The Marvell PHY can blink the LEDs, simple on/off. All LEDs blink at
the same rate, and the reset default is 84ms per blink, which is
around 12Hz.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linux LEDs can be requested to perform hardware accelerated
blinking. Pass this to the PHY driver, if it implements the op.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a brightness function, so the LEDs can be controlled from
software using the standard Linux LED infrastructure.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linux LEDs can be software controlled via the brightness file in /sys.
LED drivers need to implement a brightness_set function which the core
will call. Implement an intermediary in phy_device, which will call
into the phy driver if it implements the necessary function.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Define common binding parsing for all PHY drivers with LEDs using
phylib. Parse the DT as part of the phy_probe and add LEDs to the
linux LED class infrastructure. For the moment, provide a dummy
brightness function, which will later be replaced with a call into the
PHY driver. This allows testing since the LED core might otherwise
reject an LED whose brightness cannot be set.
Add a dependency on LED_CLASS. It either needs to be built in, or not
enabled, since a modular build can result in linker errors.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the 1PPS output was enabled and then lan8841 was configured to be a
follower, then target clock which is used to generate the 1PPS was not
configure correctly. The problem was that for each adjustments of the
time, also the nanosecond part of the target clock was changed.
Therefore the initial nanosecond part of the target clock was changed.
The issue can be observed if both the leader and the follower are
generating 1PPS and see that their PPS are not aligned even if the time
is allined.
The fix consists of not modifying the nanosecond part of the target
clock when adjusting the time. In this way the 1PPS get also aligned.
Fixes: e4ed8ba08e ("net: phy: micrel: Add support for PTP_PF_PEROUT for lan8841")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If SFP module is not present, it is sensible to fail sfp_module_eeprom()
and sfp_module_eeprom_by_page() early to avoid excessive I2C transfers
which are garanteed to fail.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Ivan Bornyakov <i.bornyakov@metrotek.ru>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
sfp->i2c_block_size is initialized at SFP module insertion in
sfp_sm_mod_probe(). Because of that, if SFP module was never inserted
since boot, sfp_read() call will lead to zero-length I2C read attempt,
and not all I2C controllers are happy with zero-length reads.
One way to issue sfp_read() on empty SFP cage is to execute ethtool -m.
If SFP module was never plugged since boot, there will be a zero-length
I2C read attempt.
# ethtool -m xge0
i2c i2c-3: adapter quirk: no zero length (addr 0x0050, size 0, read)
Cannot get Module EEPROM data: Operation not supported
If SFP module was plugged then removed at least once,
sfp->i2c_block_size will be initialized and ethtool -m will fail with
different exit code and without I2C error
# ethtool -m xge0
Cannot get Module EEPROM data: Remote I/O error
Fix this by initializing sfp->i2_block_size at struct sfp allocation
stage so no wild sfp_read() could issue zero-length I2C read.
Signed-off-by: Ivan Bornyakov <i.bornyakov@metrotek.ru>
Fixes: 0d035bed2a ("net: sfp: VSOL V2801F / CarlitoxxPro CPGOS03-0490 v2.0 workaround")
Cc: stable@vger.kernel.org
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds support for the EDPD PHY tunable.
Per default EDPD is disabled in interrupt mode, the tunable can be used
to override this, e.g. if the link partner doesn't use EDPD.
The interval to check for energy can be chosen between 1000ms and
2000ms. Note that this value consists of the 1000ms phylib interval
for state machine runs plus the time to wait for energy being detected.
v2:
- consider that phylib core holds phydev->lock when calling the
phy tunable hooks
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a member edpd_max_wait_ms to the private data structure in preparation
of making the wait period configurable by supporting the edpd phy tunable.
v2:
- rename constant to EDPD_MAX_WAIT_DFLT_MS
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add flag edpd_mode_set_by_user in preparation of adding edpd phy tunable
support. This flag will allow users to override the default behavior
of edpd being disabled if interrupt mode is used.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clear edpd_enable if interupt mode is used, this avoids
having to check for PHY_POLL multiple times.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add helper smsc_phy_config_edpd() and explicitly clear bit
MII_LAN83C185_EDPWRDOWN is edpd_enable isn't set.
Boot loader may have left whatever value.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename the flag to edpd_enable, as we're not enabling energy but
edpd (energy detect power down) mode. In addition change the
type to a bit field member in preparation of adding further flags.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Provide phylink_expects_phy() to allow MAC drivers to check if it
is expecting a PHY to attach to. Since fixed-linked setups do not
need to attach to a PHY.
Provides a boolean value as to if the MAC should expect a PHY.
Returns true if a PHY is expected.
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Michael Sit Wei Hong <michael.wei.hong.sit@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/mediatek/mtk_ppe.c
3fbe4d8c0e ("net: ethernet: mtk_eth_soc: ppe: add support for flow accounting")
924531326e ("net: ethernet: mtk_eth_soc: add missing ppe cache flush when deleting a flow")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The KSZ9131RNX incorrectly shows EEE capabilities in its registers.
Although the "EEE control and capability 1" (Register 3.20) is set to 0,
indicating no EEE support, the "EEE advertisement 1" (Register 7.60) is
set to 0x6, advertising EEE support for 1000BaseT/Full and
100BaseT/Full.
This inconsistency causes PHYlib to assume there is no EEE support,
preventing control over EEE advertisement, which is enabled by default.
This patch resolves the issue by utilizing the ksz9477_get_features()
function to correctly set the EEE capabilities for the KSZ9131RNX. This
adjustment allows proper control over EEE advertisement and ensures
accurate representation of the device's capabilities.
