Add support for BCM53128 internal PHYs. These support interrupts as well as
statistics. Therefore, enable the Broadcom PHY driver for them.
Tested on BCM53128 switch using the mainline b53 DSA driver.
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some structures and defines were added with '_ub_' indication, as there
were equivalent objects for the legacy model.
Now when the legacy model is not used anymore, remove the '_ub_'
indication.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The flood_index() function is not needed anymore, as in the unified
bridge model the flood index is calculated using 'mid_base' and
'fid_offset'.
Remove this function.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After all the preparations for unified bridge model, finally flip mlxsw
driver to use the new model.
Change config profile, set 'ubridge' to true and remove the configurations
that are relevant only for the legacy model. Set 'flood_mode' to
'controlled' as the current mode is not supported with unified bridge
model.
Remove all the code which is dedicated to the legacy model. Remove
'struct mlxsw_sp.ubridge' variable which was temporarily added to separate
configurations between the models.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The unified bridge model is enabled via the CONFIG_PROFILE command
during driver initialization. Add the definition of the relevant fields
to the command's payload in preparation for unified bridge enablement.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using the legacy bridge model, there is no VID classification at egress
for 802.1Q FIDs, which means that the VID is maintained.
This behavior cause the limitation that 802.1Q FIDs cannot work with VXLAN.
This limitation stems from the fact that a decapsulated VXLAN packet should
not contain a VLAN tag. If such a packet was to egress from a local port
using a 802.1Q FID, it would "maintain" its VLAN on egress, which is no
VLAN at all.
Currently 802.1Q FIDs are emulated in mlxsw driver using 802.1D FIDs. Using
unified bridge model, there is a FID->VID mapping, so it is possible to
stop emulating 802.1Q FIDs.
The main changes are:
1. Use 'SFGC.bridge_type' = 0, to separate between 802.1Q FIDs and
802.1D FIDs.
2. Use VLAN RIF instead of the emulated one (VLAN_EMU which is emulated
using FID RIF).
3. Create VID->FID mapping when the FID is created. Then when a new port
is mapped to the FID, if it not in virtual mode, no new mapping is
needed. Save the new port in 'port_vid_list', to be able to update a
RIF in all {Port, VID}->FID mappings in case that the port will be in
virtual mode later.
4. Add a dedicated operation function per FID family to update RIF for
VID->FID mappings. For 802.1d and rFID families, just return. For
802.1q family, handle the global mapping which is created for new 802.1q
FID.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the unified bridge model, mlxsw will no longer emulate 802.1Q FIDs
using 802.1D FIDs. The new FID table will look as follows:
+---------------+
| 802.1q FIDs | 4K entries
| [1..4094] |
+---------------+
| 802.1d FIDs | 1K entries
| [4095..5118] |
+---------------+
| Dummy FIDs | 1 entry
| [5119..5119] |
+---------------+
| rFIDs | 11K entries
| [5120..16383] |
+---------------+
In order to make the change easier to review, four new temporary FID
families will be added (e.g., MLXSW_SP_FID_TYPE_8021D_UB) and will not
be registered with the FID core until mlxsw is flipped to use the unified
bridge model.
Add .1d, rfid and dummy FID families for unified bridge, the next patch
will add .1q family separately as it requires more changes.
The following changes are required:
1. Add 'smpe_index_valid' field to 'struct mlxsw_sp_fid_family' and set
SFMR.smpe accordingly. SMPE index is reserved for rFIDs, as their
flooding is handled by firmware, and always reserved in Spectrum-1,
as it is configured as part of PGT table.
2. Add 'ubridge' field to 'struct mlxsw_sp_fid_family'. This field will
be removed later, use it in mlxsw_sp_fid_family_{register,unregister}()
to skip the registration / unregistration of the new families when the
legacy model is used.
3. Indexes - the start and end indexes of each FID family will need to be
changed according to the above diagram.
4. Add flood tables for unified bridge model, use 'fid_offset' as table
type, as in the new model the access to flood tables will be using
'fid_offset' calculation.
5. FID family operation changes:
a. rFID supposed to be created using SFMR, as it is not created by
firmware using unified bridge model.
b. port_vid_map() should perform SVFA for rFID, as the mapping is not
created by firmware using unified bridge model.
c. flood_index() is not aligned to the new model, as this function will
be removed later.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Router interfaces (RIFs) constructed on top of VLAN-aware bridges are of
'VLAN' type, whereas RIFs constructed on top of VLAN-unaware bridges are of
'FID' type.
