If the device suffers a spurious reset during ATI, there is no point
in enduring any further retries. Instead, simply return successfully
from the polling loop.
In this case, the interrupt handler will intervene and recognize the
device has been reset. It then proceeds to initialize the device and
trigger ATI once more.
As part of this change, swap the order of status field evaluation to
match that of the interrupt handler, and correct a nearby off-by-one
error that causes an error message to suggest the final attempt will
be retried.
Fixes: e505edaedc ("Input: add support for Azoteq IQS7222A/B/C")
Signed-off-by: Jeff LaBundy <jeff@labundy.com>
Link: https://lore.kernel.org/r/20220626072412.475211-6-jeff@labundy.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
If the device suffers a spurious reset while reacting to a previous
spurious reset, the second reset interrupt is preempted because the
ACK_RESET bit is written last.
To solve this problem, write the ACK_RESET bit prior to writing any
other registers. This ensures that any registers written before the
second spurious reset will be rewritten.
Last but not least, the order in which the ACK_RESET bit is written
relative to the second filter beta register is important for select
variants of silicon. Enforce the correct order so as to not clobber
the system status register.
Fixes: e505edaedc ("Input: add support for Azoteq IQS7222A/B/C")
Signed-off-by: Jeff LaBundy <jeff@labundy.com>
Link: https://lore.kernel.org/r/20220626072412.475211-5-jeff@labundy.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Select variants of silicon silently mirror part of the event mask
register to the system setup register (0xD0), and vice versa. For
the following sequence:
1. Read registers 0xD0 onward and store their contents.
2. Modify the contents, including event mask fields.
3. Write registers 0xD0 onward with the modified contents.
4. Write register 0xD0 on its own again later, using the contents
from step 1 to populate any reserved fields.
...the event mask register (e.g. address 0xDA) has been corrupted
by writing register 0xD0 with contents that were made stale after
step 3.
To solve this problem, read register 0xD0 once more between steps
3 and 4. When register 0xD0 is written during step 4, the portion
which is mirrored to the event mask register already matches what
was written in step 3.
Fixes: e505edaedc ("Input: add support for Azoteq IQS7222A/B/C")
Signed-off-by: Jeff LaBundy <jeff@labundy.com>
Link: https://lore.kernel.org/r/20220626072412.475211-4-jeff@labundy.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The release cycle of any key mapped to a slider gesture relies upon
trailing interrupts generated by other unmasked sources, the timing
and presence of which are inconsistent.
To solve this problem, explicitly report a release cycle to emulate
a full keystroke. Also, unmask touch interrupts if the slider press
event is defined; this ensures the device reports a final interrupt
with coordinate = 0xFFFF once the finger is lifted.
As a result of how the logic has been refactored, the press/release
event can now be mapped to a GPIO. This is more convenient than the
previous solution, which required each channel within the slider to
specify the same GPIO.
As part of this change, use the device's resolution rather than its
number of interrupt status registers to more safely determine if it
is capable of reporting gestures.
Last but not least, make the code a bit simpler by eliminating some
unnecessarily complex conditional statements and a macro that could
be derived using information that is already available.
Fixes: e505edaedc ("Input: add support for Azoteq IQS7222A/B/C")
Signed-off-by: Jeff LaBundy <jeff@labundy.com>
Link: https://lore.kernel.org/r/20220626072412.475211-3-jeff@labundy.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
If a positive swipe/flick gesture is defined but the corresponding
negative gesture is not, the former is inadvertently disabled. Fix
this by gently refactoring the logic responsible for disabling all
gestures by default.
As part of this change, make the code a bit simpler by eliminating
a superfluous conditional check. If a slider event does not define
an enable control, the second term of the bitwise AND operation is
simply 0xFFFF.
