is enabled, if the hardware can't support it.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
br_mst_get_info answers the question: "On this bridge, which VIDs are
mapped to the given MSTI?"
This is useful in switchdev drivers, which might have to fan-out
operations, relating to an MSTI, per VLAN.
An example: When a port's MST state changes from forwarding to
blocking, a driver may choose to flush the dynamic FDB entries on that
port to get faster reconvergence of the network, but this should only
be done in the VLANs that are managed by the MSTI in question.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Generate a switchdev notification whenever an MST state changes. This
notification is keyed by the VLANs MSTI rather than the VID, since
multiple VLANs may share the same MST instance.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Whenever a VLAN moves to a new MSTI, send a switchdev notification so
that switchdevs can track a bridge's VID to MSTI mappings.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Trigger a switchdev event whenever the bridge's MST mode is
enabled/disabled. This allows constituent ports to either perform any
required hardware config, or refuse the change if it not supported.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Make it possible to change the port state in a given MSTI by extending
the bridge port netlink interface (RTM_SETLINK on PF_BRIDGE).The
proposed iproute2 interface would be:
bridge mst set dev <PORT> msti <MSTI> state <STATE>
Current states in all applicable MSTIs can also be dumped via a
corresponding RTM_GETLINK. The proposed iproute interface looks like
this:
$ bridge mst
port msti
vb1 0
state forwarding
100
state disabled
vb2 0
state forwarding
100
state forwarding
The preexisting per-VLAN states are still valid in the MST
mode (although they are read-only), and can be queried as usual if one
is interested in knowing a particular VLAN's state without having to
care about the VID to MSTI mapping (in this example VLAN 20 and 30 are
bound to MSTI 100):
$ bridge -d vlan
port vlan-id
vb1 10
state forwarding mcast_router 1
20
state disabled mcast_router 1
30
state disabled mcast_router 1
40
state forwarding mcast_router 1
vb2 10
state forwarding mcast_router 1
20
state forwarding mcast_router 1
30
state forwarding mcast_router 1
40
state forwarding mcast_router 1
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Allow a VLAN to move out of the CST (MSTI 0), to an independent tree.
The user manages the VID to MSTI mappings via a global VLAN
setting. The proposed iproute2 interface would be:
bridge vlan global set dev br0 vid <VID> msti <MSTI>
Changing the state in non-zero MSTIs is still not supported, but will
be addressed in upcoming changes.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Allow the user to switch from the current per-VLAN STP mode to an MST
mode.
Up to this point, per-VLAN STP states where always isolated from each
other. This is in contrast to the MSTP standard (802.1Q-2018, Clause
13.5), where VLANs are grouped into MST instances (MSTIs), and the
state is managed on a per-MSTI level, rather that at the per-VLAN
level.
Perhaps due to the prevalence of the standard, many switching ASICs
are built after the same model. Therefore, add a corresponding MST
mode to the bridge, which we can later add offloading support for in a
straight-forward way.
For now, all VLANs are fixed to MSTI 0, also called the Common
Spanning Tree (CST). That is, all VLANs will follow the port-global
state.
Upcoming changes will make this actually useful by allowing VLANs to
be mapped to arbitrary MSTIs and allow individual MSTI states to be
changed.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Pull networking fixes from Jakub Kicinski:
"Including fixes from netfilter, ipsec, and wireless.
A few last minute revert / disable and fix patches came down from our
sub-trees. We're not waiting for any fixes at this point.
Current release - regressions:
- Revert "netfilter: nat: force port remap to prevent shadowing
well-known ports", restore working conntrack on asymmetric paths
- Revert "ath10k: drop beacon and probe response which leak from
other channel", restore working AP and mesh mode on QCA9984
- eth: intel: fix hang during reboot/shutdown
Current release - new code bugs:
- netfilter: nf_tables: disable register tracking, it needs more work
to cover all corner cases
Previous releases - regressions:
- ipv6: fix skb_over_panic in __ip6_append_data when (admin-only)
extension headers get specified
- esp6: fix ESP over TCP/UDP, interpret ipv6_skip_exthdr's return
value more selectively
- bnx2x: fix driver load failure when FW not present in initrd
Previous releases - always broken:
- vsock: stop destroying unrelated sockets in nested virtualization
- packet: fix slab-out-of-bounds access in packet_recvmsg()
Misc:
- add Paolo Abeni to networking maintainers!"
* tag 'net-5.17-final' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (26 commits)
iavf: Fix hang during reboot/shutdown
net: mscc: ocelot: fix backwards compatibility with single-chain tc-flower offload
net: bcmgenet: skip invalid partial checksums
bnx2x: fix built-in kernel driver load failure
net: phy: mscc: Add MODULE_FIRMWARE macros
net: dsa: Add missing of_node_put() in dsa_port_parse_of
net: handle ARPHRD_PIMREG in dev_is_mac_header_xmit()
Revert "ath10k: drop beacon and probe response which leak from other channel"
hv_netvsc: Add check for kvmalloc_array
iavf: Fix double free in iavf_reset_task
ice: destroy flow director filter mutex after releasing VSIs
ice: fix NULL pointer dereference in ice_update_vsi_tx_ring_stats()
Add Paolo Abeni to networking maintainers
atm: eni: Add check for dma_map_single
net/packet: fix slab-out-of-bounds access in packet_recvmsg()
net: mdio: mscc-miim: fix duplicate debugfs entry
net: phy: marvell: Fix invalid comparison in the resume and suspend functions
esp6: fix check on ipv6_skip_exthdr's return value
net: dsa: microchip: add spi_device_id tables
netfilter: nf_tables: disable register tracking
...
