Pull tty / serial updates from Greg KH:
"Here is the big set of tty and serial driver changes for 6.8-rc1.
As usual, Jiri has a bunch of refactoring and cleanups for the tty
core and drivers in here, along with the usual set of rs485 updates
(someday this might work properly...)
Along with those, in here are changes for:
- sc16is7xx serial driver updates
- platform driver removal api updates
- amba-pl011 driver updates
- tty driver binding updates
- other small tty/serial driver updates and changes
All of these have been in linux-next for a while with no reported
issues"
* tag 'tty-6.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (197 commits)
serial: sc16is7xx: refactor EFR lock
serial: sc16is7xx: reorder code to remove prototype declarations
serial: sc16is7xx: refactor FIFO access functions to increase commonality
serial: sc16is7xx: drop unneeded MODULE_ALIAS
serial: sc16is7xx: replace hardcoded divisor value with BIT() macro
serial: sc16is7xx: add explicit return for some switch default cases
serial: sc16is7xx: add macro for max number of UART ports
serial: sc16is7xx: add driver name to struct uart_driver
serial: sc16is7xx: use i2c_get_match_data()
serial: sc16is7xx: use spi_get_device_match_data()
serial: sc16is7xx: use DECLARE_BITMAP for sc16is7xx_lines bitfield
serial: sc16is7xx: improve do/while loop in sc16is7xx_irq()
serial: sc16is7xx: remove obsolete loop in sc16is7xx_port_irq()
serial: sc16is7xx: set safe default SPI clock frequency
serial: sc16is7xx: add check for unsupported SPI modes during probe
serial: sc16is7xx: fix invalid sc16is7xx_lines bitfield in case of probe error
serial: 8250_exar: Set missing rs485_supported flag
serial: omap: do not override settings for RS485 support
serial: core, imx: do not set RS485 enabled if it is not supported
serial: core: make sure RS485 cannot be enabled when it is not supported
...
Requesting a retune before switching to the RPMB partition has been
observed to cause CRC errors on the RPMB reads (-EILSEQ).
Since RPMB reads can not be retried, the clients would be directly
affected by the errors.
This commit disables the retune request prior to switching to the RPMB
partition: mmc_retune_pause() no longer triggers a retune before the
pause period begins.
This was verified with the sdhci-of-arasan driver (ZynqMP) configured
for HS200 using two separate eMMC cards (DG4064 and 064GB2). In both
cases, the error was easy to reproduce triggering every few tenths of
reads.
With this commit, systems that were utilizing OP-TEE to access RPMB
variables will experience an enhanced performance. Specifically, when
OP-TEE is configured to employ RPMB as a secure storage solution, it not
only writes the data but also the secure filesystem within the
partition. As a result, retrieving any variable involves multiple RPMB
reads, typically around five.
For context, on ZynqMP, each retune request consumed approximately
8ms. Consequently, reading any RPMB variable used to take at the very
minimum 40ms.
After droping the need to retune before switching to the RPMB partition,
this is no longer the case.
Signed-off-by: Jorge Ramirez-Ortiz <jorge@foundries.io>
Acked-by: Avri Altman <avri.altman@wdc.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20240103112911.2954632-1-jorge@foundries.io
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The eMMC card can be set into write-protected mode to prevent data from
being accidentally modified or deleted. Wp_grp_size (Write Protect Group
Size) refers to an attribute of the eMMC card, used to manage write
protection and is the CSD register [36:32] of the eMMC device. Wp_grp_size
(Write Protect Group Size) indicates how many eMMC blocks are contained in
each write protection group on the eMMC card.
To allow userspace easy access of the CSD register bits, let's add sysfs
node "wp_grp_size".
Signed-off-by: Lin Gui <lin.gui@mediatek.com>
Signed-off-by: Bo Ye <bo.ye@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20231218230532.82427-1-bo.ye@mediatek.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add a test to repeatedly re-tune in between random reads. The test is
non-destructive of data on the card and runs for 30 seconds. It can be
repeated to test for longer durations.
If re-tuning is not supported, the test is skipped.
Example:
# echo 'mmc1:0001' > /sys/bus/mmc/drivers/mmcblk/unbind
# echo 'mmc1:0001' > /sys/bus/mmc/drivers/mmc_test/bind
[ 36.642257] mmc_test mmc1:0001: Card claimed for testing.
# cat /sys/kernel/debug/mmc1/mmc1\:0001/testlist | grep tuning
52: Re-tuning reliability
# echo 52 > /sys/kernel/debug/mmc1/mmc1\:0001/test
[ 91.522555] mmc1: Starting tests of card mmc1:0001...
