This patch adds support for half duplex operation at 10M and 100M link
speeds for AM654x/AM64x devices.
- Driver configures rand_seed, a random number, in DMEM HD_RAND_SEED_OFFSET
field, which will be used by firmware for Back off time calculation.
- Driver informs FW about half duplex link operation in DMEM
PORT_LINK_SPEED_OFFSET field by setting bit 7 for 10/100M HD.
Hence, the half duplex operation depends on board design the
"ti,half-duplex-capable" property has to be enabled for ICSS-G ports if HW
is capable to perform half duplex.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We auto-negotiate most ports in the RTL8366RB driver, but
the CPU port is hard-coded to 1Gbit, full duplex, tx and
rx pause.
This isn't very nice. People may configure speed and
duplex differently in the device tree.
Actually respect the arguments passed to the function for
the CPU port, which get passed properly after Russell's
patch "net: dsa: realtek: add phylink_get_caps implementation"
After this the link is still set up properly.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PTP block supports generating PPS output signal on GPIO pin. This patch
adds the support in the PTP PHC driver using standard periodic output
interface.
User can enable/disable/configure PPS by writing to the below sysfs entry
echo perout.index start.sec start.nsec period.sec period.nsec >
/sys/class/ptp/ptp0/period
Example to generate 50% duty cycle PPS signal:
echo 0 0 0 0 500000000 > /sys/class/ptp/ptp0/period
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com>
Signed-off-by: Sai Krishna <saikrishnag@marvell.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add spin lock protection for irq {un}mask registers' control.
After napi_complete_done() and this protection were applied,
a lot of redundant interrupts no longer occur.
For example: when "iperf3 -c <ipaddr> -R" on R-Car S4-8 Spider
Before the patches are applied: about 800,000 times happened
After the patches were applied: about 100,000 times happened
Fixes: 3590918b5d ("net: ethernet: renesas: Add support for "Ethernet Switch"")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
This is based on alx driver commit 881d0327db ("net: alx: Work around
the DMA RX overflow issue").
The alx and atl1c drivers had RX overflow error which was why a custom
allocator was created to avoid certain addresses. The simpler workaround
then created for alx driver, but not for atl1c due to lack of tester.
Instead of using a custom allocator, check the allocated skb address and
use skb_reserve() to move away from problematic 0x...fc0 address.
Tested on AR8131 on Acer 4540.
Signed-off-by: Sieng-Piaw Liew <liew.s.piaw@gmail.com>
Link: https://lore.kernel.org/r/20230912010711.12036-1-liew.s.piaw@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
After commit 50f303496d ("igb: Enable SR-IOV after reinit"), removing
the igb module could hang or crash (depending on the machine) when the
module has been loaded with the max_vfs parameter set to some value != 0.
In case of one test machine with a dual port 82580, this hang occurred:
[ 232.480687] igb 0000:41:00.1: removed PHC on enp65s0f1
[ 233.093257] igb 0000:41:00.1: IOV Disabled
[ 233.329969] pcieport 0000:40:01.0: AER: Multiple Uncorrected (Non-Fatal) err0
[ 233.340302] igb 0000:41:00.0: PCIe Bus Error: severity=Uncorrected (Non-Fata)
[ 233.352248] igb 0000:41:00.0: device [8086:1516] error status/mask=00100000
[ 233.361088] igb 0000:41:00.0: [20] UnsupReq (First)
[ 233.368183] igb 0000:41:00.0: AER: TLP Header: 40000001 0000040f cdbfc00c c
[ 233.376846] igb 0000:41:00.1: PCIe Bus Error: severity=Uncorrected (Non-Fata)
[ 233.388779] igb 0000:41:00.1: device [8086:1516] error status/mask=00100000
[ 233.397629] igb 0000:41:00.1: [20] UnsupReq (First)
[ 233.404736] igb 0000:41:00.1: AER: TLP Header: 40000001 0000040f cdbfc00c c
[ 233.538214] pci 0000:41:00.1: AER: can't recover (no error_detected callback)
[ 233.538401] igb 0000:41:00.0: removed PHC on enp65s0f0
[ 233.546197] pcieport 0000:40:01.0: AER: device recovery failed
[ 234.157244] igb 0000:41:00.0: IOV Disabled
[ 371.619705] INFO: task irq/35-aerdrv:257 blocked for more than 122 seconds.