Currently 802.1Q FIDs are emulated using 802.1D FIDs, therefore VLAN RIFs
are emulated using FID RIFs. As part of converting the driver to use
unified bridge model, 802.1Q FIDs and VLAN RIFs will be used.
The egress FID is required for VLAN RIFs in Spectrum-2 and above, but not
in Spectrum-1, as in Spectrum-1 the mapping for VLAN RIFs is VID->FID,
while in other ASICs it is FID->FID. The reason for the change is that it
is more scalable to reuse the FID->FID entry than creating multiple
{Port, VID}->FID entries for the router port. Use the existing operation
structure to separate the configuration between different ASICs.
Add support for VLAN RIFs, most of the configurations are same to FID
RIFs.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After routing, a packet needs to perform an L2 lookup using the DMAC it got
from the routing and a FID. In unified bridge model, the egress FID
configuration needs to be performed by software.
It is configured by RITR for both sub-port RIFs and FID RIFs. Currently
FID RIFs already configure eFID. Add eFID configuration for sub-port RIFs.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The field 'vid' in RITR is reserved when unified bridge model is used
and the RIF's type is sub-port RIF. Instead, ingress VID is configured via
SVFA and egress VID is configured via REIV.
Set 'vid' to zero in RITR register for sub-port RIF when unified bridge
model is used.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After routing, the device always consults a table that determines the
packet's egress VID based on {egress RIF, egress local port}. In the
unified bridge model, it is up to software to maintain this table via REIV
register.
The table needs to be updated in the following flows:
1. When a RIF is set on a FID, need to iterate over the FID's {Port, VID}
list and issue REIV write to map the {RIF, Port} to the given VID.
2. When a {Port, VID} is mapped to a FID and the FID already has a RIF,
need to issue REIV write with a single record to map the {RIF, Port}
to the given VID.
REIV register supports a simultaneous update of 256 ports, so use this
capability for the first flow.
Handle the two above mentioned flows.
Add mlxsw_sp_fid_evid_map() function to handle egress VID classification
for both unicast and multicast. Layer 2 multicast configuration is already
done in the driver, just move it to the new function.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before layer 2 forwarding, the device classifies an incoming packet to
a FID. The classification is done based on one of the following keys:
1. FID
2. VNI (after decapsulation)
3. VID / {Port, VID}
After classification, the FID is known, but also all the attributes of
the FID, such as the router interface (RIF) via which a packet that
needs to be routed will ingress the router block.
In the legacy model, when a RIF was created / destroyed, it was
firmware's responsibility to update it in the previously mentioned FID
classification records. In the unified bridge model, this responsibility
moved to software.
The third classification requires to iterate over the FID's {Port, VID}
list and issue SVFA write with the correct mapping table according to the
port's mode (virtual or not). We never map multiple VLANs to the same FID
using VID->FID mapping, so such a mapping needs to be performed once.
When a new FID classification entry is configured and the FID already has
a RIF, set the RIF as part of SVFA configuration.
The reverse needs to be done when clearing a RIF from a FID. Currently,
clearing is done by issuing mlxsw_sp_fid_rif_set() with a NULL RIF pointer.
Instead, introduce mlxsw_sp_fid_rif_unset().
Note that mlxsw_sp_fid_rif_set() is called after the RIF is fully
operational, so it conforms to the internal requirement regarding
SVFA.irif_v: "Must not be set for a non-enabled RIF".
Do not set the ingress RIF for rFIDs, as the {Port, VID}->rFID entry is
configured by firmware when legacy model is used, a next patch will
handle this configuration for rFIDs and unified bridge model.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the new model, SFMR no longer configures both VNI->FID and FID->VNI
classifications, but only the later. The former needs to be configured via
SVFA.
Add SVFA configuration as part of vni_set() and vni_clear().
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using unified bridge model, firmware no longer configures the egress VID
"under the hood" and moves this responsibility to software.
For layer 2, this means that software needs to determine the egress VID
for both unicast (i.e., FDB) and multicast (i.e., MDB and flooding) flows.
