With the addition of TXQ stats in the per-tid statistics the struct
station_info grew significantly. This resulted in stack size warnings
due to the structure itself being above the limit for the warnings.
Add an allocation function that those who want to provide per-tid
stats should use to allocate the tid array, i.e.
struct station_info::pertid.
Cc: Toke Høiland-Jørgensen <toke@toke.dk>
Fixes: 52539ca89f ("cfg80211: Expose TXQ stats and parameters to userspace")
Signed-off-by: Arend van Spriel <aspriel@gmail.com>
[johannes: fix missing BIT() and logic by removing]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This adds support for exporting the mac80211 TXQ stats via nl80211 by
way of a nested TXQ stats attribute, as well as for configuring the
quantum and limits that were previously only changeable through debugfs.
This commit adds just the nl80211 API, a subsequent commit adds support to
mac80211 itself.
Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Average ack rssi will be given to userspace via NL80211 interface
if firmware is capable. Userspace tool ‘iw’ can process this
information and give the output as one of the fields in
‘iw dev wlanX station dump’.
Example output :
localhost ~ #iw dev wlan-5000mhz station dump Station
34:f3:9a:aa:3b:29 (on wlan-5000mhz)
inactive time: 5370 ms
rx bytes: 85321
rx packets: 576
tx bytes: 14225
tx packets: 71
tx retries: 0
tx failed: 2
beacon loss: 0
rx drop misc: 0
signal: -54 dBm
signal avg: -53 dBm
tx bitrate: 866.7 MBit/s VHT-MCS 9 80MHz short GI VHT-NSS 2
rx bitrate: 866.7 MBit/s VHT-MCS 9 80MHz short GI VHT-NSS 2
avg ack signal: -56 dBm
authorized: yes
authenticated: yes
associated: yes
preamble: short
WMM/WME: yes
MFP: no
TDLS peer: no
DTIM period: 2
beacon interval:100
short preamble: yes
short slot time:yes
connected time: 203 seconds
Main use case is to measure the signal strength of a connected station
to AP. Data packet transmit rates and bandwidth used by station can vary
a lot even if the station is at fixed location, especially if the rates
used are multi stream(2stream, 3stream) rates with different bandwidth(20/40/80 Mhz).
These multi stream rates are sensitive and station can use different transmit power
for each of the rate and bandwidth combinations. RSSI measured from these RX packets
on AP will be not stable and can vary a lot with in a short time.
Whereas 802.11 ack frames from station are sent relatively at a constant
rate (6/12/24 Mbps) with constant bandwidth(20 Mhz).
So average rssi of the ack packets is good and more accurate.
Signed-off-by: Balaji Pothunoori <bpothuno@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This will serve userspace entity to maintain its regulatory limitation.
More specifcally APs can use this data to calculate the WMM IE when
building: beacons, probe responses, assoc responses etc...
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch provide APIs to allow client drivers to support
probe deferral. On K2G SoC, devices can be probed only
after the ti_sci_pm_domains driver is probed and ready.
As drivers may get probed at different order, any driver
that depends on knav dma and qmss drivers, for example
netcp network driver, needs to defer probe until
knav devices are probed and ready to service. To do this,
add an API to query the device ready status from the knav
dma and qmss devices.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Drop unneeded elements from rt6_info struct and rearrange layout to
something more relevant for the data path.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert all code paths referencing a FIB entry from
rt6_info to fib6_info.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Last step before flipping the data type for FIB entries:
- use fib6_info_alloc to create FIB entries in ip6_route_info_create
and addrconf_dst_alloc
- use fib6_info_release in place of dst_release, ip6_rt_put and
rt6_release
- remove the dst_hold before calling __ip6_ins_rt or ip6_del_rt
- when purging routes, drop per-cpu routes
- replace inc and dec of rt6i_ref with fib6_info_hold and fib6_info_release
- use rt->from since it points to the FIB entry
- drop references to exception bucket, fib6_metrics and per-cpu from
dst entries (those are relevant for fib entries only)
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add fib6_info struct and alloc, destroy, hold and release helpers.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IPv6 FIB will only contain FIB entries with exception routes added to
the FIB entry. Once this transformation is complete, FIB lookups will
return a fib6_info with the lookup functions still returning a dst
based rt6_info. The current code uses rt6_info for both paths and
overloads the rt6_info variable usually called 'rt'.
