The RZ/G2L SCIFA driver uses dmaengine_prep_slave_sg() to enqueue DMA
transfers and implements a timeout mechanism on RX to handle cases where
a DMA transfer does not complete. The timeout is implemented using an
hrtimer.
In the hrtimer callback, dmaengine_tx_status() is called (along with
dmaengine_pause()) to retrieve the transfer residue and handle incomplete
DMA transfers.
Add support for device_{pause, resume}() callbacks.
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Link: https://patch.msgid.link/20260316133252.240348-9-claudiu.beznea.uj@bp.renesas.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The CHCTRL register has 11 bits that can be updated by software. The
documentation for all these bits states the following:
- A read operation results in 0 being read
- Writing zero does not affect the operation
All bits in the CHCTRL register accessible by software are set and clear
bits.
The documentation for the CLREND bit of CHCTRL states:
Setting this bit to 1 can clear the END bit of the CHSTAT_n/nS register.
Also, the DMA transfer end interrupt is cleared. An attempt to read this
bit results in 0 being read.
1: Clears the END bit.
0: Does not affect the operation.
Since writing zero to any bit in this register does not affect controller
operation and reads always return zero, there is no need to perform
read-modify-write accesses to set the CLREND bit. Drop the read of the
CHCTRL register.
Also, since setting the CLREND bit does not interact with other
functionalities exposed through this register and only clears the END
interrupt, there is no need to lock around this operation. Add a comment
to document this.
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Link: https://patch.msgid.link/20260316133252.240348-4-claudiu.beznea.uj@bp.renesas.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Both rz_dmac_disable_hw() and rz_dmac_irq_handle_channel() update the
CHCTRL register. To avoid concurrency issues when configuring
functionalities exposed by this registers, take the virtual channel lock.
All other CHCTRL updates were already protected by the same lock.
Previously, rz_dmac_disable_hw() disabled and re-enabled local IRQs, before
accessing CHCTRL registers but this does not ensure race-free access.
Remove the local IRQ disable/enable code as well.
Fixes: 5000d37042 ("dmaengine: sh: Add DMAC driver for RZ/G2L SoC")
Cc: stable@vger.kernel.org
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Link: https://patch.msgid.link/20260316133252.240348-3-claudiu.beznea.uj@bp.renesas.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The driver lists (ld_free, ld_queue) are used in
rz_dmac_free_chan_resources(), rz_dmac_terminate_all(),
rz_dmac_issue_pending(), and rz_dmac_irq_handler_thread(), all under
the virtual channel lock. Take the same lock in rz_dmac_prep_slave_sg()
and rz_dmac_prep_dma_memcpy() as well to avoid concurrency issues, since
these functions also check whether the lists are empty and update or
remove list entries.
Fixes: 5000d37042 ("dmaengine: sh: Add DMAC driver for RZ/G2L SoC")
Cc: stable@vger.kernel.org
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Link: https://patch.msgid.link/20260316133252.240348-2-claudiu.beznea.uj@bp.renesas.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The Renesas RZ/T2H (R9A09G077) and RZ/N2H (R9A09G087) SoCs use a
completely different ICU unit compared to RZ/V2H, which requires a
separate implementation.
To prepare for adding support for these SoCs, add a chip-specific
structure and put a pointer to the rzv2h_icu_register_dma_req() function
in the .register_dma_req field of the chip-specific structure to allow
for other implementations. Do the same for the default request value,
RZV2H_ICU_DMAC_REQ_NO_DEFAULT, and place it into .dma_req_no_default.
While at it, factor out the logic that calls .register_dma_req() or
rz_dmac_set_dmars_register() into a separate function to remove some
code duplication.
