One known problem with netlink is the fact that NLMSG_GOODSIZE is
really small on PAGE_SIZE==4096 architectures, and it is difficult
to know in advance what buffer size is used by the application.
This patch adds an automatic learning of the size.
First netlink message will still be limited to ~4K, but if user used
bigger buffers, then following messages will be able to use up to 16KB.
This speedups dump() operations by a large factor and should be safe
for legacy applications.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Thomas Graf <tgraf@suug.ch>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
For the "fsl,etsec2" compatible models the driver currently
supports 8 Tx and Rx DMA rings (aka HW queues). However, there
are only 2 pairs of Rx/Tx interrupt lines, as these controllers
are integrated in low power SoCs with 2 CPUs at most. As a result,
there are at most 2 NAPI instances that have to service multiple
Tx and Rx queues for these devices. This complicates the NAPI
polling routine having to iterate over the mutiple Rx/Tx queues
hooked to the same interrupt lines. And there's also an overhead
at HW level, as the controller needs to service all the 8 Tx rings
in a round robin manner. The combined overhead shows up for multi
parallel Tx flows transmitted by the kernel stack, when the driver
usually starts returning NETDEV_TX_BUSY leading to NETDEV WATCHDOG
Tx timeout triggering if the Tx path is congested for too long.
As an alternative, this patch makes the driver support only one
Tx/Rx DMA ring per NAPI instance (per interrupt group or pair
of Tx/Rx interrupt lines) by default. The simplified single queue
polling routine (gfar_poll_sq) will be the default napi poll routine
for the etsec2 devices too. Some adjustments needed to be made to
link the Tx/Rx HW queues with each NAPI instance (2 in this case).
The gfar_poll_sq() is already successfully used by older SQ_SG_MODE
(single interrupt group) controllers.
This patch fixes Tx timeout triggering under heavy Tx traffic load
(i.e. iperf -c -P 8) for the "fsl,etsec2" (currently the only
MQ_MG_MODE devices). There's also a significant memory footprint
reduction by supporting 2 Rx/Tx DMA rings (at most), instead of 8,
for these devices.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are some concurrency issues on devices w/ 2 CPUs related
to the handling of Rx and Tx interrupts. eTSEC has separate
interrupt lines for Rx and Tx but a single imask register
to mask these interrupts and a single NAPI instance to handle
both Rx and Tx work. As a result, the Rx and Tx ISRs are
identical, both are invoking gfar_schedule_cleanup(), however
both handlers can be entered at the same time when the Rx and
Tx interrupts are taken by different CPUs. In this case
spurrious interrupts (SPU) show up (in /proc/interrupts)
indicating a concurrency issue. Also, Tx overruns followed
by Tx timeout have been observed under heavy Tx traffic load.
To address these issues, the schedule cleanup ISR part has
been changed to handle the Rx and Tx interrupts independently.
The patch adds a separate NAPI poll routine for Tx cleanup to
be triggerred independently by the Tx confirmation interrupts
only. Existing poll functions are modified to handle only
the Rx path processing. The Tx poll routine does not need a
budget, since Tx processing doesn't consume NAPI budget, and
hence it is registered with minimum NAPI weight.
NAPI scheduling does not require locking since there are
different NAPI instances between the Rx and Tx confirmation
paths now.
So, the patch fixes the occurence of spurrious Rx/Tx interrupts.
Tx overruns also occur less frequently now.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
instead of returning the flags by reference, we can just have the
low-level primitive return those in lower bits of unsigned long,
with struct file * derived from the rest.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Our write() system call has always been atomic in the sense that you get
the expected thread-safe contiguous write, but we haven't actually
guaranteed that concurrent writes are serialized wrt f_pos accesses, so
threads (or processes) that share a file descriptor and use "write()"
concurrently would quite likely overwrite each others data.
This violates POSIX.1-2008/SUSv4 Section XSI 2.9.7 that says:
"2.9.7 Thread Interactions with Regular File Operations
All of the following functions shall be atomic with respect to each
other in the effects specified in POSIX.1-2008 when they operate on
regular files or symbolic links: [...]"
and one of the effects is the file position update.
This unprotected file position behavior is not new behavior, and nobody
has ever cared. Until now. Yongzhi Pan reported unexpected behavior to
Michael Kerrisk that was due to this.
