asm/unaligned.h is always an include of asm-generic/unaligned.h;
might as well move that thing to linux/unaligned.h and include
that - there's nothing arch-specific in that header.
auto-generated by the following:
for i in `git grep -l -w asm/unaligned.h`; do
sed -i -e "s/asm\/unaligned.h/linux\/unaligned.h/" $i
done
for i in `git grep -l -w asm-generic/unaligned.h`; do
sed -i -e "s/asm-generic\/unaligned.h/linux\/unaligned.h/" $i
done
git mv include/asm-generic/unaligned.h include/linux/unaligned.h
git mv tools/include/asm-generic/unaligned.h tools/include/linux/unaligned.h
sed -i -e "/unaligned.h/d" include/asm-generic/Kbuild
sed -i -e "s/__ASM_GENERIC/__LINUX/" include/linux/unaligned.h tools/include/linux/unaligned.h
no_llseek had been defined to NULL two years ago, in commit 868941b144
("fs: remove no_llseek")
To quote that commit,
At -rc1 we'll need do a mechanical removal of no_llseek -
git grep -l -w no_llseek | grep -v porting.rst | while read i; do
sed -i '/\<no_llseek\>/d' $i
done
would do it.
Unfortunately, that hadn't been done. Linus, could you do that now, so
that we could finally put that thing to rest? All instances are of the
form
.llseek = no_llseek,
so it's obviously safe.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Since '__dev_queue_xmit()' should be called with interrupts enabled,
the following backtrace:
ieee80211_do_stop()
...
spin_lock_irqsave(&local->queue_stop_reason_lock, flags)
...
ieee80211_free_txskb()
ieee80211_report_used_skb()
ieee80211_report_ack_skb()
cfg80211_mgmt_tx_status_ext()
nl80211_frame_tx_status()
genlmsg_multicast_netns()
genlmsg_multicast_netns_filtered()
nlmsg_multicast_filtered()
netlink_broadcast_filtered()
do_one_broadcast()
netlink_broadcast_deliver()
__netlink_sendskb()
netlink_deliver_tap()
__netlink_deliver_tap_skb()
dev_queue_xmit()
__dev_queue_xmit() ; with IRQS disabled
...
spin_unlock_irqrestore(&local->queue_stop_reason_lock, flags)
issues the warning (as reported by syzbot reproducer):
WARNING: CPU: 2 PID: 5128 at kernel/softirq.c:362 __local_bh_enable_ip+0xc3/0x120
Fix this by implementing a two-phase skb reclamation in
'ieee80211_do_stop()', where actual work is performed
outside of a section with interrupts disabled.
Fixes: 5061b0c2b9 ("mac80211: cooperate more with network namespaces")
Reported-by: syzbot+1a3986bbd3169c307819@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=1a3986bbd3169c307819
Signed-off-by: Dmitry Antipov <dmantipov@yandex.ru>
Link: https://patch.msgid.link/20240906123151.351647-1-dmantipov@yandex.ru
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently DFS works under assumption there could be only one channel
context in the hardware. Hence, drivers just calls the function
ieee80211_radar_detected() passing the hardware structure. However, with
MLO, this obviously will not work since number of channel contexts will be
more than one and hence drivers would need to pass the channel information
as well on which the radar is detected.
Also, when radar is detected in one of the links, other link's CAC should
not be cancelled.
Hence, in order to support DFS with MLO, do the following changes -
* Add channel context conf pointer as an argument to the function
ieee80211_radar_detected(). During MLO, drivers would have to pass on
which channel context conf radar is detected. Otherwise, drivers could
just pass NULL.
* ieee80211_radar_detected() will iterate over all channel contexts
present and
* if channel context conf is passed, only mark that as radar
detected
* if NULL is passed, then mark all channel contexts as radar
detected
* Then as usual, schedule the radar detected work.
