During VSI reconfiguration filters and VSI config which is set in
ice_vf_init_host_cfg() are lost. Recall the host configuration function
to restore them.
Without this config VF on which MSI-X amount was changed might had a
connection problems.
Fixes: 4d38cb44bd ("ice: manage VFs MSI-X using resource tracking")
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
ice_qp_dis() currently does things in very mixed way. Tx is stopped
before disabling IRQ on related queue vector, then it takes care of
disabling Rx and finally NAPI is disabled.
Let us start with disabling IRQs in the first place followed by turning
off NAPI. Then it is safe to handle queues.
One subtle change on top of that is that even though ice_qp_ena() looks
more sane, clear ICE_CFG_BUSY as the last thing there.
Fixes: 2d4238f556 ("ice: Add support for AF_XDP")
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Chandan Kumar Rout <chandanx.rout@intel.com> (A Contingent Worker at Intel)
Acked-by: Magnus Karlsson <magnus.karlsson@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Disable NAPI before shutting down queues that this particular NAPI
contains so that the order of actions in i40e_queue_pair_disable()
mirrors what we do in i40e_queue_pair_enable().
Fixes: 123cecd427 ("i40e: added queue pair disable/enable functions")
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Chandan Kumar Rout <chandanx.rout@intel.com> (A Contingent Worker at Intel)
Acked-by: Magnus Karlsson <magnus.karlsson@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Currently routines that are supposed to toggle state of ring pair do not
take care of associated interrupt with queue vector that these rings
belong to. This causes funky issues such as dead interface due to irq
misconfiguration, as per Pavel's report from Closes: tag.
Add a function responsible for disabling single IRQ in EIMC register and
call this as a very first thing when disabling ring pair during xsk_pool
setup. For enable let's reuse ixgbe_irq_enable_queues(). Besides this,
disable/enable NAPI as first/last thing when dealing with closing or
opening ring pair that xsk_pool is being configured on.
Reported-by: Pavel Vazharov <pavel@x3me.net>
Closes: https://lore.kernel.org/netdev/CAJEV1ijxNyPTwASJER1bcZzS9nMoZJqfR86nu_3jFFVXzZQ4NA@mail.gmail.com/
Fixes: 024aa5800f ("ixgbe: added Rx/Tx ring disable/enable functions")
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Acked-by: Magnus Karlsson <magnus.karlsson@intel.com>
Tested-by: Chandan Kumar Rout <chandanx.rout@intel.com> (A Contingent Worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
It is now possible to disable BQL, but that causes the cpsw driver to break:
drivers/net/ethernet/ti/am65-cpsw-nuss.c:297:28: error: no member named 'dql' in 'struct netdev_queue'
297 | dql_avail(&netif_txq->dql),
There is already a helper function in net/sch_generic.h that could
be used to help here. Move its implementation into the common
linux/netdevice.h along with the other bql interfaces and change
both users over to the new interface.
Fixes: ea7f3cfaa5 ("net: bql: allow the config to be disabled")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current driver has some asymmetry in the runtime PM calls. On lan78xx_open()
it will call usb_autopm_get() and unconditionally usb_autopm_put(). And
on lan78xx_stop() it will call only usb_autopm_put(). So far, it was
working only because this driver do not activate autosuspend by default,
so it was visible only by warning "Runtime PM usage count underflow!".
Since, with current driver, we can't use runtime PM with active link,
execute lan78xx_open()->usb_autopm_put() only in error case. Otherwise,
keep ref counting high as long as interface is open.
Fixes: 55d7de9de6 ("Microchip's LAN7800 family USB 2/3 to 10/100/1000 Ethernet device driver")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently when suspending driver and stopping workqueue it is checked whether
workqueue is not NULL and if so, it is destroyed.
Function destroy_workqueue() does drain queue and does clear variable, but
it does not set workqueue variable to NULL. This can cause kernel/module
panic if code attempts to clear workqueue that was not initialized.
