The FORCE_STOP_STATE bit is unsuitable to force the DSI link into LP-11
mode. It seems the bridge internally queues DSI packets and when the
FORCE_STOP_STATE bit is cleared, they are sent in close succession
without any useful timing (this also means that the DSI lanes won't go
into LP-11 mode). The length of this gibberish varies between 1ms and
5ms. This sometimes breaks an attached bridge (TI SN65DSI84 in this
case). In our case, the bridge will fail in about 1 per 500 reboots.
The FORCE_STOP_STATE handling was introduced to have the DSI lanes in
LP-11 state during the .pre_enable phase. But as it turns out, none of
this is needed at all. Between samsung_dsim_init() and
samsung_dsim_set_display_enable() the lanes are already in LP-11 mode.
The code as it was before commit 20c827683d ("drm: bridge:
samsung-dsim: Fix init during host transfer") and 0c14d31306 ("drm:
bridge: samsung-dsim: Fix i.MX8M enable flow to meet spec") was correct
in this regard.
This patch basically reverts both commits. It was tested on an i.MX8M
SoC with an SN65DSI84 bridge. The signals were probed and the DSI
packets were decoded during initialization and link start-up. After this
patch the first DSI packet on the link is a VSYNC packet and the timing
is correct.
Command mode between .pre_enable and .enable was also briefly tested by
a quick hack. There was no DSI link partner which would have responded,
but it was made sure the DSI packet was send on the link. As a side
note, the command mode seems to just work in HS mode. I couldn't find
that the bridge will handle commands in LP mode.
Fixes: 20c827683d ("drm: bridge: samsung-dsim: Fix init during host transfer")
Fixes: 0c14d31306 ("drm: bridge: samsung-dsim: Fix i.MX8M enable flow to meet spec")
Signed-off-by: Michael Walle <mwalle@kernel.org>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231113164344.1612602-1-mwalle@kernel.org
Pull i2c updates from Wolfram Sang:
"This removes the currently unused CLASS_DDC support (controllers set
the flag, but there is no client to use it).
Also, CLASS_SPD support gets simplified to prepare removal in the
future. Class based instantiation is not recommended these days
anyhow.
Furthermore, I2C core now creates a debugfs directory per I2C adapter.
Current bus driver users were converted to use it.
Finally, quite some driver updates. Standing out are patches for the
wmt-driver which is refactored to support more variants.
This is the rebased pull request where a large series for the
designware driver was dropped"
* tag 'i2c-for-6.8-rc1-rebased' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (38 commits)
MAINTAINERS: use proper email for my I2C work
i2c: stm32f7: add support for stm32mp25 soc
i2c: stm32f7: perform I2C_ISR read once at beginning of event isr
dt-bindings: i2c: document st,stm32mp25-i2c compatible
i2c: stm32f7: simplify status messages in case of errors
i2c: stm32f7: perform most of irq job in threaded handler
i2c: stm32f7: use dev_err_probe upon calls of devm_request_irq
i2c: i801: Add lis3lv02d for Dell XPS 15 7590
i2c: i801: Add lis3lv02d for Dell Precision 3540
i2c: wmt: Reduce redundant: REG_CR setting
i2c: wmt: Reduce redundant: function parameter
i2c: wmt: Reduce redundant: clock mode setting
i2c: wmt: Reduce redundant: wait event complete
i2c: wmt: Reduce redundant: bus busy check
i2c: mux: reg: Remove class-based device auto-detection support
i2c: make i2c_bus_type const
dt-bindings: at24: add ROHM BR24G04
eeprom: at24: use of_match_ptr()
i2c: cpm: Remove linux,i2c-index conversion from be32
i2c: imx: Make SDA actually optional for bus recovering
...
The ps8640 bridge seems to expect everything to be power cycled at the
disable process, but sometimes ps8640_aux_transfer() holds the runtime
PM reference and prevents the bridge from suspend.
Prevent that by introducing a mutex lock between ps8640_aux_transfer()
and .post_disable() to make sure the bridge is really powered off.