This patch introduces a new 'f6i' variable name for the result of the FIB
lookup and keeps 'rt' as the dst based return variable. 'f6i' becomes a
fib6_info in a later patch which is why it is introduced as f6i now;
avoids the additional churn in the later patch.
In addition, remove RTF_CACHE and dst checks from fib6 add and delete
since they can not happen now and will never happen after the data
type flip.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most FIB entries can be added using memory allocated with GFP_KERNEL.
Add gfp_flags to ip6_route_add and addrconf_dst_alloc. Code paths that
can be reached from the packet path (e.g., ndisc and autoconfig) or
atomic notifiers use GFP_ATOMIC; paths from user context (adding
addresses and routes) use GFP_KERNEL.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The router discovery code has a FIB entry and wants to validate the
gateway has a neighbor entry. Refactor the existing dst_neigh_lookup
for IPv6 and create a new function that takes the gateway and device
and returns a neighbor entry. Use the new function in
ndisc_router_discovery to validate the gateway.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Continuing to wean FIB paths off of dst_entry, use a bool to hold
requests for certain dst settings. Add a helper to convert the
flags to DST flags when a FIB entry is converted to a dst_entry.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ip6_null_entry will stay a dst based return for lookups that fail to
match an entry.
Add a new fib6_null_entry which constitutes the root node and leafs
for fibs. Replace existing references to ip6_null_entry with the
new fib6_null_entry when dealing with FIBs.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add expires to rt6_info for FIB entries, and add fib6 helpers to
manage it. Data path use of dst.expires remains.
The transition is fairly straightforward: when working with fib entries,
rt->dst.expires is just rt->expires, rt6_clean_expires is replaced with
fib6_clean_expires, rt6_set_expires becomes fib6_set_expires, and
rt6_check_expired becomes fib6_check_expired, where the fib6 versions
are added by this patch.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similar to IPv4, add fib metrics to the fib struct, which at the moment
is rt6_info. Will be moved to fib6_info in a later patch. Copy metrics
into dst by reference using refcount.
To make the transition:
- add dst_metrics to rt6_info. Default to dst_default_metrics if no
metrics are passed during route add. No need for a separate pmtu
entry; it can reference the MTU slot in fib6_metrics
- ip6_convert_metrics allocates memory in the FIB entry and uses
ip_metrics_convert to copy from netlink attribute to metrics entry
- the convert metrics call is done in ip6_route_info_create simplifying
the route add path
+ fib6_commit_metrics and fib6_copy_metrics and the temporary
mx6_config are no longer needed
- add fib6_metric_set helper to change the value of a metric in the
fib entry since dst_metric_set can no longer be used
- cow_metrics for IPv6 can drop to dst_cow_metrics_generic
- rt6_dst_from_metrics_check is no longer needed
- rt6_fill_node needs the FIB entry and dst as separate arguments to
keep compatibility with existing output. Current dst address is
renamed to dest.
(to be consistent with IPv4 rt6_fill_node really should be split
into 2 functions similar to fib_dump_info and rt_fill_info)
- rt6_fill_node no longer needs the temporary metrics variable
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce fib6_nh structure and move nexthop related data from
rt6_info and rt6_info.dst to fib6_nh. References to dev, gateway or
lwtstate from a FIB lookup perspective are converted to use fib6_nh;
datapath references to dst version are left as is.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The RTN_ type for IPv6 FIB entries is currently embedded in rt6i_flags
and dst.error. Since dst is going to be removed, it can no longer be
relied on for FIB dumps so save the route type as fib6_type.
fc_type is set in current users based on the algorithm in rt6_fill_node:
- rt6i_flags contains RTF_LOCAL: fc_type = RTN_LOCAL
- rt6i_flags contains RTF_ANYCAST: fc_type = RTN_ANYCAST
- else fc_type = RTN_UNICAST
Similarly, fib6_type is set in the rt6_info templates based on the
RTF_REJECT section of rt6_fill_node converting dst.error to RTN type.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass network namespace reference into route add, delete and get
functions.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass net namespace to fib6_update_sernum. It can not be marked const
as fib6_new_sernum will change ipv6.fib6_sernum.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move logic of fib_convert_metrics into ip_metrics_convert. This allows
the code that converts netlink attributes into metrics struct to be
re-used in a later patch by IPv6.