This patch adds support for encapsulating IPv4/IPv6 within GENEVE.
In order to use this, a new IFLA_GENEVE_INNER_PROTO_INHERIT flag needs
to be provided at device creation. This property cannot be changed for
the time being.
In case IP traffic is received on a non-tun device the drop count is
increased.
Signed-off-by: Eyal Birger <eyal.birger@gmail.com>
Link: https://lore.kernel.org/r/20220316061557.431872-1-eyal.birger@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Add vlan push_eth and pop_eth action to the hardware intermediate
representation model which would subsequently allow it to be used
by drivers for offload.
Signed-off-by: Maor Dickman <maord@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Now that devlink ports are protected by the instance lock
it seems natural to pass devlink_port as an argument to
the port_split / port_unsplit callbacks.
This should save the drivers from doing a lookup.
In theory drivers may have supported unsplitting ports
which were not registered prior to this change.
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Tested-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
It should be familiar and beneficial to expose devlink instance
lock to the drivers. This way drivers can block devlink from
calling them during critical sections without breakneck locking.
Add port helpers, port splitting callbacks will be the first
target.
Use 'devl_' prefix for "explicitly locked" API. Initial RFC used
'__devlink' but that's too much typing.
devl_lock_is_held() is not defined without lockdep, which is
the same behavior as lockdep_is_held() itself.
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The fundamental premise of VRF and l3mdev core code is binding a socket
to a device (l3mdev or netdev with an L3 domain) to indicate L3 scope.
Legacy code resets flowi_oif to the l3mdev losing any original port
device binding. Ben (among others) has demonstrated use cases where the
original port device binding is important and needs to be retained.
This patch handles that by adding a new entry to the common flow struct
that can indicate the l3mdev index for later rule and table matching
avoiding the need to reset flowi_oif.
In addition to allowing more use cases that require port device binds,
this patch brings a few datapath simplications:
1. l3mdev_fib_rule_match is only called when walking fib rules and
always after l3mdev_update_flow. That allows an optimization to bail
early for non-VRF type uses cases when flowi_l3mdev is not set. Also,
only that index needs to be checked for the FIB table id.
2. l3mdev_update_flow can be called with flowi_oif set to a l3mdev
(e.g., VRF) device. By resetting flowi_oif only for this case the
FLOWI_FLAG_SKIP_NH_OIF flag is not longer needed and can be removed,
removing several checks in the datapath. The flowi_iif path can be
simplified to only be called if the it is not loopback (loopback can
not be assigned to an L3 domain) and the l3mdev index is not already
set.
3. Avoid another device lookup in the output path when the fib lookup
returns a reject failure.
Note: 2 functional tests for local traffic with reject fib rules are
updated to reflect the new direct failure at FIB lookup time for ping
rather than the failure on packet path. The current code fails like this:
HINT: Fails since address on vrf device is out of device scope
COMMAND: ip netns exec ns-A ping -c1 -w1 -I eth1 172.16.3.1
ping: Warning: source address might be selected on device other than: eth1
PING 172.16.3.1 (172.16.3.1) from 172.16.3.1 eth1: 56(84) bytes of data.
--- 172.16.3.1 ping statistics ---
1 packets transmitted, 0 received, 100% packet loss, time 0ms
where the test now directly fails:
HINT: Fails since address on vrf device is out of device scope
COMMAND: ip netns exec ns-A ping -c1 -w1 -I eth1 172.16.3.1
ping: connect: No route to host
Signed-off-by: David Ahern <dsahern@kernel.org>
Tested-by: Ben Greear <greearb@candelatech.com>
Link: https://lore.kernel.org/r/20220314204551.16369-1-dsahern@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contains Netfilter fixes for net coming late
in the 5.17-rc process:
1) Revert port remap to mitigate shadowing service ports, this is causing
problems in existing setups and this mitigation can be achieved with
explicit ruleset, eg.
... tcp sport < 16386 tcp dport >= 32768 masquerade random
This patches provided a built-in policy similar to the one described above.
2) Disable register tracking infrastructure in nf_tables. Florian reported
two issues:
- Existing expressions with no implemented .reduce interface
that causes data-store on register should cancel the tracking.
- Register clobbering might be possible storing data on registers that
are larger than 32-bits.
This might lead to generating incorrect ruleset bytecode. These two
issues are scheduled to be addressed in the next release cycle.
* git://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf:
netfilter: nf_tables: disable register tracking
Revert "netfilter: conntrack: tag conntracks picked up in local out hook"
Revert "netfilter: nat: force port remap to prevent shadowing well-known ports"
====================
Link: https://lore.kernel.org/r/20220312220315.64531-1-pablo@netfilter.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Follow the established programming model for this driver and provide
shims in the felix DSA driver which call the implementations from the
ocelot switch lib. The ocelot switchdev driver wasn't integrated with
dcbnl due to lack of hardware availability.
The switch doesn't have any fancy QoS classification enabled by default.
