It is fully legal for a controller to start handling busy-end interrupt
before it has signaled that the command has completed. So make sure
we do things in the proper order, Or it results that command interrupt
is ignored so it can cause unexpected operations. This is founded at some
toshiba emmc with the bellow warning.
"mmc0: Got command interrupt 0x00000001 even though
no command operation was in progress."
This issue has been also reported by Youssef TRIKI:
It is not specific to Toshiba devices, and happens with eMMC devices
as well as SD card which support Auto-CMD12 rather than CMD23.
Also, similar patch is submitted by:
Gwendal Grignou <gwendal@chromium.org>
Changes since v1:
Fixed conflict with the next of git.linaro.org/people/ulf.hansson/mmc.git
and Tested if issue is fixed again.
Signed-off-by: Hankyung Yu <hankyung.yu@lge.com>
Signed-off-by: Chanho Min <chanho.min@lge.com>
Tested-by: Youssef TRIKI <youssef.triki@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
For UHS cards we need the ability to switch voltages from 3.3V to
1.8V. Add support to the dw_mmc driver to handle this. Note that
dw_mmc needs a little bit of extra code since the interface needs a
special bit programmed to the CMD register while CMD11 is progressing.
This means adding a few extra states to the state machine to track.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Yuvaraj Kumar C D <yuvaraj.cd@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch makes use of mmc_regulator_get_supply() to handle
the vmmc and vqmmc regulators.Also it moves the code handling
the these regulators to dw_mci_set_ios().It turned on the vmmc
and vqmmc during MMC_POWER_UP and MMC_POWER_ON,and turned off
during MMC_POWER_OFF.
Signed-off-by: Yuvaraj Kumar C D <yuvaraj.cd@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Some controller is supporting actual clock on SD_CLK_CTRL :: DIV[7:0].
Renesas SH-Mobile SDHI doesn't support,
but, Renesas R-Car SDHI supports it.
This patch adds new TMIO_MMC_CLK_ACTUAL flag for it.
[Kuninori Morimoto: tidyuped for upstreaming]
Tested-by: Nguyen Xuan Nui <nx-nui@jinso.co.jp>
Tested-by: Hiep Cao Minh <cm-hiep@jinso.co.jp>
Signed-off-by: Shinobu Uehara <shinobu.uehara.xc@renesas.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Renesas R-Car SDHI should set reserved bits
on CTL_SDIO_STATUS register when writing.
This patch adds new TMIO_MMC_SDIO_STATUS_QUIRK flags
for this purpose
[Kuninori Morimoto: tidyuped for upstreaming
enabled this flags for all SH-Mobile/R-Car]
Tested-by: Nguyen Xuan Nui <nx-nui@jinso.co.jp>
Tested-by: Hiep Cao Minh <cm-hiep@jinso.co.jp>
Signed-off-by: Shinobu Uehara <shinobu.uehara.xc@renesas.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Renesas SDHI has "Multiple Block Transfer Mode" settings
on SD_CMD register which controls CMD12 automatically.
This patch cares it, because
CMD12 is not needed when CMD53 (= SD_IO_RW_EXTENDED)
[Kuninori Morimoto: tidyuped for upstreaming
enabled this flags for all SH-Mobile/R-Car]
Tested-by: Nguyen Xuan Nui <nx-nui@jinso.co.jp>
Tested-by: Hiep Cao Minh <cm-hiep@jinso.co.jp>
Signed-off-by: Shinobu Uehara <shinobu.uehara.xc@renesas.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Some eMMC and SD cards implement a DSR register that allows to tune
raise/fall times and drive strength of the CMD and DATA outputs.
The values to use depend on the card in use and the host.
It might be needed to reduce the drive strength to prevent voltage peaks
above the host's specification.
Implement a 'dsr' devicetree property that allows to specify the value
to set the DSR to. For non-dt setups the new members of mmc_host can be
set by board code.
This patch was initially authored by Sascha Hauer. It contains
improvements authored by Markus Niebel and Uwe Kleine-König.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Markus Niebel <Markus.Niebel@tq-group.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
eMMC card can support up to 7 physical partitions, including 2 boot,
1 RPMB and 4 GPs. Change MMC_NUM_PHY_PARTITION from 6 to 7, which is
the correct value.
Signed-off-by: Yi Sun <yi.y.sun@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch adds an include of linux/types.h to make sure bool is defined
before utilized in this header file.
Signed-off-by: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch fix spelling typo found in DocBook/kernel-api.xml.
It is because the file is generated from the source comments,
I have to fix the comments in source codes.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Per PCIe r3.0, sec 2.3.2, an endpoint may respond to a Configuration
Request with a Completion with Configuration Request Retry Status (CRS).
This terminates the Configuration Request.