Fixes: 826cff3f7e ("drm/bridge: parade-ps8640: Enable runtime power management")
Signed-off-by: Pin-yen Lin <treapking@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240109120528.1292601-1-treapking@chromium.org
A null pointer dereference crash has been observed rarely on TI
platforms using sii9022 bridge:
[ 53.271356] sii902x_get_edid+0x34/0x70 [sii902x]
[ 53.276066] sii902x_bridge_get_edid+0x14/0x20 [sii902x]
[ 53.281381] drm_bridge_get_edid+0x20/0x34 [drm]
[ 53.286305] drm_bridge_connector_get_modes+0x8c/0xcc [drm_kms_helper]
[ 53.292955] drm_helper_probe_single_connector_modes+0x190/0x538 [drm_kms_helper]
[ 53.300510] drm_client_modeset_probe+0x1f0/0xbd4 [drm]
[ 53.305958] __drm_fb_helper_initial_config_and_unlock+0x50/0x510 [drm_kms_helper]
[ 53.313611] drm_fb_helper_initial_config+0x48/0x58 [drm_kms_helper]
[ 53.320039] drm_fbdev_dma_client_hotplug+0x84/0xd4 [drm_dma_helper]
[ 53.326401] drm_client_register+0x5c/0xa0 [drm]
[ 53.331216] drm_fbdev_dma_setup+0xc8/0x13c [drm_dma_helper]
[ 53.336881] tidss_probe+0x128/0x264 [tidss]
[ 53.341174] platform_probe+0x68/0xc4
[ 53.344841] really_probe+0x188/0x3c4
[ 53.348501] __driver_probe_device+0x7c/0x16c
[ 53.352854] driver_probe_device+0x3c/0x10c
[ 53.357033] __device_attach_driver+0xbc/0x158
[ 53.361472] bus_for_each_drv+0x88/0xe8
[ 53.365303] __device_attach+0xa0/0x1b4
[ 53.369135] device_initial_probe+0x14/0x20
[ 53.373314] bus_probe_device+0xb0/0xb4
[ 53.377145] deferred_probe_work_func+0xcc/0x124
[ 53.381757] process_one_work+0x1f0/0x518
[ 53.385770] worker_thread+0x1e8/0x3dc
[ 53.389519] kthread+0x11c/0x120
[ 53.392750] ret_from_fork+0x10/0x20
The issue here is as follows:
- tidss probes, but is deferred as sii902x is still missing.
- sii902x starts probing and enters sii902x_init().
- sii902x calls drm_bridge_add(). Now the sii902x bridge is ready from
DRM's perspective.
- sii902x calls sii902x_audio_codec_init() and
platform_device_register_data()
- The registration of the audio platform device causes probing of the
deferred devices.
- tidss probes, which eventually causes sii902x_bridge_get_edid() to be
called.
- sii902x_bridge_get_edid() tries to use the i2c to read the edid.
However, the sii902x driver has not set up the i2c part yet, leading
to the crash.
Fix this by moving the drm_bridge_add() to the end of the
sii902x_init(), which is also at the very end of sii902x_probe().
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Fixes: 21d808405f ("drm/bridge/sii902x: Fix EDID readback")
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20240103-si902x-fixes-v1-1-b9fd3e448411@ideasonboard.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240103-si902x-fixes-v1-1-b9fd3e448411@ideasonboard.com
Pull drm updates from Dave Airlie:
"This contains two major new drivers:
- imagination is a first driver for Imagination Technologies devices,
it only covers very specific devices, but there is hope to grow it
- xe is a reboot of the i915 GPU (shares display) side using a more
upstream focused development model, and trying to maximise code
sharing. It's not enabled for any hw by default, and will hopefully
get switched on for Intel's Lunarlake.
This also drops a bunch of the old UMS ioctls. It's been dead long
enough.
amdgpu has a bunch of new color management code that is being used in
the Steam Deck.
amdgpu also has a new ACPI WBRF interaction to help avoid radio
interference.
Otherwise it's the usual lots of changes in lots of places.