This resolves the issue with a f_pos-specific lock that is taken by
read/write/lseek on file descriptors that may be shared across threads
or processes.
Reported-by: Yongzhi Pan <panyongzhi@gmail.com>
Reported-by: Michael Kerrisk <mtk.manpages@gmail.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
We're now blacklisting "Crucial_CT???M500SSD1" and
"Crucial_CT???M500SSD3". Also, "Micron_M500*" is blacklisted which is
about the same devices as the crucial branded ones. Let's merge the
two Crucial M500 entries and widen the match to
"Crucial_CT???M500SSD*" so that we don't have to fiddle with new
entries for similar devices.
Signed-off-by: Tejun Heo <tj@kernel.org>
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: stable@vger.kernel.org
The 88pm860 is a MFD device and the CODEC driver is using the regmap struct of
the parent device, hence automatic IO setup will not work and we need to
manually call snd_soc_codec_set_cache_io(). The issue was introduced in commit
f9ded3b2e7 ("ASoC: 88pm860x: Use regmap for I/O").
Fixes: f9ded3b2e7 ("ASoC: 88pm860x: Use regmap for I/O").
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org
The si476x is a MFD device and the CODEC driver is using the regmap struct of
the parent device, hence automatic IO setup will not work and we need to
manually call snd_soc_codec_set_cache_io(). The issue was introduced commit
d6173df35f ("ASoC: si476x: Remove custom register I/O implementation")
Fixes: d6173df35f ("ASoC: si476x: Remove custom register I/O implementation")
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org
Pull ARM SoC fixes from from Olof Johansson:
"A collection of fixes for ARM platforms. A little large due to us
missing to do one last week, but there's nothing in particular here
that is in itself large and scary.
Mostly a handful of smaller fixes all over the place. The majority is
made up of fixes for OMAP, but there are a few for others as well. In
particular, there was a decision to rename a binding for the Broadcom
pinctrl block that we need to go in before the final release since we
then treat it as ABI"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: dts: omap3-gta04: Add ti,omap36xx to compatible property to avoid problems with booting
ARM: tegra: add LED options back into tegra_defconfig
ARM: dts: omap3-igep: fix boot fail due wrong compatible match
ARM: OMAP3: Fix pinctrl interrupts for core2
pinctrl: Rename Broadcom Capri pinctrl binding
pinctrl: refer to updated dt binding string.
Update dtsi with new pinctrl compatible string
ARM: OMAP: Kill warning in CPUIDLE code with !CONFIG_SMP
ARM: OMAP2+: Add support for thumb mode on DT booted N900
ARM: OMAP2+: clock: fix clkoutx2 with CLK_SET_RATE_PARENT
ARM: OMAP4: hwmod: Fix SOFTRESET logic for OMAP4
ARM: DRA7: hwmod data: correct the sysc data for spinlock
ARM: OMAP5: PRM: Fix reboot handling
ARM: sunxi: dt: Change the touchscreen compatibles
ARM: sun7i: dt: Fix interrupt trigger types
Pull NFS client bugfixes from Trond Myklebust:
"Highlights include:
- Fix another nfs4_sequence corruptor in RELEASE_LOCKOWNER
- Fix an Oopsable delegation callback race
- Fix another bad stateid infinite loop
- Fail the data server I/O is the stateid represents a lost lock
- Fix an Oopsable sunrpc trace event"
* tag 'nfs-for-3.14-5' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
SUNRPC: Fix oops when trace sunrpc_task events in nfs client
NFSv4: Fail the truncate() if the lock/open stateid is invalid
NFSv4.1 Fail data server I/O if stateid represents a lost lock
NFSv4: Fix the return value of nfs4_select_rw_stateid
NFSv4: nfs4_stateid_is_current should return 'true' for an invalid stateid
NFS: Fix a delegation callback race
NFSv4: Fix another nfs4_sequence corruptor
Pull USB fixes from Greg KH:
"Here are 4 USB fixes for your current tree.