[ 371.627489] Not tainted 6.4.0-dirty #2
[ 371.632257] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this.
[ 371.641000] task:irq/35-aerdrv state:D stack:0 pid:257 ppid:2 f0
[ 371.650330] Call Trace:
[ 371.653061] <TASK>
[ 371.655407] __schedule+0x20e/0x660
[ 371.659313] schedule+0x5a/0xd0
[ 371.662824] schedule_preempt_disabled+0x11/0x20
[ 371.667983] __mutex_lock.constprop.0+0x372/0x6c0
[ 371.673237] ? __pfx_aer_root_reset+0x10/0x10
[ 371.678105] report_error_detected+0x25/0x1c0
[ 371.682974] ? __pfx_report_normal_detected+0x10/0x10
[ 371.688618] pci_walk_bus+0x72/0x90
[ 371.692519] pcie_do_recovery+0xb2/0x330
[ 371.696899] aer_process_err_devices+0x117/0x170
[ 371.702055] aer_isr+0x1c0/0x1e0
[ 371.705661] ? __set_cpus_allowed_ptr+0x54/0xa0
[ 371.710723] ? __pfx_irq_thread_fn+0x10/0x10
[ 371.715496] irq_thread_fn+0x20/0x60
[ 371.719491] irq_thread+0xe6/0x1b0
[ 371.723291] ? __pfx_irq_thread_dtor+0x10/0x10
[ 371.728255] ? __pfx_irq_thread+0x10/0x10
[ 371.732731] kthread+0xe2/0x110
[ 371.736243] ? __pfx_kthread+0x10/0x10
[ 371.740430] ret_from_fork+0x2c/0x50
[ 371.744428] </TASK>
The reproducer was a simple script:
#!/bin/sh
for i in `seq 1 5`; do
modprobe -rv igb
modprobe -v igb max_vfs=1
sleep 1
modprobe -rv igb
done
It turned out that this could only be reproduce on 82580 (quad and
dual-port), but not on 82576, i350 and i210. Further debugging showed
that igb_enable_sriov()'s call to pci_enable_sriov() is failing, because
dev->is_physfn is 0 on 82580.
Prior to commit 50f303496d ("igb: Enable SR-IOV after reinit"),
igb_enable_sriov() jumped into the "err_out" cleanup branch. After this
commit it only returned the error code.
So the cleanup didn't take place, and the incorrect VF setup in the
igb_adapter structure fooled the igb driver into assuming that VFs have
been set up where no VF actually existed.
Fix this problem by cleaning up again if pci_enable_sriov() fails.
Fixes: 50f303496d ("igb: Enable SR-IOV after reinit")
Signed-off-by: Corinna Vinschen <vinschen@redhat.com>
Reviewed-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit in fixes introduced flags to control the status of hardware
configuration while processing packets. At the same time another structure
is used to provide configuration of timestamper to user-space applications.
The way it was coded makes this structures go out of sync easily. The
repro is easy for 82599 chips:
[root@hostname ~]# hwstamp_ctl -i eth0 -r 12 -t 1
current settings:
tx_type 0
rx_filter 0
new settings:
tx_type 1
rx_filter 12
The eth0 device is properly configured to timestamp any PTPv2 events.
[root@hostname ~]# hwstamp_ctl -i eth0 -r 1 -t 1
current settings:
tx_type 1
rx_filter 12
SIOCSHWTSTAMP failed: Numerical result out of range
The requested time stamping mode is not supported by the hardware.
The error is properly returned because HW doesn't support all packets
timestamping. But the adapter->flags is cleared of timestamp flags
even though no HW configuration was done. From that point no RX timestamps
are received by user-space application. But configuration shows good
values:
[root@hostname ~]# hwstamp_ctl -i eth0
current settings:
tx_type 1
rx_filter 12
Fix the issue by applying new flags only when the HW was actually
configured.
Fixes: a9763f3cb5 ("ixgbe: Update PTP to support X550EM_x devices")
Signed-off-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2023-09-11 (i40e, iavf)
This series contains updates to i40e and iavf drivers.
Andrii ensures all VSIs are cleaned up for remove in i40e.
Brett reworks logic for setting promiscuous mode that can, currently, cause
incorrect states on iavf.