[ 91.528425] mmc1: Test case 52. Re-tuning reliability...
[ 121.536682] mmc1: Result: OK
[ 121.539572] mmc1: Tests completed.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20231214090902.43628-1-adrian.hunter@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Merge the mmc fixes for v6.7-rc[n] into the next branch, to allow them to
get tested together with the new mmc changes that are targeted for v6.8.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Merge the mmc fixes for v6.7-rc[n] into the next branch, to allow them to
get tested together with the new mmc changes that are targeted for v6.8.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When RPMB was converted to a character device, it added support for
multiple RPMB partitions (Commit 97548575be ("mmc: block: Convert RPMB to
a character device").
One of the changes in this commit was transforming the variable target_part
defined in __mmc_blk_ioctl_cmd into a bitmask. This inadvertently regressed
the validation check done in mmc_blk_part_switch_pre() and
mmc_blk_part_switch_post(), so let's fix it.
Fixes: 97548575be ("mmc: block: Convert RPMB to a character device")
Signed-off-by: Jorge Ramirez-Ortiz <jorge@foundries.io>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20231201153143.1449753-1-jorge@foundries.io
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Field Firmware Update (ffu) may use close-ended or open ended sequence.
Each such sequence is comprised of a write commands enclosed between 2
switch commands - to and from ffu mode. So for the close-ended case, it
will be: cmd6->cmd23-cmd25-cmd6.
Some host controllers however, get confused when multi-block rw is sent
without sbc, and may generate auto-cmd12 which breaks the ffu sequence.
I encountered this issue while testing fwupd (github.com/fwupd/fwupd)
on HP Chromebook x2, a qualcomm based QC-7c, code name - strongbad.
Instead of a quirk, or hooking the request function of the msm ops,
it would be better to fix the ioctl handling and make it use mrq.sbc
instead of issuing SET_BLOCK_COUNT separately.
Signed-off-by: Avri Altman <avri.altman@wdc.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20231129092535.3278-1-avri.altman@wdc.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
During board verification, there is a need to test the various supported
eMMC/SD speed modes. However, since the framework chooses the best mode
supported by the card and the host controller's caps, this currently
necessitates changing the devicetree for every iteration.
Allow the various speed mode host capabilities to be modified via
debugfs in order to allow easier hardware verification. The values to
be written are the raw MMC_CAP* values from include/linux/mmc/host.h.
This is rather low-level, and these defines are not guaranteed to be
stable, but it is perhaps good enough for the intended use case.
MMC_CAP_AGGRESSIVE_PM can also be set, in order to be able to
re-initialize the card without having to physically remove and re-insert
it.
/sys/kernel/debug/mmc0# grep timing ios
timing spec: 9 (mmc HS200)
// Turn on MMC_CAP_AGGRESSIVE_PM and re-trigger runtime suspend
/sys/kernel/debug/mmc0# echo $(($(cat caps) | (1 << 7))) > caps
/sys/kernel/debug/mmc0# echo on > /sys/bus/mmc/devices/mmc0\:0001/power/control
/sys/kernel/debug/mmc0# echo auto > /sys/bus/mmc/devices/mmc0\:0001/power/control
// MMC_CAP2_HS200_1_8V_SDR
/sys/kernel/debug/mmc0# echo $(($(cat caps2) & ~(1 << 5))) > caps2
/sys/kernel/debug/mmc0# echo on > /sys/bus/mmc/devices/mmc0\:0001/power/control
/sys/kernel/debug/mmc0# grep timing ios
timing spec: 8 (mmc DDR52)
Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com>
Link: https://lore.kernel.org/r/20230929-mmc-caps-v2-2-11a4c2d94f15@axis.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Merge the mmc fixes for v6.6-rc[n] into the next branch, to allow them to
get tested together with the new mmc changes that are targeted for v6.7.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The OEMID is an 8-bit binary number rather than 16-bit as the current code
parses for. The OEMID occupies bits [111:104] in the CID register, see the
eMMC spec JESD84-B51 paragraph 7.2.3. It seems that the 16-bit comes from
the legacy MMC specs (v3.31 and before).
Let's fix the parsing by simply move to use 8-bit instead of 16-bit. This
means we ignore the impact on some of those old MMC cards that may be out
there, but on the other hand this shouldn't be a problem as the OEMID seems
not be an important feature for these cards.
