Pull more ARM multiplatform updates from Arnd Bergmann:
"The second part of the multiplatform changes now converts the
Intel/Marvell PXA platform along with the rest. The patches went
through several rebases before the merge window as bugs were found, so
they remained separate.
This has to touch a lot of drivers, in particular the touchscreen,
pcmcia, sound and clk bits, to detach the driver files from the
platform and board specific header files"
* tag 'arm-multiplatform-5.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (48 commits)
ARM: pxa/mmp: remove traces of plat-pxa
ARM: pxa: convert to multiplatform
ARM: pxa/sa1100: move I/O space to PCI_IOBASE
ARM: pxa: remove support for MTD_XIP
ARM: pxa: move mach/*.h to mach-pxa/
ARM: PXA: fix multi-cpu build of xsc3
ARM: pxa: move plat-pxa to drivers/soc/
ARM: mmp: rename pxa_register_device
ARM: mmp: remove tavorevb board support
ARM: pxa: remove unused mach/bitfield.h
ARM: pxa: move clk register definitions to driver
ARM: pxa: move smemc register access from clk to platform
cpufreq: pxa3: move clk register access to clk driver
ARM: pxa: remove get_clk_frequency_khz()
ARM: pxa: pcmcia: move smemc configuration back to arch
ASoC: pxa: i2s: use normal MMIO accessors
ASoC: pxa: ac97: use normal MMIO accessors
ASoC: pxa: use pdev resource for FIFO regs
Input: wm97xx - get rid of irq_enable method in wm97xx_mach_ops
Input: wm97xx - switch to using threaded IRQ
...
Pull dmaengine updates from Vinod Koul:
"Nothing special, this includes a couple of new device support and new
driver support and bunch of driver updates.
New support:
- Tegra gpcdma driver support
- Qualcomm SM8350, Sm8450 and SC7280 device support
- Renesas RZN1 dma and platform support
Updates:
- stm32 device pause/resume support and updates
- DMA memset ops Documentation and usage clarification
- deprecate '#dma-channels' & '#dma-requests' bindings
- driver updates for stm32, ptdma idsx etc"
* tag 'dmaengine-5.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/dmaengine: (87 commits)
dmaengine: idxd: make idxd_wq_enable() return 0 if wq is already enabled
dmaengine: sun6i: Add support for the D1 variant
dmaengine: sun6i: Add support for 34-bit physical addresses
dmaengine: sun6i: Do not use virt_to_phys
dt-bindings: dma: sun50i-a64: Add compatible for D1
dmaengine: tegra: Remove unused switch case
dmaengine: tegra: Fix uninitialized variable usage
dmaengine: stm32-dma: add device_pause/device_resume support
dmaengine: stm32-dma: rename pm ops before dma pause/resume introduction
dmaengine: stm32-dma: pass DMA_SxSCR value to stm32_dma_handle_chan_done()
dmaengine: stm32-dma: introduce stm32_dma_sg_inc to manage chan->next_sg
dmaengine: stm32-dmamux: avoid reset of dmamux if used by coprocessor
dmaengine: qcom: gpi: Add support for sc7280
dt-bindings: dma: pl330: Add power-domains
dmaengine: stm32-mdma: use dev_dbg on non-busy channel spurious it
dmaengine: stm32-mdma: fix chan initialization in stm32_mdma_irq_handler()
dmaengine: stm32-mdma: remove GISR1 register
dmaengine: ti: deprecate '#dma-channels'
dmaengine: mmp: deprecate '#dma-channels'
dmaengine: pxa: deprecate '#dma-channels' and '#dma-requests'
...
Pull ARMv4T/v5 multiplatform support from Arnd Bergmann:
"This series has been 12 years in the making, it mostly finishes the
work that was started with the founding of Linaro to clean up platform
support in the kernel.
The largest change here is a cleanup of the omap1 platform, which is
the final ARM machine type to get converted to the common-clk
subsystem. All the omap1 specific drivers are now made independent of
the mach/*.h headers to allow the platform to be part of a generic
ARMv4/v5 multiplatform kernel.
The last bit that enables this support is still missing here while we
wait for some last dependencies to make it into the mainline kernel
through other subsystems.
The s3c24xx, ixp4xx, iop32x, ep93xx and dove platforms were all almost
at the point of allowing multiplatform kernels, this work gets
completed here along with a few additional cleanup. At the same time,
the s3c24xx and s3c64xx are now deprecated and expected to get removed
in the future.
The PXA and OMAP1 bits are in a separate branch because of
dependencies. Once both branches are merged, only the three Intel
StrongARM platforms (RiscPC, Footbridge/NetWinder and StrongARM1100)
need separate kernels, and there are no plans to include these"
* tag 'arm-multiplatform-5.19-1' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (61 commits)
ARM: ixp4xx: Consolidate Kconfig fixing issue
ARM: versatile: Add missing of_node_put in dcscb_init
ARM: config: Refresh IXP4xx config after multiplatform
ARM: omap1: add back omap_set_dma_priority() stub
ARM: omap: fix missing declaration warnings
ARM: omap: fix address space warnings from sparse
ARM: spear: remove include/mach/ subdirectory
ARM: davinci: remove include/mach/ subdirectory
ARM: omap2: remove include/mach/ subdirectory
integrator: remove empty ap_init_early()
ARM: s3c: fix include path
MAINTAINERS: omap1: Add Janusz as an additional maintainer
ARM: omap1: htc_herald: fix typos in comments
ARM: OMAP1: fix typos in comments
ARM: OMAP1: clock: Remove noop code
ARM: OMAP1: clock: Remove unused code
ARM: OMAP1: clock: Fix UART rate reporting algorithm
ARM: OMAP1: clock: Fix early UART rate issues
ARM: OMAP1: Prepare for conversion of OMAP1 clocks to CCF
ARM: omap1: fix build with no SoC selected
...