This scenario is possible when resuming suspended driver in stmmac_resume(),
because there is no handling for failed stmmac_hw_setup(),
which can fail and return if DMA engine has failed to initialize,
and workqueue is initialized after DMA engine.
Should DMA engine fail to initialize, resume will proceed normally,
but interface won't work and TX queue will eventually timeout,
causing 'Reset adapter' error.
This then does destroy workqueue during reset process.
And since workqueue is initialized after DMA engine and can be skipped,
it will cause kernel/module panic.
To secure against this possible crash, set workqueue variable to NULL when
destroying workqueue.
Log/backtrace from crash goes as follows:
[88.031977]------------[ cut here ]------------
[88.031985]NETDEV WATCHDOG: eth0 (sxgmac): transmit queue 1 timed out
[88.032017]WARNING: CPU: 0 PID: 0 at net/sched/sch_generic.c:477 dev_watchdog+0x390/0x398
<Skipping backtrace for watchdog timeout>
[88.032251]---[ end trace e70de432e4d5c2c0 ]---
[88.032282]sxgmac 16d88000.ethernet eth0: Reset adapter.
[88.036359]------------[ cut here ]------------
[88.036519]Call trace:
[88.036523] flush_workqueue+0x3e4/0x430
[88.036528] drain_workqueue+0xc4/0x160
[88.036533] destroy_workqueue+0x40/0x270
[88.036537] stmmac_fpe_stop_wq+0x4c/0x70
[88.036541] stmmac_release+0x278/0x280
[88.036546] __dev_close_many+0xcc/0x158
[88.036551] dev_close_many+0xbc/0x190
[88.036555] dev_close.part.0+0x70/0xc0
[88.036560] dev_close+0x24/0x30
[88.036564] stmmac_service_task+0x110/0x140
[88.036569] process_one_work+0x1d8/0x4a0
[88.036573] worker_thread+0x54/0x408
[88.036578] kthread+0x164/0x170
[88.036583] ret_from_fork+0x10/0x20
[88.036588]---[ end trace e70de432e4d5c2c1 ]---
[88.036597]Unable to handle kernel NULL pointer dereference at virtual address 0000000000000004
Fixes: 5a5586112b ("net: stmmac: support FPE link partner hand-shaking procedure")
Signed-off-by: Jakub Raczynski <j.raczynski@samsung.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Kalle Valo says:
====================
wireless fixes for v6.8-rc7
Few remaining fixes, hopefully the last wireless pull request to v6.8.
Two fixes to the stack and two to iwlwifi but no high priority fixes
this time.
* tag 'wireless-2024-02-27' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless:
wifi: mac80211: only call drv_sta_rc_update for uploaded stations
MAINTAINERS: wifi: Add N: ath1*k entries to match .yaml files
MAINTAINERS: wifi: update Jeff Johnson e-mail address
wifi: iwlwifi: mvm: fix the TXF mapping for BZ devices
wifi: iwlwifi: mvm: ensure offloading TID queue exists
wifi: nl80211: reject iftype change with mesh ID change
====================
Link: https://lore.kernel.org/r/20240227135751.C5EC6C43390@smtp.kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently using plain XDP/ZC sockets on stmmac results in a kernel crash:
|[ 255.822584] Unable to handle kernel NULL pointer dereference at virtual address 0000000000000000
|[...]
|[ 255.822764] Call trace:
|[ 255.822766] stmmac_tx_clean.constprop.0+0x848/0xc38
The program counter indicates xsk_tx_metadata_complete(). It works on
compl->tx_timestamp, which is not set by xsk_tx_metadata_to_compl() due to
missing meta data. Therefore, call xsk_tx_metadata_complete() only when
meta data is actually used.
Tested on imx93 without XDP, with XDP and with XDP/ZC.