---
v2:
- Remove redundant i40e_vsi_free_q_vectors() and kfree() calls (patch 1)
v1: https://lore.kernel.org/netdev/20230905180521.887861-1-anthony.l.nguyen@intel.com/
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
There's an early return in veth_set_features() if the device is in a down
state, which leads to the XDP feature flags not being updated when enabling
GRO while the device is down. Which in turn leads to XDP_REDIRECT not
working, because the redirect code now checks the flags.
Fix this by updating the feature flags after bringing the device up.
Before this patch:
NETDEV_XDP_ACT_BASIC: yes
NETDEV_XDP_ACT_REDIRECT: yes
NETDEV_XDP_ACT_NDO_XMIT: no
NETDEV_XDP_ACT_XSK_ZEROCOPY: no
NETDEV_XDP_ACT_HW_OFFLOAD: no
NETDEV_XDP_ACT_RX_SG: yes
NETDEV_XDP_ACT_NDO_XMIT_SG: no
After this patch:
NETDEV_XDP_ACT_BASIC: yes
NETDEV_XDP_ACT_REDIRECT: yes
NETDEV_XDP_ACT_NDO_XMIT: yes
NETDEV_XDP_ACT_XSK_ZEROCOPY: no
NETDEV_XDP_ACT_HW_OFFLOAD: no
NETDEV_XDP_ACT_RX_SG: yes
NETDEV_XDP_ACT_NDO_XMIT_SG: yes
Fixes: fccca038f3 ("veth: take into account device reconfiguration for xdp_features flag")
Fixes: 66c0e13ad2 ("drivers: net: turn on XDP features")
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Link: https://lore.kernel.org/r/20230911135826.722295-1-toke@redhat.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
macb_set_tx_clk() is called under a spinlock but itself calls clk_set_rate()
which can sleep. This results in:
| BUG: sleeping function called from invalid context at kernel/locking/mutex.c:580
| pps pps1: new PPS source ptp1
| in_atomic(): 1, irqs_disabled(): 1, non_block: 0, pid: 40, name: kworker/u4:3
| preempt_count: 1, expected: 0
| RCU nest depth: 0, expected: 0
| 4 locks held by kworker/u4:3/40:
| #0: ffff000003409148
| macb ff0c0000.ethernet: gem-ptp-timer ptp clock registered.
| ((wq_completion)events_power_efficient){+.+.}-{0:0}, at: process_one_work+0x14c/0x51c
| #1: ffff8000833cbdd8 ((work_completion)(&pl->resolve)){+.+.}-{0:0}, at: process_one_work+0x14c/0x51c
| #2: ffff000004f01578 (&pl->state_mutex){+.+.}-{4:4}, at: phylink_resolve+0x44/0x4e8
| #3: ffff000004f06f50 (&bp->lock){....}-{3:3}, at: macb_mac_link_up+0x40/0x2ac
| irq event stamp: 113998
| hardirqs last enabled at (113997): [<ffff800080e8503c>] _raw_spin_unlock_irq+0x30/0x64
| hardirqs last disabled at (113998): [<ffff800080e84478>] _raw_spin_lock_irqsave+0xac/0xc8
| softirqs last enabled at (113608): [<ffff800080010630>] __do_softirq+0x430/0x4e4
| softirqs last disabled at (113597): [<ffff80008001614c>] ____do_softirq+0x10/0x1c
| CPU: 0 PID: 40 Comm: kworker/u4:3 Not tainted 6.5.0-11717-g9355ce8b2f50-dirty #368
| Hardware name: ... ZynqMP ... (DT)
| Workqueue: events_power_efficient phylink_resolve
| Call trace:
| dump_backtrace+0x98/0xf0
| show_stack+0x18/0x24
| dump_stack_lvl+0x60/0xac
| dump_stack+0x18/0x24
| __might_resched+0x144/0x24c
| __might_sleep+0x48/0x98
| __mutex_lock+0x58/0x7b0
| mutex_lock_nested+0x24/0x30
| clk_prepare_lock+0x4c/0xa8
| clk_set_rate+0x24/0x8c
| macb_mac_link_up+0x25c/0x2ac
| phylink_resolve+0x178/0x4e8
| process_one_work+0x1ec/0x51c
| worker_thread+0x1ec/0x3e4
| kthread+0x120/0x124
| ret_from_fork+0x10/0x20
The obvious fix is to move the call to macb_set_tx_clk() out of the
protected area. This seems safe as rx and tx are both disabled anyway at
this point.