* In the worker, go over all the contexts again and for all such context
which is marked with radar detected, cancel the ongoing CAC by calling
ieee80211_dfs_cac_cancel() and then notify cfg80211 via
cfg80211_radar_event().
* To cancel the CAC, pass the channel context as well where radar is
detected to ieee80211_dfs_cac_cancel(). This ensures that CAC is
canceled only on the links using the provided context, leaving other
links unaffected.
This would also help in scenarios where there is split phy 5 GHz radio,
which is capable of DFS channels in both lower and upper band. In this
case, simultaneous radars can be detected.
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Link: https://patch.msgid.link/20240906064426.2101315-9-quic_adisi@quicinc.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently, during starting a radar detection, no link id information is
parsed and passed down. In order to support starting radar detection
during Multi Link Operation, it is required to pass link id as well.
Add changes to first parse and then pass link id in the start radar
detection path.
Additionally, update notification APIs to allow drivers/mac80211 to
pass the link ID.
However, everything is handled at link 0 only until all API's are ready to
handle it per link.
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Link: https://patch.msgid.link/20240906064426.2101315-6-quic_adisi@quicinc.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
A few members related to DFS handling are currently under per wireless
device data structure. However, in order to support DFS with MLO, there is
a need to have them on a per-link manner.
Hence, as a preliminary step, move members cac_started, cac_start_time
and cac_time_ms to be on a per-link basis.
Since currently, link ID is not known at all places, use default value of
0 for now.
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Link: https://patch.msgid.link/20240906064426.2101315-5-quic_adisi@quicinc.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This reverts commit ce9e660ef3 ("wifi: mac80211: move radar detect work to sdata").
To enable radar detection with MLO, it’s essential to handle it on a
per-link basis. This is because when using MLO, multiple links may already
be active and beaconing. In this scenario, another link should be able to
initiate a radar detection. Also, if underlying links are associated with
different hardware devices but grouped together for MLO, they could
potentially start radar detection simultaneously. Therefore, it makes
sense to manage radar detection settings separately for each link by moving
them back to a per-link data structure.
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Link: https://patch.msgid.link/20240906064426.2101315-2-quic_adisi@quicinc.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When we had a comeback, we will never use the default timeout values
again because comeback is never cleared.
Clear comeback if we send another association request which will allow
to start a default timer after Tx status.
The problem was seen with iwlwifi where the tx_status on the association
request is handled before the association response frame (which is the
usual case).
1) Tx assoc request 1/3
2) Rx assoc response (comeback, timeout = 1 second)
3) wait 1 second
4) Tx assoc request 2/3
5) Set timer to IEEE80211_ASSOC_TIMEOUT_LONG = 500ms (1 second after
round_up)
6) tx_status on frame sent in 4) is ignored because comeback is still
true
7) AP does not reply with assoc response
8) wait 1s <= This is where the bug is felt
9) Tx assoc request 3/3
With this fix, in step 6 we will reset the timer to
IEEE80211_ASSOC_TIMEOUT_SHORT = 100ms and we will wait only 100ms in
step 8.
Fixes: b133fdf07d ("wifi: mac80211: Skip association timeout update after comeback rejection")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Link: https://patch.msgid.link/20240808085916.23519-1-emmanuel.grumbach@intel.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Drivers may at times want to iterate their stations with a function
which requires some non-atomic operations.
ieee80211_iterate_stations_mtx() introduces an API to iterate stations
while holding that wiphy's mutex. This allows the iterating function to
do non-atomic operations safely.
Signed-off-by: Rory Little <rory@candelatech.com>
Link: https://patch.msgid.link/20240806004024.2014080-2-rory@candelatech.com
[unify internal list iteration functions]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Introduce 'ieee80211_mgmt_ba()' to avoid code duplication between
'ieee80211_send_addba_resp()', 'ieee80211_send_addba_request()',
and 'ieee80211_send_delba()', ensure that all related addresses
are '__aligned(2)', and prefer convenient 'ether_addr_copy()'
over generic 'memcpy()'. No functional changes expected.