When the CRS Software Visibility feature is disabled (as it is by default),
a Root Complex must handle a CRS Completion by re-issuing the Configuration
Request. This is invisible to software. From the CPU's point of view, an
endpoint that always responds with CRS causes a hang because the Root
Complex never supplies data to complete the CPU read.
When CRS Software Visibility is enabled, a Root Complex that receives a CRS
Completion for a read of the Vendor ID must return data of 0x0001. The
Vendor ID of 0x0001 indicates to software that the endpoint is not ready.
We now have more devices that require CRS Software Visibility. For
example, a PLX 8713 NT bridge may respond with CRS until it has been
configured via I2C, and the I2C configuration is completely independent of
PCI enumeration.
Enable CRS Software Visibility if it is supported. This allows a system
with such a device to work (though the PCI core times out waiting for it to
become ready, and we have to rescan the bus after it is ready).
This essentially reverts ad7edfe049 ("[PCI] Do not enable CRS Software
Visibility by default"). The failures that led to ad7edfe049 should be
addressed by 89665a6a71 ("PCI: Check only the Vendor ID to identify
Configuration Request Retry").
[bhelgaas: changelog]
Link: http://lkml.kernel.org/r/20071029061532.5d10dfc6@snowcone
Link: http://lkml.kernel.org/r/alpine.LFD.0.9999.0712271023090.21557@woody.linux-foundation.org
Signed-off-by: Rajat Jain <rajatxjain@gmail.com>
Signed-off-by: Rajat Jain <rajatjain@juniper.net>
Signed-off-by: Guenter Roeck <groeck@juniper.net>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Whether through HCI with BR/EDR or SMP with LE when authentication fails
we should also notify any pending Pair Device mgmt command. This patch
updates the mgmt_auth_failed function to take the actual hci_conn object
and makes sure that any pending pairing command is notified and cleaned
up appropriately.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Drivers supporting multiple clusters or multiple 'struct cpufreq_policy'
instances may need to keep per-policy data. If the core doesn't provide support
for that, they might do it in the most unoptimized way: 'per-cpu' data.
This patch adds another field in struct cpufreq_policy: 'driver_data'. It isn't
accessed by core and is for driver's internal use only.
Tested-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
John W. Linville says:
====================
pull request: wireless-next 2014-09-08
Please pull this batch of updates intended for the 3.18 stream...
For the mac80211 bits, Johannes says:
"Not that much content this time. Some RCU cleanups, crypto
performance improvements, and various patches all over,
rather than listing them one might as well look into the
git log instead."
For the Bluetooth bits, Gustavo says:
"The changes consists of:
- Coding style fixes to HCI drivers
- Corrupted ack value fix for the H5 HCI driver
- A couple of Enhanced L2CAP fixes
- Conversion of SMP code to use common L2CAP channel API
- Page scan optimizations when using the kernel-side whitelist
- Various mac802154 and and ieee802154 6lowpan cleanups
- One new Atheros USB ID"
For the iwlwifi bits, Emmanuel says:
"We have a new big thing coming up which is called Dynamic Queue
Allocation (or DQA). This is a completely new way to work with the
Tx queues and it requires major refactoring. This is being done by
Johannes and Avri. Besides this, Johannes disables U-APSD by default
because of APs that would disable A-MPDU if the association supports
U-ASPD. Luca contributed to the power area which he was cleaning
up on the way while working on CSA. A few more random things here
and there."
For the Atheros bits, Kalle says:
"For ath6kl we had two small fixes and a new SDIO device id.
For ath10k the bigger changes are:
* support for new firmware version 10.2 (Michal)
* spectral scan support (Simon, Sven & Mathias)
* export a firmware crash dump file (Ben & me)
* cleaning up of pci.c (Michal)
* print pci id in all messages, which causes most of the churn (Michal)"
Beyond that, we have the usual collection of various updates to ath9k,
b43, mwifiex, and wil6210, as well as a few other bits here and there.
Please let me know if there are problems!
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
inetpeer sequence numbers are no longer incremented, so no need to
check and flush the tree. The function that increments the sequence
number was already dead code and removed in in "ipv4: remove unused
function" (068a6e18). Remove the code that checks for a change, too.
Verifying that v4_seq and v6_seq are never incremented and thus that
flush_check compares bp->flush_seq to 0 is trivial.
The second part of the change removes flush_check completely even
though bp->flush_seq is exactly !0 once, at initialization. This
change is correct because the time this branch is true is when
bp->root == peer_avl_empty_rcu, in which the branch and
inetpeer_invalidate_tree are a NOOP.
Signed-off-by: Willem de Bruijn <willemb@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The OMAP version of the 8250 can actually use 1:1 serial8250_startup().
