Add reset/terminate/repeat command for SPI module. In case of SPI commands
failure, the host should issue a RESET command to WILC chip to recover
from any temporary bus error.
For now, the new command support is added and later the SPI read/write
API's would be modified to make use of these commands for retry mechanism
Signed-off-by: Ajay Singh <ajay.kathat@microchip.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210916164902.74629-6-ajay.kathat@microchip.com
Use the correct sequence to configure clockless registers for chip wake-up.
The following sequence is expected from WILC chip for wakeup:
- set wakeup bit in wakeup_reg register
- after setting the wakeup bit, read back the clock status bit for wakeup
complete.
For SDIO/SPI modules, the wakeup sequence is the same except uses different
register values so refactored the code to use common function for both
SDIO/SPI bus.
Signed-off-by: Ajay Singh <ajay.kathat@microchip.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210916164902.74629-5-ajay.kathat@microchip.com
When the BSS reference holds a valid reference, it is not freed. The 'if'
condition is wrong. Instead of the 'if (bss)' check, the 'if (!bss)' check
is used.
The issue is solved by removing the unnecessary 'if' check because
cfg80211_put_bss() already performs the NULL validation.
Fixes: 6cd4fa5ab6 ("staging: wilc1000: make use of cfg80211_inform_bss_frame()")
Signed-off-by: Ajay Singh <ajay.kathat@microchip.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210916164902.74629-3-ajay.kathat@microchip.com
When creating a new virtual interface in mwifiex_add_virtual_intf(), we
update our internal driver states like bss_type, bss_priority, bss_role
and bss_mode to reflect the mode the firmware will be set to.
When switching virtual interface mode using
mwifiex_init_new_priv_params() though, we currently only update bss_mode
and bss_role. In order for the interface mode switch to actually work,
we also need to update bss_type to its proper value, so do that.
This fixes a crash of the firmware (because the driver tries to execute
commands that are invalid in AP mode) when switching from station mode
to AP mode.
Signed-off-by: Jonas Dreßler <verdre@v0yd.nl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210914195909.36035-9-verdre@v0yd.nl
It's possible to change virtual interface type between P2P_CLIENT and
P2P_GO, the card supports that just fine, and it happens for example
when using miracast with the miraclecast software.
So allow type changes between P2P_CLIENT and P2P_GO and simply call into
mwifiex_change_vif_to_p2p(), which handles this just fine. We have to
call mwifiex_cfg80211_deinit_p2p() before though to make sure the old
p2p mode is properly uninitialized.
Signed-off-by: Jonas Dreßler <verdre@v0yd.nl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210914195909.36035-7-verdre@v0yd.nl
In mwifiex_init_new_priv_params() we update our private driver state to
reflect the currently selected virtual interface type. Most notably we
set the bss_mode to the mode we're going to put the firmware in.
Now after we updated the driver state we actually start talking to the
firmware and instruct it to set up the new mode. Those commands can and
will sometimes fail, in which case we return with an error from
mwifiex_change_vif_to_*. We currently update our virtual interface type
counters after this return, which means the code is never reached when a
firmware error happens and we never update the counters. Since we have
updated our bss_mode earlier though, the counters now no longer reflect
the actual state of the driver.
This will break things on the next virtual interface change, because the
virtual interface type we're switching away from didn't get its counter
incremented, and we end up decrementing a 0-counter.
To fix this, simply update the virtual interface type counters right
after updating our driver structures, so that they are always in sync.
Signed-off-by: Jonas Dreßler <verdre@v0yd.nl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210914195909.36035-6-verdre@v0yd.nl
Use a small helper function to increment and decrement the counter of
the interface types we currently manage. This makes the code that
actually changes and sets up the interface type a bit less messy and
also helps avoiding mistakes in case someone increments/decrements a
counter wrongly.
Signed-off-by: Jonas Dreßler <verdre@v0yd.nl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210914195909.36035-5-verdre@v0yd.nl
We currently handle changing from the P2P to the STATION virtual
interface type slightly different than changing from P2P to ADHOC: When
changing to STATION, we don't send the SET_BSS_MODE command. We do send
that command on all other type-changes though, and it probably makes
sense to send the command since after all we just changed our BSS_MODE.
