ls1012a has separate input root clocks for core PLLs versus the platform
PLL, with the latter described as sysclk in the hw docs.
Accordingly, update the clock-frequency in sysclk to 125M as platform
input clock.
Signed-off-by: Scott Wood <oss@buserror.net>
Signed-off-by: Tang Yuantian <andy.tang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add "dis_rxdet_inp3_quirk" boolean property to USB3 node. This property
is used to disable rx detection in P3 PHY mode.
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Currently SD UHS-I modes were enabled by default on LS208xARDB boards,
but the new LS2088ARDB RevF board didn't support them any more since SDHC
circuit had been reworked. This patch is to disable SD UHS-I modes by default
in case of any issue on LS2088ARDB RevF
Signed-off-by: yinbo.zhu <yinbo.zhu@nxp.com>
Acked-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The at24 driver allows to register I2C EEPROM chips using different vendor
and devices, but the I2C subsystem does not take the vendor into account
when matching using the I2C table since it only has device entries.
But when matching using an OF table, both the vendor and device has to be
taken into account so the driver defines only a set of compatible strings
using the "atmel" vendor as a generic fallback for compatible I2C devices.
So add this generic fallback to the device node compatible string to make
the device to match the driver using the OF device ID table.
Signed-off-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add the DPAA 1.x FMan nodes for the ARM based platforms.
Using separate files for each port as not all ports are used on all
devices. Different numbering of ports is also possible on different
devices.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
1. Sata ecc should be disabled due to a erratum.
Provide the ecc register address for driver to use.
2. Enable dma coherence operation
Signed-off-by: Tang Yuantian <andy.tang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
LS1088AQDS consist of NOR, NAND and FPGA connected over IFC
LS1088ARDB consist of NAND and FPGA connected over IFC.
So add flash information in ifc node of device tree.
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add esdhc node for ls1088a and enable it on both RDB and QDS boards.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
There are two eSDHC controllers in LS1012A. This patch is to add
eSDHC nodes for ls1012a dts. Also enable eSDHC for RDB/QDS boards.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This patch is to enable SD UHS-I mode on LS208xRDB and eMMC HS200
mode on LS208xQDS in dts. Also, the eSDHC peripheral clock must be
used instead of platform clock to support these modes.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This patch is to enable SD UHS-I mode and eMMC HS200 mode on
LS1046ARDB in dts. Also, the eSDHC peripheral clock must be used
instead of platform clock to support these modes.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Integrated flash controller present in LS1043A and LS1046A is big endian.
So add big endian property in the devive tree.
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
LS1088A contains eight ARM v8 CortexA53 processor cores
with 32 KB L1-D cache and 32 KB L1-I cache
Features summary
Eight 32-bit / 64-bit ARM v8 Cortex-A53 CPUs
- Arranged as two clusters of four cores sharing a 1 MB L2 cache
- Speed Up to 1.5 GHz
- Support for cluster power-gating.
Cache coherent interconnect (CCI-400)
- Hardware-managed data coherency
- Up to 700 MHz
One 64-bit DDR4 SDRAM memory controller with ECC
Data path acceleration architecture 2.0 (DPAA2)
Three PCIe 3.0 controllers
One serial ATA (SATA 3.0) controller
Three high-speed USB 3.0 controllers with integrated PHY
Following levels of DTSI/DTS files have been created for the LS1088A
SoC family:
- fsl-ls1088a.dtsi:
DTS-Include file for NXP LS1088A SoC.
- fsl-ls1088a-qds.dts:
DTS file for NXP LS1088A QDS board.
- fsl-ls1088a-rdb.dts:
DTS file for NXP LS1088A RDB board
Signed-off-by: Harninder Rai <harninder.rai@nxp.com>
Signed-off-by: Ashish Kumar <ashish.kumar@nxp.com>
Signed-off-by: Raghav Dogra <raghav.dogra@nxp.com>`
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
There is a thermal monitoring unit on ls1012a soc which can
monitor and record the temperature of cores so that appropriate actions
can be taken or alarm the user when the temperature exceeds a programmed
temperature threshold.