Signed-off-by: Cosmin Tanislav <cosmin-gabriel.tanislav.xa@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20260105114445.878262-3-cosmin-gabriel.tanislav.xa@renesas.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
This was done entirely with mindless brute force, using
git grep -l '\<k[vmz]*alloc_objs*(.*, GFP_KERNEL)' |
xargs sed -i 's/\(alloc_objs*(.*\), GFP_KERNEL)/\1)/'
to convert the new alloc_obj() users that had a simple GFP_KERNEL
argument to just drop that argument.
Note that due to the extreme simplicity of the scripting, any slightly
more complex cases spread over multiple lines would not be triggered:
they definitely exist, but this covers the vast bulk of the cases, and
the resulting diff is also then easier to check automatically.
For the same reason the 'flex' versions will be done as a separate
conversion.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is the result of running the Coccinelle script from
scripts/coccinelle/api/kmalloc_objs.cocci. The script is designed to
avoid scalar types (which need careful case-by-case checking), and
instead replace kmalloc-family calls that allocate struct or union
object instances:
Single allocations: kmalloc(sizeof(TYPE), ...)
are replaced with: kmalloc_obj(TYPE, ...)
Array allocations: kmalloc_array(COUNT, sizeof(TYPE), ...)
are replaced with: kmalloc_objs(TYPE, COUNT, ...)
Flex array allocations: kmalloc(struct_size(PTR, FAM, COUNT), ...)
are replaced with: kmalloc_flex(*PTR, FAM, COUNT, ...)
(where TYPE may also be *VAR)
The resulting allocations no longer return "void *", instead returning
"TYPE *".
Signed-off-by: Kees Cook <kees@kernel.org>
Pull dmaengine updates from Vinod Koul:
"Core:
- Add Frank Li as susbstem reviewer to help with reviews
New Support:
- Mediatek support for Dimensity 6300 and 9200 controller
- Qualcomm Kaanapali and Glymur GPI DMA engine
- Synopsis DW AXI Agilex5
- Renesas RZ/V2N SoC
- Atmel microchip lan9691-dma
- Tegra ADMA tegra264
Updates:
- sg_nents_for_dma() helper use in subsystem
- pm_runtime_mark_last_busy() redundant call update for subsystem
- Residue support for xilinx AXIDMA driver
- Intel Max SGL Size Support and capabilities for DSA3.0
- AXI dma larger than 32bits address support"
* tag 'dmaengine-7.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/dmaengine: (64 commits)
dmaengine: add Frank Li as reviewer
dt-bindings: dma: qcom,gpi: Update max interrupts lines to 16
dmaengine: fsl-edma: don't explicitly disable clocks in .remove()
dmaengine: xilinx: xdma: use sg_nents_for_dma() helper
dmaengine: sh: use sg_nents_for_dma() helper
dmaengine: sa11x0: use sg_nents_for_dma() helper
dmaengine: qcom: bam_dma: use sg_nents_for_dma() helper
dmaengine: qcom: adm: use sg_nents_for_dma() helper
dmaengine: pxa-dma: use sg_nents_for_dma() helper
dmaengine: lgm: use sg_nents_for_dma() helper
dmaengine: k3dma: use sg_nents_for_dma() helper
dmaengine: dw-axi-dmac: use sg_nents_for_dma() helper
dmaengine: bcm2835-dma: use sg_nents_for_dma() helper
dmaengine: axi-dmac: use sg_nents_for_dma() helper
dmaengine: altera-msgdma: use sg_nents_for_dma() helper
scatterlist: introduce sg_nents_for_dma() helper
dmaengine: idxd: Add Max SGL Size Support for DSA3.0
dmaengine: idxd: Expose DSA3.0 capabilities through sysfs
dmaengine: sh: rz-dmac: Make channel irq local
dmaengine: pl08x: Fix comment stating the difference between PL080 and PL081
...
Clobbering an error value to be returned from shdma_tx_submit() with
a pm_runtime_put() return value is not particularly useful, especially
if the latter is 0, so stop doing that.