Fixes: 1347b41931 ("net: stmmac: Add Tx HWTS support to XDP ZC")
Suggested-by: Serge Semin <fancer.lancer@gmail.com>
Tested-by: Serge Semin <fancer.lancer@gmail.com>
Link: https://lore.kernel.org/netdev/87r0h7wg8u.fsf@kurt.kurt.home/
Acked-by: Stanislav Fomichev <sdf@google.com>
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Link: https://lore.kernel.org/r/20240222-stmmac_xdp-v2-1-4beee3a037e4@linutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The MII code does not check the return value of mdio_read (among
others), and therefore no error code should be sent. A previous fix to
the use of an uninitialized variable propagates negative error codes,
that might lead to wrong operations by the MII library.
An example of such issues is the use of mii_nway_restart by the dm9601
driver. The mii_nway_restart function does not check the value returned
by mdio_read, which in this case might be a negative number which could
contain the exact bit the function checks (BMCR_ANENABLE = 0x1000).
Return zero in case of error, as it is common practice in users of
mdio_read to avoid wrong uses of the return value.
Fixes: 8f8abb863f ("net: usb: dm9601: fix uninitialized variable use in dm9601_mdio_read")
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Peter Korsgaard <peter@korsgaard.com>
Link: https://lore.kernel.org/r/20240225-dm9601_ret_err-v1-1-02c1d959ea59@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When rebuilding the lif after an FLR, be sure to restore the
current netdev features, not do the usual first time feature
init. This prevents losing user changes to things like TSO
or vlan tagging states.
Fixes: 45b84188a0 ("ionic: keep filters across FLR")
Reviewed-by: Brett Creeley <brett.creeley@amd.com>
Signed-off-by: Shannon Nelson <shannon.nelson@amd.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Since we now have potential cases of NULL cmd_regs and info_regs
during a reset recovery, and left NULL if a reset recovery has
failed, we need to check that they exist before we use them.
Most of the cases were covered in the original patch where we
verify before doing the ioreadb() for health or cmd status.
However, we need to protect a few uses of io mem that could
be hit in error recovery or asynchronous threads calls as well
(e.g. ethtool or devlink handlers).
Fixes: 219e183272 ("ionic: no fw read when PCI reset failed")
Reviewed-by: Brett Creeley <brett.creeley@amd.com>
Signed-off-by: Shannon Nelson <shannon.nelson@amd.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
AER recovery handler can trigger a PCI Reset after tearing
down the device setup in the error detection handler. The PCI
Reset handler will also attempt to tear down the device setup,
and this second tear down needs to know that it doesn't need
to call pci_release_regions() a second time. We can clear
num_bars on tear down and use that to decide later if we need
to clear the resources. This prevents a harmless but disturbing
warning message
resource: Trying to free nonexistent resource <0xXXXXXXXXXX-0xXXXXXXXXXX>
Fixes: c3a910e1c4 ("ionic: fill out pci error handlers")
Reviewed-by: Brett Creeley <brett.creeley@amd.com>
Signed-off-by: Shannon Nelson <shannon.nelson@amd.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Same as LAN7800, LAN7850 can be used without EEPROM. If EEPROM is not
present or not flashed, LAN7850 will fail to sync the speed detected by the PHY
with the MAC. In case link speed is 100Mbit, it will accidentally work,
otherwise no data can be transferred.
Better way would be to implement link_up callback, or set auto speed
configuration unconditionally. But this changes would be more intrusive.
So, for now, set it only if no EEPROM is found.
Fixes: e69647a19c ("lan78xx: Set ASD in MAC_CR when EEE is enabled.")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://lore.kernel.org/r/20240222123839.2816561-1-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
veth sets NETIF_F_GRO automatically when XDP is enabled,
because both features use the same NAPI machinery.
The logic to clear NETIF_F_GRO sits in veth_disable_xdp() which
is called both on ndo_stop and when XDP is turned off.
To avoid the flag from being cleared when the device is brought
down, the clearing is skipped when IFF_UP is not set.
Bringing the device down should indeed not modify its features.
Unfortunately, this means that clearing is also skipped when
XDP is disabled _while_ the device is down. And there's nothing
on the open path to bring the device features back into sync.
IOW if user enables XDP, disables it and then brings the device
up we'll end up with a stray GRO flag set but no NAPI instances.