This is mostly a code move with the following changes to variable names:
- fi->fib_net becomes net
- fc_mx and fc_mx_len are passed as inputs pulled from fib_config
- metrics array is passed as an input from fi->fib_metrics->metrics
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Like tos inherit, ttl inherit should also means inherit the inner protocol's
ttl values, which actually not implemented in vxlan yet.
But we could not treat ttl == 0 as "use the inner TTL", because that would be
used also when the "ttl" option is not specified and that would be a behavior
change, and breaking real use cases.
So add a different attribute IFLA_VXLAN_TTL_INHERIT when "ttl inherit" is
specified with ip cmd.
Reported-by: Jianlin Shi <jishi@redhat.com>
Suggested-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The statistics such as InHdrErrors should be counted on the ingress
netdev rather than on the dev from the dst, which is the egress.
Signed-off-by: Stephen Suryaputra <ssuryaextr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
BPF core gets access to __inet6_bind via ipv6_bpf_stub_impl, so it is
not invoked directly outside of af_inet6.c. Make it static and move
inet6_bind after to avoid forward declaration.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changing API ndo_xdp_xmit to take a struct xdp_frame instead of struct
xdp_buff. This brings xdp_return_frame and ndp_xdp_xmit in sync.
This builds towards changing the API further to become a bulk API,
because xdp_buff is not a queue-able object while xdp_frame is.
V4: Adjust for commit 59655a5b6c ("tuntap: XDP_TX can use native XDP")
V7: Adjust for commit d9314c474d ("i40e: add support for XDP_REDIRECT")
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changing API xdp_return_frame() to take struct xdp_frame as argument,
seems like a natural choice. But there are some subtle performance
details here that needs extra care, which is a deliberate choice.
When de-referencing xdp_frame on a remote CPU during DMA-TX
completion, result in the cache-line is change to "Shared"
state. Later when the page is reused for RX, then this xdp_frame
cache-line is written, which change the state to "Modified".
This situation already happens (naturally) for, virtio_net, tun and
cpumap as the xdp_frame pointer is the queued object. In tun and
cpumap, the ptr_ring is used for efficiently transferring cache-lines
(with pointers) between CPUs. Thus, the only option is to
de-referencing xdp_frame.
It is only the ixgbe driver that had an optimization, in which it can
avoid doing the de-reference of xdp_frame. The driver already have
TX-ring queue, which (in case of remote DMA-TX completion) have to be
transferred between CPUs anyhow. In this data area, we stored a
struct xdp_mem_info and a data pointer, which allowed us to avoid
de-referencing xdp_frame.
To compensate for this, a prefetchw is used for telling the cache
coherency protocol about our access pattern. My benchmarks show that
this prefetchw is enough to compensate the ixgbe driver.
V7: Adjust for commit d9314c474d ("i40e: add support for XDP_REDIRECT")
V8: Adjust for commit bd658dda42 ("net/mlx5e: Separate dma base address
and offset in dma_sync call")
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
New allocator type MEM_TYPE_PAGE_POOL for page_pool usage.
The registered allocator page_pool pointer is not available directly
from xdp_rxq_info, but it could be (if needed). For now, the driver
should keep separate track of the page_pool pointer, which it should
use for RX-ring page allocation.
As suggested by Saeed, to maintain a symmetric API it is the drivers
responsibility to allocate/create and free/destroy the page_pool.
Thus, after the driver have called xdp_rxq_info_unreg(), it is drivers
responsibility to free the page_pool, but with a RCU free call. This
is done easily via the page_pool helper page_pool_destroy() (which
avoids touching any driver code during the RCU callback, which could
happen after the driver have been unloaded).
V8: address issues found by kbuild test robot
- Address sparse should be static warnings
- Allow xdp.o to be compiled without page_pool.o
V9: Remove inline from .c file, compiler knows best
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Need a fast page recycle mechanism for ndo_xdp_xmit API for returning
pages on DMA-TX completion time, which have good cross CPU
performance, given DMA-TX completion time can happen on a remote CPU.