The provided getters will create a default-prio app table entry of 0,
and no dscp entry. However, the getters have been made to actually
retrieve the hardware configuration rather than static values, to be
future proof in case DSA will need this information from more call paths.
For default-prio, there is a single field per port, in ANA_PORT_QOS_CFG,
called QOS_DEFAULT_VAL.
DSCP classification is enabled per-port, again via ANA_PORT_QOS_CFG
(field QOS_DSCP_ENA), and individual DSCP values are configured as
trusted or not through register ANA_DSCP_CFG (replicated 64 times).
An untrusted DSCP value falls back to other QoS classification methods.
If trusted, the selected ANA_DSCP_CFG register also holds the QoS class
in the QOS_DSCP_VAL field.
The hardware also supports DSCP remapping (DSCP value X is translated to
DSCP value Y before the QoS class is determined based on the app table
entry for Y) and DSCP packet rewriting. The dcbnl framework, for being
so flexible in other useless areas, doesn't appear to support this.
So this functionality has been left out.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similar to the port-based default priority, IEEE 802.1Q-2018 allows the
Application Priority Table to define QoS classes (0 to 7) per IP DSCP
value (0 to 63).
In the absence of an app table entry for a packet with DSCP value X,
QoS classification for that packet falls back to other methods (VLAN PCP
or port-based default). The presence of an app table for DSCP value X
with priority Y makes the hardware classify the packet to QoS class Y.
As opposed to the default-prio where DSA exposes only a "set" in
dsa_switch_ops (because the port-based default is the fallback, it
always exists, either implicitly or explicitly), for DSCP priorities we
expose an "add" and a "del". The addition of a DSCP entry means trusting
that DSCP priority, the deletion means ignoring it.
Drivers that already trust (at least some) DSCP values can describe
their configuration in dsa_switch_ops :: port_get_dscp_prio(), which is
called for each DSCP value from 0 to 63.
Again, there can be more than one dcbnl app table entry for the same
DSCP value, DSA chooses the one with the largest configured priority.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The port-based default QoS class is assigned to packets that lack a
VLAN PCP (or the port is configured to not trust the VLAN PCP),
an IP DSCP (or the port is configured to not trust IP DSCP), and packets
on which no tc-skbedit action has matched.
Similar to other drivers, this can be exposed to user space using the
DCB Application Priority Table. IEEE 802.1Q-2018 specifies in Table
D-8 - Sel field values that when the Selector is 1, the Protocol ID
value of 0 denotes the "Default application priority. For use when
application priority is not otherwise specified."
The way in which the dcbnl integration in DSA has been designed has to
do with its requirements. Andrew Lunn explains that SOHO switches are
expected to come with some sort of pre-configured QoS profile, and that
it is desirable for this to come pre-loaded into the DSA slave interfaces'
DCB application priority table.
In the dcbnl design, this is possible because calls to dcb_ieee_setapp()
can be initiated by anyone including being self-initiated by this device
driver.
However, what makes this challenging to implement in DSA is that the DSA
core manages the net_devices (effectively hiding them from drivers),
while drivers manage the hardware. The DSA core has no knowledge of what
individual drivers' QoS policies are. DSA could export to drivers a
wrapper over dcb_ieee_setapp() and these could call that function to
pre-populate the app priority table, however drivers don't have a good
moment in time to do this. The dsa_switch_ops :: setup() method gets
called before the net_devices are created (dsa_slave_create), and so is
dsa_switch_ops :: port_setup(). What remains is dsa_switch_ops ::
port_enable(), but this gets called upon each ndo_open. If we add app
table entries on every open, we'd need to remove them on close, to avoid
duplicate entry errors. But if we delete app priority entries on close,
what we delete may not be the initial, driver pre-populated entries, but
rather user-added entries.
So it is clear that letting drivers choose the timing of the
dcb_ieee_setapp() call is inappropriate. The alternative which was
chosen is to introduce hardware-specific ops in dsa_switch_ops, and
effectively hide dcbnl details from drivers as well. For pre-populating
the application table, dsa_slave_dcbnl_init() will call
ds->ops->port_get_default_prio() which is supposed to read from
hardware. If the operation succeeds, DSA creates a default-prio app
table entry. The method is called as soon as the slave_dev is
registered, but before we release the rtnl_mutex. This is done such that
user space sees the app table entries as soon as it sees the interface
being registered.
The fact that we populate slave_dev->dcbnl_ops with a non-NULL pointer
changes behavior in dcb_doit() from net/dcb/dcbnl.c, which used to
return -EOPNOTSUPP for any dcbnl operation where netdev->dcbnl_ops is
NULL. Because there are still dcbnl-unaware DSA drivers even if they
have dcbnl_ops populated, the way to restore the behavior is to make all
dcbnl_ops return -EOPNOTSUPP on absence of the hardware-specific
dsa_switch_ops method.
The dcbnl framework absurdly allows there to be more than one app table
entry for the same selector and protocol (in other words, more than one
port-based default priority). In the iproute2 dcb program, there is a
"replace" syntactical sugar command which performs an "add" and a "del"
to hide this away. But we choose the largest configured priority when we
call ds->ops->port_set_default_prio(), using __fls(). When there is no
default-prio app table entry left, the port-default priority is restored
to 0.