Fixes: 8b68710a31 ("net: phy: start using genphy_c45_ethtool_get/set_eee()")
Reported-by: Marek Vasut <marex@denx.de>
Tested-by: Marek Vasut <marex@denx.de>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
dp83869 internally uses a look-up table for mapping supported delays in
nanoseconds to register values.
When specific delays are defined in device-tree, phy_get_internal_delay
does the lookup automatically returning an index.
The default case wrongly assigns the nanoseconds value from the lookup
table, resulting in numeric value 2000 applied to delay configuration
register, rather than the expected index values 0-7 (7 for 2000).
Ultimately this issue broke RX for 1Gbps links.
Fix default delay configuration by assigning the intended index value
directly.
Cc: stable@vger.kernel.org
Fixes: 736b25afe2 ("net: dp83869: Add RGMII internal delay configuration")
Co-developed-by: Yazan Shhady <yazan.shhady@solid-run.com>
Signed-off-by: Yazan Shhady <yazan.shhady@solid-run.com>
Signed-off-by: Josua Mayer <josua@solid-run.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20230323102536.31988-1-josua@solid-run.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When the PHY library calls phy_error() something bad has happened, and
we halt the PHY state machine. Calling phy_error() from the main state
machine however is not precise enough to know whether the issue is
reading the link status or starting auto-negotiation.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend the PTP programmable gpios to implement also PTP_PF_EXTTS
function. The pins can be configured to capture both of rising
and falling edge. Once the event is seen, then an interrupt is
generated and the LTC is saved in the registers.
This was tested using:
ts2phc -m -l 7 -s generic -f ts2phc.cfg
Where the configuration was the following:
[global]
ts2phc.pin_index 6
[eth2]
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a quirk for a copper SFP that identifies itself as "OEM"
"SFP-2.5G-T". This module's PHY is inaccessible, and can only run
at 2500base-X with the host without negotiation. Add a quirk to
enable the 2500base-X interface mode with 2500base-T support, and
disable autonegotiation.
Reported-by: Frank Wunderlich <frank-w@public-files.de>
Tested-by: Frank Wunderlich <frank-w@public-files.de>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Allow SFP quirks to override the Autoneg, Pause and Asym_Pause bits in
the support mask.
Some modules have an inaccessible PHY on which is only accessible via
2500base-X without Autonegotiation. We therefore want to be able to
clear the Autoneg bit. Rearrange sfp_parse_support() to allow a SFP
modes quirk to override this bit.
Tested-by: Frank Wunderlich <frank-w@public-files.de>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The Autoneg bit in the advertising bitmap and state->an_enabled are
always identical. state->an_enabled is now no longer used by any
drivers, so lets kill this duplication.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The Amlogic Meson internal PHY's have the same register layout as
certain SMSC PHY's (also for non-c22-standard registers). This seems
to be more than just coincidence. Apparently they also need the same
workaround for EDPD mode (energy detect power down). Therefore let's
reuse SMSC PHY driver functionality in the meson-gxl PHY driver.
Tested with a G12A internal PHY. I don't have GXL test hw,
therefore I replace only the callbacks that are identical in
the SMSC PHY driver.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Amlogic Meson internal PHY's have the same register layout as
certain SMSC PHY's (also for non-c22-standard registers). This seems
to be more than just coincidence. Apparently they also need the same
workaround for EDPD mode (energy detect power down). Therefore let's
export SMSC PHY driver functionality for use by the meson-gxl PHY
driver.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Chris Healy <healych@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew reports that the SFF modules on one of the ZII platforms do not
indicate link up due to the SFP code believing that LOS indicating that
there is no signal being received from the remote end, but in fact the
LOS signal is showing that there is signal.
What makes SFF modules different from SFPs is they typically have an
inverted LOS, which uncovered this issue. When we read the hardware
state, we mask it with state_hw_mask so we ignore anything we're not
interested in. However, we don't re-read when state_hw_mask changes,
leading to sfp->state being stale.
Arrange for a software poll of the module state after we have parsed
the EEPROM in sfp_sm_mod_probe() and updated state_*_mask. This will
generate any necessary events for signal changes for the state
machine as well as updating sfp->state.
Reported-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Fixes: 8475c4b70b ("net: sfp: re-implement soft state polling setup")
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bus ownership is wrong when using of_mdiobus_register() to register an mdio
bus. That function is not inline, so when it calls mdiobus_register() the wrong
THIS_MODULE value is captured.
Signed-off-by: Maxime Bizon <mbizon@freebox.fr>
Fixes: 90eff9096c ("net: phy: Allow splitting MDIO bus/device support from PHYs")
[florian: fix kdoc, added Fixes tag]
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the phy_disconnect() -> phy_stop() path, we will be forcibly setting
the PHY state machine to PHY_HALTED. This invalidates the old_state !=
phydev->state condition in phy_state_machine() such that we will neither
display the state change for debugging, nor will we invoke the
link_change_notify() callback.
Factor the code by introducing phy_process_state_change(), and ensure
that we process the state change from phy_stop() as well.
Fixes: 5c5f626bca ("net: phy: improve handling link_change_notify callback")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
of_gpio.h in this driver is solely used as a proxy to other headers.
This is incorrect usage of the of_gpio.h. Replace it .h with what
indeed is used in the code.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
GPY2xx devices need 3 seconds to fully switch out of loopback mode
before it can safely re-enter loopback mode. Implement timeout mechanism
to guarantee 3 seconds waited before re-enter loopback mode.
Signed-off-by: Xu Liang <lxu@maxlinear.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