Pull ARM driver updates from Arnd Bergmann:
"There are minor updates to SoC specific drivers for chips by Rockchip,
Samsung, NVIDIA, TI, NXP, i.MX, Qualcomm, and Broadcom.
Noteworthy driver changes include:
- Several conversions of DT bindings to yaml format.
- Renesas adds driver support for R-Car V4H, RZ/V2M and RZ/G2UL SoCs.
- Qualcomm adds a bus driver for the SSC (Snapdragon Sensor Core),
and support for more chips in the RPMh power domains and the
soc-id.
- NXP has a new driver for the HDMI blk-ctrl on i.MX8MP.
- Apple M1 gains support for the on-chip NVMe controller, making it
possible to finally use the internal disks. This also includes SoC
drivers for their RTKit IPC and for the SART DMA address filter.
For other subsystems that merge their drivers through the SoC tree, we
have
- Firmware drivers for the ARM firmware stack including TEE, OP-TEE,
SCMI and FF-A get a number of smaller updates and cleanups. OP-TEE
now has a cache for firmware argument structures as an
optimization, and SCMI now supports the 3.1 version of the
specification.
- Reset controller updates to Amlogic, ASpeed, Renesas and ACPI
drivers
- Memory controller updates for Tegra, and a few updates for other
platforms"
* tag 'arm-drivers-5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (159 commits)
memory: tegra: Add MC error logging on Tegra186 onward
memory: tegra: Add memory controller channels support
memory: tegra: Add APE memory clients for Tegra234
memory: tegra: Add Tegra234 support
nvme-apple: fix sparse endianess warnings
soc/tegra: pmc: Document core domain fields
soc: qcom: pdr: use static for servreg_* variables
soc: imx: fix semicolon.cocci warnings
soc: renesas: R-Car V3U is R-Car Gen4
soc: imx: add i.MX8MP HDMI blk-ctrl
soc: imx: imx8m-blk-ctrl: Add i.MX8MP media blk-ctrl
soc: imx: add i.MX8MP HSIO blk-ctrl
soc: imx: imx8m-blk-ctrl: set power device name
soc: qcom: llcc: Add sc8180x and sc8280xp configurations
dt-bindings: arm: msm: Add sc8180x and sc8280xp LLCC compatibles
soc/tegra: pmc: Select REGMAP
dt-bindings: reset: st,sti-powerdown: Convert to yaml
dt-bindings: reset: st,sti-picophyreset: Convert to yaml
dt-bindings: reset: socfpga: Convert to yaml
dt-bindings: reset: snps,axs10x-reset: Convert to yaml
...
Pull 32-bit ARM SoC updates from Arnd Bergmann:
"These updates are for platform specific code in arch/arm/, mostly
fixing minor issues.
The at91 platform gains support for better power management on the
lan966 platform and new firmware on the sama5 platform. The mediatek
soc drivers in turn are enabled for the new mt8195 SoC"
* tag 'arm-soc-5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (34 commits)
ARM: at91: debug: add lan966 support
ARM: at91: pm: add support for sama5d2 secure suspend
ARM: at91: add code to handle secure calls
ARM: at91: Kconfig: implement PIT64B selection
ARM: at91: pm: add quirks for pm
ARM: at91: pm: use kernel documentation style
ARM: at91: pm: introduce macros for pm mode replacement
ARM: at91: pm: keep documentation inline with structure members
orion5x: fix typos in comments
ARM: hisi: Add missing of_node_put after of_find_compatible_node
ARM: shmobile: rcar-gen2: Drop comma after OF match table sentinel
ARM: shmobile: Drop commas after dt_compat sentinels
soc: mediatek: mutex: remove mt8195 MOD0 and SOF0 definition
MAINTAINERS: Add Broadcom BCMBCA entry
arm: bcmbca: add arch bcmbca machine entry
MAINTAINERS: Broadcom internal lists aren't maintainers
dt-bindings: pwrap: mediatek: Update pwrap document for mt8195
soc: mediatek: add DDP_DOMPONENT_DITHER0 enum for mt8195 vdosys0
soc: mediatek: add mtk-mutex support for mt8195 vdosys0
soc: mediatek: add mtk-mmsys support for mt8195 vdosys0
...
Qualcomm driver updates for v5.19
This converts a wide range of Qualcomm-related DeviceTree bindings to
YAML, in order to improve our ability to validate the DeviceTree source.
The RPMh power-domain driver gains support for the modem platform SDX65,
the compute platform SC8280XP and the automotive platform SA8540p. While
LLCC gains support for SC8180X and SC8280XP and gains a
MODULE_DEVICE_TABLE() to make it functional as a module.
It adds a driver for configuring the SSC bus, providing Linux access to
the hardware blocks in the sensor subsystem.
The socinfo driver gets confusion related to MSM8974 Pro sorted out and
adds new ids for SM8540 and SC7280.
The SCM driver gains support for MSM8974.
Add missing of_node_put() in smp2p and smsm drivers.
Stop using iterator after list_for_each_entry() and define static
definitions as such, in the PDR driver.
* tag 'qcom-drivers-for-5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux: (33 commits)
soc: qcom: pdr: use static for servreg_* variables
soc: qcom: llcc: Add sc8180x and sc8280xp configurations
dt-bindings: arm: msm: Add sc8180x and sc8280xp LLCC compatibles
soc: qcom: rpmhpd: add sc8280xp & sa8540p rpmh power-domains
soc: qcom: rpmhpd: Don't warn about sparse rpmhpd arrays
dt-bindings: power: rpmpd: Add sc8280xp RPMh power-domains
spi: dt-bindings: qcom,spi-geni-qcom: convert to dtschema
soc: qcom: socinfo: Sort out 8974PRO names
dt-bindings: soc: qcom,smp2p: convert to dtschema
dt-bindings: qcom: geni-se: Update UART schema reference
dt-bindings: qcom: geni-se: Update I2C schema reference
dt-bindings: soc: qcom,rpmh-rsc: convert to dtschema
bus: add driver for initializing the SSC bus on (some) qcom SoCs
dt-bindings: bus: add device tree bindings for qcom,ssc-block-bus
dt-bindings: qcom: qcom,geni-se: refer to dtschema for SPI
dt-bindings: soc: qcom,smd: convert to dtschema
firmware: qcom_scm: Add compatible for MSM8976 SoC
dt-bindings: firmware: qcom-scm: Document msm8976 bindings
soc: qcom: smem: validate fields of shared structures
soc: qcom: smem: map only partitions used by local HOST
...