This will facilitate a planned change of the pm_runtime_put() return
type to void in the future.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Link: https://patch.msgid.link/9626129.rMLUfLXkoz@rafael.j.wysocki
Signed-off-by: Vinod Koul <vkoul@kernel.org>
After audio full duplex testing, playing the recorded file contains a few
playback frames from the previous time. The rz_dmac_terminate_all() does
not reset all the hardware descriptors queued previously, leading to the
wrong descriptor being picked up during the next DMA transfer. Fix the
above issue by resetting all the descriptor headers for a channel in
rz_dmac_terminate_all() as rz_dmac_lmdesc_recycle() points to the proper
descriptor header filled by the rz_dmac_prepare_descs_for_slave_sg().
Cc: stable@kernel.org
Fixes: 5000d37042 ("dmaengine: sh: Add DMAC driver for RZ/G2L SoC")
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Tested-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Link: https://patch.msgid.link/20251113195052.564338-1-biju.das.jz@bp.renesas.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The RZ DMA controller is used across multiple Renesas SoCs, not only
RZ/A1 (R7S72100) and RZ/G2L. Limiting the build to these SoCs prevents
enabling the driver on newer platforms such as RZ/V2H(P) and RZ/V2N.
Replace the ARCH_R7S72100 || ARCH_RZG2L dependency with ARCH_RENESAS so
the driver can be built for all Renesas SoCs.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Convert the Renesas R-Car DMA Controller driver from
SET_NOIRQ_SYSTEM_SLEEP_PM_OPS() and SET_RUNTIME_PM_OPS() to
NOIRQ_SYSTEM_SLEEP_PM_OPS(), RUNTIME_PM_OPS(), and pm_ptr(). This lets
us drop the check for CONFIG_PM, and reduces kernel size in case
CONFIG_PM is disabled, while increasing build coverage.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Since commit 63d00be693 ("PM: runtime: Allow unassigned
->runtime_suspend|resume callbacks"), unassigned
.runtime_{suspend,resume}() callbacks are treated the same as dummy
callbacks that just return zero.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Convert the Renesas USB-DMA Controller driver from
SET_NOIRQ_SYSTEM_SLEEP_PM_OPS() and SET_RUNTIME_PM_OPS() to
NOIRQ_SYSTEM_SLEEP_PM_OPS(), RUNTIME_PM_OPS(), and pm_ptr(). This lets
us drop the check for CONFIG_PM, and reduces kernel size in case
CONFIG_PM is disabled, while increasing build coverage.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
This patch modifies the type of setup_xref from void to int and handles
errors since the function can fail.
`setup_xref` now returns the (eventual) error from
`dmae_set_dmars`|`dmae_set_chcr`, while `shdma_tx_submit` handles the
result, removing the chunks from the queue and marking PM as idle in
case of an error.
Signed-off-by: Thomas Andreatta <thomas.andreatta2000@gmail.com>
Link: https://lore.kernel.org/r/20250827152442.90962-1-thomas.andreatta2000@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The DMAC IP found on the Renesas RZ/V2H(P) family of SoCs is
similar to the version found on the Renesas RZ/G2L family of
SoCs, but there are some differences:
* It only uses one register area
* It only uses one clock
* It only uses one reset
* Instead of using MID/IRD it uses REQ No
* It is connected to the Interrupt Control Unit (ICU)
* On the RZ/G2L there is only 1 DMAC, on the RZ/V2H(P) there are 5
Add specific support for the Renesas RZ/V2H(P) family of SoC by
tackling the aforementioned differences.
Signed-off-by: Fabrizio Castro <fabrizio.castro.jz@renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20250423143422.3747702-6-fabrizio.castro.jz@renesas.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Correctly spelled comments make it easier for the reader to understand
the code.
Replace 'enngine' with 'engine' in the comment &
replace 'trascatioin' with 'transaction' in the comment &
replace 'descripter' with 'descriptor' in the comment &
replace 'descritpor' with 'descriptor' in the comment &
replace 'rgisters' with 'registers' in the comment.