Detailed summary:
new drivers:
- imagination - new driver for Imagination Technologies GPU
- xe - new driver for Intel GPUs using core drm concepts
core:
- add CLOSE_FB ioctl
- remove old UMS ioctls
- increase max objects to accomodate AMD color mgmt
encoder:
- create per-encoder debugfs directory
edid:
- split out drm_eld
- SAD helpers
- drop edid_firmware module parameter
format-helper:
- cache format conversion buffers
sched:
- move from kthread to workqueue
- rename some internals
- implement dynamic job-flow control
gpuvm:
- provide more features to handle GEM objects
client:
- don't acquire module reference
displayport:
- add mst path property documentation
fdinfo:
- alignment fix
dma-buf:
- add fence timestamp helper
- add fence deadline support
bridge:
- transparent aux-bridge for DP/USB-C
- lt8912b: add suspend/resume support and power regulator support
panel:
- edp: AUO B116XTN02, BOE NT116WHM-N21,836X2, NV116WHM-N49
- chromebook panel support
- elida-kd35t133: rework pm
- powkiddy RK2023 panel
- himax-hx8394: drop prepare/unprepare and shutdown logic
- BOE BP101WX1-100, Powkiddy X55, Ampire AM8001280G
- Evervision VGG644804, SDC ATNA45AF01
- nv3052c: register docs, init sequence fixes, fascontek FS035VG158
- st7701: Anbernic RG-ARC support
- r63353 panel controller
- Ilitek ILI9805 panel controller
- AUO G156HAN04.0
simplefb:
- support memory regions
- support power domains
amdgpu:
- add new 64-bit sequence number infrastructure
- add AMD specific color management
- ACPI WBRF support for RF interference handling
- GPUVM updates
- RAS updates
- DCN 3.5 updates
- Rework PCIe link speed handling
- Document GPU reset types
- DMUB fixes
- eDP fixes
- NBIO 7.9/7.11 updates
- SubVP updates
- XGMI PCIe state dumping for aqua vanjaram
- GFX11 golden register updates
- enable tunnelling on high pri compute
amdkfd:
- Migrate TLB flushing logic to amdgpu
- Trap handler fixes
- Fix restore workers handling on suspend/resume
- Fix possible memory leak in pqm_uninit()
- support import/export of dma-bufs using GEM handles
radeon:
- fix possible overflows in command buffer checking
- check for errors in ring_lock
i915:
- reorg display code for reuse in xe driver
- fdinfo memory stats printing
- DP MST bandwidth mgmt improvements
- DP panel replay enabling
- MTL C20 phy state verification
- MTL DP DSC fractional bpp support
- Audio fastset support
- use dma_fence interfaces instead of i915_sw_fence
- Separate gem and display code
- AUX register macro refactoring
- Separate display module/device parameters
- Move display capabilities debugfs under display
- Makefile cleanups
- Register cleanups
- Move display lock inits under display/
- VLV/CHV DPIO PHY register and interface refactoring
- DSI VBT sequence refactoring
- C10/C20 PHY PLL hardware readout
- DPLL code cleanups
- Cleanup PXP plane protection checks
- Improve display debug msgs
- PSR selective fetch fixes/improvements
- DP MST fixes
- Xe2LPD FBC restrictions removed
- DGFX uses direct VBT pin mapping
- more MTL WAs
- fix MTL eDP bug
- eliminate use of kmap_atomic
habanalabs:
- sysfs entry to identify a device minor id with debugfs path
- sysfs entry to expose device module id
- add signed device info retrieval through INFO ioctl
- add Gaudi2C device support
- pcie reset prepare/done hooks
msm:
- Add support for SDM670, SM8650
- Handle the CFG interconnect to fix the obscure hangs / timeouts
- Kconfig fix for QMP dependency
- use managed allocators
- DPU: SDM670, SM8650 support
- DPU: Enable SmartDMA on SM8350 and SM8450
- DP: enable runtime PM support
- GPU: add metadata UAPI
- GPU: move devcoredumps to GPU device
- GPU: convert to drm_exec
ivpu:
- update FW API
- new debugfs file
- a new NOP job submission test mode
- improve suspend/resume
- PM improvements
- MMU PT optimizations
- firmware profile frequency support
- support for uncached buffers
- switch to gem shmem helpers
- replace kthread with threaded irqs
rockchip:
- rk3066_hdmi: convert to atomic
- vop2: support nv20 and nv30
- rk3588 support
mediatek:
- use devm_platform_ioremap_resource
- stop using iommu_present
- MT8188 VDOSYS1 display support
panfrost:
- PM improvements
- improve interrupt handling as poweroff
qaic:
- allow to run with single MSI
- support host/device time sync
- switch to persistent DRM devices
exynos:
- fix potential error pointer dereference
- fix wrong error checking
- add missing call to drm_atomic_helper_shutdown