It is however not entirely clear what the spinlock shall protect. It
could be the read-modify-write access to the NCFGR register, but this
is accessed in macb_set_rx_mode() and macb_set_rxcsum_feature() as well
without holding the spinlock. It could also be the register accesses
done in mog_init_rings() or macb_init_buffers(), but again these
functions are called without holding the spinlock in macb_hresp_error_task().
The locking seems fishy in this driver and it might deserve another look
before this patch is applied.
Fixes: 633e98a711 ("net: macb: use resolved link config in mac_link_up()")
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Link: https://lore.kernel.org/r/20230908112913.1701766-1-s.hauer@pengutronix.de
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Add AM64x ICSSG support which is similar to am65x SR2.0, but required:
- all ring configured in exposed ring mode
- always fill both original and buffer fields in cppi5 desc
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Currently when configuring promiscuous mode on the AVF we detect a
change in the netdev->flags. We use IFF_PROMISC and IFF_ALLMULTI to
determine whether or not we need to request/release promiscuous mode
and/or multicast promiscuous mode. The problem is that the AQ calls for
setting/clearing promiscuous/multicast mode are treated separately. This
leads to a case where we can trigger two promiscuous mode AQ calls in
a row with the incorrect state. To fix this make a few changes.
Use IAVF_FLAG_AQ_CONFIGURE_PROMISC_MODE instead of the previous
IAVF_FLAG_AQ_[REQUEST|RELEASE]_[PROMISC|ALLMULTI] flags.
In iavf_set_rx_mode() detect if there is a change in the
netdev->flags in comparison with adapter->flags and set the
IAVF_FLAG_AQ_CONFIGURE_PROMISC_MODE aq_required bit. Then in
iavf_process_aq_command() only check for IAVF_FLAG_CONFIGURE_PROMISC_MODE
and call iavf_set_promiscuous() if it's set.
In iavf_set_promiscuous() check again to see which (if any) promiscuous
mode bits have changed when comparing the netdev->flags with the
adapter->flags. Use this to set the flags which get sent to the PF
driver.
Add a spinlock that is used for updating current_netdev_promisc_flags
and only allows one promiscuous mode AQ at a time.
[1] Fixes the fact that we will only have one AQ call in the aq_required
queue at any one time.
[2] Streamlines the change in promiscuous mode to only set one AQ
required bit.
[3] This allows us to keep track of the current state of the flags and
also makes it so we can take the most recent netdev->flags promiscuous
mode state.
[4] This fixes the problem where a change in the netdev->flags can cause
IAVF_FLAG_AQ_CONFIGURE_PROMISC_MODE to be set in iavf_set_rx_mode(),
but cleared in iavf_set_promiscuous() before the change is ever made via
AQ call.
Fixes: 47d3483988 ("i40evf: Add driver support for promiscuous mode")
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Ahmed Zaki <ahmed.zaki@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Instead of freeing memory of a single VSI, make sure
the memory for all VSIs is cleared before releasing VSIs.
Add releasing of their resources in a loop with the iteration
number equal to the number of allocated VSIs.
Fixes: 41c445ff0f ("i40e: main driver core")
Signed-off-by: Andrii Staikov <andrii.staikov@intel.com>
Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
MT7988 SoC support 3 NICs. Fix pse_port configuration in
mtk_flow_set_output_device routine if the traffic is offloaded to eth2.
Rely on mtk_pse_port definitions.
Fixes: 88efedf517 ("net: ethernet: mtk_eth_soc: enable nft hw flowtable_offload for MT7988 SoC")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Variable dma_addr in function mtk_poll_rx can be uninitialized on
some of the error paths. In practise this doesn't matter, even random
data present in uninitialized stack memory can safely be used in the
way it happens in the error path.
However, in order to make Smatch happy make sure the variable is
always initialized.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to the document of napi, there is no rx process when the
budget is 0. Therefore, r8152_poll() has to return 0 directly when the
budget is equal to 0.