Refurbish my page_pool code, that was presented[1] at MM-summit 2016.
Adapted page_pool code to not depend the page allocator and
integration into struct page. The DMA mapping feature is kept,
even-though it will not be activated/used in this patchset.
[1] http://people.netfilter.org/hawk/presentations/MM-summit2016/generic_page_pool_mm_summit2016.pdf
V2: Adjustments requested by Tariq
- Changed page_pool_create return codes, don't return NULL, only
ERR_PTR, as this simplifies err handling in drivers.
V4: many small improvements and cleanups
- Add DOC comment section, that can be used by kernel-doc
- Improve fallback mode, to work better with refcnt based recycling
e.g. remove a WARN as pointed out by Tariq
e.g. quicker fallback if ptr_ring is empty.
V5: Fixed SPDX license as pointed out by Alexei
V6: Adjustments requested by Eric Dumazet
- Adjust ____cacheline_aligned_in_smp usage/placement
- Move rcu_head in struct page_pool
- Free pages quicker on destroy, minimize resources delayed an RCU period
- Remove code for forward/backward compat ABI interface
V8: Issues found by kbuild test robot
- Address sparse should be static warnings
- Only compile+link when a driver use/select page_pool,
mlx5 selects CONFIG_PAGE_POOL, although its first used in two patches
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the IDA infrastructure for getting a cyclic increasing ID number,
that is used for keeping track of each registered allocator per
RX-queue xdp_rxq_info. Instead of using the IDR infrastructure, which
uses a radix tree, use a dynamic rhashtable, for creating ID to
pointer lookup table, because this is faster.
The problem that is being solved here is that, the xdp_rxq_info
pointer (stored in xdp_buff) cannot be used directly, as the
guaranteed lifetime is too short. The info is needed on a
(potentially) remote CPU during DMA-TX completion time . In an
xdp_frame the xdp_mem_info is stored, when it got converted from an
xdp_buff, which is sufficient for the simple page refcnt based recycle
schemes.
For more advanced allocators there is a need to store a pointer to the
registered allocator. Thus, there is a need to guard the lifetime or
validity of the allocator pointer, which is done through this
rhashtable ID map to pointer. The removal and validity of of the
allocator and helper struct xdp_mem_allocator is guarded by RCU. The
allocator will be created by the driver, and registered with
xdp_rxq_info_reg_mem_model().
It is up-to debate who is responsible for freeing the allocator
pointer or invoking the allocator destructor function. In any case,
this must happen via RCU freeing.
Use the IDA infrastructure for getting a cyclic increasing ID number,
that is used for keeping track of each registered allocator per
RX-queue xdp_rxq_info.
V4: Per req of Jason Wang
- Use xdp_rxq_info_reg_mem_model() in all drivers implementing
XDP_REDIRECT, even-though it's not strictly necessary when
allocator==NULL for type MEM_TYPE_PAGE_SHARED (given it's zero).
V6: Per req of Alex Duyck
- Introduce rhashtable_lookup() call in later patch
V8: Address sparse should be static warnings (from kbuild test robot)
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The generic xdp_frame format, was inspired by the cpumap own internal
xdp_pkt format. It is now time to convert it over to the generic
xdp_frame format. The cpumap needs one extra field dev_rx.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The tuntap driver invented it's own driver specific way of queuing
XDP packets, by storing the xdp_buff information in the top of
the XDP frame data.
Convert it over to use the more generic xdp_frame structure. The
main problem with the in-driver method is that the xdp_rxq_info pointer
cannot be trused/used when dequeueing the frame.
V3: Remove check based on feedback from Jason
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is needed to convert drivers tuntap and virtio_net.
This is a generalization of what is done inside cpumap, which will be
converted later.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is done to prepare for the next patch, and it is also
nice to move this XDP related struct out of filter.h.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce an xdp_return_frame API, and convert over cpumap as
the first user, given it have queued XDP frame structure to leverage.
V3: Cleanup and remove C99 style comments, pointed out by Alex Duyck.
V6: Remove comment that id will be added later (Req by Alex Duyck)
V8: Rename enum mem_type to xdp_mem_type (found by kbuild test robot)
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This tracepoint was replaced by inet_sock_set_state in 563e0bb and not
used anywhere in the kernel anymore. Remove it.