Link: https://patchwork.kernel.org/project/netdevbpf/patch/20210113154139.1803705-2-olteanv@gmail.com/
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
____napi_schedule() needs to be invoked with disabled interrupts due to
__raise_softirq_irqoff (in order not to corrupt the per-CPU list).
____napi_schedule() needs also to be invoked from an interrupt context
so that the raised-softirq is processed while the interrupt context is
left.
Add lockdep asserts for both conditions.
While this is the second time the irq/softirq check is needed, provide a
generic lockdep_assert_softirq_will_run() which is used by both caller.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tony Nguyen says:
====================
ice: GTP support in switchdev
Marcin Szycik says:
Add support for adding GTP-C and GTP-U filters in switchdev mode.
To create a filter for GTP, create a GTP-type netdev with ip tool, enable
hardware offload, add qdisc and add a filter in tc:
ip link add $GTP0 type gtp role <sgsn/ggsn> hsize <hsize>
ethtool -K $PF0 hw-tc-offload on
tc qdisc add dev $GTP0 ingress
tc filter add dev $GTP0 ingress prio 1 flower enc_key_id 1337 \
action mirred egress redirect dev $VF1_PR
By default, a filter for GTP-U will be added. To add a filter for GTP-C,
specify enc_dst_port = 2123, e.g.:
tc filter add dev $GTP0 ingress prio 1 flower enc_key_id 1337 \
enc_dst_port 2123 action mirred egress redirect dev $VF1_PR
Note: outer IPv6 offload is not supported yet.
Note: GTP-U with no payload offload is not supported yet.
ICE COMMS package is required to create a filter as it contains GTP
profiles.
Changes in iproute2 [1] are required to be able to add GTP netdev and use
GTP-specific options (QFI and PDU type).
[1] https://lore.kernel.org/netdev/20220211182902.11542-1-wojciech.drewek@intel.com/T
---
v2: Add more CC
v3: Fix mail thread, sorry for spam
v4: Add GTP echo response in gtp module
v5: Change patch order
v6: Add GTP echo request in gtp module
v7: Fix kernel-docs in ice
v8: Remove handling of GTP Echo Response
v9: Add sending of multicast message on GTP Echo Response, fix GTP-C dummy
packet selection
v10: Rebase, fixed most 80 char line limits
v11: Rebase, collect Harald's Reviewed-by on patch 3
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Before adding yet another possibly contended atomic_long_t,
it is time to add per-cpu storage for existing ones:
dev->tx_dropped, dev->rx_dropped, and dev->rx_nohandler
Because many devices do not have to increment such counters,
allocate the per-cpu storage on demand, so that dev_get_stats()
does not have to spend considerable time folding zero counters.
Note that some drivers have abused these counters which
were supposed to be only used by core networking stack.
v4: should use per_cpu_ptr() in dev_get_stats() (Jakub)
v3: added a READ_ONCE() in netdev_core_stats_alloc() (Paolo)
v2: add a missing include (reported by kernel test robot <lkp@intel.com>)
Change in netdev_core_stats_alloc() (Jakub)
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: jeffreyji <jeffreyji@google.com>
Reviewed-by: Brian Vazquez <brianvv@google.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Link: https://lore.kernel.org/r/20220311051420.2608812-1-eric.dumazet@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When iterating over sockets using vsock_for_each_connected_socket, make
sure that a transport filters out sockets that don't belong to the
transport.
There actually was an issue caused by this; in a nested VM
configuration, destroying the nested VM (which often involves the
closing of /dev/vhost-vsock if there was h2g connections to the nested
VM) kills not only the h2g connections, but also all existing g2h
connections to the (outmost) host which are totally unrelated.
Tested: Executed the following steps on Cuttlefish (Android running on a
VM) [1]: (1) Enter into an `adb shell` session - to have a g2h
connection inside the VM, (2) open and then close /dev/vhost-vsock by
`exec 3< /dev/vhost-vsock && exec 3<&-`, (3) observe that the adb
session is not reset.
[1] https://android.googlesource.com/device/google/cuttlefish/
Fixes: c0cfa2d8a7 ("vsock: add multi-transports support")
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jiyong Park <jiyong@google.com>
Link: https://lore.kernel.org/r/20220311020017.1509316-1-jiyong@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Enable binding the nfp driver to NFP3800 and NFP3803 devices.
The PCIE_SRAM offset is different for the NFP3800 device, which also
only supports a single explicit group.
Changes to Dirk's work:
* 48-bit dma addressing is not ready yet. Keep 40-bit dma addressing
for NFP3800.