Fixes: d2187f8e44 ("r8152: divide the tx and rx bottom functions")
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, when we add the first sja1105 port to a bridge with
vlan_filtering 1, then we sometimes see this output:
sja1105 spi2.2: port 4 failed to read back entry for be:79:b4:9e:9e:96 vid 3088: -ENOENT
sja1105 spi2.2: Reset switch and programmed static config. Reason: VLAN filtering
sja1105 spi2.2: port 0 failed to add be:79:b4:9e:9e:96 vid 0 to fdb: -2
It is because sja1105_fdb_add() runs from the dsa_owq which is no longer
serialized with switch resets since it dropped the rtnl_lock() in the
blamed commit.
Either performing the FDB accesses before the reset, or after the reset,
is equally fine, because sja1105_static_fdb_change() backs up those
changes in the static config, but FDB access during reset isn't ok.
Make sja1105_static_config_reload() take the fdb_lock to fix that.
Fixes: 0faf890fc5 ("net: dsa: drop rtnl_lock from dsa_slave_switchdev_event_work")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sja1105_fdb_add() runs from the dsa_owq, and sja1105_port_mcast_flood()
runs from switchdev_deferred_process_work(). Prior to the blamed commit,
they used to be indirectly serialized through the rtnl_lock(), which
no longer holds true because dsa_owq dropped that.
So, it is now possible that we traverse the static config BLK_IDX_L2_LOOKUP
elements concurrently compared to when we change them, in
sja1105_static_fdb_change(). That is not ideal, since it might result in
data corruption.
Introduce a mutex which serializes accesses to the hardware FDB and to
the static config elements for the L2 Address Lookup table.
I can't find a good reason to add locking around sja1105_fdb_dump().
I'll add it later if needed.
Fixes: 0faf890fc5 ("net: dsa: drop rtnl_lock from dsa_slave_switchdev_event_work")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit cited in Fixes: did 2 things: it refactored the read-back
polling from sja1105_dynamic_config_read() into a new function,
sja1105_dynamic_config_wait_complete(), and it called that from
sja1105_dynamic_config_write() too.
What is problematic is the refactoring.
The refactored code from sja1105_dynamic_config_poll_valid() works like
the previous one, but the problem is that it uses another packed_buf[]
SPI buffer, and there was code at the end of sja1105_dynamic_config_read()
which was relying on the read-back packed_buf[]:
/* Don't dereference possibly NULL pointer - maybe caller
* only wanted to see whether the entry existed or not.
*/
if (entry)
ops->entry_packing(packed_buf, entry, UNPACK);
After the change, the packed_buf[] that this code sees is no longer the
entry read back from hardware, but the original entry that the caller
passed to the sja1105_dynamic_config_read(), packed into this buffer.
This difference is the most notable with the SJA1105_SEARCH uses from
sja1105pqrs_fdb_add() - used for both fdb and mdb. There, we have logic
added by commit 728db843df ("net: dsa: sja1105: ignore the FDB entry
for unknown multicast when adding a new address") to figure out whether
the address we're trying to add matches on any existing hardware entry,
with the exception of the catch-all multicast address.
That logic was broken, because with sja1105_dynamic_config_read() not
working properly, it doesn't return us the entry read back from
hardware, but the entry that we passed to it. And, since for multicast,
a match will always exist, it will tell us that any mdb entry already
exists at index=0 L2 Address Lookup table. It is index=0 because the
caller doesn't know the index - it wants to find it out, and
sja1105_dynamic_config_read() does:
if (index < 0) { // SJA1105_SEARCH
/* Avoid copying a signed negative number to an u64 */
cmd.index = 0; // <- this
cmd.search = true;
} else {
cmd.index = index;
cmd.search = false;
}
So, to the caller of sja1105_dynamic_config_read(), the returned info
looks entirely legit, and it will add all mdb entries to FDB index 0.
There, they will always overwrite each other (not to mention,
potentially they can also overwrite a pre-existing bridge fdb entry),
and the user-visible impact will be that only the last mdb entry will be
forwarded as it should. The others won't (will be flooded or dropped,
depending on the egress flood settings).
Fixing is a bit more complicated, and involves either passing the same
packed_buf[] to sja1105_dynamic_config_wait_complete(), or moving all
the extra processing on the packed_buf[] to
sja1105_dynamic_config_wait_complete(). I've opted for the latter,
because it makes sja1105_dynamic_config_wait_complete() a bit more
self-contained.