Looking at prior changes to this part of the code, it seems that this is
simply a leftover from old refactorings.
Since sending the SET_BSS_MODE command is the only difference between
mwifiex_change_vif_to_sta_adhoc() and the current code, we can now use
mwifiex_change_vif_to_sta_adhoc() for both switching to ADHOC and
STATION interface type.
This does not fix any particular bug and just "looked right", so there's
a small chance it might be a regression.
Signed-off-by: Jonas Dreßler <verdre@v0yd.nl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210914195909.36035-4-verdre@v0yd.nl
Handle the obvious invalid virtual interface type changes with a general
check instead of looking at the individual change.
For type changes from P2P_CLIENT to P2P_GO and the other way round, this
changes the behavior slightly: We now still do nothing, but return
-EOPNOTSUPP instead of 0. Now that behavior was incorrect before and
still is, because type changes between these two types are actually
possible and supported, which we'll fix in a following commit.
Signed-off-by: Jonas Dreßler <verdre@v0yd.nl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210914195909.36035-2-verdre@v0yd.nl
Current adaptivity mechanism is achieved in driver, by periodically
referencing the IGI value and then updating related registers.
But we find that this way may halt TX activity too long if huge
and temporary energy is detected frequently. So we move the mechanism
to firmware for immediately reacting this case to recover TX rapidly.
Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210830072014.12250-5-pkshih@realtek.com
Add Energy Detected CCA (EDCCA) mechanism to detect energy on the channel.
And EDCCA support adaptivity mode now. From MIC Ordinance Regulating Radio
Equipment article 49.20, ETSI EN-300-328 and EN-301-893, the device should
be able to dynamically pause TX activity when energy detected on the air.
According to ETSI/JP DFS region, driver will set corresponding threshold
and stop TX activity if the detected energy exceeds the threshold. For now,
we support it on 8822b and 8822c first.
By default, EDCCA mechanism is turned on. For ETSI/JP DFS region, it will
turn to adaptivity mode. However, with adaptivity, if environment is too
noisy, TX may often be halted. So, a debugfs for EDCCA is added. It can
show what EDCCA mode is used currently. And EDCCA mechanism can be turned
on/off through the debugfs while debugging.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210830072014.12250-4-pkshih@realtek.com
Realtek chips can program a specific country domain on efuse to
indicate what is the expected rtw_regulatory. For chips with a
programmed country domain, we set REGULATORY_STRICT_REG to tell
stack to consider follow-up regulatory_hint() as the superset of
our regulatory rule. Besides, on driver side, only the request via
NL80211_REGDOM_SET_BY_DRIVER, which matches programmed country
domain, will be handled to keep rtw_regulatory unchanged.
For worldwide roaming chips, i.e. ones without a specific programmed
country domain, system of distro can set expected regulatory via
NL80211_REGDOM_SET_BY_USER. With setting from it, rtw_regulatory
will handle the requests only via NL80211_REGDOM_SET_BY_USER to
follow setting from system of distro. REGULATORY_COUNTRY_IE_IGNORE
will then be set to tell stack to ignore country IE for us. The
restrictions mentioned above will remain until 00, i.e. worldwide,
is set via NL80211_REGDOM_SET_BY_USER.
On the other hand, for worldwide roamin chips, if there is no
specific regulatory set via NL80211_REGDOM_SET_BY_USER, requests
from all regulatory notifications will be handled by rtw_regulatory.
And REGULATORY_COUNTRY_IE_IGNORE won't be set.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210830072014.12250-3-pkshih@realtek.com
Mapping table from country code to rtw_regulatory, which manages tx power
limit according to countries, is updated. And mapping architecture is also
upgraded. For more precise control on tx power limit, it allows different
rtw_regulatory for different bands logically. Besides, a helper function
to query rtw_regulatory for current band under current country is provided.
For older chips, some newly added rtw_regulatory may not be configured.