Signed-off-by: Avri Altman <avri.altman@wdc.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20230927071500.1791882-1-avri.altman@wdc.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Merge the mmc fixes for v6.6-rc[n] into the next branch, to allow them to
get tested together with the new mmc changes that are targeted for v6.7.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
To allow dynamical updates of the current number of used in-flight
requests, let's move away from using a hard-coded value to a use a
corresponding variable in the struct mmc_host.
This can be valuable when optimizing for certain I/O request sequences, as
shown by subsequent changes.
Signed-off-by: Wenchao Chen <wenchao.chen@unisoc.com>
Link: https://lore.kernel.org/r/20230919074707.25517-2-wenchao.chen@unisoc.com
[Ulf: Re-wrote the commitmsg to clarify the change]
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Userspace has currently no way of checking the internal R1 response error
bits for some commands. This is a problem for some commands, like RPMB for
example. Typically, we may detect that the busy completion has successfully
ended, while in fact the card did not complete the requested operation.
To fix the problem, let's always poll with CMD13 for these commands and
during the polling, let's also aggregate the R1 response bits. Before
completing the ioctl request, let's propagate the R1 response bits too.
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Co-developed-by: Christian Loehle <christian.loehle@arm.com>
Signed-off-by: Christian Loehle <christian.loehle@arm.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20230913112921.553019-1-ulf.hansson@linaro.org
Pull tty/serial driver updates from Greg KH:
"Here is the big set of tty and serial driver changes for 6.6-rc1.
Lots of cleanups in here this cycle, and some driver updates. Short
summary is:
- Jiri's continued work to make the tty code and apis be a bit more
sane with regards to modern kernel coding style and types
- cpm_uart driver updates
- n_gsm updates and fixes
- meson driver updates
- sc16is7xx driver updates
- 8250 driver updates for different hardware types
- qcom-geni driver fixes
- tegra serial driver change
- stm32 driver updates
- synclink_gt driver cleanups
- tty structure size reduction
All of these have been in linux-next this week with no reported
issues. The last bit of cleanups from Jiri and the tty structure size
reduction came in last week, a bit late but as they were just style
changes and size reductions, I figured they should get into this merge
cycle so that others can work on top of them with no merge conflicts"
* tag 'tty-6.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (199 commits)
tty: shrink the size of struct tty_struct by 40 bytes
tty: n_tty: deduplicate copy code in n_tty_receive_buf_real_raw()
tty: n_tty: extract ECHO_OP processing to a separate function
tty: n_tty: unify counts to size_t
tty: n_tty: use u8 for chars and flags
tty: n_tty: simplify chars_in_buffer()
tty: n_tty: remove unsigned char casts from character constants
tty: n_tty: move newline handling to a separate function
tty: n_tty: move canon handling to a separate function
tty: n_tty: use MASK() for masking out size bits
tty: n_tty: make n_tty_data::num_overrun unsigned
tty: n_tty: use time_is_before_jiffies() in n_tty_receive_overrun()
tty: n_tty: use 'num' for writes' counts
tty: n_tty: use output character directly
tty: n_tty: make flow of n_tty_receive_buf_common() a bool
Revert "tty: serial: meson: Add a earlycon for the T7 SoC"
Documentation: devices.txt: Fix minors for ttyCPM*
Documentation: devices.txt: Remove ttySIOC*
Documentation: devices.txt: Remove ttyIOC*
serial: 8250_bcm7271: improve bcm7271 8250 port
...
To support the need for host specific tuning for SD high-speed mode, let's
add two new optional callbacks, ->prepare|execute_sd_hs_tuning() and let's
call them when switching into the SD high-speed mode.
Note that, during the tuning process it's also needed for host drivers to
send commands to the SD card to verify that the tuning process succeeds.
Therefore, let's also share the corresponding functions from the core to
allow this.
Signed-off-by: Wenchao Chen <wenchao.chen@unisoc.com>
Link: https://lore.kernel.org/r/20230825091743.15613-2-wenchao.chen@unisoc.com
[Ulf: Dropped unnecessary function declarations and updated the commit msg]
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Yangtao Li <frank.li@vivo.com>
Link: https://lore.kernel.org/r/20230727070051.17778-55-frank.li@vivo.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Yangtao Li <frank.li@vivo.com>
Link: https://lore.kernel.org/r/20230727070051.17778-54-frank.li@vivo.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Yangtao Li <frank.li@vivo.com>
Link: https://lore.kernel.org/r/20230727070051.17778-53-frank.li@vivo.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Merge the mmc fixes for v6.5-rc[n] into the next branch, to allow them to
get tested together with the new mmc changes that are targeted for v6.6.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
For a completed request, after the mmc_blk_mq_complete_rq(mq, req)
function is executed, the bitmap_tags corresponding to the
request will be cleared, that is, the request will be regarded as
idle. If the request is acquired by a different type of process at
this time, the issue_type of the request may change. It further
caused the value of mq->in_flight[issue_type] to be abnormal,
and a large number of requests could not be sent.
p1: p2:
mmc_blk_mq_complete_rq
blk_mq_free_request
blk_mq_get_request
blk_mq_rq_ctx_init
mmc_blk_mq_dec_in_flight
mmc_issue_type(mq, req)
This strategy can ensure the consistency of issue_type
before and after executing mmc_blk_mq_complete_rq.