Fixes: e505edaedc ("Input: add support for Azoteq IQS7222A/B/C")
Signed-off-by: Jeff LaBundy <jeff@labundy.com>
Link: https://lore.kernel.org/r/20220626072412.475211-2-jeff@labundy.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
As the second and last step of preparation to add support for more
PMICs in this driver, move the long press debounce mask to struct
mtk_pmic_regs and use that in mtk_pmic_keys_lp_reset_setup() instead
of directly using the definition.
While at it, remove the definition for MTK_PMIC_RST_DU_SHIFT as we
are able to calculate it dynamically and spares us some unnecessary
new definitions around for future per-PMIC variations of RST_DU_MASK.
Lastly, it was necessary to change the function signature of
mtk_pmic_keys_lp_reset_setup() to now pass a pointer to the main
mtk_pmic_regs structure, since that's where the reset debounce
mask now resides.
This commit brings no functional changes.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Link: https://lore.kernel.org/r/20220524093505.85438-3-angelogioacchino.delregno@collabora.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The commit 26623eea0d attempted to deal with potential leak of runtime
PM counter when opening the touchscreen device, however it ended up
erroneously dropping the counter in the case of successfully enabling the
device.
Let's address this by using pm_runtime_resume_and_get() and then executing
pm_runtime_put_sync() only when we fail to send "sense on" command to the
device.
Fixes: 26623eea0d ("Input: stmfts - fix reference leak in stmfts_input_open")
Reported-by: Pavel Machek <pavel@denx.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input fixes from Dmitry Torokhov:
"A small fixup to ili210x touchscreen driver, and updated maintainer
entry for the device tree binding of Mediatek 6779 keypad:
- fix reset timing of Ilitek touchscreens
- update maintainer entry of DT binding of Mediatek 6779 keypad"
* tag 'input-for-v5.18-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: ili210x - use one common reset implementation
Input: ili210x - fix reset timing
dt-bindings: input: mediatek,mt6779-keypad: update maintainer
Currently, when trying to suspend and resume with VirtualPS/2 VMMouse
there is an error message after resuming:
psmouse serio1: vmmouse: Unable to re-enable mouse when reconnecting, err: -6
and the mouse will no longer be operable, requiring full rescan to find a
another driver to use for the port.
This error is due to QEMU still generating PS2 events which the kernel is
not consuming until resume time, where they interfere with mouse
identification and ultimately resulting in an error getting
VMMOUSE_VERSION_ID.
Test scenario:
1) start virtual machine with qemu command "vmport=on"
2) click suspend botton to enter suspend mode
3) resume and observe the error message in the kernel logs
Let's fix this by disabling the vmmouse in its reset handler. This will
notify qemu to stop vmmouse and remove the handler.
Signed-off-by: Zongmin Zhou<zhouzongmin@kylinos.cn>
Reviewed-by: Zack Rusin <zackr@vmware.com>
Link: https://lore.kernel.org/r/20220322021046.1087954-1-zhouzongmin@kylinos.cn
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Rename ili251x_hardware_reset() to ili210x_hardware_reset(), change its
parameter from struct device * to struct gpio_desc *, and use it as one
single consistent reset implementation all over the driver. Also increase
the minimum reset duration to 12ms, to make sure the reset is really
within the spec.
Signed-off-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20220518210423.106555-1-marex@denx.de
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
According to Ilitek "231x & ILI251x Programming Guide" Version: 2.30
"2.1. Power Sequence", "T4 Chip Reset and discharge time" is minimum
10ms and "T2 Chip initial time" is maximum 150ms. Adjust the reset
timings such that T4 is 12ms and T2 is 160ms to fit those figures.
This prevents sporadic touch controller start up failures when some
systems with at least ILI251x controller boot, without this patch
the systems sometimes fail to communicate with the touch controller.
Fixes: 201f3c8035 ("Input: ili210x - add reset GPIO support")
Signed-off-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20220518204901.93534-1-marex@denx.de
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
If the device is a detachable (and therefore lacks full keyboard), we may
still want to load this driver because the device might have some other
buttons or switches (e.g. volume and power buttons or a tablet mode
switch). In such case we do not want to register the "main" keyboard device
to allow userspace detect when the detachable keyboard is disconnected and
adjust the system behavior for the tablet mode.
