Pull LED updates from Lee Jones:
"New Drivers:
- Add support for Allwinner A100 RGB LED controller
- Add support for Maxim 5970 Dual Hot-swap controller
New Device Support:
- Add support for AW20108 to Awinic LED driver
New Functionality:
- Extend support for Net speeds to include; 2.5G, 5G and 10G
- Allow tx/rx and cts/dsr/dcd/rng TTY LEDS to be turned on and off
via sysfs if required
- Add support for hardware control in AW200xx
Fix-ups:
- Use safer methods for string handling
- Improve error handling; return proper error values, simplify,
avoid duplicates, etc
- Replace Mutex use with the Completion mechanism
- Fix include lists; alphabetise, remove unused, explicitly add used
- Use generic platform device properties
- Use/convert to new/better APIs/helpers/MACROs instead of
hand-rolling implementations
- Device Tree binding adaptions/conversions/creation
- Continue work to remove superfluous platform .remove() call-backs
- Remove superfluous/defunct code
- Trivial; whitespace, unused variables, spelling, clean-ups, etc
- Avoid unnecessary duplicate locks
Bug Fixes:
- Repair Kconfig based dependency lists
- Ensure unused dynamically allocated data is freed after use
- Fix support for brightness control
- Add missing sufficient delays during reset to ensure correct
operation
- Avoid division-by-zero issues"
* tag 'leds-next-6.8' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/leds: (45 commits)
leds: trigger: netdev: Add core support for hw not supporting fallback to LED sw control
leds: trigger: panic: Don't register panic notifier if creating the trigger failed
leds: sun50i-a100: Convert to be agnostic to property provider
leds: max5970: Add missing headers
leds: max5970: Make use of dev_err_probe()
leds: max5970: Make use of device properties
leds: max5970: Remove unused variable
leds: rgb: Drop obsolete dependency on COMPILE_TEST
leds: sun50i-a100: Avoid division-by-zero warning
leds: trigger: Remove unused function led_trigger_rename_static()
leds: qcom-lpg: Introduce a wrapper for getting driver data from a pwm chip
leds: gpio: Add kernel log if devm_fwnode_gpiod_get() fails
dt-bindings: leds: qcom,spmi-flash-led: Fix example node name
dt-bindings: leds: aw200xx: Fix led pattern and add reg constraints
dt-bindings: leds: awinic,aw200xx: Add AW20108 device
leds: aw200xx: Add support for aw20108 device
leds: aw200xx: Improve autodim calculation method
leds: aw200xx: Enable disable_locking flag in regmap config
leds: aw200xx: Add delay after software reset
dt-bindings: leds: aw200xx: Remove property "awinic,display-rows"
...
Pull pwm updates from Thierry Reding:
"This contains a bunch of cleanups and simplifications across the
board, as well as a number of small fixes.
Perhaps the most notable change here is the addition of an API that
allows PWMs to be used in atomic contexts, which is useful when time-
critical operations are involved, such as using a PWM to generate IR
signals.
Finally, I have decided to step down as PWM subsystem maintainer. Due
to other responsibilities I have lately not been able to find the time
that the subsystem deserves and Uwe, who has been helping out a lot
for the past few years and has many things planned for the future, has
kindly volunteered to take over. I have no doubt that he will be a
suitable replacement"
* tag 'pwm/for-6.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm: (44 commits)
MAINTAINERS: pwm: Thierry steps down, Uwe takes over
pwm: linux/pwm.h: fix Excess kernel-doc description warning
pwm: Add pwm_apply_state() compatibility stub
pwm: cros-ec: Drop documentation for dropped struct member
pwm: Drop two unused API functions
pwm: lpc18xx-sct: Don't modify the cached period of other PWM outputs
pwm: meson: Simplify using dev_err_probe()
pwm: stmpe: Silence duplicate error messages
pwm: Reduce number of pointer dereferences in pwm_device_request()
pwm: crc: Use consistent variable naming for driver data
pwm: omap-dmtimer: Drop locking
dt-bindings: pwm: ti,pwm-omap-dmtimer: Update binding for yaml
media: pwm-ir-tx: Trigger edges from hrtimer interrupt context
pwm: bcm2835: Allow PWM driver to be used in atomic context
pwm: Make it possible to apply PWM changes in atomic context
pwm: renesas: Remove unused include
pwm: Replace ENOTSUPP with EOPNOTSUPP
pwm: Rename pwm_apply_state() to pwm_apply_might_sleep()
pwm: Stop referencing pwm->chip
pwm: Update kernel doc for struct pwm_chip
...
If hw doesn't support sw control of the LED and we switch to a mode
not supported by hw, currently we get lots of errors because neither
brigthness_set() nor brithness_set_blocking() is set.
Deal with this by not falling back to sw control, and return
-EOPNOTSUPP to the user. Note that we still store the new mode.