Signed-off-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Fei Qin <fei.qin@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Johannes Berg says:
====================
brcmfmac
* add BCM43454/6 support
rtw89
* add support for 160 MHz channels and 6 GHz band
* hardware scan support
iwlwifi
* support UHB TAS enablement via BIOS
* remove a bunch of W=1 warnings
* add support for channel switch offload
* support 32 Rx AMPDU sessions in newer devices
* add support for a couple of new devices
* add support for band disablement via BIOS
mt76
* mt7915 thermal management improvements
* SAR support for more mt76 drivers
* mt7986 wmac support on mt7915
ath11k
* debugfs interface to configure firmware debug log level
* debugfs interface to test Target Wake Time (TWT)
* provide 802.11ax High Efficiency (HE) data via radiotap
ath9k
* use hw_random API instead of directly dumping into random.c
wcn36xx
* fix wcn3660 to work on 5 GHz band
ath6kl
* add device ID for WLU5150-D81
cfg80211/mac80211
* initial EHT (from 802.11be) support
(EHT rates, 320 MHz, larger block-ack)
* support disconnect on HW restart
* tag 'wireless-next-2022-03-11' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next: (247 commits)
mac80211: Add support to trigger sta disconnect on hardware restart
mac80211: fix potential double free on mesh join
mac80211: correct legacy rates check in ieee80211_calc_rx_airtime
nl80211: fix typo of NL80211_IF_TYPE_OCB in documentation
mac80211: Use GFP_KERNEL instead of GFP_ATOMIC when possible
mac80211: replace DEFINE_SIMPLE_ATTRIBUTE with DEFINE_DEBUGFS_ATTRIBUTE
rtw89: 8852c: process logic efuse map
rtw89: 8852c: process efuse of phycap
rtw89: support DAV efuse reading operation
rtw89: 8852c: add chip::dle_mem
rtw89: add page_regs to handle v1 chips
rtw89: add chip_info::{h2c,c2h}_reg to support more chips
rtw89: add hci_func_en_addr to support variant generation
rtw89: add power_{on/off}_func
rtw89: read chip version depends on chip ID
rtw89: pci: use a struct to describe all registers address related to DMA channel
rtw89: pci: add V1 of PCI channel address
rtw89: pci: add struct rtw89_pci_info
rtw89: 8852c: add 8852c empty files
MAINTAINERS: add devicetree bindings entry for mt76
...
====================
Link: https://lore.kernel.org/r/20220311124029.213470-1-johannes@sipsolutions.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Merge misc fixes from David Howells:
"A set of patches for watch_queue filter issues noted by Jann. I've
added in a cleanup patch from Christophe Jaillet to convert to using
formal bitmap specifiers for the note allocation bitmap.
Also two filesystem fixes (afs and cachefiles)"
* emailed patches from David Howells <dhowells@redhat.com>:
cachefiles: Fix volume coherency attribute
afs: Fix potential thrashing in afs writeback
watch_queue: Make comment about setting ->defunct more accurate
watch_queue: Fix lack of barrier/sync/lock between post and read
watch_queue: Free the alloc bitmap when the watch_queue is torn down
watch_queue: Fix the alloc bitmap size to reflect notes allocated
watch_queue: Use the bitmap API when applicable
watch_queue: Fix to always request a pow-of-2 pipe ring size
watch_queue: Fix to release page in ->release()
watch_queue, pipe: Free watchqueue state after clearing pipe ring
watch_queue: Fix filter limit check
A network filesystem may set coherency data on a volume cookie, and if
given, cachefiles will store this in an xattr on the directory in the
cache corresponding to the volume.
The function that sets the xattr just stores the contents of the volume
coherency buffer directly into the xattr, with nothing added; the
checking function, on the other hand, has a cut'n'paste error whereby it
tries to interpret the xattr contents as would be the xattr on an
ordinary file (using the cachefiles_xattr struct). This results in a
failure to match the coherency data because the buffer ends up being
shifted by 18 bytes.
Fix this by defining a structure specifically for the volume xattr and
making both the setting and checking functions use it.
Since the volume coherency doesn't work if used, take the opportunity to
insert a reserved field for future use, set it to 0 and check that it is
0. Log mismatch through the appropriate tracepoint.
Note that this only affects cifs; 9p, afs, ceph and nfs don't use the
volume coherency data at the moment.
Fixes: 32e150037d ("fscache, cachefiles: Store the volume coherency data")
Reported-by: Rohith Surabattula <rohiths.msft@gmail.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: Jeff Layton <jlayton@kernel.org>
cc: Steve French <smfrench@gmail.com>
cc: linux-cifs@vger.kernel.org
cc: linux-cachefs@redhat.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In watch_queue_set_filter(), there are a couple of places where we check
that the filter type value does not exceed what the type_filter bitmap
can hold. One place calculates the number of bits by:
if (tf[i].type >= sizeof(wfilter->type_filter) * 8)
which is fine, but the second does:
if (tf[i].type >= sizeof(wfilter->type_filter) * BITS_PER_LONG)
which is not. This can lead to a couple of out-of-bounds writes due to
a too-large type:
(1) __set_bit() on wfilter->type_filter
(2) Writing more elements in wfilter->filters[] than we allocated.
Fix this by just using the proper WATCH_TYPE__NR instead, which is the
number of types we actually know about.
The bug may cause an oops looking something like:
BUG: KASAN: slab-out-of-bounds in watch_queue_set_filter+0x659/0x740
Write of size 4 at addr ffff88800d2c66bc by task watch_queue_oob/611
...
Call Trace:
<TASK>
dump_stack_lvl+0x45/0x59
print_address_description.constprop.0+0x1f/0x150
...
kasan_report.cold+0x7f/0x11b
...
watch_queue_set_filter+0x659/0x740
...