Signed-off-by: Tang Yuantian <andy.tang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Updated sata node to add ecc register address and dma coherence
property.
Enable sata on ls1012a platforms as well.
Signed-off-by: Tang Yuantian <andy.tang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
For ls1046 sata, ecc should be disabled due to a erratum.
Provide the ecc register address for driver to use.
Signed-off-by: Tang Yuantian <yuantian.tang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
For ls1043 sata, ecc should be disabled due to a erratum.
Provide the ecc register address for driver to use.
Signed-off-by: Tang Yuantian <yuantian.tang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This patch adds the device tree support for FSL LS2088A SoC based on
ARMv8 architecture.
Following levels of DTSI/DTS files have been created for the LS2088A
SoC family:
- fsl-ls2088a.dtsi:
DTS-Include file for FSL LS2088A SoC.
- fsl-ls2088a-qds.dts:
DTS file for FSL LS2088A QDS board.
- fsl-ls2088a-rdb.dts:
DTS file for FSL LS2088A RDB board.
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Ashish Kumar <ashish.kumar@nxp.com>
Signed-off-by: Abhimanyu Saini <abhimanyu.saini@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
LS2088A and LS2080A are similar SoCs with a few differences like
ARM cores etc.
Reorganize the LS2080A device tree to move the common nodes to:
- fsl-ls208xa.dtsi
- fsl-ls208xa-rdb.dtsi
- fsl-ls208xa-qds.dtsi
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Ashish Kumar <ashish.kumar@nxp.com>
Signed-off-by: Abhimanyu Saini <abhimanyu.saini@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
LS1012A features an advanced 64-bit ARM v8 CortexA53 processor
with 32 KB of parity protected L1-I cache, 32 KB of ECC protected
L1-D cache, as well as 256 KB of ECC protected L2 cache.
Features summary
One 64-bit ARM-v8 Cortex-A53 core with the following capabilities
- Arranged as a cluster of one core supporting a 256 KB L2 cache with ECC
protection
- Speed up to 800 MHz
- Parity-protected 32 KB L1 instruction cache and 32 KB L1 data cache
- Neon SIMD engine
- ARM v8 cryptography extensions
One 16-bit DDR3L SDRAM memory controller
ARM core-link CCI-400 cache coherent interconnect
Cryptography acceleration (SEC)
One Configurable x3 SerDes
One PCI Express Gen2 controller, supporting x1 operation
One serial ATA (SATA Gen 3.0) controller
One USB 3.0/2.0 controller with integrated PHY
Following levels of DTSI/DTS files have been created for the LS1012A
SoC family:
- fsl-ls1012a.dtsi:
DTS-Include file for FSL LS1012A SoC.
- fsl-ls1012a-frdm.dts:
DTS file for FSL LS1012A FRDM board.
- fsl-ls1012a-qds.dts:
DTS file for FSL LS1012A QDS board.
- fsl-ls1012a-rdb.dts:
DTS file for FSL LS1012A RDB board.
Signed-off-by: Harninder Rai <harninder.rai@nxp.com>
Signed-off-by: Bhaskar Upadhaya <Bhaskar.Upadhaya@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
pca9547 won't probed since its status property is disabled.
while there are devices connected to it, we need remove status
property to let ds3232 and adt7461 probed correctly.
Signed-off-by: Meng Yi <meng.yi@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Pull ARM 64-bit DT updates from Arnd Bergmann:
"A couple of interesting new SoC platforms are now supported, these are
the respective DTS sources:
- Samsung Exynos5433 mobile phone platform, including an (almost)
fully supported phone reference board.
- Hisilicon Hip07 server platform and D05 board, the latest iteration
of their product line, now with 64 Cortex-A72 cores across two
sockets.
