For some reason they tend to squat on the very first CSR/
Cambridge Silicon Radio VID/PID instead of paying fees.
This is an extremely common problem; the issue goes as back as 2013
and these devices are only getting more popular, even rebranded by
reputable vendors and sold by retailers everywhere.
So, at this point in time there are hundreds of modern dongles reusing
the ID of what originally was an early Bluetooth 1.1 controller.
Linux is the only place where they don't work due to spotty checks
in our detection code. It only covered a minimum subset.
So what's the big idea? Take advantage of the fact that all CSR
chips report the same internal version as both the LMP sub-version and
HCI revision number. It always matches, couple that with the manufacturer
code, that rarely lies, and we now have a good idea of who is who.
Additionally, by compiling a list of user-reported HCI/lsusb dumps, and
searching around for legit CSR dongles in similar product ranges we can
find what CSR BlueCore firmware supported which Bluetooth versions.
That way we can narrow down ranges of fakes for each of them.
e.g. Real CSR dongles with LMP subversion 0x73 are old enough that
support BT 1.1 only; so it's a dead giveaway when some
third-party BT 4.0 dongle reuses it.
So, to sum things up; there are multiple classes of fake controllers
reusing the same 0A12:0001 VID/PID. This has been broken for a while.
Known 'fake' bcdDevices: 0x0100, 0x0134, 0x1915, 0x2520, 0x7558, 0x8891
IC markings on 0x7558: FR3191AHAL 749H15143 (???)
https://bugzilla.kernel.org/show_bug.cgi?id=60824
Fixes: 81cac64ba2 (Deal with USB devices that are faking CSR vendor)
Reported-by: Michał Wiśniewski <brylozketrzyn@gmail.com>
Tested-by: Mike Johnson <yuyuyak@gmail.com>
Tested-by: Ricardo Rodrigues <ekatonb@gmail.com>
Tested-by: M.Hanny Sabbagh <mhsabbagh@outlook.com>
Tested-by: Oussama BEN BRAHIM <b.brahim.oussama@gmail.com>
Tested-by: Ismael Ferreras Morezuelas <swyterzone@gmail.com>
Signed-off-by: Ismael Ferreras Morezuelas <swyterzone@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Starting with the upgrade to v5.8-rc3, I've noticed I wasn't able to
connect to my Bluetooth headset properly anymore. While connecting to
the device would eventually succeed, bluetoothd seemed to be confused
about the current connection state where the state was flapping hence
and forth. Bisecting this issue led to commit 3ca44c16b0 (Bluetooth:
Consolidate encryption handling in hci_encrypt_cfm, 2020-05-19), which
refactored `hci_encrypt_cfm` to also handle updating the connection
state.
The commit in question changed the code to call `hci_connect_cfm` inside
`hci_encrypt_cfm` and to change the connection state. But with the
conversion, we now only update the connection state if a status was set
already. In fact, the reverse should be true: the status should be
updated if no status is yet set. So let's fix the isuse by reversing the
condition.
Fixes: 3ca44c16b0 ("Bluetooth: Consolidate encryption handling in hci_encrypt_cfm")
Signed-off-by: Patrick Steinhardt <ps@pks.im>
Acked-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When the extended advertisement feature is enabled, a hardcoded min and
max interval of 0x8000 is used. This patch fixes this issue by using
the configured min/max value.
This was validated by setting min/max in main.conf and making sure the
right setting is applied:
< HCI Command: LE Set Extended Advertising Parameters (0x08|0x0036) plen
25 #93 [hci0] 10.953011
…
Min advertising interval: 181.250 msec (0x0122)
Max advertising interval: 181.250 msec (0x0122)
…
Signed-off-by: Alain Michaud <alainm@chromium.org>
Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Reviewed-by: Daniel Winkler <danielwinkler@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
If user decides to cancel the ongoing pairing process (e.g. by clicking
the cancel button on pairing/passkey window), abort any ongoing pairing
and then terminate the link if it was created because of the pair
device action.
Signed-off-by: Manish Mandlik <mmandlik@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This calls hci_update_background_scan() when there is any update on the
advertisement monitors. If there is at least one advertisement monitor,
the filtering policy of scan parameters should be 0x00. This also reports
device found mgmt events if there is at least one monitor.
The following cases were tested with btmgmt advmon-* commands.
(1) add a ADV monitor and observe that the passive scanning is
triggered.
(2) remove the last ADV monitor and observe that the passive scanning is
terminated.
(3) with a LE peripheral paired, repeat (1) and observe the passive
scanning continues.