Signed-off-by: Andrey Ignatov <rdna@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds missing values for the max read request size.
E.g. network driver r8169 uses a value of 4K.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some networks can make sure TCP payload can exactly fit 4KB pages,
with well chosen MSS/MTU and architectures.
Implement mmap() system call so that applications can avoid
copying data without complex splice() games.
Note that a successful mmap( X bytes) on TCP socket is consuming
bytes, as if recvmsg() has been done. (tp->copied += X)
Only PROT_READ mappings are accepted, as skb page frags
are fundamentally shared and read only.
If tcp_mmap() finds data that is not a full page, or a patch of
urgent data, -EINVAL is returned, no bytes are consumed.
Application must fallback to recvmsg() to read the problematic sequence.
mmap() wont block, regardless of socket being in blocking or
non-blocking mode. If not enough bytes are in receive queue,
mmap() would return -EAGAIN, or -EIO if socket is in a state
where no other bytes can be added into receive queue.
An application might use SO_RCVLOWAT, poll() and/or ioctl( FIONREAD)
to efficiently use mmap()
On the sender side, MSG_EOR might help to clearly separate unaligned
headers and 4K-aligned chunks if necessary.
Tested:
mlx4 (cx-3) 40Gbit NIC, with tcp_mmap program provided in following patch.
MTU set to 4168 (4096 TCP payload, 40 bytes IPv6 header, 32 bytes TCP header)
Without mmap() (tcp_mmap -s)
received 32768 MB (0 % mmap'ed) in 8.13342 s, 33.7961 Gbit,
cpu usage user:0.034 sys:3.778, 116.333 usec per MB, 63062 c-switches
received 32768 MB (0 % mmap'ed) in 8.14501 s, 33.748 Gbit,
cpu usage user:0.029 sys:3.997, 122.864 usec per MB, 61903 c-switches
received 32768 MB (0 % mmap'ed) in 8.11723 s, 33.8635 Gbit,
cpu usage user:0.048 sys:3.964, 122.437 usec per MB, 62983 c-switches
received 32768 MB (0 % mmap'ed) in 8.39189 s, 32.7552 Gbit,
cpu usage user:0.038 sys:4.181, 128.754 usec per MB, 55834 c-switches
With mmap() on receiver (tcp_mmap -s -z)
received 32768 MB (100 % mmap'ed) in 8.03083 s, 34.2278 Gbit,
cpu usage user:0.024 sys:1.466, 45.4712 usec per MB, 65479 c-switches
received 32768 MB (100 % mmap'ed) in 7.98805 s, 34.4111 Gbit,
cpu usage user:0.026 sys:1.401, 43.5486 usec per MB, 65447 c-switches
received 32768 MB (100 % mmap'ed) in 7.98377 s, 34.4296 Gbit,
cpu usage user:0.028 sys:1.452, 45.166 usec per MB, 65496 c-switches
received 32768 MB (99.9969 % mmap'ed) in 8.01838 s, 34.281 Gbit,
cpu usage user:0.02 sys:1.446, 44.7388 usec per MB, 65505 c-switches
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SO_RCVLOWAT is properly handled in tcp_poll(), so that POLLIN is only
generated when enough bytes are available in receive queue, after
David change (commit c7004482e8 "tcp: Respect SO_RCVLOWAT in tcp_poll().")
But TCP still calls sk->sk_data_ready() for each chunk added in receive
queue, meaning thread is awaken, and goes back to sleep shortly after.
Tested:
tcp_mmap test program, receiving 32768 MB of data with SO_RCVLOWAT set to 512KB
-> Should get ~2 wakeups (c-switches) per MB, regardless of how many
(tiny or big) packets were received.
High speed (mostly full size GRO packets)
received 32768 MB (100 % mmap'ed) in 8.03112 s, 34.2266 Gbit,
cpu usage user:0.037 sys:1.404, 43.9758 usec per MB, 65497 c-switches
received 32768 MB (99.9954 % mmap'ed) in 7.98453 s, 34.4263 Gbit,
cpu usage user:0.03 sys:1.422, 44.3115 usec per MB, 65485 c-switches
Low speed (sender is ratelimited and sends 1-MSS at a time, so GRO is not helping)
received 22474.5 MB (100 % mmap'ed) in 6015.35 s, 0.0313414 Gbit,
cpu usage user:0.05 sys:1.586, 72.7952 usec per MB, 44950 c-switches
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Applications might use SO_RCVLOWAT on TCP socket hoping to receive
one [E]POLLIN event only when a given amount of bytes are ready in socket
receive queue.