We don't depend on the GRO flag on the datapath, so the datapath
won't crash. We will crash (or hang), however, next time features
are sync'ed (either by user via ethtool or peer changing its config).
The GRO flag will go away, and veth will try to disable the NAPIs.
But the open path never created them since XDP was off, the GRO flag
was a stray. If NAPI was initialized before we'll hang in napi_disable().
If it never was we'll crash trying to stop uninitialized hrtimer.
Move the GRO flag updates to the XDP enable / disable paths,
instead of mixing them with the ndo_open / ndo_close paths.
Fixes: d3256efd8e ("veth: allow enabling NAPI even without XDP")
Reported-by: Thomas Gleixner <tglx@linutronix.de>
Reported-by: syzbot+039399a9b96297ddedca@syzkaller.appspotmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 3ce4f9c3fb ("net/ps3_gelic_net: Add gelic_descr structures") of
6.8-rc1 had a copy-and-paste error where the pointer that holds the
allocated SKB (struct gelic_descr.skb) was set to NULL after the SKB was
allocated. This resulted in a kernel panic when the SKB pointer was
accessed.
This fix moves the initialization of the gelic_descr to before the SKB
is allocated.
Reported-by: sambat goson <sombat3960@gmail.com>
Fixes: 3ce4f9c3fb ("net/ps3_gelic_net: Add gelic_descr structures")
Signed-off-by: Geoff Levand <geoff@infradead.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 5d93cfcf73 ("net: dpaa: Convert to phylink"), we support
the "10gbase-r" phy-mode through a driver-based conversion of "xgmii",
but we still don't actually support it when the device tree specifies
"10gbase-r" proper.
This is because boards such as LS1046A-RDB do not define pcs-handle-names
(for whatever reason) in the ethernet@f0000 device tree node, and the
code enters through this code path:
err = of_property_match_string(mac_node, "pcs-handle-names", "xfi");
// code takes neither branch and falls through
if (err >= 0) {
(...)
} else if (err != -EINVAL && err != -ENODATA) {
goto _return_fm_mac_free;
}
(...)
/* For compatibility, if pcs-handle-names is missing, we assume this
* phy is the first one in pcsphy-handle
*/
err = of_property_match_string(mac_node, "pcs-handle-names", "sgmii");
if (err == -EINVAL || err == -ENODATA)
pcs = memac_pcs_create(mac_node, 0); // code takes this branch
else if (err < 0)
goto _return_fm_mac_free;
else
pcs = memac_pcs_create(mac_node, err);
// A default PCS is created and saved in "pcs"
// This determination fails and mistakenly saves the default PCS
// memac->sgmii_pcs instead of memac->xfi_pcs, because at this
// stage, mac_dev->phy_if == PHY_INTERFACE_MODE_10GBASER.
if (err && mac_dev->phy_if == PHY_INTERFACE_MODE_XGMII)
memac->xfi_pcs = pcs;
else
memac->sgmii_pcs = pcs;
In other words, in the absence of pcs-handle-names, the default
xfi_pcs assignment logic only works when in the device tree we have
PHY_INTERFACE_MODE_XGMII.
By reversing the order between the fallback xfi_pcs assignment and the
"xgmii" overwrite with "10gbase-r", we are able to support both values
in the device tree, with identical behavior.
Currently, it is impossible to make the s/xgmii/10gbase-r/ device tree
conversion, because it would break forward compatibility (new device
tree with old kernel). The only way to modify existing device trees to
phy-interface-mode = "10gbase-r" is to fix stable kernels to accept this
value and handle it properly.
One reason why the conversion is desirable is because with pre-phylink
kernels, the Aquantia PHY driver used to warn about the improper use
of PHY_INTERFACE_MODE_XGMII [1]. It is best to have a single (latest)
device tree that works with all supported stable kernel versions.
Note that the blamed commit does not constitute a regression per se.
Older stable kernels like 6.1 still do not work with "10gbase-r", but
for a different reason. That is a battle for another time.