Fixes: df405910ab ("net: dsa: sja1105: wait for dynamic config command completion on writes too")
Reported-by: Yanan Yang <yanan.yang@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, sja1105_dynamic_config_wait_complete() returns either 0 or
-ETIMEDOUT, because it just looks at the read_poll_timeout() return code.
There will be future changes which move some more checks to
sja1105_dynamic_config_poll_valid(). It is important that we propagate
their exact return code (-ENOENT, -EINVAL), because callers of
sja1105_dynamic_config_read() depend on them.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 4d94235495 ("net: dsa: sja1105: offload bridge port flags to
device") has partially hidden some multicast entries from showing up in
the "bridge fdb show" output, but it wasn't enough. Addresses which are
added through "bridge mdb add" still show up. Hide them all.
Fixes: 291d1e72b7 ("net: dsa: sja1105: Add support for FDB and MDB management")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, when a new fdb entry is added (with both ports of the
ADIN2111 bridged), the driver configures the MAC filters for the wrong
port, which results in the forwarding being done by the host, and not
actually hardware offloaded.
The ADIN2111 offloads the forwarding by setting filters on the
destination MAC address of incoming frames. Based on these, they may be
routed to the other port. Thus, if a frame has to be forwarded from port
1 to port 2, the required configuration for the ADDR_FILT_UPRn register
should set the APPLY2PORT1 bit (instead of APPLY2PORT2, as it's
currently the case).
Fixes: bc93e19d08 ("net: ethernet: adi: Add ADIN1110 support")
Signed-off-by: Ciprian Regus <ciprian.regus@analog.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
rule_locs is allocated in ethtool_get_rxnfc and the size is determined by
rule_cnt from user space. So rule_cnt needs to be check before using
rule_locs to avoid NULL pointer dereference.
Fixes: 7aab747e55 ("net: ethernet: mediatek: add ethtool functions to configure RX flows of HW LRO")
Signed-off-by: Hangyu Hua <hbh25y@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
rules is allocated in ethtool_get_rxnfc and the size is determined by
rule_cnt from user space. So rule_cnt needs to be check before using
rules to avoid OOB writing or NULL pointer dereference.
Fixes: 90b509b39a ("net: mvpp2: cls: Add Classification offload support")
Signed-off-by: Hangyu Hua <hbh25y@gmail.com>
Reviewed-by: Marcin Wojtas <mw@semihalf.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
rule_locs is allocated in ethtool_get_rxnfc and the size is determined by
rule_cnt from user space. So rule_cnt needs to be check before using
rule_locs to avoid OOB writing or NULL pointer dereference.
Fixes: c5d511c495 ("net: bcmasp: Add support for wake on net filters")
Signed-off-by: Hangyu Hua <hbh25y@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Setting ethtool -C eth0 tx-usecs 0 is supposed to disable the use of the
coalescing timer but currently it gets programmed with zero delay
instead.
Disable the use of the coalescing timer if tx-usecs is zero by
preventing it from being restarted. Note that to keep things simple we
don't start/stop the timer when the coalescing settings are changed, but
just let that happen on the next transmit or timer expiry.
Fixes: 8fce333170 ("net: stmmac: Rework coalesce timer and fix multi-queue races")
Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The access to page pool `cache' array and the `count' variable
is not locked. Page pool cache access is fine as long as there
is only one consumer per pool.
octeontx2 driver fills in rx buffers from page pool in NAPI context.
If system is stressed and could not allocate buffers, refiiling work
will be delegated to a delayed workqueue. This means that there are
two cosumers to the page pool cache.
Either workqueue or IRQ/NAPI can be run on other CPU. This will lead
to lock less access, hence corruption of cache pool indexes.
To fix this issue, NAPI is rescheduled from workqueue context to refill
rx buffers.
Fixes: b2e3406a38 ("octeontx2-pf: Add support for page pool")
Signed-off-by: Ratheesh Kannoth <rkannoth@marvell.com>
Reported-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
for_each_available_child_of_node performs an of_node_get
on each iteration, so a break out of the loop requires an
of_node_put.
This was done using the Coccinelle semantic patch
iterators/for_each_child.cocci
Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking updates from Jakub Kicinski:
"Including fixes from netfilter and bpf.