Problem is that receive autotuning is not aware of this constraint,
meaning sk_rcvbuf might be too small to allow all bytes to be stored.
Add a new (struct proto_ops)->set_rcvlowat method so that a protocol
can override the default setsockopt(SO_RCVLOWAT) behavior.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) In ip_gre tunnel, handle the conflict between TUNNEL_{SEQ,CSUM} and
GSO/LLTX properly. From Sabrina Dubroca.
2) Stop properly on error in lan78xx_read_otp(), from Phil Elwell.
3) Don't uncompress in slip before rstate is initialized, from Tejaswi
Tanikella.
4) When using 1.x firmware on aquantia, issue a deinit before we
hardware reset the chip, otherwise we break dirty wake WOL. From
Igor Russkikh.
5) Correct log check in vhost_vq_access_ok(), from Stefan Hajnoczi.
6) Fix ethtool -x crashes in bnxt_en, from Michael Chan.
7) Fix races in l2tp tunnel creation and duplicate tunnel detection,
from Guillaume Nault.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (22 commits)
l2tp: fix race in duplicate tunnel detection
l2tp: fix races in tunnel creation
tun: send netlink notification when the device is modified
tun: set the flags before registering the netdevice
lan78xx: Don't reset the interface on open
bnxt_en: Fix NULL pointer dereference at bnxt_free_irq().
bnxt_en: Need to include RDMA rings in bnxt_check_rings().
bnxt_en: Support max-mtu with VF-reps
bnxt_en: Ignore src port field in decap filter nodes
bnxt_en: do not allow wildcard matches for L2 flows
bnxt_en: Fix ethtool -x crash when device is down.
vhost: return bool from *_access_ok() functions
vhost: fix vhost_vq_access_ok() log check
vhost: Fix vhost_copy_to_user()
net: aquantia: oops when shutdown on already stopped device
net: aquantia: Regression on reset with 1.x firmware
cdc_ether: flag the Cinterion AHS8 modem by gemalto as WWAN
slip: Check if rstate is initialized before uncompressing
lan78xx: Avoid spurious kevent 4 "error"
lan78xx: Correctly indicate invalid OTP
...
Pull xen fixes from Juergen Gross:
"A few fixes of Xen related core code and drivers"
* tag 'for-linus-4.17-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen/pvh: Indicate XENFEAT_linux_rsdp_unrestricted to Xen
xen/acpi: off by one in read_acpi_id()
xen/acpi: upload _PSD info for non Dom0 CPUs too
x86/xen: Delay get_cpu_cap until stack canary is established
xen: xenbus_dev_frontend: Verify body of XS_TRANSACTION_END
xen: xenbus: Catch closing of non existent transactions
xen: xenbus_dev_frontend: Fix XS_TRANSACTION_END handling
Pull kdb updates from Jason Wessel:
- fix 2032 time access issues and new compiler warnings
- minor regression test cleanup
- formatting fixes for end user use of kdb
* tag 'for_linus-4.16' of git://git.kernel.org/pub/scm/linux/kernel/git/jwessel/kgdb:
kdb: use memmove instead of overlapping memcpy
kdb: use ktime_get_mono_fast_ns() instead of ktime_get_ts()
kdb: bl: don't use tab character in output
kdb: drop newline in unknown command output
kdb: make "mdr" command repeat
kdb: use __ktime_get_real_seconds instead of __current_kernel_time
misc: kgdbts: Display progress of asynchronous tests
Pull asm-generic fixes from Arnd Bergmann:
"I have one regression fix for a minor build problem after the
architecture removal series, plus a rework of the barriers in the
readl/writel functions, thanks to work by Sinan Kaya:
This started from a discussion on the linuxpcc and rdma mailing
lists[1]. To summarize, we decided that architectures are responsible
to serialize readl() and writel() accesses on a device MMIO space
relative to DMA performed by that device.