Unicast FDB records and unicast LAG FDB records have new fields - "set_vid"
and "vid", set them. For records which point to router port, do not set
these fields.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
hasdata does not need to be initialized to zero. It will be assigned a
value in the following judgment conditions.
Signed-off-by: Li kunyu <kunyu@nfschina.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marc Kleine-Budde says:
====================
pull-request: can-next 2022-07-03
this is a pull request of 15 patches for net-next/master.
The first 2 patches are by Max Staudt and add the can327 serial CAN
driver along with a new line discipline ID.
The next patch is by me an fixes a typo in the ctucanfd driver.
The last 12 patches are by Dario Binacchi and integrate slcan CAN
serial driver better into the existing CAN driver API.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a private flag to the slcan driver to switch the
"err-rst-on-open" setting on and off.
"err-rst-on-open" on - Reset error states on opening command
"err-rst-on-open" off - Don't reset error states on opening command
(default)
The setting can only be changed if the interface is down:
ip link set dev can0 down
ethtool --set-priv-flags can0 err-rst-on-open {off|on}
ip link set dev can0 up
Link: https://lore.kernel.org/all/20220628163137.413025-11-dario.binacchi@amarulasolutions.com
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
As suggested by commit [1], now the driver uses the functions and the
data structures provided by the CAN network device driver interface.
Currently the driver doesn't implement a way to set bitrate for SLCAN
based devices via ip tool, so you'll have to do this by slcand or
slcan_attach invocation through the -sX parameter:
- slcan_attach -f -s6 -o /dev/ttyACM0
- slcand -f -s8 -o /dev/ttyUSB0
where -s6 in will set adapter's bitrate to 500 Kbit/s and -s8 to
1Mbit/s.
See the table below for further CAN bitrates:
- s0 -> 10 Kbit/s
- s1 -> 20 Kbit/s
- s2 -> 50 Kbit/s
- s3 -> 100 Kbit/s
- s4 -> 125 Kbit/s
- s5 -> 250 Kbit/s
- s6 -> 500 Kbit/s
- s7 -> 800 Kbit/s
- s8 -> 1000 Kbit/s
In doing so, the struct can_priv::bittiming.bitrate of the driver is not
set and since the open_candev() checks that the bitrate has been set, it
must be a non-zero value, the bitrate is set to a fake value (-1U)
before it is called.
Using the rtnl_lock()/rtnl_unlock() functions has become a bit more
tricky as the register_candev() function indirectly calls rtnl_lock()
via register_netdev(). To avoid a deadlock it is therefore necessary to
call rtnl_unlock() before calling register_candev(). The same goes for
the unregister_candev() function.
[1] commit 39549eef35 ("can: CAN Network device driver and Netlink interface")
Link: https://lore.kernel.org/all/20220628163137.413025-6-dario.binacchi@amarulasolutions.com
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Tested-by: Jeroen Hofstee <jhofstee@victronenergy.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Add parsing support by implementing struct mlx5e_tc_act for police
action.
TC rule with police actions is broken down into several rules in
different tables. One rule with the original match in the original
flow table, which set fte_id, do metering, and jump to the post_meter
table. If there are more police actions, more rules are created for
each of them. Besides, a last rule is created in the end.
In post_meter table, there are two pre-defined rules, one is to drop
packet if its packet color is RED, the other is to jump back to
post_act table. As fte_id is updated before jumping, the rule for next
meter is matched to do another round of metering (if there are
multiple meters in the flow rule). Otherwise, last fte_id is matched
and do the original actions.
Signed-off-by: Jianbo Liu <jianbol@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Ariel Levkovich <lariel@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
As a preparation for validating police action, adds flow_action to
parse state, which is to passed to parsing callbacks.
Signed-off-by: Jianbo Liu <jianbol@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Flow meter object monitors the packets rate for the flows it is
attached to, and color packets with GREEN or RED. The post meter table
is used to check the color. Packet is dropped if it's RED, or
forwarded to post_act table if GREEN.
Packet color will be set to 8 LSB of the register C5, so they are
reserved for metering, which are previously used for matching fte id.
Signed-off-by: Jianbo Liu <jianbol@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Ariel Levkovich <lariel@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
There are many definitions to get bits and mask for different types of
metadata register mapping, add generic macros to unify them.
Signed-off-by: Jianbo Liu <jianbol@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Ariel Levkovich <lariel@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Add functions to create and destroy flow meter aso object.