__x64_sys_ioctl+0x127/0x190
do_syscall_64+0x43/0x90
entry_SYSCALL_64_after_hwframe+0x44/0xae
Allocated by task 611:
kasan_save_stack+0x1e/0x40
__kasan_kmalloc+0x81/0xa0
watch_queue_set_filter+0x23a/0x740
__x64_sys_ioctl+0x127/0x190
do_syscall_64+0x43/0x90
entry_SYSCALL_64_after_hwframe+0x44/0xae
The buggy address belongs to the object at ffff88800d2c66a0
which belongs to the cache kmalloc-32 of size 32
The buggy address is located 28 bytes inside of
32-byte region [ffff88800d2c66a0, ffff88800d2c66c0)
Fixes: c73be61ced ("pipe: Add general notification queue support")
Reported-by: Jann Horn <jannh@google.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Options are as follows: PDU_TYPE:QFI and they refernce to
the fields from the PDU Session Protocol. PDU Session data
is conveyed in GTP-U Extension Header.
GTP-U Extension Header is described in 3GPP TS 29.281.
PDU Session Protocol is described in 3GPP TS 38.415.
PDU_TYPE - indicates the type of the PDU Session Information (4 bits)
QFI - QoS Flow Identifier (6 bits)
# ip link add gtp_dev type gtp role sgsn
# tc qdisc add dev gtp_dev ingress
# tc filter add dev gtp_dev protocol ip parent ffff: \
flower \
enc_key_id 11 \
gtp_opts 1:8/ff:ff \
action mirred egress redirect dev eth0
Signed-off-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Adding GTP device through ip link creates the situation where
GTP instance is not able to send GTP echo requests.
Echo requests are used to check if GTP peer is still alive.
With this patch, gtp_genl_ops are extended by new cmd (GTP_CMD_ECHOREQ)
which allows to send echo request in the given version of GTP
protocol (v0 or v1), from the given ms address to he given
peer. TID is not inclued because in all path management
messages it should be equal to 0.
When GTP echo response is detected, multicast message is
send to everyone in the gtp_genl_family. Message contains
GTP version, ms address and peer address.
Suggested-by: Harald Welte <laforge@gnumonks.org>
Signed-off-by: Wojciech Drewek <wojciech.drewek@intel.com>
Reviewed-by: Harald Welte <laforge@gnumonks.org>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Adding GTP device through ip link creates the situation where
there is no userspace daemon which would handle GTP messages
(Echo Request for example). GTP-U instance which would not respond
to echo requests would violate GTP specification.
When GTP packet arrives with GTP_ECHO_REQ message type,
GTP_ECHO_RSP is send to the sender. GTP_ECHO_RSP message
should contain information element with GTPIE_RECOVERY tag and
restart counter value. For GTPv1 restart counter is not used
and should be equal to 0, for GTPv0 restart counter contains
information provided from userspace(IFLA_GTP_RESTART_COUNT).
Signed-off-by: Wojciech Drewek <wojciech.drewek@intel.com>
Suggested-by: Harald Welte <laforge@gnumonks.org>
Reviewed-by: Harald Welte <laforge@gnumonks.org>
Tested-by: Harald Welte <laforge@gnumonks.org>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Currently, when the user wants to create GTP device, he has to
provide file handles to the sockets created in userspace (IFLA_GTP_FD0,
IFLA_GTP_FD1). This behaviour is not ideal, considering the option of
adding support for GTP device creation through ip link. Ip link
application is not a good place to create such sockets.
This patch allows to create GTP device without providing
IFLA_GTP_FD0 and IFLA_GTP_FD1 arguments. If the user sets
IFLA_GTP_CREATE_SOCKETS attribute, then GTP module takes care
of creating UDP sockets by itself. Sockets are created with the
commonly known UDP ports used for GTP protocol (GTP0_PORT and
GTP1U_PORT). In this case we don't have to provide encap_destroy
because no extra deinitialization is needed, everything is covered
by udp_tunnel_sock_release.
Note: GTP instance created with only this change applied, does
not handle GTP Echo Requests. This is implemented in the following
patch.
Signed-off-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Currently in case of target hardware restart, we just reconfig and
re-enable the security keys and enable the network queues to start
data traffic back from where it was interrupted.
Many ath10k wifi chipsets have sequence numbers for the data
packets assigned by firmware and the mac sequence number will
restart from zero after target hardware restart leading to mismatch
in the sequence number expected by the remote peer vs the sequence
number of the frame sent by the target firmware.
This mismatch in sequence number will cause out-of-order packets
on the remote peer and all the frames sent by the device are dropped
until we reach the sequence number which was sent before we restarted
the target hardware
In order to fix this, we trigger a sta disconnect, in case of target
hw restart. After this there will be a fresh connection and thereby
avoiding the dropping of frames by remote peer.
The right fix would be to pull the entire data path into the host
which is not feasible or would need lots of complex changes and
will still be inefficient.
Tested on ath10k using WCN3990, QCA6174
Signed-off-by: Youghandhar Chintala <youghand@codeaurora.org>
Link: https://lore.kernel.org/r/20220308115325.5246-2-youghand@codeaurora.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Today's implementation of csum_shift() leads to branching based on
parity of 'offset'
000002f8 <csum_block_add>:
2f8: 70 a5 00 01 andi. r5,r5,1
2fc: 41 a2 00 08 beq 304 <csum_block_add+0xc>
300: 54 84 c0 3e rotlwi r4,r4,24
304: 7c 63 20 14 addc r3,r3,r4
308: 7c 63 01 94 addze r3,r3
30c: 4e 80 00 20 blr
Use first bit of 'offset' directly as input of the rotation instead of
branching.