This is needed in case an intermediate unsupported mode is necessary
to switch from one supported mode to another.
Add a comment explaining how a driver for such hw is supposed to behave.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/3fd5184c-3641-4b0b-b59a-f489ec69a6cd@gmail.com
Signed-off-by: Lee Jones <lee@kernel.org>
In order to introduce a pwm api which can be used from atomic context,
we will need two functions for applying pwm changes:
int pwm_apply_might_sleep(struct pwm *, struct pwm_state *);
int pwm_apply_atomic(struct pwm *, struct pwm_state *);
This commit just deals with renaming pwm_apply_state(), a following
commit will introduce the pwm_apply_atomic() function.
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> # for input
Acked-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Acked-by: Lee Jones <lee@kernel.org>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
When CONFIG_COMMON_CLK is disabled, e.g. on an x86 randconfig compile test,
clang reports a field overflow from propagating the result of a division by
zero:
drivers/leds/leds-sun50i-a100.c:309:12: error: call to '__compiletime_assert_265' declared with 'error' attribute: FIELD_PREP: value too large for the field
control = FIELD_PREP(LEDC_T01_TIMING_CTRL_REG_T1H, timing->t1h_ns / cycle_ns) |
Avoid the problem by adding an explicit check for the zero value here. Alternatively
the assertion could be avoided with a Kconfig dependency on COMMON_CLK.
Fixes: 090a25ad9798 ("leds: sun50i-a100: New driver for the A100 LED controller")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Guo Ren <guoren@kernel.org>
Link: https://lore.kernel.org/r/20231212214536.175327-1-arnd@kernel.org
Signed-off-by: Lee Jones <lee@kernel.org>
In case leds-gpio fails to get at least one of possibly many GPIOs
from the DT (e.g. the GPIO is already requested) neither gpiolib nor
the driver does provide any helpful error log:
leds-gpio: probe of leds failed with error -16
As the driver knows better how to handle errors with such mandatory
GPIOs, let's implement an error log which points to the affected
GPIO.
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20231202183636.7055-1-wahrenst@gmx.net
Signed-off-by: Lee Jones <lee@kernel.org>
HWEN is hardware control, which is used for enable/disable aw200xx chip.
It's high active, internally pulled down to GND.
After HWEN pin set high the chip begins to load the OTP information,
which takes 200us to complete. About 200us wait time is needed for
internal oscillator startup and display SRAM initialization. After
display SRAM initialization, the registers in page 1 to page 5 can be
configured via i2c interface.
Signed-off-by: Dmitry Rokosov <ddrokosov@salutedevices.com>
Link: https://lore.kernel.org/r/20231125200519.1750-3-ddrokosov@salutedevices.com
Signed-off-by: Lee Jones <lee@kernel.org>
The serial tty interface also supports additional input signals, that
can also be evaluated within this trigger. This change is adding the
following additional input sources, which could be controlled
via the '/sys/class/<leds>/' sysfs interface.
Explanation:
DCE = Data Communication Equipment (Modem)
DTE = Data Terminal Equipment (Computer)
- cts:
DCE is ready to accept data from the DTE (CTS = Clear To Send). If
the line state is detected, the LED is switched on.
If set to 0 (default), the LED will not evaluate CTS.
If set to 1, the LED will evaluate CTS.
- dsr:
DCE is ready to receive and send data (DSR = Data Set Ready). If the
line state is detected, the LED is switched on.
If set to 0 (default), the LED will not evaluate DSR.
If set to 1, the LED will evaluate DSR.
- dcd:
DTE is receiving a carrier from the DCE (DCD = Data Carrier Detect).
If the line state is detected, the LED is switched on.
If set to 0 (default), the LED will not evaluate DCD.
If set to 1, the LED will evaluate DCD.
- rng:
DCE has detected an incoming ring signal on the telephone line
(RNG = Ring Indicator). If the line state is detected, the LED is
switched on.
If set to 0 (default), the LED will not evaluate RNG.
If set to 1, the LED will evaluate RNG.
Also add an invert flag on LED blink, so that the LED blinks in the
correct order.
* If one off the new enabled input signals are evaluatet as 'enabled',
and data are transmitted, then the LED should first blink 'off' and
then 'on' (invert).
* If all the new enabled input signals are evaluatet as 'disabled',
and data are transmitted, then the LED should first blink 'on' and
then 'off'.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
Reviewed-by: Maarten Brock <m.brock@vanmierlo.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20231127110311.3583957-5-fe@dev.tdt.de
Signed-off-by: Lee Jones <lee@kernel.org>
Until now, the LED blinks when data is sent via the tty (rx/tx).
This is not configurable.
This change adds the possibility to make the indication for the direction
of the transmitted data independently controllable via the new rx and
tx sysfs entries.
