RFC2710 (MLDv1), section 3.7. says:
The length of a received MLD message is computed by taking the
IPv6 Payload Length value and subtracting the length of any IPv6
extension headers present between the IPv6 header and the MLD
message. If that length is greater than 24 octets, that indicates
that there are other fields present *beyond* the fields described
above, perhaps belonging to a *future backwards-compatible* version
of MLD. An implementation of the version of MLD specified in this
document *MUST NOT* send an MLD message longer than 24 octets and
MUST ignore anything past the first 24 octets of a received MLD
message.
RFC3810 (MLDv2), section 8.2.1. states for *listeners* regarding
presence of MLDv1 routers:
In order to be compatible with MLDv1 routers, MLDv2 hosts MUST
operate in version 1 compatibility mode. [...] When Host
Compatibility Mode is MLDv2, a host acts using the MLDv2 protocol
on that interface. When Host Compatibility Mode is MLDv1, a host
acts in MLDv1 compatibility mode, using *only* the MLDv1 protocol,
on that interface. [...]
While section 8.3.1. specifies *router* behaviour regarding presence
of MLDv1 routers:
MLDv2 routers may be placed on a network where there is at least
one MLDv1 router. The following requirements apply:
If an MLDv1 router is present on the link, the Querier MUST use
the *lowest* version of MLD present on the network. This must be
administratively assured. Routers that desire to be compatible
with MLDv1 MUST have a configuration option to act in MLDv1 mode;
if an MLDv1 router is present on the link, the system administrator
must explicitly configure all MLDv2 routers to act in MLDv1 mode.
When in MLDv1 mode, the Querier MUST send periodic General Queries
truncated at the Multicast Address field (i.e., 24 bytes long),
and SHOULD also warn about receiving an MLDv2 Query (such warnings
must be rate-limited). The Querier MUST also fill in the Maximum
Response Delay in the Maximum Response Code field, i.e., the
exponential algorithm described in section 5.1.3. is not used. [...]
That means that we should not get queries from different versions of
MLD. When there's a MLDv1 router present, MLDv2 enforces truncation
and MRC == MRD (both fields are overlapping within the 24 octet range).
Section 8.3.2. specifies behaviour in the presence of MLDv1 multicast
address *listeners*:
MLDv2 routers may be placed on a network where there are hosts
that have not yet been upgraded to MLDv2. In order to be compatible
with MLDv1 hosts, MLDv2 routers MUST operate in version 1 compatibility
mode. MLDv2 routers keep a compatibility mode per multicast address
record. The compatibility mode of a multicast address is determined
from the Multicast Address Compatibility Mode variable, which can be
in one of the two following states: MLDv1 or MLDv2.
The Multicast Address Compatibility Mode of a multicast address
record is set to MLDv1 whenever an MLDv1 Multicast Listener Report is
*received* for that multicast address. At the same time, the Older
Version Host Present timer for the multicast address is set to Older
Version Host Present Timeout seconds. The timer is re-set whenever a
new MLDv1 Report is received for that multicast address. If the Older
Version Host Present timer expires, the router switches back to
Multicast Address Compatibility Mode of MLDv2 for that multicast
address. [...]
That means, what can happen is the following scenario, that hosts can
act in MLDv1 compatibility mode when they previously have received an
MLDv1 query (or, simply operate in MLDv1 mode-only); and at the same
time, an MLDv2 router could start up and transmits MLDv2 startup query
messages while being unaware of the current operational mode.
Given RFC2710, section 3.7 we would need to answer to that with an MLDv1
listener report, so that the router according to RFC3810, section 8.3.2.
would receive that and internally switch to MLDv1 compatibility as well.
Right now, I believe since the initial implementation of MLDv2, Linux
hosts would just silently drop such MLDv2 queries instead of replying
with an MLDv1 listener report, which would prevent a MLDv2 router going
into fallback mode (until it receives other MLDv1 queries).
Since the mapping of MRC to MRD in exactly such cases can make use of
the exponential algorithm from 5.1.3, we cannot [strictly speaking] be
aware in MLDv1 of the encoding in MRC, it seems also not mentioned by
the RFC. Since encodings are the same up to 32767, assume in such a
situation this value as a hard upper limit we would clamp. We have asked
one of the RFC authors on that regard, and he mentioned that there seem
not to be any implementations that make use of that exponential algorithm
on startup messages. In any case, this patch fixes this MLD
interoperability issue.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow switch drivers to implement per-port Wake-on-LAN getter and
setters.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add an abstraction layer to suspend/resume switch devices, doing the
following split:
- suspend/resume the slave network devices and their corresponding PHY
devices
- suspend/resume the switch hardware using switch driver callbacks
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current code abuses ifdefs to determine if the selected ECC scheme
is supported by the running kernel. As a result the code is hard to read,
and it also fails to load as a module.