- Allwinner A64 SoC, the first 64-bit chip from their "sunxi" product
line, used in Android tablets and ultra-cheap development boards
- NXP LS1046A Communication processor, improving on the earlier
LS1043A with faster CPU cores
- Qualcomm MSM8992 (Snapdragon 808) and MSM8994 (Snapdragon 810)
mobile phone SoCs
- Early support for the Nvidia Tegra Tegra186 SoC
- Amlogic S905D is a minor variant of their existing Android consumer
product line
- Rockchip PX5 automotive platform, a close relative of their popular
rk3368 Android tablet chips
Aside from the respective evaluation platforms for the above chips,
there are only a few consumer devices and boards added this time:
- Huawei Nexus 6P (Angler) mobile phone
- LG Nexus 5x (Bullhead) mobile phone
- Nexbox A1 and A95X Android TV boxes
- Pine64 development board based on Allwinner A64
- Globalscale Marvell ESPRESSOBin community board based on Armada 3700
- Renesas "R-Car Starter Kit Pro" (M3ULCB) low-cost automotive board
For the existing platforms, we get bug fixes and new peripheral
support for Juno, Renesas, Uniphier, Amlogic, Samsung, Broadcom,
Rockchip, Berlin, and ZTE"
* tag 'armsoc-dt64' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (168 commits)
arm64: dts: fix build errors from missing dependencies
ARM64: dts: meson-gxbb: add SCPI pre-1.0 compatible
ARM64: dts: meson-gxl: Add support for Nexbox A95X
ARM64: dts: meson-gxm: Add support for the Nexbox A1
ARM: dts: artpec: add pcie support
arm64: dts: berlin4ct-dmp: add missing unit name to /memory node
arm64: dts: berlin4ct-stb: add missing unit name to /memory node
arm64: dts: berlin4ct: add missing unit name to /soc node
arm64: dts: qcom: msm8916: Add ddr support to sdhc1
arm64: dts: exynos: Enable HS400 mode for eMMC for TM2
ARM: dts: Add xo to sdhc clock node on qcom platforms
ARM64: dts: Add support for Meson GXM
dt-bindings: add rockchip RK1108 Evaluation board
arm64: dts: NS2: Add PCI PHYs
arm64: dts: NS2: enable sdio1
arm64: dts: exynos: Add the mshc_2 node for supporting T-Flash
arm64: tegra: Add NVIDIA P2771 board support
arm64: tegra: Enable PSCI on P3310
arm64: tegra: Add NVIDIA P3310 processor module support
arm64: tegra: Add GPIO controllers on Tegra186
...
Add the dts node for device configuration unit that provides
general purpose configuration and status for the device.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Scott Wood <oss@buserror.net>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Freescale arm64 device tree updates for 4.10:
- Enable Thermal Monitoring Unit (TMU) for thermal management on
LS1043A and LS2080A.
- Add support for LS1046A SoC, which has similar peripherals as
LS1043A but integrates 4 A72 cores.
- Add two LS1046A based board support: LS1046A-QDS and LS1046A-RDB.
* tag 'imx-dt64-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
arm64: dts: ls2080a: Add TMU device tree support for LS2080A
arm64: dts: ls1043a: Add TMU device tree support for LS1043A
arm64: dts: add LS1046A-QDS board support
Documentation: DT: Add entry for QorIQ LS1046A-QDS board
arm64: dts: add LS1046A-RDB board support
Documentation: DT: Add entry for QorIQ LS1046A-RDB board
arm64: dts: add QorIQ LS1046A SoC support
dt-bindings: ahci-fsl-qoriq: updated for SoC ls1046a
dt-bindings: qoriq-clock: add LS1043A/LS1046A/LS2080A compatible for clockgen
dt-bindings: i2c: adds two more nxp devices
dt-bindings: fsl: add LS1043A/LS1046A/LS2080A compatible for SCFG and DCFG
dt-bindings: fsl: Add LS1043A/LS1046A/LS2080A SoC compatible strings
Signed-off-by: Olof Johansson <olof@lixom.net>
The LS1046A QorIQ development system (QDS) board is a high-performance
computing, evaluation, development, and test platform supporting the
LS1046A SoC.
Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The LS1046A reference design board (RDB) is a high-performance computing,
evaluation, and development platform that supports the LS1046A SoC.
Signed-off-by: Mingkai Hu <Mingkai.Hu@nxp.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Both the LS1043A and LS2080A platforms are affected by the Freescale
A008585 erratum. Advertise it in their respective device trees.
Signed-off-by: Scott Wood <oss@buserror.net>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Pull libata updates from Tejun Heo:
- Write same support added
- Minor ahci MSIX irq handling updates
- Non-critical SCSI command translation fixes
- Controller specific changes
* 'for-4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
ahci: qoriq: Revert "ahci: qoriq: Disable NCQ on ls2080a SoC"
libata: remove <asm-generic/libata-portmap.h>
libata: remove unused definitions from <asm/libata-portmap.h>
pata_at91: Use PTR_ERR_OR_ZERO rather than if(IS_ERR(...)) + PTR_ERR
ata: Replace BUG() with BUG_ON().
ata: sata_mv: Replacing dma_pool_alloc and memset with a single call dma_pool_zalloc.
libata: Some drives failing on SCT Write Same
ahci: use pci_alloc_irq_vectors
libata: SCT Write Same handle ATA_DFLAG_PIO
libata: SCT Write Same / DSM Trim
libata: Add support for SCT Write Same
libata: Safely overwrite attached page in WRITE SAME xlat
ahci: also use a per-port lock for the multi-MSIX case
ARM: dts: STiH407-family: Add ports-implemented property in sata nodes
ahci: st: Add ports-implemented property in support
ahci: qoriq: enable snoopable sata read and write
ahci: qoriq: adjust sata parameter
libata-scsi: fix MODE SELECT translation for Control mode page
libata-scsi: use u8 array to store mode page copy
* dt/irq-fix:
arm64: dts: Fix broken architected timer interrupt trigger
This resolves a non-obvious conflict between a bugfix from
v4.8 and a cleanup for the exynos7 platform.
The ARM architected timer specification mandates that the interrupt
associated with each timer is level triggered (which corresponds to
the "counter >= comparator" condition).
A number of DTs are being remarkably creative, declaring the interrupt
to be edge triggered. A quick look at the TRM for the corresponding ARM
CPUs clearly shows that this is wrong, and I've corrected those.
For non-ARM designs (and in the absence of a publicly available TRM),
I've made them active low as well, which can't be completely wrong
as the GIC cannot disinguish between level low and level high.
The respective maintainers are of course welcome to prove me wrong.
While I was at it, I took the liberty to fix a couple of related issue,
such as some spurious affinity bits on ThunderX, and their complete
absence on ls1043a (both of which seem to be related to copy-pasting
from other DTs).
Acked-by: Duc Dang <dhdang@apm.com>
Acked-by: Carlo Caione <carlo@endlessm.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The 'dma-coherent' indicates that the hardware IP block can ensure
the coherency of the data transferred from/to the IP block. This
can avoid the software cache flush/invalid actions, and improve
the performance significantly.
The PCI IP block of ls2080a has this capability, so adding this
feature to improve the PCI performance.
Signed-off-by: Liu Gang <Gang.Liu@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add a default stdout-path to chosen node for ls2080a/ls1043a boards to
allow booting kernels without specifying console info in bootargs.
Signed-off-by: Stuart Yoder <stuart.yoder@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
-add missing serial aliases to ls1043a-rdb
-update ls1043a-qds boards serial aliases to use the standard duarts
instead of low power uarts
Signed-off-by: Stuart Yoder <stuart.yoder@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
By default the SATA IP on the qoriq SoCs does not generating
coherent/snoopable transactions. This patch enable it in the
sata axicc register.
In addition, the dma-coherent property must be set on the
SATA controller nodes.
Signed-off-by: Tang Yuantian <yuantian.tang@nxp.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Adds the cache nodes and next-level-cache property for the
cacheinfo to work.
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