- rx:
Signal reception (rx) of data on the named tty device.
If set to 0, the LED will not blink on reception.
If set to 1 (default), the LED will blink on reception.
- tx:
Signal transmission (tx) of data on the named tty device.
If set to 0, the LED will not blink on transmission.
If set to 1 (default), the LED will blink on transmission.
This new sysfs entry are on by default. Thus the trigger behaves as
before this change.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20231127110311.3583957-4-fe@dev.tdt.de
Signed-off-by: Lee Jones <lee@kernel.org>
With this commit, the mutex handling is replaced by the completion
handling. When handling mutex, it must always be ensured that the held
mutex is also released again. This is more error-prone should the number
of code paths increase.
This is a preparatory commit to make the trigger more configurable via
additional sysfs parameters. With this change, the worker always runs and
is no longer stopped if no ttyname is set.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20231127110311.3583957-3-fe@dev.tdt.de
Signed-off-by: Lee Jones <lee@kernel.org>
Pull pwm updates from Thierry Reding:
"This contains a few fixes and a bunch of cleanups, a lot of which is
in preparation for Uwe's character device support that may be ready in
time for the next merge window"
* tag 'pwm/for-6.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm: (37 commits)
pwm: samsung: Document new member .channel in struct samsung_pwm_chip
pwm: bcm2835: Add support for suspend/resume
pwm: brcmstb: Checked clk_prepare_enable() return value
pwm: brcmstb: Utilize appropriate clock APIs in suspend/resume
pwm: pxa: Explicitly include correct DT includes
pwm: cros-ec: Simplify using devm_pwmchip_add() and dev_err_probe()
pwm: samsung: Consistently use the same name for driver data
pwm: vt8500: Simplify using devm functions
pwm: sprd: Simplify using devm_pwmchip_add() and dev_err_probe()
pwm: sprd: Provide a helper to cast a chip to driver data
pwm: spear: Simplify using devm functions
pwm: mtk-disp: Simplify using devm_pwmchip_add()
pwm: imx-tpm: Simplify using devm functions
pwm: brcmstb: Simplify using devm functions
pwm: bcm2835: Simplify using devm functions
pwm: bcm-iproc: Simplify using devm functions
pwm: Adapt sysfs API documentation to reality
pwm: dwc: add PWM bit unset in get_state call
pwm: dwc: make timer clock configurable
pwm: dwc: split pci out of core driver
...
Pull LED updates from Lee Jones:
"Core Frameworks:
- Add support for a bunch more colours
New Drivers:
- Add support for Kinetic KTD2026/7 RGB/White LEDs
New Functionality:
- Add support for device to enter HW Controlled Mode to Turris Omnia
LEDs
- Add support for HW Gamma Correction to Turris Omnia LEDs
Fix-ups:
- Apply new __counted_by() annotation to several data structures
containing flexible arrays
- Rid the return value from Platform's .remove() operation
- Use *_cansleep() variants for instances were threads can sleep
- Improve the semantics when setting the brightness
- Generic clean-ups; code reduction, coding style, standard patterns
- Replace strncpy() with strscpy()
- Fix-up / add various documentation
- Re-author the GPIO associated Trigger to use trigger-sources
- Move to using standard APIs and helpers
- Improve error checking
- Stop using static GPIO bases
Bug Fixes:
- Fix Pointer to Enum casing warnings
- Do not pretend that I2C backed device supports SMBUS
- Ensure PWM LEDs are extinguished when disabled, rather than held in
a state
- Fix 'output may be truncated' warnings"
* tag 'leds-next-6.7' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/leds: (43 commits)
leds: lp5521: Add an error check in lp5521_post_init_device
leds: gpio: Update headers
leds: gpio: Remove unneeded assignment
leds: gpio: Move temporary variable for struct device to gpio_led_probe()
leds: gpio: Refactor code to use devm_gpiod_get_index_optional()
leds: gpio: Utilise PTR_ERR_OR_ZERO()
leds: gpio: Keep driver firmware interface agnostic
leds: core: Refactor led_update_brightness() to use standard pattern
leds: turris-omnia: Fix brightness setting and trigger activating
leds: sc27xx: Move mutex_init() down
leds: trigger: netdev: Move size check in set_device_name
leds: Add ktd202x driver
dt-bindings: leds: Add Kinetic KTD2026/2027 LED
leds: core: Add more colors from DT bindings to led_colors
dt-bindings: leds: Last color ID is now 14 (LED_COLOR_ID_LIME)
leds: tca6507: Don't use fixed GPIO base
leds: lp3952: Convert to use maple tree register cache
leds: lm392x: Convert to use maple tree register cache
leds: aw200xx: Convert to use maple tree register cache
leds: lm3601x: Convert to use maple tree register cache
...