This commit removes all the ifdefs and instead introduces a function
omap2_nand_ecc_check() to check if the ECC is supported by using
IS_ENABLED(CONFIG_xxx).
Since IS_ENABLED() is true when a config is =y or =m, this change fixes the
module so it can be loaded with no issues.
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
* pci/enumeration:
PCI: Enable CRS Software Visibility for root port if it is supported
PCI: Check only the Vendor ID to identify Configuration Request Retry
* pci/misc:
PCI: Parenthesize PCI_DEVID and PCI_VPD_LRDT_ID parameters
PCI: Increase IBM ipr SAS Crocodile BARs to at least system page size
PCI/AER: Make <linux/aer.h> standalone includable
* pci/virtualization:
PCI: Use device flag helper functions
xen/pciback: Use PCI device flag helper functions
KVM: Use PCI device flag helper functions
PCI: Add device flag helper functions
PCI: Assume all Mellanox devices have broken INTx masking
Add an onfi_timing_mode_default field to nand_chip and nand_flash_dev in
order to support NAND timings definition for non-ONFI NAND.
NAND that support better timings mode than the default one have to define
a new entry in the nand_ids table.
The default timing mode should be deduced from timings description from
the datasheet and the ONFI specification
(www.onfi.org/~/media/ONFI/specs/onfi_3_1_spec.pdf, chapter 4.15
"Timing Parameters").
You should choose the closest mode that fit the timings requirements of
your NAND chip.
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
We cannot make struct qdisc_skb_cb bigger without impacting IPoIB,
or increasing skb->cb[] size.
Commit e0f31d8498 ("flow_keys: Record IP layer protocol in
skb_flow_dissect()") broke IPoIB.
Only current offender is sch_choke, and this one do not need an
absolutely precise flow key.
If we store 17 bytes of flow key, its more than enough. (Its the actual
size of flow_keys if it was a packed structure, but we might add new
fields at the end of it later)
Signed-off-by: Eric Dumazet <edumazet@google.com>
Fixes: e0f31d8498 ("flow_keys: Record IP layer protocol in skb_flow_dissect()")
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow blk-mq to pass an argument to the timeout handler to indicate
if we're timing out a reserved or regular command. For many drivers
those need to be handled different.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
Don't do a kmalloc from timer to handle timeouts, chances are we could be
under heavy load or similar and thus just miss out on the timeouts.
Fortunately it is very easy to just iterate over all in use tags, and doing
this properly actually cleans up the blk_mq_busy_iter API as well, and
prepares us for the next patch by passing a reserved argument to the
iterator.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
Now that we've changed the driver API on the submission side use the
opportunity to fix up the name on the completion side to fit into the
general scheme.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
When we call blk_mq_start_request from the core blk-mq code before calling into
->queue_rq there is a racy window where the timeout handler can hit before we've
fully set up the driver specific part of the command.
Move the call to blk_mq_start_request into the driver so the driver can start
the request only once it is fully set up.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
Pass an explicit parameter for the last request in a batch to ->queue_rq
instead of using a request flag. Besides being a cleaner and non-stateful
interface this is also required for the next patch, which fixes the blk-mq
I/O submission code to not start a time too early.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
Pull workqueue fix from Tejun Heo:
"create_singlethread_workqueue() is the old interface which is kept
around for backward compatibility - each should be reviewed to
determine whether singlethread usage was to save worker threads or for
ordering guarantee and whether it's depended upon by memory reclaim
path.
While adding NUMA support for unbound workqueues during v3.10, I
forgot to update it breaking the singlethread and ordering properties
on NUMA setups. The breakage was unfortunately rather subtle and went
without being reported until now.
The only missing piece is __WQ_ORDERED flag which makes the unbounded
workqueue use a single backend queue across different NUMA nodes.
It's fixed by making create_singlethread_workqueue() wrap
alloc_ordered_workqueue() so that possible future updates are
inherited automatically"
* 'for-3.17-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq:
workqueue: apply __WQ_ORDERED to create_singlethread_workqueue()
We want the fixes in there, and it resolves a merge issue with
drivers/iio/accel/bma180.c
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ->detach() callback for the PM domain has now been fully adopted,
thus there no users left of the acpi_dev_pm_detach() API. This allow us
to convert it into a static function.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
To maintain scalability let's add common methods to attach and detach
a PM domain for a device, dev_pm_domain_attach|detach().