Link: https://lore.kernel.org/r/20220509181839.316655-1-bjorn.andersson@linaro.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
There are two drivers in arch/arm/plat-pxa: mfp and ssp. Both
of them should ideally not be needed at all, as there are
proper subsystems to replace them.
OTOH, they are self-contained and can simply be normal
SoC drivers, so move them over there to eliminate one more
of the plat-* directories.
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr> (mach-pxa)
Acked-by: Lubomir Rintel <lkundrak@v3.sk> (mach-mmp)
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The NVMe co-processor on the Apple M1 uses a DMA address filter called
SART for some DMA transactions. This adds a simple driver used to
configure the memory regions from which DMA transactions are allowed.
Unlike a real IOMMU, SART does not support any pagetables and can't be
implemented inside the IOMMU subsystem using iommu_ops.
It also can't be implemented using dma_map_ops since not all DMA
transactions of the NVMe controller are filtered by SART.
Instead, most buffers have to be registered using the integrated NVMe
IOMMU and we can't have two separate dma_map_ops implementations for a
single device.
Co-developed-by: Hector Martin <marcan@marcan.st>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Hector Martin <marcan@marcan.st>
Signed-off-by: Sven Peter <sven@svenpeter.dev>
Apple SoCs such as the M1 come with multiple embedded co-processors
running proprietary firmware. Communication with those is established
over a simple mailbox using the RTKit IPC protocol.
This cannot be implemented inside the mailbox subsystem since on top
of communication over channels we also need support for starting,
hibernating and resetting these co-processors. We also need to
handle shared memory allocations differently depending on the
co-processor and don't want to split that across multiple drivers.
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sven Peter <sven@svenpeter.dev>
In a multiplatform randconfig kernel, one can have
CONFIG_ARCH_OMAP1 enabled, but none of the specific SoCs.
This leads to some build issues as the code is not
meant to deal with this configuration at the moment:
arch/arm/mach-omap1/io.c:86:20: error: unused function 'omap1_map_common_io' [-Werror,-Wunused-function]
arch/arm/mach-omap1/pm.h:113:2: error: "Power management for this processor not implemented yet" [-Werror,-W#warnings]
Use the same trick as on OMAP2 and guard the actual compilation
of platform code with another Makefile ifdef check based
on an option that depends on having at least one SoC enabled.
The io.c file still needs to get compiled to allow building
device drivers with a dependency on CONFIG_ARCH_OMAP1.
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
There are three remaining header files that are used by omap1
specific device drivers:
- mach/soc.h provides cpu_is_omapXXX abstractions
- mach/hardware.h provides omap_read/omap_write functions
and physical addresses
- mach/mux.h provides an omap specific pinctrl abstraction
This is generally not how we do platform abstractions today,
and it would be good to completely get rid of these in favor
of passing information through platform devices and the pinctrl
subsystem.
However, given that nobody is working on that, just move it
one step forward by splitting out the header files that are
used by drivers today from the machine headers that are only
used internally.
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The register definitions in this header are used in at least four
different places, with little hope of completely cleaning that up.
Split up the file into a portion that becomes a linux-wide header
under include/linux/soc/ti/, and the parts that are actually only
needed by board files.
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The Wireless Ethernet Dispatch subsystem on the MT7622 SoC can be
configured to intercept and handle access to the DMA queues and
PCIe interrupts for a MT7615/MT7915 wireless card.
It can manage the internal WDMA (Wireless DMA) controller, which allows
ethernet packets to be passed from the packet switch engine (PSE) to the
wireless card, bypassing the CPU entirely.
This can be used to implement hardware flow offloading from ethernet to
WLAN.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull clk updates from Stephen Boyd:
"There's one large change in the core clk framework here. We change how
clk_set_rate_range() works so that the frequency is re-evaulated each
time the rate is changed. Previously we wouldn't let clk providers see
a rate that was different if it was still within the range, which
could be bad for power if the clk could run slower when a range
expands. Now the clk provider can decide to do something differently
when the constraints change. This broke Nvidia's clk driver so we had
to wait for the fix for that to bake a little more in -next.
The rate range patch series also introduced a kunit suite for the clk
framework that we're going to extend in the next release. It already
made it easy to find corner cases in the rate range patches so I'm
excited to see it cover more clk code and increase our confidence in
core framework patches in the future. I also added a kunit test for
the basic clk gate code and that work will continue to cover more
basic clk types: muxes, dividers, etc.
Beyond the core code we have the usual set of clk driver updates and
additions. Qualcomm again dominates the diffstat here with lots more
SoCs being supported and i.MX follows afer that with a similar number
of SoCs gaining clk drivers. Beyond those large additions there's
drivers being modernized to use clk_parent_data so we can move away
from global string names for all the clks in an SoC. Finally there's
lots of little fixes all over the clk drivers for typos, warnings, and
missing clks that aren't critical and get batched up waiting for the
next merge window to open. Nothing super big stands out in the driver
pile. Full details are below.