To avoid that those chips have no limit on some countries mapping to a
newer rtw_regulatory after table update, a backward selection mechanism
of rtw_regulatory is introduced. It can help chips use a rtw_regulatory
which has been configured as an alternative of a newer one which is not
configured.
In addition, rtw88 actually doesn't manage channel plans by itself.
Instead, it follows them from stack. So, correct some naming about
chplan with regd, and remove the unnecessary channel control for now.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210830072014.12250-2-pkshih@realtek.com
P2P client mode was only working the first time.
On subsequent connection attempts the group was successfully created but
no data was sent (no transmitted data packets were seen with a sniffer).
The reason for this was that the hardware was being configured in fixed
rate mode with rate RSI_RATE_1 (1Mbps) which is not valid in the 5GHz band.
In P2P mode wpa_supplicant uses NL80211_CMD_SET_TX_BITRATE_MASK to disallow
the 11b rates in the 2.4GHz band which updated common->fixedrate_mask.
rsi_set_min_rate() then used the fixedrate_mask to calculate the minimum
allowed rate, or 0xffff = auto if none was found.
However that calculation did not account for the different rate sets
allowed in the different bands leading to the error.
Fixing set_min_rate() would result in 6Mb/s being used all the time
which is not what we want either.
The reason the problem did not occur on the first connection is that
rsi_mac80211_set_rate_mask() only updated the fixedrate_mask for
the *current* band. When it was called that was still 2.4GHz as the
switch is done later. So the when set_min_rate() was subsequently
called after the switch to 5GHz it still had a mask of zero, leading
to defaulting to auto mode.
Fix this by differentiating the case of a single rate being
requested, in which case the hardware will be used in fixed rate
mode with just that rate, and multiple rates being requested,
in which case we remain in auto mode but the firmware rate selection
algorithm is configured with a restricted set of rates.
Fixes: dad0d04fa7 ("rsi: Add RS9113 wireless driver")
Signed-off-by: Martin Fuzzey <martin.fuzzey@flowbird.group>
CC: stable@vger.kernel.org
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1630337206-12410-4-git-send-email-martin.fuzzey@flowbird.group
My previous patch checked if encryption should be enabled by directly
checking info->control.hw_key (like the downstream driver).
However that missed that the control and driver_info members of
struct ieee80211_tx_info are union fields.
Due to this when rsi_core_xmit() updates fields in "tx_params"
(driver_info) it can overwrite the control.hw_key, causing the result
of the later test to be incorrect.
With the current structure layout the first byte of control.hw_key is
overlayed with the vap_id so, since we only test if control.hw_key is
NULL / non NULL, a non zero vap_id will incorrectly enable encryption.
In basic STA and AP modes the vap_id is always zero so it works but in
P2P client mode a second VIF is created causing vap_id to be non zero
and hence encryption to be enabled before keys have been set.
Fix this by extracting the key presence flag to a new field in the driver
private tx_params structure and populating it first.
Fixes: 314538041b ("rsi: fix AP mode with WPA failure due to encrypted EAPOL")
Signed-off-by: Martin Fuzzey <martin.fuzzey@flowbird.group>
CC: stable@vger.kernel.org
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1630337206-12410-3-git-send-email-martin.fuzzey@flowbird.group
When BT coexistence is enabled (eg oper mode 13, which is the default)
the initialisation on startup sometimes silently fails.
In a normal initialisation we see
usb 1-1.3: Product: Wireless USB Network Module
usb 1-1.3: Manufacturer: Redpine Signals, Inc.
usb 1-1.3: SerialNumber: 000000000001
rsi_91x: rsi_probe: Initialized os intf ops
rsi_91x: rsi_load_9116_firmware: Loading chunk 0
rsi_91x: rsi_load_9116_firmware: Loading chunk 1
rsi_91x: rsi_load_9116_firmware: Loading chunk 2
rsi_91x: Max Stations Allowed = 1
But sometimes the last log is missing and the wlan net device is
not created.