000002f8 <csum_block_add>:
2f8: 54 a5 1f 38 rlwinm r5,r5,3,28,28
2fc: 20 a5 00 20 subfic r5,r5,32
300: 5c 84 28 3e rotlw r4,r4,r5
304: 7c 63 20 14 addc r3,r3,r4
308: 7c 63 01 94 addze r3,r3
30c: 4e 80 00 20 blr
And change to left shift instead of right shift to skip one more
instruction. This has no impact on the final sum.
000002f8 <csum_block_add>:
2f8: 54 a5 1f 38 rlwinm r5,r5,3,28,28
2fc: 5c 84 28 3e rotlw r4,r4,r5
300: 7c 63 20 14 addc r3,r3,r4
304: 7c 63 01 94 addze r3,r3
308: 4e 80 00 20 blr
Seems like only powerpc benefits from a branchless implementation.
Other main architectures like ARM or X86 get better code with
the generic implementation and its branch.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
The assumption that the first byte in the module mapping dword is the
module number shouldn't be hard-coded in the driver, but come from
mlx5_ifc structs.
While at it, fix the incorrect width for the 'rx_lane' and 'tx_lane'
fields.
Signed-off-by: Gal Pressman <gal@nvidia.com>
Reviewed-by: Maxim Mikityanskiy <maximmi@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
The MCIA register supports either 12 or 32 dwords, use the correct value
by querying the capability from the MCAM register.
Signed-off-by: Gal Pressman <gal@nvidia.com>
Reviewed-by: Maxim Mikityanskiy <maximmi@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Few years ago OVS user space made a strange choice in the commit [1]
to define types only valid for the user space inside the copy of a
kernel uAPI header. '#ifndef __KERNEL__' and another attribute was
added later.
This leads to the inevitable clash between user space and kernel types
when the kernel uAPI is extended. The issue was unveiled with the
addition of a new type for IPv6 extension header in kernel uAPI.
When kernel provides the OVS_KEY_ATTR_IPV6_EXTHDRS attribute to the
older user space application, application tries to parse it as
OVS_KEY_ATTR_PACKET_TYPE and discards the whole netlink message as
malformed. Since OVS_KEY_ATTR_IPV6_EXTHDRS is supplied along with
every IPv6 packet that goes to the user space, IPv6 support is fully
broken.
Fixing that by bringing these user space attributes to the kernel
uAPI to avoid the clash. Strictly speaking this is not the problem
of the kernel uAPI, but changing it is the only way to avoid breakage
of the older user space applications at this point.
These 2 types are explicitly rejected now since they should not be
passed to the kernel. Additionally, OVS_KEY_ATTR_TUNNEL_INFO moved
out from the '#ifdef __KERNEL__' as there is no good reason to hide
it from the userspace. And it's also explicitly rejected now, because
it's for in-kernel use only.
Comments with warnings were added to avoid the problem coming back.
(1 << type) converted to (1ULL << type) to avoid integer overflow on
OVS_KEY_ATTR_IPV6_EXTHDRS, since it equals 32 now.
[1] beb75a40fdc2 ("userspace: Switching of L3 packets in L2 pipeline")
Fixes: 28a3f06017 ("net: openvswitch: IPv6: Add IPv6 extension header support")
Link: https://lore.kernel.org/netdev/3adf00c7-fe65-3ef4-b6d7-6d8a0cad8a5f@nvidia.com
Link: beb75a40fd
Reported-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Ilya Maximets <i.maximets@ovn.org>
Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: Aaron Conole <aconole@redhat.com>
Link: https://lore.kernel.org/r/20220309222033.3018976-1-i.maximets@ovn.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Marc Kleine-Budde says:
====================
pull-request: can-next 2022-03-10
The first 3 patches are by Oliver Hartkopp, target the CAN ISOTP
protocol and update the CAN frame sending behavior, and increases the
max PDU size to 64 kByte.
The next 2 patches are also by Oliver Hartkopp and update the virtual
VXCAN driver so that CAN frames send into the peer name space show up
as RX'ed CAN frames.
Vincent Mailhol contributes a patch for the etas_es58x driver to fix a
false positive dereference uninitialized variable warning.
2 patches by Ulrich Hecht add r8a779a0 SoC support to the rcar_canfd
driver.
The remaining 21 patches target the gs_usb driver and are by Peter
Fink, Ben Evans, Eric Evenchick and me. This series cleans up the
gs-usb driver, documents some bits of the USB ABI used by the widely
used open source firmware candleLight, adds support for up to 3 CAN
interfaces per USB device, adds CAN-FD support, adds quirks for some
hardware and software workarounds and finally adds support for 2 new
devices.