Core:
- Make clk_set_rate_range() re-evaluate the limits each time
- Introduce various clk_set_rate_range() tests
- Add clk_drop_range() to drop a previously set range
New Drivers:
- i.MXRT1050 clock driver and bindings
- i.MX8DXL clock driver and bindings
- i.MX93 clock driver and bindings
- NCO blocks on Apple SoCs
- Audio clks on StarFive JH7100 RISC-V SoC
- Add support for the new Renesas RZ/V2L SoC
- Qualcomm SDX65 A7 PLL
- Qualcomm SM6350 GPU clks
- Qualcomm SM6125, SM6350, QCS2290 display clks
- Qualcomm MSM8226 multimedia clks
Updates:
- Kunit tests for clk-gate implementation
- Terminate arrays with sentinels and make that clearer
- Cleanup SPDX tags
- Fix typos in comments
- Mark mux table as const in clk-mux
- Make the all_lists array const
- Convert Cirrus Logic CS2000P driver to regmap, yamlify DT binding
and add support for dynamic mode
- Clock configuration on Microchip PolarFire SoCs
- Free allocations on probe error in Mediatek clk driver
- Modernize Mediatek clk driver by consolidating code
- Add watchdog (WDT), I2C, and pin function controller (PFC) clocks
on Renesas R-Car S4-8
- Improve the clocks for the Rockchip rk3568 display outputs
(parenting, pll-rates)
- Use of_device_get_match_data() instead of open-coding on Rockchip
rk3568
- Reintroduce the expected fractional-divider behaviour that
disappeared with the addition of CLK_FRAC_DIVIDER_POWER_OF_TWO_PS
- Remove SYS PLL 1/2 clock gates for i.MX8M*
- Remove AUDIO MCLK ROOT from i.MX7D
- Add fracn gppll clock type used by i.MX93
- Add new composite clock for i.MX93
- Add missing media mipi phy ref clock for i.MX8MP
- Fix off by one in imx_lpcg_parse_clks_from_dt()
- Rework for the imx pll14xx
- sama7g5: One low priority fix for GCLK of PDMC
- Add DMA engine (SYS-DMAC) clocks on Renesas R-Car S4-8
- Add MOST (MediaLB I/F) clocks on Renesas R-Car E3 and D3
- Add CAN-FD clocks on Renesas R-Car V3U
- Qualcomm SC8280XP RPMCC
- Add some missing clks on Qualcomm MSM8992/MSM8994/MSM8998 SoCs
- Rework Qualcomm GCC bindings and convert SDM845 camera bindig to
YAML
- Convert various Qualcomm drivers to use clk_parent_data
- Remove test clocks from various Qualcomm drivers
- Crypto engine clks on Qualcomm IPQ806x + more freqs for SDCC/NSS
- Qualcomm SM8150 EMAC, PCIe, UFS GDSCs
- Better pixel clk frequency support on Qualcomm RCG2 clks"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (227 commits)
clk: zynq: Update the parameters to zynq_clk_register_periph_clk
clk: zynq: trivial warning fix
clk: Drop the rate range on clk_put()
clk: test: Test clk_set_rate_range on orphan mux
clk: Initialize orphan req_rate
dt-bindings: clock: drop useless consumer example
dt-bindings: clock: renesas: Make example 'clocks' parsable
clk: qcom: gcc-msm8994: Fix gpll4 width
dt-bindings: clock: fix dt_binding_check error for qcom,gcc-other.yaml
clk: rs9: Add Renesas 9-series PCIe clock generator driver
clk: fixed-factor: Introduce devm_clk_hw_register_fixed_factor_index()
clk: visconti: prevent array overflow in visconti_clk_register_gates()
dt-bindings: clk: rs9: Add Renesas 9-series I2C PCIe clock generator
clk: sifive: Move all stuff into SoCs header files from C files
clk: sifive: Add SoCs prefix in each SoCs-dependent data
riscv: dts: Change the macro name of prci in each device node
dt-bindings: change the macro name of prci in header files and example
clk: sifive: duplicate the macro definitions for the time being
clk: qcom: sm6125-gcc: fix typos in comments
clk: ti: clkctrl: fix typos in comments
...
Pull mailbox updates from Jassi Brar:
"qcom:
- add support for MSM8976
mtk:
- enable mt8186
- add ADSP controller driver
ti:
- use poll mode during suspend
tegra:
- fix tx channel flush
imx:
- add i.MX8 SECO MU support
- prepare for, and add iMX93 support"
* tag 'mailbox-v5.18' of git://git.linaro.org/landing-teams/working/fujitsu/integration:
dt-bindings: mailbox: add definition for mt8186
mailbox: ti-msgmgr: Operate mailbox in polled mode during system suspend
mailbox: ti-msgmgr: Refactor message read during interrupt handler
mailbox: imx: support i.MX93 S401 MU
mailbox: imx: support dual interrupts
mailbox: imx: extend irq to an array
dt-bindings: mailbox: imx-mu: add i.MX93 S4 MU support
dt-bindings: mailbox: imx-mu: add i.MX93 MU
mailbox: imx: add i.MX8 SECO MU support
mailbox: imx: introduce rxdb callback
dt-bindings: mailbox: imx-mu: add i.MX8 SECO MU support
mailbox: imx: enlarge timeout while reading/writing messages to SCFW
mailbox: imx: fix crash in resume on i.mx8ulp
mailbox: imx: fix wakeup failure from freeze mode
mailbox: mediatek: add support for adsp mailbox controller
dt-bindings: mailbox: mtk,adsp-mbox: add mtk adsp-mbox document
mailbox: qcom-apcs-ipc: Add compatible for MSM8976 SoC
dt-bindings: mailbox: Add compatible for the MSM8976
mailbox: tegra-hsp: Flush whole channel
Pull ARM driver updates from Arnd Bergmann:
"There are a few separately maintained driver subsystems that we merge
through the SoC tree, notable changes are:
- Memory controller updates, mainly for Tegra and Mediatek SoCs, and
clarifications for the memory controller DT bindings
- SCMI firmware interface updates, in particular a new transport
based on OPTEE and support for atomic operations.