This series provides a pessimistic implementation of that behavior for
asm-generic/io.h, which is in turn used by a number of architectures
(h8300, microblaze, nios2, openrisc, s390, sparc, um, unicore32, and
xtensa). Some of those presumably need no extra barriers, or something
weaker than rmb()/wmb(), and they are advised to override the new
default for better performance.
For inb()/outb(), the same barriers are used, but architectures might
want to add another barrier to outb() here if that can guarantee
non-posted behavior (some architectures can, others cannot do that).
The readl_relaxed()/writel_relaxed() family of functions retains the
existing behavior with no extra barriers"
[1] https://lists.ozlabs.org/pipermail/linuxppc-dev/2018-March/170481.html
* tag 'asm-generic' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic:
io: change writeX_relaxed() to remove barriers
io: change readX_relaxed() to remove barriers
dts: remove cris & metag dts hard link file
io: change inX() to have their own IO barrier overrides
io: change outX() to have their own IO barrier overrides
io: define stronger ordering for the default writeX() implementation
io: define stronger ordering for the default readX() implementation
io: define several IO & PIO barrier types for the asm-generic version
Pull virtio update from Michael Tsirkin:
"This adds reporting hugepage stats to virtio-balloon"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
virtio_balloon: export hugetlb page allocation counts
Pull IOMMU updates from Joerg Roedel:
- OF_IOMMU support for the Rockchip iommu driver so that it can use
generic DT bindings
- rework of locking in the AMD IOMMU interrupt remapping code to make
it work better in RT kernels
- support for improved iotlb flushing in the AMD IOMMU driver
- support for 52-bit physical and virtual addressing in the ARM-SMMU
- various other small fixes and cleanups
* tag 'iommu-updates-v4.17' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: (53 commits)
iommu/io-pgtable-arm: Avoid warning with 32-bit phys_addr_t
iommu/rockchip: Support sharing IOMMU between masters
iommu/rockchip: Add runtime PM support
iommu/rockchip: Fix error handling in init
iommu/rockchip: Use OF_IOMMU to attach devices automatically
iommu/rockchip: Use IOMMU device for dma mapping operations
dt-bindings: iommu/rockchip: Add clock property
iommu/rockchip: Control clocks needed to access the IOMMU
iommu/rockchip: Fix TLB flush of secondary IOMMUs
iommu/rockchip: Use iopoll helpers to wait for hardware
iommu/rockchip: Fix error handling in attach
iommu/rockchip: Request irqs in rk_iommu_probe()
iommu/rockchip: Fix error handling in probe
iommu/rockchip: Prohibit unbind and remove
iommu/amd: Return proper error code in irq_remapping_alloc()
iommu/amd: Make amd_iommu_devtable_lock a spin_lock
iommu/amd: Drop the lock while allocating new irq remap table
iommu/amd: Factor out setting the remap table for a devid
iommu/amd: Use `table' instead `irt' as variable name in amd_iommu_update_ga()
iommu/amd: Remove the special case from alloc_irq_table()
...
Pull more power management updates from Rafael Wysocki:
"These include one big-ticket item which is the rework of the idle loop
in order to prevent CPUs from spending too much time in shallow idle
states. It reduces idle power on some systems by 10% or more and may
improve performance of workloads in which the idle loop overhead
matters. This has been in the works for several weeks and it has been
tested and reviewed quite thoroughly.
Also included are changes that finalize the cpufreq cleanup moving
frequency table validation from drivers to the core, a few fixes and
cleanups of cpufreq drivers, a cpuidle documentation update and a PM
QoS core update to mark the expected switch fall-throughs in it.
Specifics:
- Rework the idle loop in order to prevent CPUs from spending too
much time in shallow idle states by making it stop the scheduler
tick before putting the CPU into an idle state only if the idle
duration predicted by the idle governor is long enough.
That required the code to be reordered to invoke the idle governor
before stopping the tick, among other things (Rafael Wysocki,
Frederic Weisbecker, Arnd Bergmann).
- Add the missing description of the residency sysfs attribute to the
cpuidle documentation (Prashanth Prakash).
- Finalize the cpufreq cleanup moving frequency table validation from
drivers to the core (Viresh Kumar).