omapdrm:
- dma-fence lockdep annotation fix
tidss:
- dma-fence lockdep annotation fix
- support for AM62A7
v3d:
- BCM2712 - rpi5 support
- fdinfo + gputop support
- uapi for CPU job handling
virtio-gpu:
- add context debug name"
* tag 'drm-next-2024-01-10' of git://anongit.freedesktop.org/drm/drm: (2340 commits)
drm/amd/display: Allow z8/z10 from driver
drm/amd/display: fix bandwidth validation failure on DCN 2.1
drm/amdgpu: apply the RV2 system aperture fix to RN/CZN as well
drm/amd/display: Move fixpt_from_s3132 to amdgpu_dm
drm/amd/display: Fix recent checkpatch errors in amdgpu_dm
Revert "drm/amdkfd: Relocate TBA/TMA to opposite side of VM hole"
drm/amd/display: avoid stringop-overflow warnings for dp_decide_lane_settings()
drm/amd/display: Fix power_helpers.c codestyle
drm/amd/display: Fix hdcp_log.h codestyle
drm/amd/display: Fix hdcp2_execution.c codestyle
drm/amd/display: Fix hdcp_psp.h codestyle
drm/amd/display: Fix freesync.c codestyle
drm/amd/display: Fix hdcp_psp.c codestyle
drm/amd/display: Fix hdcp1_execution.c codestyle
drm/amd/pm/smu7: fix a memleak in smu7_hwmgr_backend_init
drm/amdkfd: Fix iterator used outside loop in 'kfd_add_peer_prop()'
drm/amdgpu: Drop 'fence' check in 'to_amdgpu_amdkfd_fence()'
drm/amdkfd: Confirm list is non-empty before utilizing list_first_entry in kfd_topology.c
drm/amdgpu: Fix '*fw' from request_firmware() not released in 'amdgpu_ucode_request()'
drm/amdgpu: Fix variable 'mca_funcs' dereferenced before NULL check in 'amdgpu_mca_smu_get_mca_entry()'
...
Unlike what is claimed in commit f5aa7d46b0 ("drm/bridge:
parade-ps8640: Provide wait_hpd_asserted() in struct drm_dp_aux"), if
someone manually tries to do an AUX transfer (like via `i2cdump ${bus}
0x50 i`) while the panel is off we don't just get a simple transfer
error. Instead, the whole ps8640 gets thrown for a loop and goes into
a bad state.
Let's put the function to wait for the HPD (and the magical 50 ms
after first reset) back in when we're doing an AUX transfer. This
shouldn't actually make things much slower (assuming the panel is on)
because we should immediately poll and see the HPD high. Mostly this
is just an extra i2c transfer to the bridge.
Fixes: f5aa7d46b0 ("drm/bridge: parade-ps8640: Provide wait_hpd_asserted() in struct drm_dp_aux")
Tested-by: Pin-yen Lin <treapking@chromium.org>
Reviewed-by: Pin-yen Lin <treapking@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20231221135548.1.I10f326a9305d57ad32cee7f8d9c60518c8be20fb@changeid
After commit 26195af577 ("drm/bridge: ps8640: Drop the ability of
ps8640 to fetch the EDID"), I got an error compiling:
error: comparison of distinct pointer types
('typeof (len) *' (aka 'unsigned int *') and
'typeof (msg->size) *' (aka 'unsigned long *'))
[-Werror,-Wcompare-distinct-pointer-types]
Fix it by declaring the `len` as size_t.
The above error only shows up on downstream kernels without commit
d03eba99f5 ("minmax: allow min()/max()/clamp() if the arguments have
the same signedness."), but since commit 26195af577 ("drm/bridge:
ps8640: Drop the ability of ps8640 to fetch the EDID") is a "Fix" that
will likely be backported it seems nice to make it easy. ...plus it's
more correct to declare `len` as size_t anyway.
Fixes: 26195af577 ("drm/bridge: ps8640: Drop the ability of ps8640 to fetch the EDID")
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20231218090454.1.I5c6eb80b2f746439c4b58efab788e00701d08759@changeid
drm-misc-next for $kernel-version:
UAPI Changes:
Cross-subsystem Changes:
- A few fixes for usb/typec
Core Changes:
- ci: Updates to the defconfig, igt version, etc.
- writeback: Move the atomic_check helper from the encoder to connector
Driver Changes:
- rockchip: Add support for rk3588
- xe: Update the TODO list
- panel:
- nv3052c: Register documentation, init sequence improvements and
support for the Fascontek FS035VG158
- st7701: Add support for the Anbernic RG-ARC
- new driver: Synaptics R63353 panel controller, Ilitek ILI9805 panel
controller
- new panel: AUO G156HAN04.0
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maxime Ripard <mripard@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/aqpn5miejmkks7pbcfex7b6u63uwsruywxsnr3x5ljs45qatin@nbkkej2elk46
For aux reads, the value `msg->size` indicates the size of the buffer
provided by `msg->buffer`. We should never in any circumstances write
more bytes to the buffer since it may overflow the buffer.