Running a userspace loop that resets the hardware via a GPIO shows the
problem occurring ~5/100 resets.
The problem does not occur in oper mode 1 (wifi only).
Adding logs shows that the initialisation state machine requests a MAC
reset via rsi_send_reset_mac() but the firmware does not reply, leading
to the initialisation sequence being incomplete.
Fix this by delaying attaching the BT adapter until the wifi
initialisation has completed.
With this applied I have done > 300 reset loops with no errors.
Fixes: 716b840c76 ("rsi: handle BT traffic in driver")
Signed-off-by: Martin Fuzzey <martin.fuzzey@flowbird.group>
CC: stable@vger.kernel.org
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1630337206-12410-2-git-send-email-martin.fuzzey@flowbird.group
Pull networking fixes and stragglers from Jakub Kicinski:
"Networking stragglers and fixes, including changes from netfilter,
wireless and can.
Current release - regressions:
- qrtr: revert check in qrtr_endpoint_post(), fixes audio and wifi
- ip_gre: validate csum_start only on pull
- bnxt_en: fix 64-bit doorbell operation on 32-bit kernels
- ionic: fix double use of queue-lock, fix a sleeping in atomic
- can: c_can: fix null-ptr-deref on ioctl()
- cs89x0: disable compile testing on powerpc
Current release - new code bugs:
- bridge: mcast: fix vlan port router deadlock, consistently disable
BH
Previous releases - regressions:
- dsa: tag_rtl4_a: fix egress tags, only port 0 was working
- mptcp: fix possible divide by zero
- netfilter: nft_ct: protect nft_ct_pcpu_template_refcnt with mutex
- netfilter: socket: icmp6: fix use-after-scope
- stmmac: fix MAC not working when system resume back with WoL active
Previous releases - always broken:
- ip/ip6_gre: use the same logic as SIT interfaces when computing
v6LL address
- seg6: set fc_nlinfo in nh_create_ipv4, nh_create_ipv6
- mptcp: only send extra TCP acks in eligible socket states
- dsa: lantiq_gswip: fix maximum frame length
- stmmac: fix overall budget calculation for rxtx_napi
- bnxt_en: fix firmware version reporting via devlink
- renesas: sh_eth: add missing barrier to fix freeing wrong tx
descriptor
Stragglers:
- netfilter: conntrack: switch to siphash
- netfilter: refuse insertion if chain has grown too large
- ncsi: add get MAC address command to get Intel i210 MAC address"
* tag 'net-5.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (76 commits)
ieee802154: Remove redundant initialization of variable ret
net: stmmac: fix MAC not working when system resume back with WoL active
net: phylink: add suspend/resume support
net: renesas: sh_eth: Fix freeing wrong tx descriptor
bonding: 3ad: pass parameter bond_params by reference
cxgb3: fix oops on module removal
can: c_can: fix null-ptr-deref on ioctl()
can: rcar_canfd: add __maybe_unused annotation to silence warning
net: wwan: iosm: Unify IO accessors used in the driver
net: wwan: iosm: Replace io.*64_lo_hi() with regular accessors
net: qcom/emac: Replace strlcpy with strscpy
ip6_gre: Revert "ip6_gre: add validation for csum_start"
net: hns3: make hclgevf_cmd_caps_bit_map0 and hclge_cmd_caps_bit_map0 static
selftests/bpf: Test XDP bonding nest and unwind
bonding: Fix negative jump label count on nested bonding
MAINTAINERS: add VM SOCKETS (AF_VSOCK) entry
stmmac: dwmac-loongson:Fix missing return value
iwlwifi: fix printk format warnings in uefi.c
net: create netdev->dev_addr assignment helpers
bnxt_en: Fix possible unintended driver initiated error recovery
...
We can reproduce this issue with below steps:
1) enable WoL on the host
2) host system suspended
3) remote client send out wakeup packets
We can see that host system resume back, but can't work, such as ping failed.
After a bit digging, this issue is introduced by the commit 46f69ded98
("net: stmmac: Use resolved link config in mac_link_up()"), which use
the finalised link parameters in mac_link_up() rather than the
parameters in mac_config().