(4) with a LE peripheral paired, repeat (2) and observe the passive
scanning continues.
(5) with a ADV monitor, suspend/resume the host and observe the passive
scanning continues.
Signed-off-by: Miao-chen Chou <mcchou@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This adds the request handler of MGMT_OP_REMOVE_ADV_MONITOR command.
Note that the controller-based monitoring is not yet in place. This
removes the internal monitor(s) without sending HCI traffic, so the
request returns immediately.
The following test was performed.
- Issue btmgmt advmon-remove with valid and invalid handles.
Signed-off-by: Miao-chen Chou <mcchou@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This adds the request handler of MGMT_OP_ADD_ADV_PATTERNS_MONITOR command.
Note that the controller-based monitoring is not yet in place. This tracks
the content of the monitor without sending HCI traffic, so the request
returns immediately.
The following manual test was performed.
- Issue btmgmt advmon-add with valid and invalid inputs.
- Issue btmgmt advmon-add more the allowed number of monitors.
Signed-off-by: Miao-chen Chou <mcchou@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This adds the request handler of MGMT_OP_READ_ADV_MONITOR_FEATURES
command. Since the controller-based monitoring is not yet in place, this
report only the supported features but not the enabled features.
The following test was performed.
- Issuing btmgmt advmon-features.
Signed-off-by: Miao-chen Chou <mcchou@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Replace the wakeable boolean with flags in hci_conn_params and all users
of this boolean. This will be used by the get/set device flags mgmt op.
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Reviewed-by: Alain Michaud <alainm@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This patch centralized the initialization of default parameters. This
is required to allow clients to more easily customize the default
system parameters.
Signed-off-by: Alain Michaud <alainm@chromium.org>
Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch submits the corresponding kernel definitions to mgmt.h.
This is submitted before the implementation to avoid any conflicts in
values allocations.
Signed-off-by: Alain Michaud <alainm@chromium.org>
Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Reviewed-by: Yu Liu <yudiliu@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This change implements suggestions from the code review of the SCO CMSG
state flag patch.
Signed-off-by: Alain Michaud <alainm@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This change adds support for reporting the BT_PKT_STATUS to the socket
CMSG data to allow the implementation of a packet loss correction on
erroneous data received on the SCO socket.
The patch was partially developed by Marcel Holtmann and validated by
Hsin-yu Chao.
Signed-off-by: Alain Michaud <alainm@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Extend bpf() syscall subcommands that operate on bpf_link, that is
LINK_CREATE, LINK_UPDATE, OBJ_GET_INFO, to accept attach types tied to
network namespaces (only flow dissector at the moment).
Link-based and prog-based attachment can be used interchangeably, but only
one can exist at a time. Attempts to attach a link when a prog is already
attached directly, and the other way around, will be met with -EEXIST.
Attempts to detach a program when link exists result in -EINVAL.
Attachment of multiple links of same attach type to one netns is not
supported with the intention to lift the restriction when a use-case
presents itself. Because of that link create returns -E2BIG when trying to
create another netns link, when one already exists.
Link-based attachments to netns don't keep a netns alive by holding a ref
to it. Instead links get auto-detached from netns when the latter is being
destroyed, using a pernet pre_exit callback.
When auto-detached, link lives in defunct state as long there are open FDs
for it. -ENOLINK is returned if a user tries to update a defunct link.
Because bpf_link to netns doesn't hold a ref to struct net, special care is
taken when releasing, updating, or filling link info. The netns might be
getting torn down when any of these link operations are in progress. That
is why auto-detach and update/release/fill_info are synchronized by the
same mutex. Also, link ops have to always check if auto-detach has not
happened yet and if netns is still alive (refcnt > 0).
Signed-off-by: Jakub Sitnicki <jakub@cloudflare.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200531082846.2117903-5-jakub@cloudflare.com
Move functions to manage BPF programs attached to netns that are not
specific to flow dissector to a dedicated module named
bpf/net_namespace.c.
The set of functions will grow with the addition of bpf_link support for
netns attached programs. This patch prepares ground by creating a place
for it.
This is a code move with no functional changes intended.
Signed-off-by: Jakub Sitnicki <jakub@cloudflare.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200531082846.2117903-4-jakub@cloudflare.com
In order to:
(1) attach more than one BPF program type to netns, or
(2) support attaching BPF programs to netns with bpf_link, or
(3) support multi-prog attach points for netns
we will need to keep more state per netns than a single pointer like we
have now for BPF flow dissector program.