- Cleanups to the TEE subsystem, refactoring its memory management
For SoC specific drivers without a separate subsystem, changes include
- Smaller updates and fixes for TI, AT91/SAMA5, Qualcomm and NXP
Layerscape SoCs.
- Driver support for Microchip SAMA5D29, Tesla FSD, Renesas RZ/G2L,
and Qualcomm SM8450.
- Better power management on Mediatek MT81xx, NXP i.MX8MQ and older
NVIDIA Tegra chips"
* tag 'arm-drivers-5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (154 commits)
ARM: spear: fix typos in comments
soc/microchip: fix invalid free in mpfs_sys_controller_delete
soc: s4: Add support for power domains controller
dt-bindings: power: add Amlogic s4 power domains bindings
ARM: at91: add support in soc driver for new SAMA5D29
soc: mediatek: mmsys: add sw0_rst_offset in mmsys driver data
dt-bindings: memory: renesas,rpc-if: Document RZ/V2L SoC
memory: emif: check the pointer temp in get_device_details()
memory: emif: Add check for setup_interrupts
dt-bindings: arm: mediatek: mmsys: add support for MT8186
dt-bindings: mediatek: add compatible for MT8186 pwrap
soc: mediatek: pwrap: add pwrap driver for MT8186 SoC
soc: mediatek: mmsys: add mmsys reset control for MT8186
soc: mediatek: mtk-infracfg: Disable ACP on MT8192
soc: ti: k3-socinfo: Add AM62x JTAG ID
soc: mediatek: add MTK mutex support for MT8186
soc: mediatek: mmsys: add mt8186 mmsys routing table
soc: mediatek: pm-domains: Add support for mt8186
dt-bindings: power: Add MT8186 power domains
soc: mediatek: pm-domains: Add support for mt8195
...
During the system suspend path we must set all queues to operate in
polled mode as it is possible for any protocol built using this mailbox,
such as TISCI, to require communication during the no irq phase of suspend,
and we cannot rely on interrupts there.
Polled mode is implemented by allowing the mailbox user to define an
RX channel as part of the message that is sent which is what gets polled
for a response. If polled mode is enabled, this will immediately be
polled for a response at the end of the mailbox send_data op before
returning success for the data send or timing out if no response is
received.
Finally, to ensure polled mode is always enabled during system suspend,
iterate through all queues to set RX queues to polled mode during system
suspend and disable polled mode for all in the resume handler.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Qualcomm driver updates for v5.18
This refactors the Qualcomm mdt file loader, to partially decouple it
from the SCM peripheral-authentication-service. This is needed as newer
platforms, such as the Qualcomm SM8450, require the metadata to remain
accessible to TrustZone during a longer time. This is followed by the
introduction of remoteproc drivers for SM8450 (Snapdragon 8 Gen 1).
It changes the way hardware version differences are handled in the LLCC
driver and introduces support for Qualcomm SM8450. While updating the dt
binding for LLCC it also introduces the missing SM8350 compatible.
The ocmem and aoss drivers gains missing put_device() calls and rpmpd
gains a missing check for kcalloc() failure.
The SPM driver is updated to avoid instantiating the SPM cpuidle devices
if the CPUs aren't controlled by SPM, such as when Snapdragon 8916
operates in 32-bit mode without PSCI.
The RPM power-domain driver gains MSM8226 support.
Lastly the socinfo driver gains knowledge about a few new SoCs and
PMICs.
* tag 'qcom-drivers-for-5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux: (37 commits)
soc: qcom: rpmpd: Add MSM8226 support
dt-bindings: power: rpmpd: Add MSM8226 to rpmpd binding
soc: qcom: mdt_loader: Fix split-firmware condition
dt-bindings: arm: msm: Add LLCC compatible for SM8450
dt-bindings: arm: msm: Add LLCC compatible for SM8350
soc: qcom: llcc: Add configuration data for SM8450 SoC
soc: qcom: llcc: Update register offsets for newer LLCC HW
soc: qcom: llcc: Add missing llcc configuration data
soc: qcom: llcc: Add write-cache cacheable support
soc: qcom: llcc: Update the logic for version info extraction
soc: qcom: llcc: Add support for 16 ways of allocation
soc: qcom: socinfo: Add some more PMICs and SoCs
firmware: qcom: scm: Add support for MC boot address API
firmware: qcom: scm: Drop cpumask parameter from set_boot_addr()
firmware: qcom: scm: Simplify set_cold/warm_boot_addr()
cpuidle: qcom-spm: Check if any CPU is managed by SPM
remoteproc: qcom: pas: Add SM8450 remoteproc support
dt-bindings: remoteproc: qcom: pas: Add SM8450 PAS compatibles
remoteproc: qcom: pas: Carry PAS metadata context
soc: qcom: mdt_loader: Extract PAS operations
...
Link: https://lore.kernel.org/r/20220301042055.1804859-1-bjorn.andersson@linaro.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- add power domains support for mt8195
- disable ACP on mt8192
mt8186:
- add support for power domains
- add mmsys and mutex support needed for DRM
- add reset control based on mmsys subsystem
- add pmic wrapper
* tag 'v5.17-next-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/matthias.bgg/linux:
dt-bindings: arm: mediatek: mmsys: add support for MT8186
dt-bindings: mediatek: add compatible for MT8186 pwrap
soc: mediatek: pwrap: add pwrap driver for MT8186 SoC
soc: mediatek: mmsys: add mmsys reset control for MT8186
soc: mediatek: mtk-infracfg: Disable ACP on MT8192
soc: mediatek: add MTK mutex support for MT8186
soc: mediatek: mmsys: add mt8186 mmsys routing table
soc: mediatek: pm-domains: Add support for mt8186
dt-bindings: power: Add MT8186 power domains
soc: mediatek: pm-domains: Add support for mt8195
soc: mediatek: pm-domains: Move power status offset to power domain data
soc: mediatek: pm-domains: Remove unused macro
soc: mediatek: pm-domains: Add wakeup capacity support in power domain
dt-bindings: power: Add MT8195 power domains
Link: https://lore.kernel.org/r/16a53482-5a8c-e95e-8cd4-b8304f110987@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
If we access the syscon (expansion bus config registers) using the
syscon regmap instead of relying on direct accessor functions,
we do not need to call this static code in the machine
(arch/arm/mach-ixp4xx/common.c) which makes things less dependent
on custom machine-dependent code.