Two of them are reverts to hopefully resolve the nasty XHCI
regressions we have been having on some types of devices. The other
two are quirks for some Logitech video devices"
* tag 'usb-3.14-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
Revert "USBNET: ax88179_178a: enable tso if usb host supports sg dma"
Revert "xhci 1.0: Limit arbitrarily-aligned scatter gather."
usb: Make DELAY_INIT quirk wait 100ms between Get Configuration requests
usb: Add device quirk for Logitech HD Pro Webcams C920 and C930e
Pull staging driver tree fix from Greg KH:
"Here is a single staging driver fix for your tree.
It resolves an issue with arbritary writes to memory if a specific
driver is loaded"
* tag 'staging-3.15-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging/cxt1e1/linux.c: Correct arbitrary memory write in c4_ioctl()
This fixes CVE-2014-0102.
The following command sequence produces an oops:
keyctl new_session
i=`keyctl newring _ses @s`
keyctl link @s $i
The problem is that search_nested_keyrings() sees two keyrings that have
matching type and description, so keyring_compare_object() returns true.
s_n_k() then passes the key to the iterator function -
keyring_detect_cycle_iterator() - which *should* check to see whether this is
the keyring of interest, not just one with the same name.
Because assoc_array_find() will return one and only one match, I assumed that
the iterator function would only see an exact match or never be called - but
the iterator isn't only called from assoc_array_find()...
The oops looks something like this:
kernel BUG at /data/fs/linux-2.6-fscache/security/keys/keyring.c:1003!
invalid opcode: 0000 [#1] SMP
...
RIP: keyring_detect_cycle_iterator+0xe/0x1f
...
Call Trace:
search_nested_keyrings+0x76/0x2aa
__key_link_check_live_key+0x50/0x5f
key_link+0x4e/0x85
keyctl_keyring_link+0x60/0x81
SyS_keyctl+0x65/0xe4
tracesys+0xdd/0xe2
The fix is to make keyring_detect_cycle_iterator() check that the key it
has is the key it was actually looking for rather than calling BUG_ON().
A testcase has been included in the keyutils testsuite for this:
http://git.kernel.org/cgit/linux/kernel/git/dhowells/keyutils.git/commit/?id=891f3365d07f1996778ade0e3428f01878a1790b
Reported-by: Tommi Rantala <tt.rantala@gmail.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: James Morris <james.l.morris@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Ether_addr_equal_64bits is more efficient than ether_addr_equal, and
can be used when each argument is an array within a structure that
contains at least two bytes of data beyond the array, so it is safe
to use it for vlan, and make sense for fast path.
Cc: Joe Perches <joe@perches.com>
Cc: Patrick McHardy <kaber@trash.net>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According Joe's suggestion, maybe it'd be faster to add an unlikely to
the test for PCKET_OTHERHOST, so I add it and see whether the performance
could be better, although the differences is so small and negligible, but
it is hard to catch that any lower device would set the skb type to
PACKET_OTHERHOST, so most of time, I think it make sense to add unlikely
for the test.
Cc: Joe Perches <joe@perches.com>
Cc: Patrick McHardy <kaber@trash.net>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The pci shutdown handler added in:
bnx2: Add pci shutdown handler
commit 25bfb1dd4b
created a shutdown down sequence without chip reset if the device was
never brought up. This can cause the firmware to shutdown the PHY
prematurely and cause MMIO read cycles to be unresponsive. On some
systems, it may generate NMI in the bnx2's pci shutdown handler.
The fix is to tell the firmware not to shutdown the PHY if there was
no prior chip reset.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull thermal fixes from Zhang Rui:
"Specifics:
- Update the help text of INT3403 Thermal driver, which was not
friendly to users. From Zhang Rui.
- The "type" sysfs attribute of x86_pkg_temp_thermal registered
thermal zones includes an instance number, which makes the
thermal-to-hwmon bridge fails to group them all in a single hwmon
device. Fixed by Jean Delvare.
- The hwmon device registered by x86_pkg_temp_thermal driver is
redundant because the temperature value reported by
x86_pkg_temp_thermal is already reported by the coretemp driver.
Fixed by Jean Delvare.
- Fix a problem that the cooling device can not be updated properly
if it is initialized at max cooling state. From Ni Wade.
- Fix a problem that OF registered thermal zones are running without
thermal governors. From Zhang Rui.
- Commit beeb5a1e0e ("thermal: rcar-thermal: Enable driver
compilation with COMPILE_TEST") broke build on archs wihout io
memory. Thus make it depend on HAS_IOMEM to bypass build failures.