Signed-off-by: Dmitry Antipov <dmantipov@yandex.ru>
Link: https://patch.msgid.link/20240725090925.6022-1-dmantipov@yandex.ru
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In commit 0d9c2beed1 ("wifi: mac80211: fix monitor channel
with chanctx emulation") I changed mac80211 to always have an
internal monitor_sdata to have something to have the chanctx
bound to.
However, if the driver didn't also have the WANT_MONITOR flag
this would cause mac80211 to allocate it without telling the
driver (which was intentional) but also use it for later APIs
to the driver without it ever having known about it which was
_not_ intentional.
Check through the code and only use the monitor_sdata in the
relevant places (TX, MU-MIMO follow settings, TX power, and
interface iteration) when the WANT_MONITOR flag is set.
Cc: stable@vger.kernel.org
Fixes: 0d9c2beed1 ("wifi: mac80211: fix monitor channel with chanctx emulation")
Reported-by: ZeroBeat <ZeroBeat@gmx.de>
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=219086
Tested-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://patch.msgid.link/20240725184836.25d334157a8e.I02574086da2c5cf0e18264ce5807db6f14ffd9c0@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Chanctx emulation didn't info IEEE80211_CONF_CHANGE_CHANNEL to drivers
during ieee80211_restart_hw (ieee80211_emulate_add_chanctx). It caused
non-chanctx drivers to not stand on the correct channel after recovery.
RX then behaved abnormally. Finally, disconnection/reconnection occurred.
So, set IEEE80211_CONF_CHANGE_CHANNEL when in_reconfig.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Link: https://patch.msgid.link/20240709073531.30565-1-kevin_yang@realtek.com
Cc: stable@vger.kernel.org
Fixes: 0a44dfc070 ("wifi: mac80211: simplify non-chanctx drivers")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This flag is annoying because it puts a lot of logic into mac80211
that could just as well be in the driver (only iwlmvm uses it) and
the implementation is also broken for MLO.
Remove the flag in favour of calling drv_mgd_prepare_tx() without
any conditions even for the deauth-while-assoc case. The drivers
that implement it can take the appropriate actions, which for the
only user of DEAUTH_NEED_MGD_TX_PREP (iwlmvm) is a bit more tricky
than the implementation in mac80211 is anyway, and all others have
no need and can just exit if info->was_assoc is set.
Reviewed-by: Miriam Rachel Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20240627132527.94924bcc9c9e.I328a219e45f2e2724cd52e75bb9feee3bf21a463@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Cross-merge networking fixes after downstream PR.
No conflicts.
Adjacent changes:
e3f02f32a0 ("ionic: fix kernel panic due to multi-buffer handling")
d9c0420999 ("ionic: Mark error paths in the data path as unlikely")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When updating a channel context, the code can apply wider
bandwidth TDLS STA channel definitions to each and every
channel context used by the device, an approach that will
surely lead to problems if there is ever more than one.
Restrict the wider BW TDLS STA consideration to only TDLS
STAs that are actually related to links using the channel
context being updated.
Fixes: 0fabfaafec ("mac80211: upgrade BW of TDLS peers when possible")
Reviewed-by: Miriam Rachel Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20240612143707.1ad989acecde.I5c75c94d95c3f4ea84f8ff4253189f4b13bad5c3@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Make ieee80211_chan_bw_change() able to use the reserved chanreq
(really the chandef part of it) for the calculations, so it can
be used _without_ applying the changes first. Remove the comment
that indicates this is required, since it no longer is. However,
this capability only gets used later.
Also, this is not ideal, we really should not different so much
between reserved and non-reserved usage, to simplify. That's a
further cleanup later though.
Reviewed-by: Miriam Rachel Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20240612143418.1a08cf83b8cb.Ie567bb272eb25ce487651088f13ad041f549651c@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