However it needs to be extended by a wake up irq which should to be
requested & enabled at ->startup() time and disabled at ->shutdown() time.
v2…v3: properly copy callbacks
v1…v2: add shutdown callback
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The flags field of struct uart_port can only be safely modified
if the port mutex is held; no other lock prevents concurrent
changes from corrupting the field.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The SoC has four fully functional UARTs which use the same programming
model. They are named UART_A, UART_B, UART_C and UART_AO (Always-On)
which cannot be powered off.
Signed-off-by: Carlo Caione <carlo@caione.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are currently no need to export default_stop_ok() as an API,
instead let's keep it local to the PM domain governor.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
There are no active users of this API. Let's remove it and if future
needs shows up we could consider to have a get/put API instead.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The pm_genpd_syscore_poweroff() API and pm_genpd_syscore_poweron() API
makes the pm_genpd_syscore_switch() API redundant.
Moreover, since there are no active users, let's just remove it.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The genpd dev_irq_safe configuration somewhat overlaps with the runtime
PM pm_runtime_irq_safe() option. Also, currently genpd don't have a
good way to deal with these device. So, until we figured out if and how
to support this in genpd, let's remove the option to configure it.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This patch allow the users of the 8250 infrastructure to define a
handler for RS485 configration.
If no handler is defined the 8250 driver will work as usual.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Acked-by: Alan Cox <alan@linux.intel.com>
--
v2:Change suggested by Alan "One Thousand Gnomes":
- Move rs485 structure further down on the uart_8250_port structure
drivers/tty/serial/8250/8250_core.c | 39 +++++++++++++++++++++++++++++++++++++
include/linux/serial_8250.h | 3 +++
2 files changed, 42 insertions(+)
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is useful for userspace to know that there not dealing with a regular
mouse but rather with a pointing stick (e.g. a trackpoint) so that
userspace can e.g. automatically enable middle button scrollwheel
emulation.
It is impossible to tell the difference from the evdev info without
resorting to putting a list of device / driver names in userspace, this is
undesirable.
Add a property which allows userspace to see if a device is a pointing
stick, and set it on all the pointing stick drivers.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Peter Hutterer <peter.hutterer@who-t.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Merge Linux 3.17-rc4 here so we have all the latest
fixes on next too. This also cleans up a few conflicts
when applying patches.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Conflicts:
drivers/usb/gadget/Makefile
drivers/usb/gadget/function/Makefile
drivers/usb/gadget/legacy/Makefile
drivers/usb/phy/phy-samsung-usb.h
Before the move the l2cap_chan the SMP context (smp_chan) didn't have
any kind of proper locking. The best there existed was the
HCI_CONN_LE_SMP_PEND flag which was used to enable mutual exclusion for
potential multiple creators of the SMP context.
Now that SMP has been converted to use the l2cap_chan infrastructure and
since the SMP context is directly mapped to a corresponding l2cap_chan
we get the SMP context locking essentially for free through the
l2cap_chan lock. For all callbacks that l2cap_core.c makes for each
channel implementation (smp.c in the case of SMP) the l2cap_chan lock is
held through l2cap_chan_lock(chan).
Since the calls from l2cap_core.c to smp.c are covered the only missing
piece to have the locking implemented properly is to ensure that the
lock is held for any other call path that may access the SMP context.
This means user responses through mgmt.c, requests to elevate the
security of a connection through hci_conn.c, as well as any deferred
work through workqueues.
This patch adds the necessary locking to all these other code paths that
try to access the SMP context. Since mutual exclusion for the l2cap_chan
access is now covered from all directions the patch also removes
unnecessary HCI_CONN_LE_SMP_PEND flag (once we've acquired the chan lock
we can simply check whether chan->smp is set to know if there's an SMP
context).
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The identity address update of all channels for an l2cap_conn needs to
take the lock for each channel, i.e. it's safest to do this by a
separate workqueue callback.
Previously this was partially solved by moving the entire SMP key
distribution behind a workqueue. However, if we want SMP context locking
to be correct and safe we should always use the l2cap_chan lock when
accessing it, meaning even smp_distribute_keys needs to take that lock
which would once again create a dead lock when updating the identity
address.
The simplest way to solve this is to have l2cap_conn manage the deferred
work which is what this patch does. A subsequent patch will remove the
now unnecessary SMP key distribution work struct.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
We'll soon use hci_disconnect() from places that are interested to know
whether the hci_send_cmd() really succeeded or not. This patch updates
hci_disconnect() to pass on any error returned from hci_send_cmd().
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Now that there are no more users of the l2cap_conn_shutdown API (since
smp.c switched to using hci_disconnect) we can simply remove it along
with all of it's l2cap_conn variables.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When hci_chan_del is called the disconnection routines get scheduled
through a workqueue. If there's any incoming ACL data before the
routines get executed there's a chance that a new hci_chan is created
and the disconnection never happens. This patch adds a new hci_conn flag
to indicate that we're in the process of driving the connection down. We
set the flag in hci_chan_del and check for it in hci_chan_create so that
no new channels are created for the same connection.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
There's no point in passing a "small" timeout to queue_delayed_work() to
try to get the callback faster scheduled. Passing 0 is perfectly valid
and will cause a shortcut to a direct queue_work().