Fixed by Richard Weinberger"
* 'for-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux:
Thermal: thermal zone governor fix
Thermal: Allow first update of cooling device state
thermal,rcar_thermal: Add dependency on HAS_IOMEM
x86_pkg_temp_thermal: Fix the thermal zone type
x86_pkg_temp_thermal: Do not expose as a hwmon device
Thermal: update INT3404 thermal driver help text
Pull spi fixes from Mark Brown:
"A scattering of driver specific fixes here.
The fixes from Axel cover bitrot in apparently unmaintained drivers,
the at79 bug is fixing a glitch on /CS during initialisation of some
devices which could break some slaves and the remainder are fixes for
recently introduced bugs from the past release cycle or so"
* tag 'spi-v3.14-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: atmel: add missing spi_master_{resume,suspend} calls to PM callbacks
spi: coldfire-qspi: Fix getting correct address for *mcfqspi
spi: fsl-dspi: Fix getting correct address for master
spi: spi-ath79: fix initial GPIO CS line setup
spi: spi-imx: spi_imx_remove: do not disable disabled clocks
spi-topcliff-pch: Fix probing when DMA mode is used
spi/topcliff-pch: Fix DMA channel
Pull SCSI target fixes from Nicholas Bellinger:
"This series addresses a number of outstanding issues wrt to active I/O
shutdown using iser-target. This includes:
- Fix a long standing tpg_state bug where a tpg could be referenced
during explicit shutdown (v3.1+ stable)
- Use list_del_init for iscsi_cmd->i_conn_node so list_empty checks
work as expected (v3.10+ stable)
- Fix a isert_conn->state related hung task bug + ensure outstanding
I/O completes during session shutdown. (v3.10+ stable)
- Fix isert_conn->post_send_buf_count accounting for RDMA READ/WRITEs
(v3.10+ stable)
- Ignore FRWR completions during active I/O shutdown (v3.12+ stable)
- Fix command leakage for interrupt coalescing during active I/O
shutdown (v3.13+ stable)
Also included is another DIF emulation fix from Sagi specific to
v3.14-rc code"
* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
Target/sbc: Fix sbc_copy_prot for offset scatters
iser-target: Fix command leak for tx_desc->comp_llnode_batch
iser-target: Ignore completions for FRWRs in isert_cq_tx_work
iser-target: Fix post_send_buf_count for RDMA READ/WRITE
iscsi/iser-target: Fix isert_conn->state hung shutdown issues
iscsi/iser-target: Use list_del_init for ->i_conn_node
iscsi-target: Fix iscsit_get_tpg_from_np tpg_state bug
Revert commit 3130497f5b ("ACPI / sleep: pm_power_off needs more
sanity checks to be installed") that breaks power ACPI power off on a
lot of systems, because it checks wrong registers.
Fixes: 3130497f5b ("ACPI / sleep: pm_power_off needs more sanity checks to be installed")
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
From Tony Lindgren:
Two omap3430 vs 3630 device tree regression fixes for
issues booting 3430 based boards.
* tag 'omap-for-v3.14/fixes-dt-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: omap3-gta04: Add ti,omap36xx to compatible property to avoid problems with booting
ARM: dts: omap3-igep: fix boot fail due wrong compatible match
Signed-off-by: Olof Johansson <olof@lixom.net>
Merge 'bcm pinctrl rename' From Christin Daudt:
Rename pinctrl dt binding to restore consistency with other bcm mobile
bindings.
* tag 'bcm-for-3.14-pinctrl-reduced-rename' of git://github.com/broadcom/bcm11351:
pinctrl: Rename Broadcom Capri pinctrl binding
pinctrl: refer to updated dt binding string.
Update dtsi with new pinctrl compatible string
+ Linux 3.14-rc4
Signed-off-by: Olof Johansson <olof@lixom.net>
Allwinner fixes from Maxime Ripard:
Two fixes for device trees additions that got added in 3.14. One fixes the
interrupt types of some IPs, the other fixes up a compatible that got
introduced during 3.14
* tag 'sunxi-fixes-for-3.14' of https://github.com/mripard/linux:
ARM: sunxi: dt: Change the touchscreen compatibles
ARM: sun7i: dt: Fix interrupt trigger types
Signed-off-by: Olof Johansson <olof@lixom.net>
Resizing fq hash table allocates memory while holding qdisc spinlock,
with BH disabled.