[1] https://lore.kernel.org/netdev/20240214-ls1046-dts-use-10gbase-r-v1-1-8c2d68547393@concurrent-rt.com/
Fixes: 5d93cfcf73 ("net: dpaa: Convert to phylink")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Sean Anderson <sean.anderson@seco.com>
Acked-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2024-02-20 (ice)
This series contains updates to ice driver only.
Yochai sets parent device to properly reflect connection state between
source DPLL and output pin.
Arkadiusz fixes additional issues related to DPLL; proper reporting of
phase_adjust value and preventing use/access of data while resetting.
Amritha resolves ASSERT_RTNL() being triggered on certain reset/rebuild
flows.
* '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
ice: Fix ASSERT_RTNL() warning during certain scenarios
ice: fix pin phase adjust updates on PF reset
ice: fix dpll periodic work data updates on PF reset
ice: fix dpll and dpll_pin data access on PF reset
ice: fix dpll input pin phase_adjust value updates
ice: fix connection state of DPLL and out pin
====================
Reviewed-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Link: https://lore.kernel.org/r/20240220214444.1039759-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Commit bb726b753f ("net: phy: realtek: add support for
RTL8211F(D)(I)-VD-CG") extended support of the driver from the existing
support for RTL8211F(D)(I)-CG PHY to the newer RTL8211F(D)(I)-VD-CG PHY.
While that commit indicated that the RTL8211F_PHYCR2 register is not
supported by the "VD-CG" PHY model and therefore updated the corresponding
section in rtl8211f_config_init() to be invoked conditionally, the call to
"genphy_soft_reset()" was left as-is, when it should have also been invoked
conditionally. This is because the call to "genphy_soft_reset()" was first
introduced by the commit 0a4355c2b7 ("net: phy: realtek: add dt property
to disable CLKOUT clock") since the RTL8211F guide indicates that a PHY
reset should be issued after setting bits in the PHYCR2 register.
As the PHYCR2 register is not applicable to the "VD-CG" PHY model, fix the
rtl8211f_config_init() function by invoking "genphy_soft_reset()"
conditionally based on the presence of the "PHYCR2" register.
Fixes: bb726b753f ("net: phy: realtek: add support for RTL8211F(D)(I)-VD-CG")
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240220070007.968762-1-s-vadapalli@ti.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Both registers used when doing manual injection or fdma injection are
shared between all the net devices of the switch. It was noticed that
when having two process which each of them trying to inject frames on
different ethernet ports, that the HW started to behave strange, by
sending out more frames then expected. When doing fdma injection it is
required to set the frame in the DCB and then make sure that the next
pointer of the last DCB is invalid. But because there is no locks for
this, then easily this pointer between the DCB can be broken and then it
would create a loop of DCBs. And that means that the HW will
continuously transmit these frames in a loop. Until the SW will break
this loop.
Therefore to fix this issue, add a spin lock for when accessing the
registers for manual or fdma injection.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Daniel Machon <daniel.machon@microchip.com>
Fixes: f3cad2611a ("net: sparx5: add hostmode with phylink support")
Link: https://lore.kernel.org/r/20240219080043.1561014-1-horatiu.vultur@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fix EST offset for dwmac 5.10.
Currently configuring Qbv doesn't work as expected. The schedule is
configured, but never confirmed:
|[ 128.250219] imx-dwmac 428a0000.ethernet eth1: configured EST
The reason seems to be the refactoring of the EST code which set the wrong
EST offset for the dwmac 5.10. After fixing this it works as before:
|[ 106.359577] imx-dwmac 428a0000.ethernet eth1: configured EST
|[ 128.430715] imx-dwmac 428a0000.ethernet eth1: EST: SWOL has been switched
Tested on imx93.
Fixes: c3f3b97238 ("net: stmmac: Refactor EST implementation")
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Link: https://lore.kernel.org/r/20240220-stmmac_est-v1-1-c41f9ae2e7b7@linutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In newer hardware, IPA supports more than 32 endpoints. Some
registers--such as IPA interrupt registers--represent endpoints
as bits in a 4-byte register, and such registers are repeated as
needed to represent endpoints beyond the first 32.