Look up the syscon regmap and handle the error: this will make
deferred probe work with relation to the syscon.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20220211223238.648934-8-linus.walleij@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
LLCC HW version info is made up of major, branch, minor and echo
version bits each of which are 8bits. Several features in newer
LLCC HW are based on the full version rather than just major or
minor versions such as write-subcache enable which is applicable
for versions v2.0.0.0 and later, also upcoming write-subcache
cacheable for SM8450 SoC which is only present in versions v2.1.0.0
and later, so it makes it easier and cleaner to just directly
compare with the full version than adding additional major/branch/
minor/echo version checks. So remove the earlier major version check
and add full version check for those features.
Signed-off-by: Sai Prakash Ranjan <quic_saipraka@quicinc.com>
Tested-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/a82d7c32348c51fcc2b63e220d91b318bf706c83.1643355594.git.quic_saipraka@quicinc.com
Rather than passing a boolean to indicate if the PAS operations should
be performed from within __mdt_load(), extract them to their own helper
function.
This will allow clients to invoke this directly, with some
qcom_scm_pas_metadata context that they later needs to release, without
further having to complicate the prototype of qcom_mdt_load().
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20220128025513.97188-9-bjorn.andersson@linaro.org
It's been observed that some firmware found in a Qualcomm SM8450 device
has the hash table in a separate .bNN file. Use the newly extracted
helper function to load this segment from the separate file, if it's
determined that the hashes are not part of the already loaded firmware.
In order to do this, the function needs access to the firmware basename
and to provide more useful error messages a struct device to associate
the errors with.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20220128025513.97188-4-bjorn.andersson@linaro.org
Pull MSI irq updates from Thomas Gleixner:
"Rework of the MSI interrupt infrastructure.
This is a treewide cleanup and consolidation of MSI interrupt handling
in preparation for further changes in this area which are necessary
to:
- address existing shortcomings in the VFIO area
- support the upcoming Interrupt Message Store functionality which
decouples the message store from the PCI config/MMIO space"
* tag 'irq-msi-2022-01-13' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (94 commits)
genirq/msi: Populate sysfs entry only once
PCI/MSI: Unbreak pci_irq_get_affinity()
genirq/msi: Convert storage to xarray
genirq/msi: Simplify sysfs handling
genirq/msi: Add abuse prevention comment to msi header
genirq/msi: Mop up old interfaces
genirq/msi: Convert to new functions
genirq/msi: Make interrupt allocation less convoluted
platform-msi: Simplify platform device MSI code
platform-msi: Let core code handle MSI descriptors
bus: fsl-mc-msi: Simplify MSI descriptor handling
soc: ti: ti_sci_inta_msi: Remove ti_sci_inta_msi_domain_free_irqs()
soc: ti: ti_sci_inta_msi: Rework MSI descriptor allocation
NTB/msi: Convert to msi_on_each_desc()
PCI: hv: Rework MSI handling
powerpc/mpic_u3msi: Use msi_for_each-desc()
powerpc/fsl_msi: Use msi_for_each_desc()
powerpc/pasemi/msi: Convert to msi_on_each_dec()
powerpc/cell/axon_msi: Convert to msi_on_each_desc()
powerpc/4xx/hsta: Rework MSI handling
...
Qualcomm driver updates for v5.17
This introduces RPM power-domain support for the SM8450, SM6125 and
QCM2290 platforms. It them clean up the platform-based naming of the
resources definitions throughout the RPMh PD driver.
The last-level cache controller driver gains SM8350 support.
The RPM sleep stats driver gains support for several older systems that
had a slightly different memory layout for this information.
The socinfo gains SM8450, SM6350 and SM7227 definitions.
In addition to the DeviceTree binding updates related to these changes
new compatibles was added to describe the SM8450 and the Kryo 780 CPU.
Lastly a few typo and style fixes are introduced.
* tag 'qcom-drivers-for-5.17' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux: (27 commits)
soc: qcom: rpmh-rsc: Fix typo in a comment
soc: qcom: socinfo: Add SM6350 and SM7225
dt-bindings: arm: msm: Don't mark LLCC interrupt as required
dt-bindings: firmware: scm: Add SM6350 compatible
dt-bindings: arm: msm: Add LLCC for SM6350
soc: qcom: rpmhpd: Sort power-domain definitions and lists
soc: qcom: rpmhpd: Remove mx/cx relationship on sc7280
soc: qcom: rpmhpd: Rename rpmhpd struct names
soc: qcom: rpmhpd: sm8450: Add the missing .peer for sm8450_cx_ao
soc: qcom: socinfo: add SM8450 ID
soc: qcom: rpmhpd: Add SM8450 power domains
dt-bindings: power: rpmpd: Add SM8450 to rpmpd binding
soc: qcom: smem: Update max processor count
dt-bindings: arm: qcom: Document SM8450 SoC and boards
dt-bindings: firmware: scm: Add SM8450 compatible
dt-bindings: arm: cpus: Add kryo780 compatible
soc: qcom: rpmpd: Add support for sm6125
dt-bindings: qcom-rpmpd: Add sm6125 power domains
soc: qcom: aoss: constify static struct thermal_cooling_device_ops
PM: AVS: qcom-cpr: Use div64_ul instead of do_div
...
Link: https://lore.kernel.org/r/20211221040452.3620633-1-bjorn.andersson@linaro.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
R-Car Gen3 SoC series has a realtime processor, the boot
address of this processor can be set thanks to CR7BAR register
of the reset module.