In the ti-sn65dsi86 driver there is one code path that reads the
transfer length from hardware. Even though it's never been seen to be
a problem, we should make extra sure that the hardware isn't
increasing the length since doing so would cause us to overrun the
buffer.
Fixes: 982f589bde ("drm/bridge: ti-sn65dsi86: Update reply on aux failures")
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Guenter Roeck <groeck@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20231214123752.v3.2.I7b83c0f31aeedc6b1dc98c7c741d3e1f94f040f8@changeid
While testing, I happened to notice a random crash that looked like:
Kernel panic - not syncing: stack-protector:
Kernel stack is corrupted in: drm_dp_dpcd_probe+0x120/0x120
Analysis of drm_dp_dpcd_probe() shows that we pass in a 1-byte buffer
(allocated on the stack) to the aux->transfer() function. Presumably
if the aux->transfer() writes more than one byte to this buffer then
we're in a bad shape.
Dropping into kgdb, I noticed that "aux->transfer" pointed at
ps8640_aux_transfer().
Reading through ps8640_aux_transfer(), I can see that there are cases
where it could write more bytes to msg->buffer than were specified by
msg->size. This could happen if the hardware reported back something
bogus to us. Let's fix this so we never write more than msg->size
bytes. We'll still read all the bytes from the hardware just in case
the hardware requires it since the aux transfer data comes through an
auto-incrementing register.
NOTE: I have no actual way to reproduce this issue but it seems likely
this is what was happening in the crash I looked at.
Fixes: 13afcdd727 ("drm/bridge: parade-ps8640: Add support for AUX channel")
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Guenter Roeck <groeck@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20231214123752.v3.1.I9d1afcaad76a3e2c0ca046dc4adbc2b632c22eda@changeid
It's the ti_sn65dsi86.pwm auxiliary driver that creates the pwmchip, so
let the auxiliary device be the parent of the pwm device.
Note that getting a reference to the ti-sn65dsi86's pwm using pwm_get()
isn't affected by this change as ti_sn65dsi86_add_aux_device() sets the
auxiliary device's of_node to that of the main device.
Also change PM runtime tracking and diagnostic messages to use that one.
After enabling runtime PM operation for the auxiliary device, all works
as expected as parent devices are handled just fine.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Tested-by: Nikita Travkin <nikita@trvn.ru> # Acer Aspire 1
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20231209153108.1988551-2-u.kleine-koenig@pengutronix.de
The DT of_device.h and of_platform.h date back to the separate
of_platform_bus_type before it was merged into the regular platform bus.
As part of that merge prepping Arm DT support 13 years ago, they
"temporarily" include each other. They also include platform_device.h
and of.h. Soon the implicit includes are going to be removed.
of_device.h isn't needed, but of.h is for of_node_put().
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20231207162501.2629952-1-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
The i2c_master_send/recv() functions return negative error codes or
they return "len" on success. So the error handling here can be written
as just normal checks for "if (ret < 0) return ret;". No need to
complicate things.
Btw, in this code the "len" parameter can never be zero, but even if
it were, then I feel like this would still be the best way to write it.
Fixes: 9144379928 ("drm/bridge: nxp-ptn3460: fix i2c_master_send() error checking")
Suggested-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/04242630-42d8-4920-8c67-24ac9db6b3c9@moroto.mountain
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20231102165640.3307820-24-u.kleine-koenig@pengutronix.de
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20231102165640.3307820-23-u.kleine-koenig@pengutronix.de
Pull pwm updates from Thierry Reding:
"This contains a few fixes and a bunch of cleanups, a lot of which is
in preparation for Uwe's character device support that may be ready in
time for the next merge window"
* tag 'pwm/for-6.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm: (37 commits)
pwm: samsung: Document new member .channel in struct samsung_pwm_chip
pwm: bcm2835: Add support for suspend/resume
pwm: brcmstb: Checked clk_prepare_enable() return value
pwm: brcmstb: Utilize appropriate clock APIs in suspend/resume
pwm: pxa: Explicitly include correct DT includes
pwm: cros-ec: Simplify using devm_pwmchip_add() and dev_err_probe()
pwm: samsung: Consistently use the same name for driver data
pwm: vt8500: Simplify using devm functions
pwm: sprd: Simplify using devm_pwmchip_add() and dev_err_probe()
pwm: sprd: Provide a helper to cast a chip to driver data
pwm: spear: Simplify using devm functions
pwm: mtk-disp: Simplify using devm_pwmchip_add()
pwm: imx-tpm: Simplify using devm functions
pwm: brcmstb: Simplify using devm functions
pwm: bcm2835: Simplify using devm functions
pwm: bcm-iproc: Simplify using devm functions
pwm: Adapt sysfs API documentation to reality
pwm: dwc: add PWM bit unset in get_state call
pwm: dwc: make timer clock configurable
pwm: dwc: split pci out of core driver
...