In ipa_interrupt_suspend_clear_all(), we clear all pending IPA
suspend interrupts by reading all status register(s) and writing
corresponding registers to clear interrupt conditions.
Unfortunately the number of registers to read/write is calculated
incorrectly, and as a result we access *many* more registers than
intended. This bug occurs only when the IPA hardware signals a
SUSPEND interrupt, which happens when a packet is received for an
endpoint (or its underlying GSI channel) that is suspended. This
situation is difficult to reproduce, but possible.
Fix this by correctly computing the number of interrupt registers to
read and write. This is the only place in the code where registers
that map endpoints or channels this way perform this calculation.
Fixes: f298ba785e ("net: ipa: add a parameter to suspend registers")
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
AF reserves MCAM entries for each PF, VF present in the
system and populates the entry with DMAC and action with
default RSS so that basic packet I/O works. Since PF/VF is
not aware of the RSS action installed by AF, AF only fixup
the actions of the rules installed by PF/VF with corresponding
default RSS action. This worked well for rules installed by
PF/VF for features like RX VLAN offload and DMAC filters but
rules involving action like drop/forward to queue are also
getting modified by AF. Hence fix it by setting the default
RSS action only if requested by PF/VF.
Fixes: 967db3529e ("octeontx2-af: add support for multicast/promisc packet replication feature")
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 91fdbce7e8 ("ice: Add support in the driver for associating
queue with napi") invoked the netif_queue_set_napi() call. This
kernel function requires to be called with rtnl_lock taken,
otherwise ASSERT_RTNL() warning will be triggered. ice_vsi_rebuild()
initiating this call is under rtnl_lock when the rebuild is in
response to configuration changes from external interfaces (such as
tc, ethtool etc. which holds the lock). But, the VSI rebuild
generated from service tasks and resets (PFR/CORER/GLOBR) is not
under rtnl lock protection. Handle these cases as well to hold lock
before the kernel call (by setting the 'locked' boolean to false).
netif_queue_set_napi() is also used to clear previously set napi
in the q_vector unroll flow. Handle this for locked/lockless execution
paths.
Fixes: 91fdbce7e8 ("ice: Add support in the driver for associating queue with napi")
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Reviewed-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Do not allow to set phase adjust value for a pin if PF reset is in
progress, this would cause confusing netlink extack errors as the firmware
cannot process the request properly during the reset time.
Return (-EBUSY) and report extack error for the user who tries configure
pin phase adjust during the reset time.
Test by looping execution of below steps until netlink error appears:
- perform PF reset
$ echo 1 > /sys/class/net/<ice PF>/device/reset
- change pin phase adjust value:
$ ./tools/net/ynl/cli.py --spec Documentation/netlink/specs/dpll.yaml \
--do pin-set --json '{"id":0, "phase-adjust":1000}'
Fixes: 90e1c90750 ("ice: dpll: implement phase related callbacks")
Reviewed-by: Igor Bagnucki <igor.bagnucki@intel.com>
Signed-off-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Do not allow dpll periodic work function to acquire data from firmware
if PF reset is in progress. Acquiring data will cause dmesg errors as the
firmware cannot respond or process the request properly during the reset
time.
Test by looping execution of below step until dmesg error appears:
- perform PF reset
$ echo 1 > /sys/class/net/<ice PF>/device/reset
Fixes: d7999f5ea6 ("ice: implement dpll interface to control cgu")
Reviewed-by: Igor Bagnucki <igor.bagnucki@intel.com>
Signed-off-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Do not allow to acquire data or alter configuration of dpll and pins
through firmware if PF reset is in progress, this would cause confusing
netlink extack errors as the firmware cannot respond or process the
request properly during the reset time.
Return (-EBUSY) and extack error for the user who tries access/modify
the config of dpll/pin through firmware during the reset time.