Current release - regressions:
- eth: stmmac: fix failure to probe without MAC interface specified
Current release - new code bugs:
- docs: netlink: fix missing classic_netlink doc reference
Previous releases - regressions:
- deal with integer overflows in kmalloc_reserve()
- use sk_forward_alloc_get() in sk_get_meminfo()
- bpf_sk_storage: fix the missing uncharge in sk_omem_alloc
- fib: avoid warn splat in flow dissector after packet mangling
- skb_segment: call zero copy functions before using skbuff frags
- eth: sfc: check for zero length in EF10 RX prefix
Previous releases - always broken:
- af_unix: fix msg_controllen test in scm_pidfd_recv() for
MSG_CMSG_COMPAT
- xsk: fix xsk_build_skb() dereferencing possible ERR_PTR()
- netfilter:
- nft_exthdr: fix non-linear header modification
- xt_u32, xt_sctp: validate user space input
- nftables: exthdr: fix 4-byte stack OOB write
- nfnetlink_osf: avoid OOB read
- one more fix for the garbage collection work from last release
- igmp: limit igmpv3_newpack() packet size to IP_MAX_MTU
- bpf, sockmap: fix preempt_rt splat when using raw_spin_lock_t
- handshake: fix null-deref in handshake_nl_done_doit()
- ip: ignore dst hint for multipath routes to ensure packets are
hashed across the nexthops
- phy: micrel:
- correct bit assignments for cable test errata
- disable EEE according to the KSZ9477 errata
Misc:
- docs/bpf: document compile-once-run-everywhere (CO-RE) relocations
- Revert "net: macsec: preserve ingress frame ordering", it appears
to have been developed against an older kernel, problem doesn't
exist upstream"
* tag 'net-6.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (95 commits)
net: enetc: distinguish error from valid pointers in enetc_fixup_clear_rss_rfs()
Revert "net: team: do not use dynamic lockdep key"
net: hns3: remove GSO partial feature bit
net: hns3: fix the port information display when sfp is absent
net: hns3: fix invalid mutex between tc qdisc and dcb ets command issue
net: hns3: fix debugfs concurrency issue between kfree buffer and read
net: hns3: fix byte order conversion issue in hclge_dbg_fd_tcam_read()
net: hns3: Support query tx timeout threshold by debugfs
net: hns3: fix tx timeout issue
net: phy: Provide Module 4 KSZ9477 errata (DS80000754C)
netfilter: nf_tables: Unbreak audit log reset
netfilter: ipset: add the missing IP_SET_HASH_WITH_NET0 macro for ip_set_hash_netportnet.c
netfilter: nft_set_rbtree: skip sync GC for new elements in this transaction
netfilter: nf_tables: uapi: Describe NFTA_RULE_CHAIN_ID
netfilter: nfnetlink_osf: avoid OOB read
netfilter: nftables: exthdr: fix 4-byte stack OOB write
selftests/bpf: Check bpf_sk_storage has uncharged sk_omem_alloc
bpf: bpf_sk_storage: Fix the missing uncharge in sk_omem_alloc
bpf: bpf_sk_storage: Fix invalid wait context lockdep report
s390/bpf: Pass through tail call counter in trampolines
...
HNS3 NIC does not support GSO partial packets segmentation. Actually tunnel
packets for example NvGRE packets segment offload and checksum offload is
already supported. There is no need to keep gso partial feature bit. So
this patch removes it.
Fixes: 76ad4f0ee7 ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
When sfp is absent or unidentified, the port type should be
displayed as PORT_OTHERS, rather than PORT_FIBRE.
Fixes: 88d10bd6f7 ("net: hns3: add support for multiple media type")
Signed-off-by: Yisen Zhuang <yisen.zhuang@huawei.com>
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
We hope that tc qdisc and dcb ets commands can not be used crosswise.
If we want to use any of the commands to configure tc,
We must use the other command to clear the existing configuration.
However, when we configure a single tc with tc qdisc,
we can still configure it with dcb ets.
Because we use mqprio_active as the tag of tc qdisc configuration,
but with dcb ets, we do not check mqprio_active.
This patch fix this issue by check mqprio_active before
executing the dcb ets command. and add dcb_ets_active to
replace HCLGE_FLAG_DCB_ENABLE and HCLGE_FLAG_MQPRIO_ENABLE
at the hclge layer,
Fixes: cacde272dd ("net: hns3: Add hclge_dcb module for the support of DCB feature")
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Now in hns3_dbg_uninit(), there may be concurrency between
kfree buffer and read, it may result in memory error.