- Fix a clock leak regression in the armada-37xx cpufreq driver
(Gregory Clement).
- Fix the initialization of the CPU performance data structures for
shared policies in the CPPC cpufreq driver (Shunyong Yang).
- Clean up the ti-cpufreq, intel_pstate and CPPC cpufreq drivers a
bit (Viresh Kumar, Rafael Wysocki).
- Mark the expected switch fall-throughs in the PM QoS core (Gustavo
Silva)"
* tag 'pm-4.17-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (23 commits)
tick-sched: avoid a maybe-uninitialized warning
cpufreq: Drop cpufreq_table_validate_and_show()
cpufreq: SCMI: Don't validate the frequency table twice
cpufreq: CPPC: Initialize shared perf capabilities of CPUs
cpufreq: armada-37xx: Fix clock leak
cpufreq: CPPC: Don't set transition_latency
cpufreq: ti-cpufreq: Use builtin_platform_driver()
cpufreq: intel_pstate: Do not include debugfs.h
PM / QoS: mark expected switch fall-throughs
cpuidle: Add definition of residency to sysfs documentation
time: hrtimer: Use timerqueue_iterate_next() to get to the next timer
nohz: Avoid duplication of code related to got_idle_tick
nohz: Gather tick_sched booleans under a common flag field
cpuidle: menu: Avoid selecting shallow states with stopped tick
cpuidle: menu: Refine idle state selection for running tick
sched: idle: Select idle state before stopping the tick
time: hrtimer: Introduce hrtimer_next_event_without()
time: tick-sched: Split tick_nohz_stop_sched_tick()
cpuidle: Return nohz hint from cpuidle_select()
jiffies: Introduce USER_TICK_USEC and redefine TICK_USEC
...
Merge more updates from Andrew Morton:
- almost all of the rest of MM
- kasan updates
- lots of procfs work
- misc things
- lib/ updates
- checkpatch
- rapidio
- ipc/shm updates
- the start of willy's XArray conversion
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (140 commits)
page cache: use xa_lock
xarray: add the xa_lock to the radix_tree_root
fscache: use appropriate radix tree accessors
export __set_page_dirty
unicore32: turn flush_dcache_mmap_lock into a no-op
arm64: turn flush_dcache_mmap_lock into a no-op
mac80211_hwsim: use DEFINE_IDA
radix tree: use GFP_ZONEMASK bits of gfp_t for flags
linux/const.h: refactor _BITUL and _BITULL a bit
linux/const.h: move UL() macro to include/linux/const.h
linux/const.h: prefix include guard of uapi/linux/const.h with _UAPI
xen, mm: allow deferred page initialization for xen pv domains
elf: enforce MAP_FIXED on overlaying elf segments
fs, elf: drop MAP_FIXED usage from elf_map
mm: introduce MAP_FIXED_NOREPLACE
MAINTAINERS: update bouncing aacraid@adaptec.com addresses
fs/dcache.c: add cond_resched() in shrink_dentry_list()
include/linux/kfifo.h: fix comment
ipc/shm.c: shm_split(): remove unneeded test for NULL shm_file_data.vm_ops
kernel/sysctl.c: add kdoc comments to do_proc_do{u}intvec_minmax_conv_param
...
This results in no change in structure size on 64-bit machines as it
fits in the padding between the gfp_t and the void *. 32-bit machines
will grow the structure from 8 to 12 bytes. Almost all radix trees are
protected with (at least) a spinlock, so as they are converted from
radix trees to xarrays, the data structures will shrink again.
Initialising the spinlock requires a name for the benefit of lockdep, so
RADIX_TREE_INIT() now needs to know the name of the radix tree it's
initialising, and so do IDR_INIT() and IDA_INIT().
Also add the xa_lock() and xa_unlock() family of wrappers to make it
easier to use the lock. If we could rely on -fplan9-extensions in the
compiler, we could avoid all of this syntactic sugar, but that wasn't
added until gcc 4.6.
Link: http://lkml.kernel.org/r/20180313132639.17387-8-willy@infradead.org
Signed-off-by: Matthew Wilcox <mawilcox@microsoft.com>
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Cc: Darrick J. Wong <darrick.wong@oracle.com>
Cc: Dave Chinner <david@fromorbit.com>
Cc: Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