This object only supports the range allocation. 64 objects are
allocated at a time, and there are two meters in each object.
Usually only one meter is allocated for a flow, so bitmap is used
to manage these 128 meters.
TC police action is mapped to hardware meter. As the index is unique
for each police action, add APIs to allocate or free hardware meter by
the index. If the meter is already created, increment its refcnt,
otherwise create new one. If police action has different parameters,
update hardware meter accordingly.
Signed-off-by: Jianbo Liu <jianbol@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
The policing rate and burst from user are converted to flow meter
parameters in hardware. These parameters are set or modified by
ACCESS_ASO WQE, add function to support it.
Signed-off-by: Jianbo Liu <jianbol@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Ariel Levkovich <lariel@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
If flow meter aso object is supported, set the allocated range, and
initialize aso wqe.
The allocated range is indicated by log_meter_aso_granularity in HW
capabilities, and currently is 6.
Signed-off-by: Jianbo Liu <jianbol@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Maor Dickman <maord@nvidia.com>
Reviewed-by: Ariel Levkovich <lariel@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Add interfaces to use ASO object control channel. The channel consists
of a control SQ and CQ to which user can post ACCESS_ASO work requests
to modify ASO objects. The functions to get wqe from SQ, fill wqe,
post the request, and poll the completion of the work, are provided.
Signed-off-by: Jianbo Liu <jianbol@nvidia.com>
Reviewed-by: Ariel Levkovich <lariel@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Add a separate API to create SQ and CQ for advanced steering
operations (ASO).
Since the mlx5_en API to create these resources is strongly coupled
with netdev channels and datapath elements, this API provides an
alternative for creating send queues that are used for ASO.
Currently the API allows creating channels with 2 wqbbs only - meaning
the support will be for a single ACCESS_ASO wqe with data at a time.
Signed-off-by: Jianbo Liu <jianbol@nvidia.com>
Reviewed-by: Ariel Levkovich <lariel@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Enable or disable switchdev according to the eswitch mode set by
devlink command. So it is not changed by other functions anymore.
Signed-off-by: Chris Mi <cmi@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Currently, there are three eswitch modes, none, legacy and switchdev.
None is the default mode. Remove redundant none mode as eswitch mode
should always be either legacy mode or switchdev mode.
With this patch, there are two behavior changes:
1. Legacy becomes the default mode. When querying eswitch mode using
devlink, a valid mode is always returned.
2. When disabling sriov, the eswitch mode will not change, only vfs
are unloaded.
Signed-off-by: Chris Mi <cmi@nvidia.com>
Reviewed-by: Maor Dickman <maord@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Introduce flag to indicate if fdb table is created as a pre-step
to prepare for removing dependency between sriov and eswitch mode
in the downstream patches.
Signed-off-by: Chris Mi <cmi@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Eswitch vport acl namespace is needed when loading vfs. There is
no need to free and reallocate it when switching eswitch mode.
Introduce flag to indicate if it is created or not. When needed,
create it. Only free it when the driver is unloaded or in bare
metal mode.
Signed-off-by: Chris Mi <cmi@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Smatch complains about this function:
drivers/net/ethernet/mellanox/mlx5/core/eswitch.c:2000 mlx5_esw_unlock()
warn: inconsistent returns '&esw->mode_lock'.
Before commit ec2fa47d7b ("net/mlx5: Lag, use lag lock") there
used to be a matching mlx5_esw_lock() function and the lock and
unlock functions were symmetric. But now we take the lock
unconditionally and must unlock unconditionally as well.
As near as I can tell this is dead code and can just be deleted.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
This patch add support for phylink_mac_config dsa hook. It configures
the mac for MII/RMII modes. The RGMII mode will be added in the future
patches.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch add support for phylink_mac_link_up. It configures the mac
for the speed, flow control and duplex mode.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The internal phy of the LAN937x are capable of 100Mbps Full duplex. The
xMII port of switch is capable of 10Mbps Full & Half Duplex, 100Mbps
Full & Half Duplex and 1000Mbps Half duplex. xMII port also supports Tx
and Rx Flow control.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch add the support for port_max_mtu, port_change_mtu and
port_fast_age dsa functionality.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch register mdio-bus for the lan937x series switch. mdio read
and write uses the vphy for accessing the phy register.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