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
It's natural to have *_get() functions that increment the reference
count of an object to return the object type itself. This way it's
simple to make a copy of the object pointer and increase the reference
count in a single step. This patch updates two such get() functions,
namely hci_conn_get() and l2cap_conn_get(), and updates the users to
take advantage of the new API.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Now that SMP has been converted to use fixed channels we've got a bit of
a problem with the hci_conn reference counting. So far the L2CAP code
has kept a reference for each L2CAP channel that was notified of the
connection. With SMP however this would mean that the connection is
never dropped even though there are no other users of it. Furthermore,
SMP already does its own hci_conn reference counting internally,
starting from a security or pairing request and ending with the key
distribution.
This patch makes L2CAP fixed channels default to the L2CAP core not
keeping a hci_conn reference for them. A new FLAG_HOLD_HCI_CONN flag is
added so that L2CAP users can declare an exception to this rule and hold
a reference even for their fixed channels. One such exception is the
L2CAP socket layer which does want a reference for each socket (e.g. an
ATT socket which uses a fixed channel).
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
A block_device may be attached to different gendisks and thus
different bdis over time. bdev_inode_switch_bdi() is used to switch
the associated bdi. The function assumes that the inode could be
dirty and transfers it between bdis if so. This is a bit nasty in
that it reaches into bdi internals.
This patch reimplements the function so that it writes out the inode
if dirty. This is a lot simpler and can be implemented without
exposing bdi internals.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jens Axboe <axboe@fb.com>
Two flags and one bdi_writeback field are no longer used. Remove
them.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <axboe@fb.com>
bdev_get_queue() returns the request_queue associated with the
specified block_device. blk_get_backing_dev_info() makes use of
bdev_get_queue() to determine the associated bdi given a block_device.
All the callers of bdev_get_queue() including
blk_get_backing_dev_info() assume that bdev_get_queue() may return
NULL and implement NULL handling; however, bdev_get_queue() requires
the passed in block_device is opened and attached to its gendisk.
Because an active gendisk always has a valid request_queue associated
with it, bdev_get_queue() can never return NULL and neither can
blk_get_backing_dev_info().
Make it clear that neither of the two functions can return NULL and
remove NULL handling from all the callers.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Chris Mason <clm@fb.com>
Cc: Dave Chinner <david@fromorbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
XMOS based USB DACs with native DSD support expose this feature via a USB
alternate setting. The audio format is either 32-bit raw or a 32-bit PCM format.
To utilize this feature on linux this patch introduces a new 32-bit DSD
sampleformat DSD_U32_LE.
A follow up patch will add a quirk for XMOS based devices to utilize the new format.
Further patches will add support to alsa-lib.
Signed-off-by: Jurgen Kramer <gtmkramer@xs4all.nl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Move resource retrieval from atmel_tc_alloc to tc_probe to avoid lately
reporting resource related issues when a TC block user request a TC block.
Moreover, resources retrieval are usually done in the probe function,
thus moving them add some consistency with other drivers.
Initialization is done once, ie not every time a tc block is requested.
If it fails, the device is not appended to the list of tc blocks.
Furhermore, the device id is retrieved at probe as well, avoiding parsing
DT every time the user requests of tc block.
Signed-off-by: Gaël PORTAY <gael.portay@gmail.com>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Linux already supports 802.11h, where the access point can tell the
client to reduce its transmission power. However, 802.11h is only
defined for 5 GHz, where the need for this is much smaller than on
2.4 GHz.
Cisco has their own solution, called DTPC (Dynamic Transmit Power
Control). Cisco APs on a controller sometimes but not always send
802.11h; they always send DTPC, even on 2.4 GHz. This patch adds support
for parsing and honoring the DTPC IE in addition to the 802.11h
element (they do not always contain the same limits, so both must
be honored); the format is not documented, but very simple.
Tested (on top of wireless.git and on 3.16.1) against a Cisco Aironet
1142 joined to a Cisco 2504 WLC, by setting various transmit power
levels for the given access points and observing the results.
The Wireshark 802.11 dissector agrees with the interpretation of the
element, except for negative numbers, which seem to never happen
anyway.
Signed-off-by: Steinar H. Gunderson <sgunderson@bigfoot.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Add quirk to make sure that a device is always polled for input events
even if it hasn't been opened.
This is needed for devices that disconnects from the bus unless the
interrupt endpoint has been polled at least once or when not responding
to an input event (e.g. after having shut down X).
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