Prepare for the above by extracting netns_bpf that is part of struct net,
for storing all state related to BPF programs attached to netns.
Turn flow dissector callbacks for querying/attaching/detaching a program
into generic ones that operate on netns_bpf. Next patch will move the
generic callbacks into their own module.
This is similar to how it is organized for cgroup with cgroup_bpf.
Signed-off-by: Jakub Sitnicki <jakub@cloudflare.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Cc: Stanislav Fomichev <sdf@google.com>
Link: https://lore.kernel.org/bpf/20200531082846.2117903-3-jakub@cloudflare.com
KTLS uses a stream parser to collect TLS messages and send them to
the upper layer tls receive handler. This ensures the tls receiver
has a full TLS header to parse when it is run. However, when a
socket has BPF_SK_SKB_STREAM_VERDICT program attached before KTLS
is enabled we end up with two stream parsers running on the same
socket.
The result is both try to run on the same socket. First the KTLS
stream parser runs and calls read_sock() which will tcp_read_sock
which in turn calls tcp_rcv_skb(). This dequeues the skb from the
sk_receive_queue. When this is done KTLS code then data_ready()
callback which because we stacked KTLS on top of the bpf stream
verdict program has been replaced with sk_psock_start_strp(). This
will in turn kick the stream parser again and eventually do the
same thing KTLS did above calling into tcp_rcv_skb() and dequeuing
a skb from the sk_receive_queue.
At this point the data stream is broke. Part of the stream was
handled by the KTLS side some other bytes may have been handled
by the BPF side. Generally this results in either missing data
or more likely a "Bad Message" complaint from the kTLS receive
handler as the BPF program steals some bytes meant to be in a
TLS header and/or the TLS header length is no longer correct.
We've already broke the idealized model where we can stack ULPs
in any order with generic callbacks on the TX side to handle this.
So in this patch we do the same thing but for RX side. We add
a sk_psock_strp_enabled() helper so TLS can learn a BPF verdict
program is running and add a tls_sw_has_ctx_rx() helper so BPF
side can learn there is a TLS ULP on the socket.
Then on BPF side we omit calling our stream parser to avoid
breaking the data stream for the KTLS receiver. Then on the
KTLS side we call BPF_SK_SKB_STREAM_VERDICT once the KTLS
receiver is done with the packet but before it posts the
msg to userspace. This gives us symmetry between the TX and
RX halfs and IMO makes it usable again. On the TX side we
process packets in this order BPF -> TLS -> TCP and on
the receive side in the reverse order TCP -> TLS -> BPF.
Discovered while testing OpenSSL 3.0 Alpha2.0 release.
Fixes: d829e9c411 ("tls: convert to generic sk_msg interface")
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/159079361946.5745.605854335665044485.stgit@john-Precision-5820-Tower
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Add xdp_txq_info as the Tx counterpart to xdp_rxq_info. At the
moment only the device is added. Other fields (queue_index)
can be added as use cases arise.
>From a UAPI perspective, add egress_ifindex to xdp context for
bpf programs to see the Tx device.
Update the verifier to only allow accesses to egress_ifindex by
XDP programs with BPF_XDP_DEVMAP expected attach type.
Signed-off-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Toke Høiland-Jørgensen <toke@redhat.com>
Link: https://lore.kernel.org/bpf/20200529220716.75383-4-dsahern@kernel.org
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
A node that has the MRA role, it can behave as MRM or MRC.
Initially it starts as MRM and sends MRP_Test frames on both ring ports.
If it detects that there are MRP_Test send by another MRM, then it
checks if these frames have a lower priority than itself. In this case
it would send MRP_Nack frames to notify the other node that it needs to
stop sending MRP_Test frames.
If it receives a MRP_Nack frame then it stops sending MRP_Test frames
and starts to behave as a MRC but it would continue to monitor the
MRP_Test frames send by MRM. If at a point the MRM stops to send
MRP_Test frames it would get the MRM role and start to send MRP_Test
frames.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Each MRP instance has a priority, a lower value means a higher priority.
The priority of MRP instance is stored in MRP_Test frame in this way
all the MRP nodes in the ring can see other nodes priority.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add packet traps for packets that are sampled / trapped by ACLs, so that
capable drivers could register them with devlink. Add documentation for
every added packet trap and packet trap group.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add layer 3 control packet traps such as ARP and DHCP, so that capable
device drivers could register them with devlink. Add documentation for
every added packet trap and packet trap group.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add layer 2 control packet traps such as STP and IGMP query, so that
capable device drivers could register them with devlink. Add
documentation for every added packet trap and packet trap group.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Packets that hit exceptions during layer 3 forwarding must be trapped to
the CPU for the control plane to function properly. Create a dedicated
group for them, so that user space could choose to assign a different
policer for them.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter updates for net-next
The following patchset contains Netfilter updates for net-next
to extend ctnetlink and the flowtable infrastructure:
1) Extend ctnetlink kernel side netlink dump filtering capabilities,
from Romain Bellan.