This is definitely not good, as allocation might sleep.
We can drop the lock and get it when needed, we hold RTNL so no other
changes can happen at the same time.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Fixes: afe4fd0624 ("pkt_sched: fq: Fair Queue packet scheduler")
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates
This series contains updates to e1000e, ixgbevf and igb.
Majority of this series contains fixes and cleanups to e1000e,
most notably are:
Todd provides a fix to PTP in e1000e which adds a lock in e1000e_phc_adjfreq
to prevent concurrent changes to TIMINCA and SYSTIMH/L. Then provides an
igb fix to use ARRAY_SIZE for array size calculation.
David provides the remaining e1000e which contain:
- cleanup of pointer references that are no longer used
- fix an issue on systems with Management Engine enabled with the
ethernet cable unplugged
- fix an issue on 82579 where enabling EEE LPI sooner than one second
after link up causes link issues on some switches
- refactor the power management flows to prevent the suspend path from
being executed twice when hibernating
- refactor the runtime power management to fix interfering with the
functionality of Energy Efficient Ethernet when enabled and to fix
the device from repeatedly flip between suspend and resume with the
interface administratively downed
- enable the feature PHY Ultra Low Power Mode which is a power saving
feature that reduces the power consumption of the PHY when a cable is
not connected
- fix the ethtool offline tests for 82579 parts
- fix SHRA register access for 82579 parts which was introduced by
previous commit c3a0dce35a "e1000e: fix overrun of PHY RAR array"
Florian provides a fix for ixgbevf where skb->pkt_type was being checked
like a bitmask, but it is not a bitmask.
Fix an issue reported by Stephen Hemminger where there was a warning
about code defined but never used if IGB_HWMON is not defined.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The kbuild test robot reported:
> tree: git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace.git for-next
> head: 6f285b19d0
> commit: 6f285b19d0 [2/2] audit: Send replies in the proper network namespace.
> reproduce: make htmldocs
>
> >> Warning(kernel/audit.c:575): No description found for parameter 'request_skb'
> >> Warning(kernel/audit.c:575): Excess function parameter 'portid' description in 'audit_send_reply'
> >> Warning(kernel/auditfilter.c:1074): No description found for parameter 'request_skb'
> >> Warning(kernel/auditfilter.c:1074): Excess function parameter 'portid' description in 'audit_list_rules_s
Which was caused by my failure to update the kdoc annotations when I
updated the functions. Fix that small oversight now.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Pull cgroup fixes from Tejun Heo:
"Two cpuset locking fixes from Li. Both tagged for -stable"
* 'for-3.14-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
cpuset: fix a race condition in __cpuset_node_allowed_softwall()
cpuset: fix a locking issue in cpuset_migrate_mm()
Pull workqueue fix from Tejun Heo:
"This pull request contains a workqueue usage fix for firewire.
For quite a long time now, workqueue only treats two work items
identical iff both their addresses and callbacks match. This is to
avoid introducing false dependency through the work item being
recycled while being executed. This changes non-reentrancy guarantee
for the users of PREPARE[_DELAYED]_WORK() - if the function changes,
reentrancy isn't guaranteed against the previous instance. Firewire
depended on such nonreentrancy guarantee.
This is fixed by doing the work item multiplexing from firewire proper
while keeping the work function unchanged"
* 'for-3.14-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq:
firewire: don't use PREPARE_DELAYED_WORK
Pull firewire fixes from Stefan Richter:
"Fix a use-after-free regression since v3.4 and an initialization
regression since v3.10"
* tag 'firewire-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394:
firewire: ohci: fix probe failure with Agere/LSI controllers
firewire: net: fix use after free
Pull clk driver fix from Mike Turquette:
"Single fix for a clock driver merged in 3.14-rc1. Without this fix
the CPU frequency cannot be scaled"
* tag 'clk-fixes-for-linus' of git://git.linaro.org/people/mike.turquette/linux:
clk: shmobile: rcar-gen2: Use kick bit to allow Z clock frequency change
Pull ACPI and power management fixes from Rafael Wysocki:
- ACPI tables in some BIOSes list device resources with size equal to
0, which doesn't make sense, so we should ignore them, but instead we
try to use them and mangle things completely. Fix from Zhang Rui.