Typically dev_pm_domain_attach() shall be invoked from subsystem level
code at the probe phase to try to attach a device to its PM domain.
The reversed actions may be done a the remove phase and then by
invoking dev_pm_domain_detach().
When attachment succeeds, the attach function should assign its
corresponding detach function to a new ->detach() callback added in the
struct dev_pm_domain.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Kevin Hilman <khilman@linaro.org>
Reviewed-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This patch introduces generic code to perform PM domain look-up using
device tree and automatically bind devices to their PM domains.
Generic device tree bindings are introduced to specify PM domains of
devices in their device tree nodes.
Backwards compatibility with legacy Samsung-specific PM domain bindings
is provided, but for now the new code is not compiled when
CONFIG_ARCH_EXYNOS is selected to avoid collision with legacy code.
This will change as soon as the Exynos PM domain code gets converted to
use the generic framework in further patch.
This patch was originally submitted by Tomasz Figa when he was employed
by Samsung.
Link: http://marc.info/?l=linux-pm&m=139955349702152&w=2
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Tested-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The intent of this callback is to simplify detachment of devices from
their PM domains. Further patches will show the benefit.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This patch adds support for exporting mout_hdmi and mout_mixer to device
tree. Access to those clocks is required to correctly setup HDMI module
on Exynos 4210 and 4x12 SoCs.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
CC: Mike Turquette <mturquette@linaro.org>
CC: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com>
This patch adds missing smmu_g2d clock implementation and updates
comment about Exynos4 clocks from 278-282 range. Those clocks are
available on all Exynos4 SoC series, so the misleading comment has been
removed.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com>
Add clock provider for clocks in DMC domain including EPLL and BPLL. The
DMC clocks are necessary for Exynos3 devfreq driver.
The DMC clock domain uses different address space (0x105C0000) than
standard clock domain (0x10030000 - 0x10050000). The difference is huge
enough to add new DT node for the clock provider, rather than extending
existing address space.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com>
Newer SoCs have two different AHB interconnect. The AHB 32 bits Matrix
interconnect (h32mx) has a clock that can be setup at the half of the h64mx
clock (which is mck). The h32mx clock can not exceed 90 MHz.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
This patch fixes following minor cleanup:
- Order the include files in alphabetical order.
- Fix description of state_off in extcon_gpio.h
- Add a descrition for check_on_resume in extcon_gpio.h
Signed-off-by: George Cherian <george.cherian@ti.com>
[Modify the name/description of patch to keep standary codiyg style by Chanwoo Choi]
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
This patch move sm5502.h header file from 'include/linux/extcon' to
'driver/extcon' because sm5502.h is used for driver/extcon/extcon-sm5502.c.
and remove duplicate license description.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
The recent conversion of saa7134 to vb2 unconvered a poll() bug that
broke the teletext applications alevt and mtt. These applications
expect that calling poll() without having called VIDIOC_STREAMON will
cause poll() to return POLLERR. That did not happen in vb2.
This patch fixes that behavior. It also fixes what should happen when
poll() is called when STREAMON is called but no buffers have been
queued. In that case poll() will also return POLLERR, but only for
capture queues since output queues will always return POLLOUT
anyway in that situation.
This brings the vb2 behavior in line with the old videobuf behavior.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The comment for start_streaming that tells the developer with which vb2 state
buffers should be returned to vb2 gave the wrong state. Very confusing.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The existing RGB555X pixel format is ill-defined in respect to its alpha
bit and its meaning is driver dependent. Create new standard ARGB555X
and XRGB555X variants with clearly defined meanings and make the
existing variant deprecated.
The new pixel formats 4CC values have been selected to match the DRM
4CCs for the same in-memory formats.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
There are some patches that depends on media-v3.16-rc6.
So, merge back from upstream before applying them.
* linus/master: (1123 commits)
drm/nouveau: ltc/gf100-: fix cbc issues on certain boards
drm/bochs: add missing drm_connector_register call
drm/cirrus: add missing drm_connector_register call
staging: vt6655: buffer overflow in ioctl
USB: storage: Add quirks for Entrega/Xircom USB to SCSI converters
USB: storage: Add quirk for Ariston Technologies iConnect USB to SCSI adapter
USB: storage: Add quirk for Adaptec USBConnect 2000 USB-to-SCSI Adapter
USB: EHCI: unlink QHs even after the controller has stopped
[SCSI] fix for bidi use after free
[SCSI] fix regression that accidentally disabled block-based tcq
[SCSI] libiscsi: fix potential buffer overrun in __iscsi_conn_send_pdu
drm/radeon: Fix typo 'addr' -> 'entry' in rs400_gart_set_page
drm/nouveau/runpm: fix module unload
drm/radeon/px: fix module unload
vgaswitcheroo: add vga_switcheroo_fini_domain_pm_ops
drm/radeon: don't reset dma on r6xx-evergreen init
drm/radeon: don't reset sdma on CIK init
drm/radeon: don't reset dma on NI/SI init
drm/radeon/dpm: fix resume on mullins
drm/radeon: Disable HDP flush before every CS again for < r600
...