2) Generalise the flowtable hook parser to take a hook list.
3) Pass a hook list to the flowtable hook registration/unregistration.
4) Add a helper function to release the flowtable hook list.
5) Update the flowtable event notifier to pass a flowtable hook list.
6) Allow users to add new devices to an existing flowtables.
7) Allow users to remove devices to an existing flowtables.
8) Allow for registering a flowtable with no initial devices.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Drivers do not register to netdev events to set up indirect blocks
anymore. Remove __flow_indr_block_cb_register() and
__flow_indr_block_cb_unregister().
The frontends set up the callbacks through flow_indr_dev_setup_block()
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tunnel devices provide no dev->netdev_ops->ndo_setup_tc(...) interface.
The tunnel device and route control plane does not provide an obvious
way to relate tunnel and physical devices.
This patch allows drivers to register a tunnel device offload handler
for the tc and netfilter frontends through flow_indr_dev_register() and
flow_indr_dev_unregister().
The frontend calls flow_indr_dev_setup_offload() that iterates over the
list of drivers that are offering tunnel device hardware offload
support and it sets up the flow block for this tunnel device.
If the driver module is removed, the indirect flow_block ends up with a
stale callback reference. The module removal path triggers the
dev_shutdown() path to remove the qdisc and the flow_blocks for the
physical devices. However, this is not useful for tunnel devices, where
relation between the physical and the tunnel device is not explicit.
This patch introduces a cleanup callback that is invoked when the driver
module is removed to clean up the tunnel device flow_block. This patch
defines struct flow_block_indr and it uses it from flow_block_cb to
store the information that front-end requires to perform the
flow_block_cb cleanup on module removal.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This function schedules the flow teardown state and it forces a gc run.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Johan Hedberg says:
====================
pull request: bluetooth-next 2020-06-01
Here's one last bluetooth-next pull request for 5.8, which I hope can
still be accepted.
- Enabled Wide-Band Speech (WBS) support for Qualcomm wcn3991
- Multiple fixes/imprvovements to Qualcomm-based devices
- Fix GAP/SEC/SEM/BI-10-C qualfication test case
- Added support for Broadcom BCM4350C5 device
- Several other smaller fixes & improvements
Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
xdp_umem.c had overlapping changes between the 64-bit math fix
for the calculation of npgs and the removal of the zerocopy
memory type which got rid of the chunk_size_nohdr member.
The mlx5 Kconfig conflict is a case where we just take the
net-next copy of the Kconfig entry dependency as it takes on
the ESWITCH dependency by one level of indirection which is
what the 'net' conflicting change is trying to ensure.
Signed-off-by: David S. Miller <davem@davemloft.net>
Johannes Berg says:
====================
Another set of changes, including
* many 6 GHz changes, though it's not _quite_ complete
(I left out scanning for now, we're still discussing)
* allow userspace SA-query processing for operating channel
validation
* TX status for control port TX, for AP-side operation
* more per-STA/TID control options
* move to kHz for channels, for future S1G operation
* various other small changes
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Saeed Mahameed says:
====================
mlx5-cleanup-2020-05-29
Accumulated cleanup patches and sparse warning fixes for mlx5 driver.
1) sync with mlx5-next branch
2) Eli Cohen declares mpls_entry_encode() helper in mpls.h as suggested
by Jakub Kicinski and David Ahern, and use it in mlx5
3) Jesper Fixes xdp data_meta setup in mlx5
4) Many sparse and build warnings cleanup
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Move mpls_entry_encode() from net/mpls/internal.h to include/net/mpls.h
and make it available for other users. Specifically, hardware driver that
offload MPLS can benefit from that.
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Suggested-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
As of commit 98fa6271cf
("tcp: refactor setting the initial congestion window") this is called
only from tcp_input.c, so it can be static.
Signed-off-by: Florian Westphal <fw@strlen.de>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SCTP protocol allows to bind multiple address to a socket. That
feature is currently only exposed as a socket option. Add a bind_add
method struct proto that allows to bind additional addresses, and
switch the dlm code to use the method instead of going through the
socket option from kernel space.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