drm-misc-next for v6.7-rc1:
drm-misc-next-2023-10-19 + following:
UAPI Changes:
Cross-subsystem Changes:
- Convert fbdev drivers to use fbdev i/o mem helpers.
Core Changes:
- Use cross-references for macros in docs.
- Make drm_client_buffer_addb use addfb2.
- Add NV20 and NV30 YUV formats.
- Documentation updates for create_dumb ioctl.
- CI fixes.
- Allow variable number of run-queues in scheduler.
Driver Changes:
- Rename drm/ast constants.
- Make ili9882t its own driver.
- Assorted fixes in ivpu, vc4, bridge/synopsis, amdgpu.
- Add planar formats to rockchip.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/3d92fae8-9b1b-4165-9ca8-5fda11ee146b@linux.intel.com
Freescale i.MX93 SoC embeds a Synopsys Designware MIPI DSI host
controller and a Synopsys Designware MIPI DPHY. Some configurations
and extensions to them are controlled by i.MX93 media blk-ctrl.
Add a DRM bridge for i.MX93 MIPI DSI by using existing DW MIPI DSI
bridge helpers and implementing i.MX93 MIPI DSI specific extensions.
Signed-off-by: Liu Ying <victor.liu@nxp.com>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230821034008.3876938-10-victor.liu@nxp.com
According to Synopsys DW MIPI DSI host databook, HSTX and LPRX timeout
contention detections are measured in TO_CLK_DIVISION cycles. However,
the current driver programs magic values to TO_CLK_DIVISION, HSTX_TO_CNT
and LPRX_TO_CNT register fields, which makes timeout error event wrongly
happen for some video modes, at least for the typical 1920x1080p@60 video
mode read from a HDMI monitor driven by ADV7535 DSI to HDMI bridge.
While at it, the current driver doesn't enable interrupt to handle or
complain about the error status, so true error just happens silently
except for display distortions by visual check.
Disable the timeout check by setting those timeout register fields to
zero for now until someone comes along with better computations for the
timeout values. Although the databook doesn't mention what happens when
they are set to zero, it turns out the false error doesn't happen for
the 1920x1080p@60 video mode at least.
Signed-off-by: Liu Ying <victor.liu@nxp.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230821034008.3876938-8-victor.liu@nxp.com
According to Synopsys support channel, each region of HSA, HBP and HFP must
have minimum number of 10 bytes where constant 4 bytes are for HSS or HSE
and 6 bytes are for blanking packet(header + CRC). Hence, the below table
comes in.
+------------+----------+-------+
| data lanes | min lbcc | bytes |
+------------+----------+-------+
| 1 | 10 | 1*10 |
+------------+----------+-------+
| 2 | 5 | 2*5 |
+------------+----------+-------+
| 3 | 4 | 3*4 |
+------------+----------+-------+
| 4 | 3 | 4*3 |
+------------+----------+-------+
Implement the minimum lbcc numbers to make sure that the values programmed
into DSI_VID_HSA_TIME and DSI_VID_HBP_TIME registers meet the minimum
number requirement. For DSI_VID_HLINE_TIME register, it seems that the
value programmed should be based on mode->htotal as-is, instead of sum up
HSA, HBP, HFP and HDISPLAY.
This helps the case where Raydium RM67191 DSI panel is connected, since
it's video timing for hsync length is only 2 pixels and without this patch
the programmed value for DSI_VID_HSA_TIME is only 2 with 4 data lanes.
Signed-off-by: Liu Ying <victor.liu@nxp.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230821034008.3876938-7-victor.liu@nxp.com