Commit 46394fd01 (ACPI / hotplug: Move container-specific code out of
the core) removed the generation of "online" uevents for containers,
because "add" uevents are now generated for them automatically when
container system devices are registered. However, there are user
space tools that need to be notified when the container and all of
its children have been enumerated, which doesn't happen any more.
For this reason, add a mechanism allowing "online" uevents to be
generated for ACPI containers after enumerating the container along
with all of its children.
Fixes: 46394fd01 (ACPI / hotplug: Move container-specific code out of the core)
Reported-and-tested-by: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Cc: 3.14+ <stable@vger.kernel.org> # 3.14+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Aaron Tomlin recently posted patches [1] to enable checking the
stack canary on every task switch. Looking at the canary code, I
realized that every arch (except ia64, which adds some space for
register spill above the stack) shares a definition of
end_of_stack() that makes it the first long after the
threadinfo.
For stacks that grow down, this low address is correct because
the stack starts at the end of the thread area and grows toward
lower addresses. However, for stacks that grow up, toward higher
addresses, this is wrong. (The stack actually grows away from
the canary.) On these archs end_of_stack() should return the
address of the last long, at the highest possible address for the stack.
[1] http://lkml.org/lkml/2014/9/12/293
Signed-off-by: Chuck Ebbert <cebbert.lkml@gmail.com>
Link: http://lkml.kernel.org/r/20140920101751.6c5166b6@as
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Tested-by: James Hogan <james.hogan@imgtec.com> [metag]
Acked-by: James Hogan <james.hogan@imgtec.com>
Acked-by: Aaron Tomlin <atomlin@redhat.com>
Pull drm fixes from Dave Airlie:
"A bunch of radeon fixes for oops on module unload, and problems with
resetting the dma engine, one nouveau fix for black boxes in rendering
on my mbp retina, one sti fix, and a couple of intel fixes"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/nouveau: ltc/gf100-: fix cbc issues on certain boards
drm/bochs: add missing drm_connector_register call
drm/cirrus: add missing drm_connector_register call
drm/radeon: Fix typo 'addr' -> 'entry' in rs400_gart_set_page
drm/nouveau/runpm: fix module unload
drm/radeon/px: fix module unload
vgaswitcheroo: add vga_switcheroo_fini_domain_pm_ops
drm/radeon: don't reset dma on r6xx-evergreen init
drm/radeon: don't reset sdma on CIK init
drm/radeon: don't reset dma on NI/SI init
drm/radeon/dpm: fix resume on mullins
drm/radeon: Disable HDP flush before every CS again for < r600
drm/radeon: delete unused PTE_* defines
drm/i915: Add limited color range readout for HDMI/DP ports on g4x/vlv/chv
drm: sti: do not iterate over the info frame array
drm/i915: Fix SRC_COPY width on 830/845g
percpu_ref is currently based on ints and the number of refs it can
cover is (1 << 31). This makes it impossible to use a percpu_ref to
count memory objects or pages on 64bit machines as it may overflow.
This forces those users to somehow aggregate the references before
contributing to the percpu_ref which is often cumbersome and sometimes
challenging to get the same level of performance as using the
percpu_ref directly.
While using ints for the percpu counters makes them pack tighter on
64bit machines, the possible gain from using ints instead of longs is
extremely small compared to the overall gain from per-cpu operation.
This patch makes percpu_ref based on longs so that it can be used to
directly count memory objects or pages.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Kent Overstreet <kmo@daterainc.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Jonathan writes:
First round of IIO fixes for the 3.17 cycle.
* Fix an overwritten error return that can prevent deferred probing when
using of_iio_channel_get_by_name
* A series that deals with an incorrect reference count when the default
trigger is set within the main probe routine for a driver. Can result
in a double free if the trigger is changed.
* Fix a buglet with xilinx-xadc concerning setup of the address for an
aux channel.