Moving debugfs_remove_recursive() in front of kfree buffer to ensure
they don't happen at the same time.
Fixes: 5e69ea7ee2 ("net: hns3: refactor the debugfs process")
Signed-off-by: Hao Chen <chenhao418@huawei.com>
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
req1->tcam_data is defined as "u8 tcam_data[8]", and we convert it as
(u32 *) without considerring byte order conversion,
it may result in printing wrong data for tcam_data.
Convert tcam_data to (__le32 *) first to fix it.
Fixes: b5a0b70d77 ("net: hns3: refactor dump fd tcam of debugfs")
Signed-off-by: Hao Chen <chenhao418@huawei.com>
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Currently, the driver knocks the ring doorbell before updating
the ring->last_to_use in tx flow. if the hardware transmiting
packet and napi poll scheduling are fast enough, it may get
the old ring->last_to_use in drivers' napi poll.
In this case, the driver will think the tx is not completed, and
return directly without clear the flag __QUEUE_STATE_STACK_XOFF,
which may cause tx timeout.
Fixes: 20d06ca267 ("net: hns3: optimize the tx clean process")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The KSZ9477 errata points out (in 'Module 4') the link up/down problems
when EEE (Energy Efficient Ethernet) is enabled in the device to which
the KSZ9477 tries to auto negotiate.
The suggested workaround is to clear advertisement of EEE for PHYs in
this chip driver.
To avoid regressions with other switch ICs the new MICREL_NO_EEE flag
has been introduced.
Moreover, the in-register disablement of MMD_DEVICE_ID_EEE_ADV.MMD_EEE_ADV
MMD register is removed, as this code is both; now executed too late
(after previous rework of the PHY and DSA for KSZ switches) and not
required as setting all members of eee_broken_modes bit field prevents
the KSZ9477 from advertising EEE.
Fixes: 69d3b36ca0 ("net: dsa: microchip: enable EEE support") # for KSZ9477
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Tested-by: Oleksij Rempel <o.rempel@pengutronix.de> # Confirmed disabled EEE with oscilloscope.
Reviewed-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20230905093315.784052-1-lukma@denx.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The blamed commit left this delta behind:
struct sja1105_cbs_entry {
- u64 port;
- u64 prio;
+ u64 port; /* Not used for SJA1110 */
+ u64 prio; /* Not used for SJA1110 */
u64 credit_hi;
u64 credit_lo;
u64 send_slope;
u64 idle_slope;
};
but did not actually implement tc-cbs offload fully for the new switch.
The offload is accepted, but it doesn't work.
The difference compared to earlier switch generations is that now, the
table of CBS shapers is sparse, because there are many more shapers, so
the mapping between a {port, prio} and a table index is static, rather
than requiring us to store the port and prio into the sja1105_cbs_entry.
So, the problem is that the code programs the CBS shaper parameters at a
dynamic table index which is incorrect.
All that needs to be done for SJA1110 CBS shapers to work is to bypass
the logic which allocates shapers in a dense manner, as for SJA1105, and
use the fixed mapping instead.
Fixes: 3e77e59bf8 ("net: dsa: sja1105: add support for the SJA1110 switch family")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After running command [2] too many times in a row:
[1] $ tc qdisc add dev sw2p0 root handle 1: mqprio num_tc 8 \
map 0 1 2 3 4 5 6 7 queues 1@0 1@1 1@2 1@3 1@4 1@5 1@6 1@7 hw 0
[2] $ tc qdisc replace dev sw2p0 parent 1:1 cbs offload 1 \
idleslope 120000 sendslope -880000 locredit -1320 hicredit 180
(aka more than priv->info->num_cbs_shapers times)
we start seeing the following error message:
Error: Specified device failed to setup cbs hardware offload.
This comes from the fact that ndo_setup_tc(TC_SETUP_QDISC_CBS) presents
the same API for the qdisc create and replace cases, and the sja1105
driver fails to distinguish between the 2. Thus, it always thinks that
it must allocate the same shaper for a {port, queue} pair, when it may
instead have to replace an existing one.
Fixes: 4d7525085a ("net: dsa: sja1105: offload the Credit-Based Shaper qdisc")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