Export this function so that it's possible to set the boot
address from a remoteproc driver.
Also drop the __initdata qualifier on rcar_rst_base,
since we will use this address later than init time.
Signed-off-by: Julien Massot <julien.massot@iot.bzh>
Link: https://lore.kernel.org/r/20211022122101.66998-1-julien.massot@iot.bzh
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Pull clk updates from Stephen Boyd:
"The usual collection of clk driver updates and new driver additions.
In terms of lines it's mainly Qualcomm and Mediatek code, supporting
various SoCs and their multitude of clk controllers.
New Drivers:
- GCC and RPMcc support for Qualcomm QCM2290 SoCs
- GCC support for Qualcomm MSM8994/MSM8992 SoCs
- LPASSCC and CAMCC support for Qualcomm SC7280 SoCs
- Support for Mediatek MT8195 SoCs
- Initial clock driver for the Exynos850 SoC
- Add i.MX8ULP clock driver and related bindings
Updates:
- Clock power management for new SAMA7G5 SoC
- Updates to the master clock driver and sam9x60-pll to be able to
use cpufreq-dt driver and avoid overclocking of CPU and MCK0
domains while changing the frequency via DVFS
- Use ARRAY_SIZE in qcom clk drivers
- Remove some impractical fallback parent names in qcom clk drivers
- Make Mediatek clk drivers tristate
- Refactoring of the CPU clock code and conversion of Samsung
Exynos5433 CPU clock driver to the platform driver
- A few conversions to devm_platform_ioremap_resource()
- Updates of the Samsung Kconfig help text
- Update video path realted clocks for Amlogic meson8
- Add SPI Multi I/O Bus and SDHI clocks and resets on Renesas RZ/G2L
- Add SPI Multi I/O Bus (RPC) clocks on Renesas R-Car V3U
- Add MediaLB clocks on Renesas R-Car H3, M3-W/W+, and M3-N
- Remove unused helpers from i.MX specific clock header
- Rework all i.MX clk based helpers to use clk_hw based ones
- Rework i.MX gate/mux/divider wrappers
- Rework imx_clk_hw_composite and imx_clk_hw_pll14xx wrappers
- Update i.MX pllv4 and composite clocks to support i.MX8ULP
- Disable i.MX7ULP composite clock during initialization
- Add CLK_SET_RATE_NO_REPARENT flag to the i.MX7ULP composite
- Disable the i.MX pfd when set pfdv2 clock rate
- Add support for i.MX8ULP in pfdv2
- Add the pcc reset controller support on i.MX8ULP
- Fix the build break when clk-imx8ulp is built as module
- Move csi_sel mux to correct base register in i.MX6UL clock drivr
- Fix csi clk gate register in i.MX6UL clock driver
- Fix build bug making CLK_IMX8ULP select MXC_CLK
- Add TPU (PWM), and Z (Cortex-A76) clocks on Renesas R-Car V3U
- Add Ethernet clocks on Renesas RZ/G2L
- Move Rockchip to use module_platform_probe
- Enable usage of Coresight related clocks on Rockchip rk3399"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (170 commits)
clk: use clk_core_get_rate_recalc() in clk_rate_get()
clk: at91: sama7g5: set low limit for mck0 at 32KHz
clk: at91: sama7g5: remove prescaler part of master clock
clk: at91: clk-master: add notifier for divider
clk: at91: clk-sam9x60-pll: add notifier for div part of PLL
clk: at91: clk-master: fix prescaler logic
clk: at91: clk-master: mask mckr against layout->mask
clk: at91: clk-master: check if div or pres is zero
clk: at91: sam9x60-pll: use DIV_ROUND_CLOSEST_ULL
clk: at91: pmc: add sama7g5 to the list of available pmcs
clk: at91: clk-master: improve readability by using local variables
clk: at91: clk-master: add register definition for sama7g5's master clock
clk: at91: sama7g5: add securam's peripheral clock
clk: at91: pmc: execute suspend/resume only for backup mode
clk: at91: re-factor clocks suspend/resume
clk: ux500: Add driver for the reset portions of PRCC
dt-bindings: clock: u8500: Rewrite in YAML and extend
clk: composite: Use rate_ops.determine_rate when also a mux is available
clk: samsung: describe drivers in Kconfig
clk: samsung: exynos5433: update apollo and atlas clock probing
...
Pull ARM SoC driver updates from Arnd Bergmann:
"These are all the driver updates for SoC specific drivers. There are a
couple of subsystems with individual maintainers picking up their
patches here:
- The reset controller subsystem add support for a few new SoC
variants to existing drivers, along with other minor improvements
- The OP-TEE subsystem gets a driver for the ARM FF-A transport
- The memory controller subsystem has improvements for Tegra,
Mediatek, Renesas, Freescale and Broadcom specific drivers.
- The tegra cpuidle driver changes get merged through this tree this
time. There are only minor changes, but they depend on other tegra
driver updates here.
- The ep93xx platform finally moves to using the drivers/clk/
subsystem, moving the code out of arch/arm in the process. This
depends on a small sound driver change that is included here as
well.
- There are some minor updates for Qualcomm and Tegra specific
firmware drivers.
The other driver updates are mainly for drivers/soc, which contains a
mixture of vendor specific drivers that don't really fit elsewhere:
- Mediatek drivers gain more support for MT8192, with new support for
hw-mutex and mmsys routing, plus support for reset lines in the
mmsys driver.
- Qualcomm gains a new "sleep stats" driver, and support for the
"Generic Packet Router" in the APR driver.
- There is a new user interface for routing the UARTS on ASpeed BMCs,
something that apparently nobody else has needed so far.
- More drivers can now be built as loadable modules, in particular
for Broadcom and Samsung platforms.