* At91 adc driver could sometimes get a touchscreen reading rather than
the intended adc channel. This is fixed by using the channel data register
instead.
* Fix some ST magnetometer gain values that differ in production parts from
the prerelease ones used for driver development.
This feature is intended for archs having cache line larger then 64B.
Since our CQE/EQEs are generally 64B in those systems, HW will write
twice to the same cache line consecutively, causing pipe locks due to
he hazard prevention mechanism. For elements in a cyclic buffer, writes
are consecutive, so entries smaller than a cache line should be
avoided, especially if they are written at a high rate.
Reduce consecutive writes to same cache line in CQs/EQs, by allowing the
driver to increase the distance between entries so that each will reside
in a different cache line. Until the introduction of this feature, there
were two types of CQE/EQE:
1. 32B stride and context in the [0-31] segment
2. 64B stride and context in the [32-63] segment
This feature introduces two additional types:
3. 128B stride and context in the [0-31] segment (128B cache line)
4. 256B stride and context in the [0-31] segment (256B cache line)
Modify the mlx4_core driver to query the device for the CQE/EQE cache
line stride capability and to enable that capability when the host
cache line size is larger than 64 bytes (supported cache lines are
128B and 256B).
The mlx4 IB driver and libmlx4 need not be aware of this change. The PF
context behaviour is changed to require this change in VF drivers
running on such archs.
Signed-off-by: Ido Shamay <idos@mellanox.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ptr used to be a non __percpu pointer (result of a this_cpu_ptr
assignment, 7d720c3e4f ("percpu: add __percpu sparse annotations to
net")). Since d25398df59 ("net: avoid reloads in SNMP_UPD_PO_STATS"),
that's no longer the case, SNMP_UPD_PO_STATS uses this_cpu_add and ptr
is now __percpu.
Silence sparse warnings by preserving the original type and
annotation, and remove the out-of-date comment.
warning: incorrect type in initializer (different address spaces)
expected unsigned long long *ptr
got unsigned long long [noderef] <asn:3>*<noident>
warning: incorrect type in initializer (different address spaces)
expected void const [noderef] <asn:3>*__vpp_verify
got unsigned long long *<noident>
warning: incorrect type in initializer (different address spaces)
expected void const [noderef] <asn:3>*__vpp_verify
got unsigned long long *<noident>
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added netlink attrs to configure FOU encapsulation for GRE, netlink
handling of these flags, and properly adjust MTU for encapsulation.
ip_tunnel_encap is called from ip_tunnel_xmit to actually perform FOU
encapsulation.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes IP tunnel to support (secondary) encapsulation,
Foo-over-UDP. Changes include:
1) Adding tun_hlen as the tunnel header length, encap_hlen as the
encapsulation header length, and hlen becomes the grand total
of these.
2) Added common netlink define to support FOU encapsulation.
3) Routines to perform FOU encapsulation.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement fou_gro_receive and fou_gro_complete, and populate these
in the correponsing udp_offloads for the socket. Added ipproto to
udp_offloads and pass this from UDP to the fou GRO routine in proto
field of napi_gro_cb structure.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch provides a receive path for foo-over-udp. This allows
direct encapsulation of IP protocols over UDP. The bound destination
port is used to map to an IP protocol, and the XFRM framework
(udp_encap_rcv) is used to receive encapsulated packets. Upon
reception, the encapsulation header is logically removed (pointer
to transport header is advanced) and the packet is reinjected into
the receive path with the IP protocol indicated by the mapping.
Netlink is used to configure FOU ports. The configuration information
includes the port number to bind to and the IP protocol corresponding
to that port.
This should support GRE/UDP
(http://tools.ietf.org/html/draft-yong-tsvwg-gre-in-udp-encap-02),
as will as the other IP tunneling protocols (IPIP, SIT).
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some switch drivers (e.g: bcm_sf2) may have to communicate specific
workarounds or flags towards the PHY device driver. Allow switches
driver to be delegated that task by introducing a get_phy_flags()
callback which will do just that.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we have removed the need for the PHY_BRCM_100MBPS_WAR flag, we
can remove it from the GENET driver and the broadcom shared header file.
The PHY driver checks the PHY supported bitmask instead.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Broadcom BCM7xxx internal PHYs do not contain any useful revision
information in the low 4-bits of their MII_PHYSID2 (MII register 3)
which could allow us to properly identify them.
As a result, we need the actual hardware block integrating these PHYs:
GENET or the SF2 switch to tell us what revision they are built with. To
assist with that, add two helper macros for fetching the the PHY
revision and patch level from the struct phy_device::dev_flags.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