* tag 'linux-can-next-for-5.18-20220310' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next: (29 commits)
can: gs_usb: add VID/PID for ABE CAN Debugger devices
can: gs_usb: add VID/PID for CES CANext FD devices
can: gs_usb: add extended bt_const feature
can: gs_usb: activate quirks for CANtact Pro unconditionally
can: gs_usb: add quirk for CANtact Pro overlapping GS_USB_BREQ value
can: gs_usb: add usb quirk for NXP LPC546xx controllers
can: gs_usb: add CAN-FD support
can: gs_usb: use union and FLEX_ARRAY for data in struct gs_host_frame
can: gs_usb: support up to 3 channels per device
can: gs_usb: gs_usb_probe(): introduce udev and make use of it
can: gs_usb: document the PAD_PKTS_TO_MAX_PKT_SIZE feature
can: gs_usb: document the USER_ID feature
can: gs_usb: update GS_CAN_FEATURE_IDENTIFY documentation
can: gs_usb: add HW timestamp mode bit
can: gs_usb: gs_make_candev(): call SET_NETDEV_DEV() after handling all bt_const->feature
can: gs_usb: rewrap usb_control_msg() and usb_fill_bulk_urb()
can: gs_usb: rewrap error messages
can: gs_usb: GS_CAN_FLAG_OVERFLOW: make use of BIT()
can: gs_usb: sort include files alphabetically
can: gs_usb: fix checkpatch warning
...
====================
Link: https://lore.kernel.org/r/20220310142903.341658-1-mkl@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Pull networking fixes from Jakub Kicinski:
"Including fixes from bluetooth, and ipsec.
Current release - regressions:
- Bluetooth: fix unbalanced unlock in set_device_flags()
- Bluetooth: fix not processing all entries on cmd_sync_work, make
connect with qualcomm and intel adapters reliable
- Revert "xfrm: state and policy should fail if XFRMA_IF_ID 0"
- xdp: xdp_mem_allocator can be NULL in trace_mem_connect()
- eth: ice: fix race condition and deadlock during interface enslave
Current release - new code bugs:
- tipc: fix incorrect order of state message data sanity check
Previous releases - regressions:
- esp: fix possible buffer overflow in ESP transformation
- dsa: unlock the rtnl_mutex when dsa_master_setup() fails
- phy: meson-gxl: fix interrupt handling in forced mode
- smsc95xx: ignore -ENODEV errors when device is unplugged
Previous releases - always broken:
- xfrm: fix tunnel mode fragmentation behavior
- esp: fix inter address family tunneling on GSO
- tipc: fix null-deref due to race when enabling bearer
- sctp: fix kernel-infoleak for SCTP sockets
- eth: macb: fix lost RX packet wakeup race in NAPI receive
- eth: intel stop disabling VFs due to PF error responses
- eth: bcmgenet: don't claim WOL when its not available"
* tag 'net-5.17-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (50 commits)
xdp: xdp_mem_allocator can be NULL in trace_mem_connect().
ice: Fix race condition during interface enslave
net: phy: meson-gxl: improve link-up behavior
net: bcmgenet: Don't claim WOL when its not available
net: arc_emac: Fix use after free in arc_mdio_probe()
sctp: fix kernel-infoleak for SCTP sockets
net: phy: correct spelling error of media in documentation
net: phy: DP83822: clear MISR2 register to disable interrupts
gianfar: ethtool: Fix refcount leak in gfar_get_ts_info
selftests: pmtu.sh: Kill nettest processes launched in subshell.
selftests: pmtu.sh: Kill tcpdump processes launched by subshell.
NFC: port100: fix use-after-free in port100_send_complete
net/mlx5e: SHAMPO, reduce TIR indication
net/mlx5e: Lag, Only handle events from highest priority multipath entry
net/mlx5: Fix offloading with ESWITCH_IPV4_TTL_MODIFY_ENABLE
net/mlx5: Fix a race on command flush flow
net/mlx5: Fix size field in bufferx_reg struct
ax25: Fix NULL pointer dereference in ax25_kill_by_device
net: marvell: prestera: Add missing of_node_put() in prestera_switch_set_base_mac_addr
net: ethernet: lpc_eth: Handle error for clk_enable
...
Saeed Mahameed says:
====================
mlx5-updates-2022-03-09
1) Remove kernel log prints on FW events regarding FW pages management
and replace that with debugfs entries to track FW pages management commands
failures and general stats, we do that for all FW commands in general since
it's the same effort to do so under the already existing debugfs entry for
FW commands.
2) Add support for ConnectX-7 Software managed steering, in other words STEv2
which shares a lot in common with STE V1, the difference is in specific
offsets in the devices, the logic is almost the same, thus we implement
STEv1 and STEv2 in the same file.
* tag 'mlx5-updates-2022-03-09' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux:
net/mlx5: DR, Add support for ConnectX-7 steering
net/mlx5: DR, Refactor ste_ctx handling for STE v0/1
net/mlx5: DR, Rename action modify fields to reflect naming in HW spec
net/mlx5: DR, Fix handling of different actions on the same STE in STEv1
net/mlx5: DR, Remove unneeded comments
net/mlx5: DR, Add support for matching on Internet Header Length (IHL)
net/mlx5: DR, Align mlx5dv_dr API vport action with FW behavior
net/mlx5: Add debugfs counters for page commands failures
net/mlx5: Add pages debugfs
net/mlx5: Move debugfs entries to separate struct
net/mlx5: Change release_all_pages cap bit location
net/mlx5: Remove redundant error on reclaim pages
net/mlx5: Remove redundant error on give pages
net/mlx5: Remove redundant notify fail on give pages
net/mlx5: Add command failures data to debugfs
net/mlx5e: TC, Fix use after free in mlx5e_clone_flow_attr_for_post_act()
====================
Link: https://lore.kernel.org/r/20220309213755.610202-1-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