Signed-off-by: Yan Zhen <yanzhen@vivo.com>
Acked-by: Palmer Dabbelt <palmer@rivosinc.com>
Link: https://lore.kernel.org/r/20240918034114.860132-1-yanzhen@vivo.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
After commit 0edb555a65 ("platform: Make platform_driver::remove()
return void") .remove() is (again) the right callback to implement for
platform drivers.
Convert all platform drivers below drivers/dma after the previous
conversion commits apart from the wireless drivers to use .remove(),
with the eventual goal to drop struct platform_driver::remove_new(). As
.remove() and .remove_new() have the same prototypes, conversion is done
by just changing the structure member name in the driver initializer.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Link: https://lore.kernel.org/r/20241004062227.187726-2-u.kleine-koenig@baylibre.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Pull dmaengine updates from Vinod Koul:
"Unusually, more new driver and device support than updates. Couple of
new device support, AMD, Rcar, Intel and New drivers in Freescale,
Loonsoon, AMD and LPC32XX with DT conversion and mode updates etc.
New support:
- Support for AMD Versal Gen 2 DMA IP
- Rcar RZ/G3S SoC dma controller
- Support for Intel Diamond Rapids and Granite Rapids-D dma controllers
- Support for Freescale ls1021a-qdma controller
- New driver for Loongson-1 APB DMA
- New driver for AMD QDMA
- Pl08x in LPC32XX router dma driver
Updates:
- Support for dpdma cyclic dma mode
- XML conversion for marvell xor dma bindings
- Dma clocks documentation for imx dma"
* tag 'dmaengine-6.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/dmaengine: (24 commits)
dmaengine: loongson1-apb-dma: Fix the build warning caused by the size of pdev_irqname
dmaengine: Fix spelling mistakes
dmaengine: Add dma router for pl08x in LPC32XX SoC
dmaengine: fsl-edma: add edma src ID check at request channel
dmaengine: fsl-edma: change to guard(mutex) within fsl_edma3_xlate()
dmaengine: avoid non-constant format string
dmaengine: imx-dma: Remove i.MX21 support
dt-bindings: dma: fsl,imx-dma: Document the DMA clocks
dmaengine: Loongson1: Add Loongson-1 APB DMA driver
dt-bindings: dma: Add Loongson-1 APB DMA
dmaengine: zynqmp_dma: Add support for AMD Versal Gen 2 DMA IP
dt-bindings: dmaengine: zynqmp_dma: Add a new compatible string
dmaengine: idxd: Add new DSA and IAA device IDs for Diamond Rapids platform
dmaengine: idxd: Add a new DSA device ID for Granite Rapids-D platform
dmaengine: ti: k3-udma: Remove unused declarations
dmaengine: amd: qdma: Add AMD QDMA driver
dmaengine: xilinx: dpdma: Add support for cyclic dma mode
dma: ipu: Remove include/linux/dma/ipu-dma.h
dt-bindings: dma: fsl-mxs-dma: Add compatible string "fsl,imx8qxp-dma-apbh"
dt-bindings: fsl-qdma: allow compatible string fallback to fsl,ls1021a-qdma
...
A NULL dev->dma_parms indicates either a bus that is not DMA capable or
grave bug in the implementation of the bus code.