The PF reset and kernel access to dpll data are both asynchronous. It is
not possible to guard all the possible reset paths with any determinictic
approach. I.e., it is possible that reset starts after reset check is
performed (or if the reset would be checked after mutex is locked), but at
the same time it is not possible to wait for dpll mutex unlock in the
reset flow.
This is best effort solution to at least give a clue to the user
what is happening in most of the cases, knowing that there are possible
race conditions where the user could see a different error received
from firmware due to reset unexpectedly starting.
Test by looping execution of below steps until netlink error appears:
- perform PF reset
$ echo 1 > /sys/class/net/<ice PF>/device/reset
- i.e. try to alter/read dpll/pin config:
$ ./tools/net/ynl/cli.py --spec Documentation/netlink/specs/dpll.yaml \
--dump pin-get
Fixes: d7999f5ea6 ("ice: implement dpll interface to control cgu")
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The value of phase_adjust for input pin shall be updated in
ice_dpll_pin_state_update(..). Fix by adding proper argument to the
firmware query function call - a pin's struct field pointer where the
phase_adjust value during driver runtime is stored.
Previously the phase_adjust used to misinform user about actual
phase_adjust value. I.e., if phase_adjust was set to a non zero value and
if driver was reloaded, the user would see the value equal 0, which is
not correct - the actual value is equal to value set before driver reload.
Fixes: 90e1c90750 ("ice: dpll: implement phase related callbacks")
Reviewed-by: Alan Brady <alan.brady@intel.com>
Signed-off-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Fix the connection state between source DPLL and output pin, updating the
attribute 'state' of 'parent_device'. Previously, the connection state
was broken, and didn't reflect the correct state.
When 'state_on_dpll_set' is called with the value
'DPLL_PIN_STATE_CONNECTED' (1), the output pin will switch to the given
DPLL, and the state of the given DPLL will be set to connected.
E.g.:
--do pin-set --json '{"id":2, "parent-device":{"parent-id":1,
"state": 1 }}'
This command will connect DPLL device with id 1 to output pin with id 2.
When 'state_on_dpll_set' is called with the value
'DPLL_PIN_STATE_DISCONNECTED' (2) and the given DPLL is currently
connected, then the output pin will be disabled.
E.g:
--do pin-set --json '{"id":2, "parent-device":{"parent-id":1,
"state": 2 }}'
This command will disable output pin with id 2 if DPLL device with ID 1 is
connected to it; otherwise, the command is ignored.
Fixes: d7999f5ea6 ("ice: implement dpll interface to control cgu")
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Reviewed-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Signed-off-by: Yochai Hagvi <yochai.hagvi@intel.com>
Tested-by: Sunitha Mekala <sunithax.d.mekala@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
FORTIFY_SOURCE has been ignoring 0-sized destinations while the kernel
code base has been converted to flexible arrays. In order to enforce
the 0-sized destinations (e.g. with __counted_by), the remaining 0-sized
destinations need to be handled. Unfortunately, struct vic_provinfo
resists full conversion, as it contains a flexible array of flexible
arrays, which is only possible with the 0-sized fake flexible array.
Use unsafe_memcpy() to avoid future false positives under
CONFIG_FORTIFY_SOURCE.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since there is a utility available for this, use
the API rather than open code.
Fixes: 13943d6c82 ("ionic: prevent pci disable of already disabled device")
Reviewed-by: Brett Creeley <brett.creeley@amd.com>
Signed-off-by: Shannon Nelson <shannon.nelson@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A sanity check for OOB write is off by one leading to a false positive
when the array is full.
Fixes: 9b90aca97f ("net: ethernet: bcmasp: fix possible OOB write in bcmasp_netfilt_get_all_active()")
Signed-off-by: Justin Chen <justin.chen@broadcom.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid the PHY library call unnecessarily into the suspend/resume
functions by setting phydev->mac_managed_pm to true. The ASP driver
essentially does exactly what mdio_bus_phy_resume() does.