- Lots of improvements to the TI sysc driver for better
suspend/resume support"
Finally, there are lots of minor cleanups and new device IDs for
amlogic, renesas, tegra, qualcomm, mediateka, samsung, imx,
layerscape, allwinner, broadcom, and omap"
* tag 'drivers-5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (179 commits)
optee: Fix spelling mistake "reclain" -> "reclaim"
Revert "firmware: qcom: scm: Add support for MC boot address API"
qcom: spm: allow compile-testing
firmware: arm_ffa: Remove unused 'compat_version' variable
soc: samsung: exynos-chipid: add exynosautov9 SoC support
firmware: qcom: scm: Don't break compile test on non-ARM platforms
soc: qcom: smp2p: Add of_node_put() before goto
soc: qcom: apr: Add of_node_put() before return
soc: qcom: qcom_stats: Fix client votes offset
soc: qcom: rpmhpd: fix sm8350_mxc's peer domain
dt-bindings: arm: cpus: Document qcom,msm8916-smp enable-method
ARM: qcom: Add qcom,msm8916-smp enable-method identical to MSM8226
firmware: qcom: scm: Add support for MC boot address API
soc: qcom: spm: Add 8916 SPM register data
dt-bindings: soc: qcom: spm: Document qcom,msm8916-saw2-v3.0-cpu
soc: qcom: socinfo: Add PM8150C and SMB2351 models
firmware: qcom_scm: Fix error retval in __qcom_scm_is_call_available()
soc: aspeed: Add UART routing support
soc: fsl: dpio: rename the enqueue descriptor variable
soc: fsl: dpio: use an explicit NULL instead of 0
...
Pull sound updates from Takashi Iwai:
"Lots of code development have been see in ASoC side as usual, while
the continued development on memalloc helper and USB-audio low-
latency support are found in the rest.
Note that a few changes in the unusual places like arch/sh are
included, which are a part of ASoC DAI format cleanups.
ALSA core:
- Continued memalloc helper updates and cleanups, now supporting
non-coherent and non-contiguous pages
- Fixes for races in mixer OSS layer
ASoC:
- A new version of the audio graph card which supports a wider range
of systems
- Several conversions to YAML DT bindings
- Continuing cleanups to the SOF and Intel code
- Move of the Cirrus DSP framework into drivers/firmware to allow for
future use by non-audio DSPs
- An overhaul of the cs42l42 driver, correcting many problems
- DAI format terminology conversions over many drivers for cleanups
- Support for AMD Vangogh and Yelow Cap, Cirrus CS35L41, Maxim
MAX98520 and MAX98360A, Mediatek MT8195, Nuvoton NAU8821, nVidia
Tegra210, NXP i.MX8ULP, Qualcomm AudioReach, Realtek ALC5682I-VS,
RT5682S, and RT9120 and Rockchip RV1126 and RK3568
USB-audio:
- Continued improvements on low-latency playback
- Quirks for Pioneer devices, Line6 HX-Stomp XL, Audient iD14
HD-audio:
- Reduce excessive udelay() calls on Intel platforms; this should
reduce the CPU load with PulseAudio
- Quirks for HP and Clevo laptops
FireWire:
- Support for meter information on MOTU"
* tag 'sound-5.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (513 commits)
ALSA: usb-audio: Add quirk for Audient iD14
ALSA: hda/realtek: Add quirk for Clevo PC70HS
ALSA: usb-audio: Line6 HX-Stomp XL USB_ID for 48k-fixed quirk
ALSA: usb-audio: Add registration quirk for JBL Quantum 400
ASoC: rsnd: Fix an error handling path in 'rsnd_node_count()'
ASoC: tlv320aic3x: Make aic3x_remove() return void
ASoC: Intel: soc-acpi: use const for all uses of snd_soc_acpi_codecs
ASoC: Intel: soc-acpi-cht: shrink tables using compatible IDs
ASoC: Intel: soc-acpi-byt: shrink tables using compatible IDs
ASoC: Intel: sof_rt5682: use comp_ids to enumerate rt5682s
ASoC: Intel: sof_rt5682: detect codec variant in probe function
ASoC: soc-acpi: add comp_ids field for machine driver matching
ASoC: mediatek: mt8195: add mt8195-mt6359-rt1011-rt5682 bindings document
ASoC: mediatek: mt8195: add machine driver with mt6359, rt1011 and rt5682
ASoC: Stop dummy from overriding hwparams
ASoC: topology: Change topology device to card device
ASoC: topology: Use correct device for prints
ASoC: topology: Check for dapm widget completeness
ASoC: topology: Add header payload_size verification
ASoC: core: Remove invalid snd_soc_component_set_jack call
...
Samsung SoC drivers changes for v5.16
1. Convert Exynos ChipID and ASV driver to a module and make it a
default, instead of selected. The driver is not essential, so it
could be disabled, if needed.
2. Add support for Exynos850 and Exynos Auto v9 to Exynos ChipID and ASV
driver.
3. Get rid of HAVE_S3C_RTC because it was adding just another layer
instead of direct dependencies.
4. Minor cleanups.
* tag 'samsung-drivers-5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
soc: samsung: exynos-chipid: add exynosautov9 SoC support
rtc: s3c: remove HAVE_S3C_RTC in favor of direct dependencies
soc: samsung: exynos-chipid: Add Exynos850 support
dt-bindings: samsung: exynos-chipid: Document Exynos850 compatible
soc: samsung: exynos-chipid: Pass revision reg offsets
soc: samsung: pm_domains: drop unused is_off field
arm64: exynos: don't have ARCH_EXYNOS select EXYNOS_CHIPID
soc: samsung: exynos-chipid: do not enforce built-in
soc: samsung: exynos-chipid: convert to a module
soc: samsung: exynos-chipid: avoid soc_device_to_device()
soc: samsung: exynos-pmu: Fix compilation when nothing selects CONFIG_MFD_CORE
Link: https://lore.kernel.org/r/20211026094709.75692-2-krzysztof.kozlowski@canonical.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