There are two scenarios for MAC suspend/resume in STMMAC driver:
1) MAC suspend with WoL inactive, stmmac_suspend() call
phylink_mac_change() to notify phylink machine that a change in MAC
state, then .mac_link_down callback would be invoked. Further, it will
call phylink_stop() to stop the phylink instance. When MAC resume back,
firstly phylink_start() is called to start the phylink instance, then
call phylink_mac_change() which will finally trigger phylink machine to
invoke .mac_config and .mac_link_up callback. All is fine since
configuration in these two callbacks will be initialized, that means MAC
can restore the state.
2) MAC suspend with WoL active, phylink_mac_change() will put link
down, but there is no phylink_stop() to stop the phylink instance, so it
will link up again, that means .mac_config and .mac_link_up would be
invoked before system suspended. After system resume back, it will do
DMA initialization and SW reset which let MAC lost the hardware setting
(i.e MAC_Configuration register(offset 0x0) is reset). Since link is up
before system suspended, so .mac_link_up would not be invoked after
system resume back, lead to there is no chance to initialize the
configuration in .mac_link_up callback, as a result, MAC can't work any
longer.
After discussed with Russell King [1], we confirm that phylink framework
have not take WoL into consideration yet. This patch calls
phylink_suspend()/phylink_resume() functions which is newly introduced
by Russell King to fix this issue.
[1] https://lore.kernel.org/netdev/20210901090228.11308-1-qiangqing.zhang@nxp.com/
Fixes: 46f69ded98 ("net: stmmac: Use resolved link config in mac_link_up()")
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Joakim Zhang reports that Wake-on-Lan with the stmmac ethernet driver broke
when moving the incorrect handling of mac link state out of mac_config().
This reason this breaks is because the stmmac's WoL is handled by the MAC
rather than the PHY, and phylink doesn't cater for that scenario.
This patch adds the necessary phylink code to handle suspend/resume events
according to whether the MAC still needs a valid link or not. This is the
barest minimum for this support.
Reported-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Tested-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The cur_tx counter must be incremented after TACT bit of
txdesc->status was set. However, a CPU is possible to reorder
instructions and/or memory accesses between cur_tx and
txdesc->status. And then, if TX interrupt happened at such a
timing, the sh_eth_tx_free() may free the descriptor wrongly.
So, add wmb() before cur_tx++.
Otherwise NETDEV WATCHDOG timeout is possible to happen.
Fixes: 86a74ff21a ("net: sh_eth: add support for Renesas SuperH Ethernet")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The parameter bond_params is a relatively large 192 byte sized
struct so pass it by reference rather than by value to reduce
copying.
Addresses-Coverity: ("Big parameter passed by value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Kalle Valo says:
====================
wireless-drivers fixes for v5.15
First set of fixes for v5.15 and only iwlwifi patches this time. Most
important being support for new hardware and new firmware API.
I had already earlier applied a fix which also Linus applied to this
tree as commit 1476ff21ab ("iwl: fix debug printf format strings"),
but this doesn't seem to cause any conflicts so I left it there.
iwlwifi
* add support for firmware API 66
* add support for Samsung Galaxy Book Flex2 Alpha
* fix a leak happening every time module is loaded
* fix a printk compiler warning
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The pdev maybe not a platform device, e.g. c_can_pci device, in this
case, calling to_platform_device() would not make sense. Also, per the
comment in drivers/net/can/c_can/c_can_ethtool.c, @bus_info should
match dev_name() string, so I am replacing this with dev_name() to fix
this issue.