- Several models of Samsung laptops accumulate EC events when they are
in sleep states which leads to EC buffer overflows that prevent new
events from being signaled after system resume or reboot. This has
been affecting many users for quite a while and may be addressed by
clearing the EC buffer during system resume and system startup on
those machines. From Kieran Clancy.
- If the ACPI sleep control and status registers are not present (which
happens if the Hardware Reduced ACPI mode bit is set in the ACPI
tables, but also may result from BIOS bugs), we should not try to use
ACPI to power off the system and ACPI S5 should not be listed as
supported. Fix from Aubrey Li.
- There's a race condition in cpufreq_get() that leads to a kernel
crash if that function is called at a wrong time. Fix from Aaron
Plattner.
- cpufreq policy objects have to be initialized entirely before they
are first accessed by their users which isn't the case currently and
that potentially leads to various kinds of breakage that is difficult
to debug. Fix from Viresh Kumar.
- Locking is missing in __cpufreq_add_dev() which leads to a race
condition that may trigger a kernel crash. Fix from Viresh Kumar.
* tag 'pm+acpi-3.14-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI / EC: Clear stale EC events on Samsung systems
cpufreq: Initialize governor for a new policy under policy->rwsem
cpufreq: Initialize policy before making it available for others to use
cpufreq: use cpufreq_cpu_get() to avoid cpufreq_get() race conditions
ACPI / sleep: pm_power_off needs more sanity checks to be installed
ACPI / resources: ignore invalid ACPI device resources
The family in the NAT expression is basically completely useless since
we have it available during runtime anyway. Nevertheless it is used to
decide the NAT family, so at least validate it properly. As we don't
support cross-family NAT, it needs to match the family of the table the
expression exists in.
Unfortunately we can't remove it completely since we need to dump it for
userspace (*sigh*), so at least reduce the memory waste.
Additionally clean up the module init function by removing useless
temporary variables.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Since we have the context available during destruction again, we can
remove the family from the private structure.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Since we have the context available again, we can restore notifications
for destruction of anonymous sets.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
In order to fix set destruction notifications and get rid of unnecessary
members in private data structures, pass the context to expressions'
destructor functions again.
In order to do so, replace various members in the nft_rule_trans structure
by the full context.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The context argument logically comes first, and this is what every other
function dealing with contexts does.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
skb->pkt_type is not a bitmask, but contains only value at a time from
the range defined in include/uapi/linux/if_packet.h.
Checking it like if it was a bitmask of values would also cause
PACKET_OTHERHOST, PACKET_LOOPBACK and PACKET_FASTROUTE to be matched by
this check since their lower 2 bits are also set, although that does not
fix a real bug, it is still potentially confusing.
This bogus check was introduced in commit 815cccbf ("ixgbe: add setlink,
getlink support to ixgbe and ixgbevf").
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Previous commit c3a0dce35a fixed an overrun for the RAR on i218 devices.
This commit also attempted to homogenize the RAR/SHRA access for all parts
accessed by the e1000e driver. This change introduced an error for
assigning MAC addresses to guest OS's for 82579 devices.
Only RAR[0] is accessible to the driver for 82579 parts, and additional
addresses must be placed into the SHRA[L|H] registers. The rar_entry_count
was changed in the previous commit to an inaccurate value that accounted
for all RAR and SHRA registers, not just the ones usable by the driver.
This patch fixes the count to the correct value and adjusts the
e1000_rar_set_pch2lan() function to user the correct index.
Cc: John Greene <jogreene@redhat.com>
Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Changes to the rar_entry_count value require a change to the indexing
used to access the SHRA[H|L] registers when testing them with
'ethtool -t <iface> offline'
Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Valid values for InterruptThrottleRate are 10-100000, or one of
0, 1, 3, 4. '2' is not valid. This is a legacy from the branching
from the e1000 driver code that e1000e was based from.
Prior to this patch, if the e1000e driver was loaded with a forced
invalid InterruptThrottleRate of '2', then no throttle rate would be
set and no error message generated.
Now, a message will be generated that an invalid value was used and the
value for InterruptThrottleRate will be set to the default value.
Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