Fixes: 81196976ed ("mmc: block: Add blk-mq support")
Cc: stable@vger.kernel.org
Signed-off-by: Yibin Ding <yibin.ding@unisoc.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20230802023023.1318134-1-yunlong.xing@unisoc.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Pull MMC updates from Ulf Hansson:
"MMC core:
- Allow synchronous detection of (e)MMC/SD/SDIO cards
- Fixup error check for ioctls for SPI hosts
- Disable broken SD-Cache support for Kingston Canvas Go Plus from 2019
- Disable broken eMMC-Trim support for Kingston EMMC04G-M627
- Disable broken eMMC-Trim support for Micron MTFC4GACAJCN-1M
MMC host:
- bcm2835: Convert DT bindings to YAML
- mmci:
- Enable asynchronous probe
- Transform the ux500 HW-busy detection into a proper state machine
- Add support for SW busy-end timeouts for the ux500 variants
- mmci_stm32:
- Add support for sdm32 variant revision v3.0 used on STM32MP25
- Improve the tuning sequence
- mtk-sd: Tune polling-period to improve performance
- sdhci: Fixup DMA configuration for 64-bit DMA mode
- sdhci-bcm-kona: Convert DT bindings to YAML
- sdhci-msm:
- Switch to use the new ICE API
- Add support for the SC8280XP/IPQ6018/QDU1000/QRU1000 variants
- sdhci-pci-gli:
- Add support SD Express cards for GL9767
- Add support for the Genesys Logic GL9767 variant"
* tag 'mmc-v6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (42 commits)
dt-bindings: mmc: fsl-imx-esdhc: Add imx6ul support
mmc: mmci: Add support for SW busy-end timeouts
mmc: Add MMC_QUIRK_BROKEN_SD_CACHE for Kingston Canvas Go Plus from 11/2019
mmc: core: disable TRIM on Kingston EMMC04G-M627
mmc: mmci: stm32: add delay block support for STM32MP25
mmc: mmci: stm32: prepare other delay block support
mmc: mmci: stm32: manage block gap hardware flow control
mmc: mmci: Add support for sdmmc variant revision v3.0
mmc: mmci: add stm32_idmabsize_align parameter
dt-bindings: mmc: mmci: Add st,stm32mp25-sdmmc2 compatible
mmc: core: disable TRIM on Micron MTFC4GACAJCN-1M
mmc: mmci: Break out a helper function
mmc: mmci: Use a switch statement machine
mmc: mmci: Use state machine state as exit condition
mmc: mmci: Retry the busy start condition
mmc: mmci: Make busy complete state machine explicit
mmc: mmci: Break out error check in busy detect
mmc: mmci: Stash status while waiting for busy
mmc: mmci: Unwind big if() clause
mmc: mmci: Clear busy_status when starting command
...