[ 1.458583] BUG: unable to handle page fault for address: 0000000100000000
[ 1.460921] RIP: 0010:strnlen+0x1a/0x30
[ 1.466336] ? c_can_get_drvinfo+0x65/0xb0 [c_can]
[ 1.466597] ethtool_get_drvinfo+0xae/0x360
[ 1.466826] dev_ethtool+0x10f8/0x2970
[ 1.467880] sock_ioctl+0xef/0x300
Fixes: 2722ac986e ("can: c_can: add ethtool support")
Link: https://lore.kernel.org/r/20210906233704.1162666-1-ztong0001@gmail.com
Cc: stable@vger.kernel.org # 5.14+
Signed-off-by: Tong Zhang <ztong0001@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Since commit
| dd3bd23eb4 ("can: rcar_canfd: Add Renesas R-Car CAN FD driver")
the rcar_canfd driver can be compile tested on all architectures. On
non OF enabled archs, or archs where OF is optional (and disabled in
the .config) the compilation throws the following warning:
| drivers/net/can/rcar/rcar_canfd.c:2020:34: warning: unused variable 'rcar_canfd_of_table' [-Wunused-const-variable]
| static const struct of_device_id rcar_canfd_of_table[] = {
| ^
This patch fixes the warning by marking the variable
rcar_canfd_of_table as __maybe_unused.
Fixes: ac42240873 ("can: rcar: Kconfig: Add helper dependency on COMPILE_TEST")
Fixes: dd3bd23eb4 ("can: rcar_canfd: Add Renesas R-Car CAN FD driver")
Link: https://lore.kernel.org/all/20210907064537.1054268-1-mkl@pengutronix.de
Cc: linux-renesas-soc@vger.kernel.org
Cc: Cai Huoqing <caihuoqing@baidu.com>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The variable 'package_size' is an unsigned long, and should be printed
out using '%lu', not '%zd' (that would be for a size_t).
Yes, on many architectures (including x86-64), 'size_t' is in fact the
same type as 'long', but that's a fairly random architecture definition,
and on some platforms 'size_t' is in fact 'int' rather than 'long'.
That is the case on traditional 32-bit x86. Yes, both types are the
exact same 32-bit size, and it would all print out perfectly correctly,
but '%zd' ends up still being wrong.
And we can't make 'package_size' be a 'size_t', because we get the
actual value using efivar_entry_get() that takes a pointer to an
'unsigned long'. So '%lu' it is.
This fixes two of the i386 allmodconfig build warnings (that is now an
error due to -Werror).
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently we have readl()/writel()/ioread*()/iowrite*() APIs in use.
Let's unify to use only ioread*()/iowrite*() variants.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The io.*_lo_hi() variants are not strictly needed on the x86 hardware
and especially the PCI bus. Replace them with regular accessors, but
leave headers in place in case of 32-bit build.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The strlcpy should not be used because it doesn't limit the source
length. As linus says, it's a completely useless function if you
can't implicitly trust the source string - but that is almost always
why people think they should use it! All in all the BSD function
will lead some potential bugs.
But the strscpy doesn't require reading memory from the src string
beyond the specified "count" bytes, and since the return value is
easier to error-check than strlcpy()'s. In addition, the implementation
is robust to the string changing out from underneath it, unlike the
current strlcpy() implementation.
Thus, We prefer using strscpy instead of strlcpy.
Signed-off-by: Jason Wang <wangborong@cdjrlc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This symbols is not used outside of hclge_cmd.c and hclgevf_cmd.c, so marks
it static.
Fix the following sparse warning:
drivers/net/ethernet/hisilicon/hns3/hns3vf/hclgevf_cmd.c:345:35:
warning: symbol 'hclgevf_cmd_caps_bit_map0' was not declared. Should it
be static?
drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_cmd.c:365:33: warning:
symbol 'hclge_cmd_caps_bit_map0' was not declared. Should it be static?
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: chongjiapeng <jiapeng.chong@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With nested bonding devices the nested bond device's ndo_bpf was
called without a program causing it to decrement the static key
without a prior increment leading to negative count.
Fix the issue by 1) only calling slave's ndo_bpf when there's a
program to be loaded and 2) only decrement the count when a program
is unloaded.
Fixes: 9e2ee5c7e7 ("net, bonding: Add XDP support to the bonding driver")
Reported-by: syzbot+30622fb04ddd72a4d167@syzkaller.appspotmail.com
Signed-off-by: Jussi Maki <joamaki@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