Fixes: 490cb41200 ("net: bcmasp: Add support for ASP2.0 Ethernet controller")
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Justin Chen <justin.chen@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If 'dev' or 'data' is NULL, the 'priv' variable has an incorrect address
when dereferencing calling netdev_err().
Since we get as 'dev_id' or 'data' what was passed as the 'dev' argument
to request_irq() during interrupt initialization (that is, the net_device
and rx/tx queue pointers initialized at the time of the call) and since
there are usually no checks for the 'dev_id' argument in such handlers
in other drivers, remove these checks from the handlers in stmmac driver.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: 8532f613bc ("net: stmmac: introduce MSI Interrupt routines for mac, safety, RX & TX")
Signed-off-by: Pavel Sakharov <p.sakharov@ispras.ru>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver uses functions that are supplied by the Kconfig symbol
PHYLIB, so select it to ensure that they are built as needed.
When CONFIG_ADIN1110=y and CONFIG_PHYLIB=m, there are multiple build
(linker) errors that are resolved by this Kconfig change:
ld: drivers/net/ethernet/adi/adin1110.o: in function `adin1110_net_open':
drivers/net/ethernet/adi/adin1110.c:933: undefined reference to `phy_start'
ld: drivers/net/ethernet/adi/adin1110.o: in function `adin1110_probe_netdevs':
drivers/net/ethernet/adi/adin1110.c:1603: undefined reference to `get_phy_device'
ld: drivers/net/ethernet/adi/adin1110.c:1609: undefined reference to `phy_connect'
ld: drivers/net/ethernet/adi/adin1110.o: in function `adin1110_disconnect_phy':
drivers/net/ethernet/adi/adin1110.c:1226: undefined reference to `phy_disconnect'
ld: drivers/net/ethernet/adi/adin1110.o: in function `devm_mdiobus_alloc':
include/linux/phy.h:455: undefined reference to `devm_mdiobus_alloc_size'
ld: drivers/net/ethernet/adi/adin1110.o: in function `adin1110_register_mdiobus':
drivers/net/ethernet/adi/adin1110.c:529: undefined reference to `__devm_mdiobus_register'
ld: drivers/net/ethernet/adi/adin1110.o: in function `adin1110_net_stop':
drivers/net/ethernet/adi/adin1110.c:958: undefined reference to `phy_stop'
ld: drivers/net/ethernet/adi/adin1110.o: in function `adin1110_disconnect_phy':
drivers/net/ethernet/adi/adin1110.c:1226: undefined reference to `phy_disconnect'
ld: drivers/net/ethernet/adi/adin1110.o: in function `adin1110_adjust_link':
drivers/net/ethernet/adi/adin1110.c:1077: undefined reference to `phy_print_status'
ld: drivers/net/ethernet/adi/adin1110.o: in function `adin1110_ioctl':
drivers/net/ethernet/adi/adin1110.c:790: undefined reference to `phy_do_ioctl'
ld: drivers/net/ethernet/adi/adin1110.o:(.rodata+0xf60): undefined reference to `phy_ethtool_get_link_ksettings'
ld: drivers/net/ethernet/adi/adin1110.o:(.rodata+0xf68): undefined reference to `phy_ethtool_set_link_ksettings'
Fixes: bc93e19d08 ("net: ethernet: adi: Add ADIN1110 support")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202402070626.eZsfVHG5-lkp@intel.com/
Cc: Lennart Franzen <lennart@lfdomain.com>
Cc: Alexandru Tachici <alexandru.tachici@analog.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: netdev@vger.kernel.org
Reviewed-by: Nuno Sa <nuno.sa@analog.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2024-02-06 (igb, igc)
This series contains updates to igb and igc drivers.
Kunwu Chan adjusts firmware version string implementation to resolve
possible NULL pointer issue for igb.
Sasha removes workaround on igc.
* '1GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
igc: Remove temporary workaround
igb: Fix string truncation warnings in igb_set_fw_version
====================
Link: https://lore.kernel.org/r/20240214180347.3219650-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