There isn't much the driver can do in terms of error handling for either
case, so just warn and continue as DMA operations will fail anyway.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org> # For MMC
We seem to have hit warnings of 'output may be truncated' which is fixed
by increasing the size of 'dev_id'
drivers/dma/sh/shdmac.c: In function ‘sh_dmae_probe’:
drivers/dma/sh/shdmac.c:541:34: error: ‘%d’ directive output may be truncated writing between 1 and 10 bytes into a region of size 9 [-Werror=format-truncation=]
541 | "sh-dmae%d.%d", pdev->id, id);
| ^~
In function ‘sh_dmae_chan_probe’,
inlined from ‘sh_dmae_probe’ at drivers/dma/sh/shdmac.c:845:9:
drivers/dma/sh/shdmac.c:541:26: note: directive argument in the range [0, 2147483647]
541 | "sh-dmae%d.%d", pdev->id, id);
| ^~~~~~~~~~~~~~
drivers/dma/sh/shdmac.c:541:26: note: directive argument in the range [0, 19]
drivers/dma/sh/shdmac.c:540:17: note: ‘snprintf’ output between 11 and 21 bytes into a destination of size 16
540 | snprintf(sh_chan->dev_id, sizeof(sh_chan->dev_id),
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
541 | "sh-dmae%d.%d", pdev->id, id);
| ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Signed-off-by: Vinod Koul <vkoul@kernel.org>
gcc points out that the fix-byte buffer might be too small:
drivers/dma/sh/usb-dmac.c: In function 'usb_dmac_probe':
drivers/dma/sh/usb-dmac.c:720:34: warning: '%u' directive writing between 1 and 10 bytes into a region of size 3 [-Wformat-overflow=]
720 | sprintf(pdev_irqname, "ch%u", index);
| ^~
In function 'usb_dmac_chan_probe',
inlined from 'usb_dmac_probe' at drivers/dma/sh/usb-dmac.c:814:9:
drivers/dma/sh/usb-dmac.c:720:31: note: directive argument in the range [0, 4294967294]
720 | sprintf(pdev_irqname, "ch%u", index);
| ^~~~~~
drivers/dma/sh/usb-dmac.c:720:9: note: 'sprintf' output between 4 and 13 bytes into a destination of size 5
720 | sprintf(pdev_irqname, "ch%u", index);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Maximum number of channels for USB-DMAC as per the driver is 1-99 so use
u8 instead of unsigned int/int for DMAC channel indexing and make the
pdev_irqname string long enough to avoid the warning.
While at it use scnprintf() instead of sprintf() to make the code more
robust.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20240110222210.193479-1-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The max channel count for RZ DMAC is 16, hence use u8 instead of unsigned
int and make the pdev_irqname string long enough to avoid the warning.
This fixes the below issue:
drivers/dma/sh/rz-dmac.c: In function ‘rz_dmac_probe’:
drivers/dma/sh/rz-dmac.c:770:34: warning: ‘%u’ directive writing between 1 and 10 bytes into a region of size 3 [-Wformat-overflow=]
770 | sprintf(pdev_irqname, "ch%u", index);
| ^~
In function ‘rz_dmac_chan_probe’,
inlined from ‘rz_dmac_probe’ at drivers/dma/sh/rz-dmac.c:910:9:
drivers/dma/sh/rz-dmac.c:770:31: note: directive argument in the range [0, 4294967294]
770 | sprintf(pdev_irqname, "ch%u", index);
| ^~~~~~
drivers/dma/sh/rz-dmac.c:770:9: note: ‘sprintf’ output between 4 and 13 bytes into a destination of size 5
770 | sprintf(pdev_irqname, "ch%u", index);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
While at it use scnprintf() instead of sprintf() to make the code
more robust.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20240110222717.193719-1-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() is renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230919133207.1400430-43-u.kleine-koenig@pengutronix.de
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() is renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230919133207.1400430-42-u.kleine-koenig@pengutronix.de
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() is renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20230919133207.1400430-41-u.kleine-koenig@pengutronix.de
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() is renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230919133207.1400430-40-u.kleine-koenig@pengutronix.de
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The DT of_device.h and of_platform.h date back to the separate
of_platform_bus_type before it as merged into the regular platform bus.
As part of that merge prepping Arm DT support 13 years ago, they
"temporarily" include each other. They also include platform_device.h
and of.h. As a result, there's a pretty much random mix of those include
files used throughout the tree. In order to detangle these headers and
replace the implicit includes with struct declarations, users need to
explicitly include the correct includes.
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20230718143138.1066177-1-robh@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