Originally it was suggested to simply skip keyboard registration if row and
columns properties didn't exist, but that approach did not convey the
intent strongly enough and also had a slight problem for migrating existing
DTBs without updating the kernel first, so it was decided to introduce new
google,cros-ec-keyb-switches to explicitly mark devices that only have
axillary buttons and switches.
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20220516183452.942008-3-swboyd@chromium.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Allow the driver to wake the system on key press if the "wakeup-source"
property is provided in the device tree. Using the LRADC as a wakeup
source requires keeping the AVCC domain active during sleep. Since this
has a nontrivial impact on power consumption (sometimes doubling it),
disable the LRADC wakeup source by default.
Signed-off-by: Ondrej Jirman <x@xff.cz>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Link: https://lore.kernel.org/r/20220424161328.61103-1-samuel@sholland.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The status of the keys connected to the KPDPWR_N and RESIN_N pins
is identified by reading corresponding bits in the interrupt real
time status register. If the status has changed by the time that
the interrupt is handled then a press event will be missed.
Maintain a last known status variable to find unbalanced release
events and simulate press events for each accordingly.
Signed-off-by: David Collins <collinsd@codeaurora.org>
Signed-off-by: Anjelique Melendez <quic_amelende@quicinc.com>
Link: https://lore.kernel.org/r/20220422191239.6271-6-quic_amelende@quicinc.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
On certain PMICs, an unexpected assertion of KPDPWR_DEB (the
positive logic hardware debounced power key signal) may be seen
during the falling edge of KPDPWR_N (i.e. a power key press) when
it occurs close to the rising edge of SLEEP_CLK. This then
triggers a spurious KPDPWR interrupt.
Handle this issue by adding software debouncing support to ignore
key events that occur within the hardware debounce delay after the
most recent key release event.
Signed-off-by: David Collins <collinsd@codeaurora.org>
Signed-off-by: Anjelique Melendez <quic_amelende@quicinc.com>
Link: https://lore.kernel.org/r/20220422191239.6271-5-quic_amelende@quicinc.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input fixes from Dmitry Torokhov:
- a new set of keycodes to be used by marine navigation systems
- minor fixes to omap4-keypad and cypress-sf drivers
* tag 'input-for-v5.18-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: add Marine Navigation Keycodes
Input: omap4-keypad - fix pm_runtime_get_sync() error checking
Input: cypress-sf - register a callback to disable the regulators
Variable ret is being assigned a value that is never read, it is
being re-assigned again in either path of the if statement. The
assignment is redundant and can be removed.
Cleans up clang scan build warning:
Although the value stored to 'ret' is used in the enclosing expression,
the value is never actually read from 'ret' [deadcode.DeadStores]
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Link: https://lore.kernel.org/r/20220418142457.84708-1-colin.i.king@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Select callers of iqs7222_parse_props() do not expect a child node
to be derived and returned via pointer. As such, these callers set
**child_node to NULL. However, this pointer is dereferenced in all
cases.
To solve this problem, dereference the pointer only for cases that
expect a child node in the first place. In these cases, the caller
provides a valid pointer.
Fixes: e505edaedc ("Input: add support for Azoteq IQS7222A/B/C")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jeff LaBundy <jeff@labundy.com>
Link: https://lore.kernel.org/r/20220417214132.497487-1-jeff@labundy.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
If fwnode_property_count_u32() returns a negative error code then,
because of type promotion, the "count > ARRAY_SIZE(pins)" condition
will be true. The negative "count" is type promoted to a high unsigned
size_t value.
That means the "else if (count < 0)" condition will always be false and
we don't print that error message or propagate the error code from
fwnode_property_count_u32() as intended.
Fix this by re-ordering the checks so that we check for negative first.
Fixes: e505edaedc ("Input: add support for Azoteq IQS7222A/B/C")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/20220412153954.GA15406@kili
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