Pull block updates from Jens Axboe:
- NVMe pull request via Keith:
- Various cleanups all around (Irvin, Chaitanya, Christophe)
- Better struct packing (Christophe JAILLET)
- Reduce controller error logs for optional commands (Keith)
- Support for >=64KiB block sizes (Daniel Gomez)
- Fabrics fixes and code organization (Max, Chaitanya, Daniel
Wagner)
- bcache updates via Coly:
- Fix a race at init time (Mingzhe Zou)
- Misc fixes and cleanups (Andrea, Thomas, Zheng, Ye)
- use page pinning in the block layer for dio (David)
- convert old block dio code to page pinning (David, Christoph)
- cleanups for pktcdvd (Andy)
- cleanups for rnbd (Guoqing)
- use the unchecked __bio_add_page() for the initial single page
additions (Johannes)
- fix overflows in the Amiga partition handling code (Michael)
- improve mq-deadline zoned device support (Bart)
- keep passthrough requests out of the IO schedulers (Christoph, Ming)
- improve support for flush requests, making them less special to deal
with (Christoph)
- add bdev holder ops and shutdown methods (Christoph)
- fix the name_to_dev_t() situation and use cases (Christoph)
- decouple the block open flags from fmode_t (Christoph)
- ublk updates and cleanups, including adding user copy support (Ming)
- BFQ sanity checking (Bart)
- convert brd from radix to xarray (Pankaj)
- constify various structures (Thomas, Ivan)
- more fine grained persistent reservation ioctl capability checks
(Jingbo)
- misc fixes and cleanups (Arnd, Azeem, Demi, Ed, Hengqi, Hou, Jan,
Jordy, Li, Min, Yu, Zhong, Waiman)
* tag 'for-6.5/block-2023-06-23' of git://git.kernel.dk/linux: (266 commits)
scsi/sg: don't grab scsi host module reference
ext4: Fix warning in blkdev_put()
block: don't return -EINVAL for not found names in devt_from_devname
cdrom: Fix spectre-v1 gadget
block: Improve kernel-doc headers
blk-mq: don't insert passthrough request into sw queue
bsg: make bsg_class a static const structure
ublk: make ublk_chr_class a static const structure
aoe: make aoe_class a static const structure
block/rnbd: make all 'class' structures const
block: fix the exclusive open mask in disk_scan_partitions
block: add overflow checks for Amiga partition support
block: change all __u32 annotations to __be32 in affs_hardblocks.h
block: fix signed int overflow in Amiga partition support
block: add capacity validation in bdev_add_partition()
block: fine-granular CAP_SYS_ADMIN for Persistent Reservation
block: disallow Persistent Reservation on partitions
reiserfs: fix blkdev_put() warning from release_journal_dev()
block: fix wrong mode for blkdev_get_by_dev() from disk_scan_partitions()
block: document the holder argument to blkdev_get_by_path
...
This microSD card never clears Flush Cache bit after cache flush has
been started in sd_flush_cache(). This leads e.g. to failure to mount
file system. Add a quirk which disables the SD cache for this specific
card from specific manufacturing date of 11/2019, since on newer dated
cards from 05/2023 the cache flush works correctly.
Fixes: 08ebf903af ("mmc: core: Fixup support for writeback-cache for eMMC and SD")
Signed-off-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20230620102713.7701-1-marex@denx.de
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
It seems that Kingston EMMC04G-M627 despite advertising TRIM support does
not work when the core is trying to use REQ_OP_WRITE_ZEROES.
We are seeing I/O errors in OpenWrt under 6.1 on Zyxel NBG7815 that we did
not previously have and tracked it down to REQ_OP_WRITE_ZEROES.
Trying to use fstrim seems to also throw errors like:
[93010.835112] I/O error, dev loop0, sector 16902 op 0x3:(DISCARD) flags 0x800 phys_seg 1 prio class 2
Disabling TRIM makes the error go away, so lets add a quirk for this eMMC
to disable TRIM.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20230619193621.437358-1-robimarko@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
It seems that Micron MTFC4GACAJCN-1M despite advertising TRIM support does
not work when the core is trying to use REQ_OP_WRITE_ZEROES.
We are seeing the following errors in OpenWrt under 6.1 on Qnap Qhora 301W
that we did not previously have and tracked it down to REQ_OP_WRITE_ZEROES:
[ 18.085950] I/O error, dev loop0, sector 596 op 0x9:(WRITE_ZEROES) flags 0x800 phys_seg 0 prio class 2
Disabling TRIM makes the error go away, so lets add a quirk for this eMMC
to disable TRIM.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20230530213259.1776512-1-robimarko@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When using dm-verity with a data partition on an emmc device, dm-verity
races with the initialization of the (e)MMC/SD cards. This is because the
card detection procedure is being managed from a workqueue, rather than
synchronously from the mmc host's ->probe() routine.
To allow the card detect to be synchronous, let's simply skip using the
workqueue at the first initialization attempt from mmc_start_host().
Signed-off-by: Dennis Zhou <dennis@kernel.org>
Link: https://lore.kernel.org/r/ZCTOMVjW+pnZVGsQ@snowbird
[Ulf: Re-wrote the commit message to clarify the change]
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The only overlap between the block open flags mapped into the fmode_t and
other uses of fmode_t are FMODE_READ and FMODE_WRITE. Define a new
blk_mode_t instead for use in blkdev_get_by_{dev,path}, ->open and
->ioctl and stop abusing fmode_t.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Jack Wang <jinpu.wang@ionos.com> [rnbd]
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Christian Brauner <brauner@kernel.org>
Link: https://lore.kernel.org/r/20230608110258.189493-28-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
